DATA SHEET MOS INTEGRATED CIRCUIT MC-458CB64ESB, 458CB64PSB 8M-WORD BY 64-BIT SYNCHRONOUS DYNAMIC RAM MODULE (SO DIMM) Description The MC-458CB64ESB and MC-458CB64PSB are 8,388,608 words by 64 bits synchronous dynamic RAM module (Small Outline DIMM) on which 4 pieces of 128M SDRAM: µPD45128163 are assembled. These modules provide high density and large quantities of memory in a small space without utilizing the surfacemounting technology on the printed circuit board. Decoupling capacitors are mounted on power supply line for noise reduction. Features • 8,388,608 words by 64 bits organization • Clock frequency and access time from CLK Part number MC-458CB64ESB-A10B ★ MC-458CB64PSB-A10B Clock frequency (MAX.) Access time from CLK CL = 3 100 MHz 7 ns CL = 2 67 MHz 8 ns CL = 3 100 MHz 7 ns CL = 2 67 MHz 8 ns /CAS Latency (MIN.) • Fully Synchronous Dynamic RAM, with all signals referenced to a positive clock edge • Pulsed interface • Possible to assert random column address in every cycle • Quad internal banks controlled by BA0 and BA1 (Bank Select) • Programmable burst-length (1, 2, 4, 8 and Full Page) • Programmable wrap sequence (Sequential / Interleave) • Programmable /CAS latency (2, 3) • Automatic precharge and controlled precharge • CBR (Auto) refresh and self refresh • Single +3.3 V ± 0.3 V power supply • LVTTL compatible • 4,096 refresh cycles/64 ms • Burst termination by Burst Stop command and Precharge command • 144-pin small outline dual in-line memory module (Pin pitch = 0.8 mm) • Unbuffered type • Serial PD The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. M12263EJAV0DS00 (10th edition) Date Published February 2000 NS CP(K) Printed in Japan The mark • shows major revised points. © 1996 MC-458CB64ESB, 458CB64PSB Ordering Information Part number Clock frequency Package Mounted devices MHz (MAX.) MC-458CB64ESB-A10B 100 MHz 144-pin Small Outline DIMM 4 pieces of µPD45128163G5 (Rev. E) (Socket Type) (10.16mm (400) TSOP (II)) Edge connector: Gold plated ★ MC-458CB64PSB-A10B 100 MHz 25.4 mm height 4 pieces of µPD45128163G5 (Rev. P) (10.16mm (400) TSOP (II)) 2 Data Sheet M12263EJAV0DS00 MC-458CB64ESB, 458CB64PSB Pin Configuration 144-pin Dual In-line Memory Module Socket Type (Edge connector: Gold plated) 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 Vss DQ 32 DQ 33 DQ 34 DQ 35 Vcc DQ 36 DQ 37 DQ 38 DQ 39 Vss DQMB4 DQMB5 Vcc A3 A4 A5 Vss DQ 40 DQ 41 DQ 42 DQ 43 Vcc DQ 44 DQ 45 DQ 46 DQ 47 Vss NC NC Vss DQ 0 DQ 1 DQ 2 DQ 3 VCC DQ 4 DQ 5 DQ 6 DQ 7 Vss DQMB0 DQMB1 VCC A0 A1 A2 Vss DQ 8 DQ 9 DQ 10 DQ 11 VCC DQ 12 DQ 13 DQ 14 DQ 15 Vss NC NC CLK0 CKE0 Vcc Vcc /RAS /CAS /WE NC /CS0 NC NC NC NC CLK1 Vss Vss NC NC NC NC VCC Vcc DQ 16 DQ 48 DQ 17 DQ 49 DQ 18 DQ 50 DQ 19 DQ 51 Vss Vss DQ 20 DQ 52 DQ 21 DQ 53 DQ 22 DQ 54 DQ 23 DQ 55 Vcc Vcc A6 A7 A8 BA0 (A13) Vss Vss A9 BA1 (A12) A10 A11 Vcc Vcc DQMB2 DQMB6 DQMB3 DQMB7 Vss Vss DQ 24 DQ 56 DQ 25 DQ 57 DQ 26 DQ 58 DQ 27 DQ 59 VCC Vcc DQ 28 DQ 60 DQ 29 DQ 61 DQ 30 DQ 62 DQ 31 DQ 63 Vss Vss SDA SCL VCC Vcc 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 Data Sheet M12263EJAV0DS00 /xxx indicates active low signal. A0 - A11 : Address Inputs [Row: A0 - A11, Column: A0 - A8] BA0(A13), BA1(A12): SDRAM Bank Select DQ0 - DQ63 : Data Inputs/Outputs CLK0, CLK1 : Clock Input CKE0 : Clock Enable Input /CS0 : Chip Select Input /RAS : Row Address Strobe /CAS : Column Address Strobe /WE : Write Enable DQMB0 - DQMB7 : DQ Mask Enable SDA : Serial Data I/O for PD SCL : Clock Input for PD VCC : Power Supply VSS : Ground NC : No Connection 3 MC-458CB64ESB, 458CB64PSB ★ Block Diagram /WE /CS0 LDQM DQMB0 DQ 0 /CS /WE DQMB4 DQ 32 DQ 0 DQ 1 DQ 1 DQ 33 DQ 1 DQ 2 DQ 2 DQ 34 DQ 2 DQ 3 DQ 3 DQ 35 DQ 3 DQ 4 DQ 4 DQ 36 DQ 4 DQ 5 DQ 5 DQ 37 DQ 5 DQ 6 DQ 6 DQ 38 DQ 6 DQ 7 DQ 7 DQ 39 DQ 7 UDQM D0 UDQM DQMB1 DQ 8 DQ 15 DQMB5 DQ 40 DQ 9 DQ 14 DQ 41 DQ 14 DQ 10 DQ 13 DQ 42 DQ 13 DQ 11 DQ 12 DQ 43 DQ 12 DQ 12 DQ 11 DQ 44 DQ 11 DQ 13 DQ 10 DQ 45 DQ 10 DQ 14 DQ 9 DQ 46 DQ 9 DQ 15 DQ 8 DQ 47 DQ 8 DQMB2 DQ 16 DQ 7 DQMB6 DQ 48 DQ 7 DQ 17 DQ 6 DQ 49 DQ 6 DQ 18 DQ 5 DQ 50 DQ 5 DQ 19 DQ 4 DQ 51 DQ 4 DQ 20 DQ 3 DQ 52 DQ 3 DQ 21 DQ 2 DQ 53 DQ 2 DQ 22 DQ 1 DQ 54 DQ 1 DQ 23 DQ 0 DQ 55 DQ 0 LDQM /CS /WE D1 UDQM DQMB3 D2 /CS LDQM /WE D3 UDQM DQ 24 DQ 8 DQ 25 DQ 9 DQ 57 DQ 9 DQ 26 DQ 10 DQ 58 DQ 10 DQ 27 DQ 11 DQ 59 DQ 11 DQ 28 DQ 12 DQ 60 DQ 12 DQ 29 DQ 13 DQ 61 DQ 13 DQ 30 DQ 14 DQ 62 DQ 14 DQ 31 DQ 15 DQ 63 DQ 15 DQ 8 10 Ω SERIAL PD CLK0 SCL SDA A1 /WE DQ 15 DQMB7 DQ 56 A0 /CS LDQM DQ 0 CLK : D0, D2 CLK : D1, D3 A2 CLK1 10pF A0 - A11 : D0 - D3 /RAS BA0 A13 : D0 - D3 /CAS /CAS : D0 - D3 BA1 A12 : D0 - D3 CKE0 CKE : D0 - D3 A0 - A11 VCC D0 - D3 C VSS D0 - D3 Remark D0 - D3: µPD45128163 (2M words × 16 bits × 4 banks) 4 Data Sheet M12263EJAV0DS00 /RAS : D0 - D3 MC-458CB64ESB, 458CB64PSB Electrical Specifications • All voltages are referenced to VSS (GND). • After power up, wait more than 100 µs and then, execute power on sequence and CBR (Auto) refresh before proper device operation is achieved. Absolute Maximum Ratings Parameter Symbol Condition Rating Unit Voltage on power supply pin relative to GND VCC –0.5 to +4.6 V Voltage on input pin relative to GND VT –0.5 to +4.6 V Short circuit output current IO 50 mA Power dissipation PD 4 W Operating