DATA SHEET COMPOUND TRANSISTOR FB1 SERIES on-chip resistor NPN silicon epitaxial transistor For mid-speed switching FEATURES PACKAGE DRAWING (UNIT: mm) • Up to 0.7 A current drive available • On-chip bias resistor • Low power consumption during drive QUALITY GRADES • Standard Please refer to “Quality Grades on NEC Semiconductor Devices” (Document No. C11531E) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications. FB1 SERIES LISTS Products Marking R1 (KΩ) R2 (KΩ) FB1A4A P30 − 10 FB1L2Q P31 0.47 4.7 FB1A3M P32 1.0 1.0 FB1F3P P33 2.2 10 FB1J3P P36 3.3 10 FB1L3N P34 4.7 10 FB1A4M P35 10 10 ABSOLUTE MAXIMUM RATINGS (Ta = 25°°C) Symbol Ratings Unit Collector to base voltage Parameter VCBO 30 V Collector to emitter voltage VCEO 25 V Emitter to base voltage VEBO 10 V Collector current (DC) IC(DC) 0.7 A IC(pulse) * 1.0 A IB(DC) 20 mA Total power dissipation PT 200 mW Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C Collector current (Pulse) Base current (DC) * PW≤10 ms, duty cycle≤50 % The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. D16180EJ1V0DS00 (1st edition) Date Published April 2002 N CP(K) Printed in Japan © 2002 1998 FB1 SERIES FB1A4A ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions MIN. TYP. VCB = 30 V, IE = 0 MAX. Unit 100 nA DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 300 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 − hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 DC current gain Collector saturation voltage Low level input voltage VCE(sat) ** VIL ** IC = 0.5 A, IB = 5 mA − 0.27 VCE = 5.0 V, IC = 100 µA 0.4 V 0.3 V − − Ω Input resistance R1 − E-to-B resistance R2 7 10 13 kΩ MIN. TYP. MAX. Unit 100 nA ** PW ≤ 350 µs, duty cycle ≤ 2 % FB1L2Q ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions VCB = 30 V, IE = 0 DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 150 400 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 700 − DC current gain hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 600 − Low level output voltage VOL ** VIN = 5.0 V, IC = 0.5 A VIL ** VCE = 5.0 V, IC = 100 µA 0.2 0.3 V 0.62 0.3 V Input resistance R1 329 470 611 Ω E-to-B resistance R2 3.29 4.7 6.11 kΩ MIN. TYP. MAX. Unit 100 nA Low level input voltage ** PW ≤ 350 µs, duty cycle ≤ 2 % FB1A3M ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions VCB = 30 V, IE = 0 DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 80 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 100 − DC current gain hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 − Low level output voltage VOL ** VIN = 5.0 V, IC = 0.5 A Low level input voltage VIL ** VCE = 5.0 V, IC = 100 µA 0.4 V 0.3 V Input resistance R1 0.7 1.0 1.3 kΩ E-to-B resistance R2 0.7 1.0 1.3 kΩ ** PW ≤ 350 µs, duty cycle ≤ 2 % 2 0.3 Data Sheet D16180EJ1V0DS FB1 SERIES FB1F3P ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions MIN. TYP. VCB = 30 V, IE = 0 MAX. Unit 100 nA DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 300 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 − DC current gain hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 Low level output voltage VOL ** VIN = 5.0 V, IC = 0.3 A 0.3 Low level input voltage VIL ** VCE = 5.0 V, IC = 100 µA 0.3 V − V Input resistance R1 1.54 2.2 2.86 kΩ E-to-B resistance R2 7 10 13 kΩ MIN. TYP. MAX. Unit 100 nA ** PW ≤ 350 µs, duty cycle ≤ 2 % FB1J3P ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions VCB = 30 V, IE = 0 DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 300 600 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 700 − DC current gain hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 600 − Low level output voltage VOL ** VIN = 5.0 V, IC = 0.2 A VIL ** VCE = 5.0 V, IC = 100 µA 0.14 0.3 V 0.6 0.3 V Input resistance R1 2.31 3.3 4.29 kΩ E-to-B resistance R2 7 10 13 kΩ MIN. TYP. MAX. Unit 100 nA Low level input voltage ** PW ≤ 350 µs, duty cycle ≤ 2 % FB1L3N ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions VCB = 30 V, IE = 0 DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 300 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 − DC current gain hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 − Low level output voltage VOL ** VIN = 5.0 V, IC = 0.2 A 0.3 V Low level input voltage VIL ** VCE = 5.0 V, IC = 100 µA 0.3 V Input resistance R1 3.29 4.7 6.11 kΩ E-to-B resistance R2 7 10 13 kΩ ** PW ≤ 350 µs, duty cycle ≤ 2 % Data Sheet D16180EJ1V0DS 3 FB1 SERIES FB1A4M ELECTRICAL CHARACTERISTICS (Ta = 25°°C) Parameter Collector cutoff current Symbol ICBO Conditions TYP. VCB = 30 V, IE = 0 MAX. Unit 100 nA DC current gain hFE1 ** VCE = 2.0 V, IC = 0.1 A 300 − DC current gain hFE2 ** VCE = 2.0 V, IC = 0.5 A 300 − hFE3 ** VCE = 2.0 V, IC = 0.7 A 135 VCE(sat) ** VIN = 5.0 V, IC = 0.2 A 0.3 VCE = 5.0 V, IC = 100 µA 0.3 V DC current gain Collector saturation voltage Low level input voltage VIL ** − V Input resistance R1 7 10 13 kΩ E-to-B resistance R2 7 10 13 kΩ ** PW ≤ 350 µs, duty cycle ≤ 2 % 4 MIN. Data Sheet D16180EJ1V0DS FB1 SERIES TYPICAL CHARACTERISTICS (Ta = 25°°C) Data Sheet D16180EJ1V0DS 5 FB1 SERIES RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact an NEC sales representative. Surface MOUNTING TYPE For details of the recommended soldering conditions, refer to the document Semiconductor Device Mounting Technology Manual (C10535E). Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 230°C, Time: 30 sec. max. (at 210°C or higher), Count: Once, Exposure limit: None * IR30-00 VPS Package peak temperature: 215°C, Time: 40 sec. max. (at 200°C or higher), Count: Once, Exposure limit: None * VP15-00 Partial heating Pin temperature: 300°C max., Time: 10 sec. max. Exposure limit: None * O * After opening the dry pack, store it at 25°C or less and 65% RH or less for the allowable storage period. Cautions 1. Do not use different soldering methods together (except for partial heating). 2. Prevent the resin surface temperature from being higher than the board temperature by 20°°C or more. 6 Data Sheet D16180EJ1V0DS FB1 SERIES [MEMO] Data Sheet D16180EJ1V0DS 7 FB1 SERIES • The information in this document is current as of July, 2001. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4