ambient temperature TA 0 to +70 °C Storage temperature Tstg –55 to +125 °C Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Recommended Operating Conditions Parameter Symbol Condition MIN. TYP. MAX. Unit 3.3 3.6 V Supply voltage VCC 3.0 High level input voltage VIH 2.0 VCC + 0.3 V Low level input voltage VIL –0.3 + 0.8 V Operating ambient temperature TA 0 70 °C MAX. Unit pF Capacitance (TA = 25 °C, f = 1 MHz) Parameter Input capacitance Data input/output capacitance Symbol Test condition CI1 A0 - A11, BA0 (A13), BA1 (A12), /RAS, /CAS, /WE 30 CI2 CLK0 30 CI3 CKE0 30 CI4 /CS0 30 CI5 DQMB0 -DQMB7 10 CI/O DQ0 - DQ63 10 Data Sheet M12263EJAV0DS00 MIN. TYP. pF 5 MC-458CB64ESB, 458CB64PSB DC Characteristics (Recommended Operating Conditions unless otherwise noted) Parameter Operating current Precharge standby current ★ in power down mode Precharge standby current Symbol ICC1 ICC2P ICC2PS ICC2N in non power down mode power down mode Active standby current in ICC3P ICC3PS ICC3N non power down mode Notes mA 1 /CAS latency = 2 440 IO = 0 mA /CAS latency = 3 440 CKE ≤ VIL(MAX.), tCK = 15 ns 4 CKE ≤ 4 VIL(MAX.), tCK = ∞ CKE ≥ VIH(MIN.), tCK = 15 ns, /CS ≥ VIH(MIN.), 80 CKE ≥ VIH(MIN.), tCK = ∞, Input signals are stable. 32 CKE ≤ VIL(MAX.), tCK = 15 ns 20 CKE ≤ VIL(MAX.), tCK = ∞ 16 CKE ≥ VIH(MIN.), tCK = 15 ns, /CS ≥ VIH(MIN.), 120 ICC4 CKE ≥ VIH(MIN.), tCK = ∞, Input signals are stable. 80 tCK ≥ tCK(MIN.) , IO = 0 mA /CAS latency = 2 400 /CAS latency = 3 560 ICC5 /CAS latency = 2 880 /CAS latency = 3 880 tRC ≥ tRC(MIN.) ICC6 CKE ≤ 0.2 V Input leakage current II(L) VI = 0 to 3.6 V, All other pins not under test = 0 V Output leakage current IO(L) DOUT is disabled, VO = 0 to 3.6 V High level output voltage VOH IO = – 4.0 mA Low level output voltage VOL IO = + 4.0 mA Self refresh current Unit Burst length = 1, tRC ≥ tRC(MIN.) (Burst mode) CBR (Auto) refresh current MAX. mA mA mA mA Input signals are changed one time during 30 ns. ICC3NS Operating current MIN. Input signals are changed one time during 30 ns. ICC2NS Active standby current in Test condition mA 2 mA 3 8 mA –4 +4 µA – 1.5 + 1.5 µA 2.4 V 0.4 V Notes 1. ICC1 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, ICC1 is measured on condition that addresses are changed only one time during tCK(MIN.). 2. ICC4 depends on output loading and cycle rates. Specified values are obtained with the output open. In addition to this, ICC4 is measured on condition that addresses are changed only one time during tCK(MIN.). 3. ICC5 is measured on condition that addresses are changed only one time during tCK(MIN.). 6 Data Sheet M12263EJAV0DS00 MC-458CB64ESB, 458CB64PSB AC Characteristics (Recommended Operating Conditions unless otherwise noted) ★ Test Conditions Parameter AC high level input voltage / low level input voltage Input timing measurement reference level Value Unit 2.4 / 0.4 V 1.4 V 1 ns 1.4 V Transition time (Input rise and fall time) Output timing measurement reference level tCK tCH CLK tCL 2.4 V 1.4 V 0.4 V tSETUP tHOLD Input 2.4 V 1.4 V 0.4 V tAC tOH Output Data Sheet M12263EJAV0DS00 7 MC-458CB64ESB, 458CB64PSB Synchronous Characteristics Parameter Symbol -A10B MIN. Clock cycle time Access time from CLK Unit MAX. /CAS latency = 3 tCK3 10 ns /CAS latency = 2 tCK2 15 ns /CAS latency = 3 tAC3 7 ns 1 /CAS latency = 2 tAC2 8 ns 1 CLK high level width tCH 3.5 ns CLK low level width tCL 3.5 ns Data-out hold time tOH 3 ns Data-out low-impedance time tLZ 0 ns /CAS latency = 3 tHZ3 3 7 ns /CAS latency = 2 tHZ2 3 8 ns Data-in setup time tDS 2.5 ns Data-in hold time tDH 1 ns Address setup time tAS 2.5 ns Address hold time tAH 1 ns CKE setup time tCKS 2.5 ns CKE hold time tCKH 1 ns CKE setup time (Power down exit) tCKSP 2.5 ns Command (/CS0, /RAS, /CAS, /WE, tCMS 2.5 ns tCMH 1 ns Data-out high-impedance time DQMB0 - DQMB7) setup time Command (/CS0, /RAS, /CAS, /WE, DQMB0 - DQMB7) hold time Note 1. Output load Z = 50 Ω Output 50 pF 8 Note Data Sheet M12263EJAV0DS00 1 MC-458CB64ESB, 458CB64PSB Asynchronous Characteristics Parameter Symbol -A10B MIN. Unit MAX. REF to REF/ACT command period tRC 90 ACT to PRE command period tRAS 60 PRE to ACT command period tRP 30 ns Delay time ACT to READ/WRITE command tRCD 30 ns ACT(0) to ACT(1) command period tRRD 20 ns Data-in to PRE command period tDPL 10 ns Data-in to ACT(REF) command /CAS latency = 3 tDAL3 1CLK+30 ns period (Auto precharge) tDAL2 1CLK+30 ns tRSC 2 CLK tT 1 /CAS latency = 2 Mode register set cycle time Transition time Refresh time (4,096 refresh cycles) tREF Data Sheet M12263EJAV0DS00 Note ns 120,000 ns 30 ns 64 ms 9 MC-458CB64ESB, 458CB64PSB ★ Serial PD (1/2) Byte No. Function Described Hex Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Notes 0 Defines the number of bytes written into serial PD memory 80H 1 0 0 0 0 0 0 0 128 bytes 1 Total number of bytes of serial PD memory 08H 0 0 0 0 1 0 0 0 256 bytes 2 Fundamental memory type 04H 0 0 0 0 0 1 0 0 SDRAM 3 Number of rows 0CH 0 0 0 0 1 1 0 0 12 rows 4 Number of columns 09H 0 0 0 0 1 0 0 1 9 columns 5 Number of banks 01H 0 0 0 0 0 0 0 1 1 bank 6 Data width 40H 0 1 0 0 0 0 0 0 64 bits 7 Data width (continued) 00H 0 0 0 0 0 0 0 0 0 8 Voltage interface 01H 0 0 0 0 0 0 0 1 LVTTL 9 CL = 3 Cycle time -A10B A0H 1 0 1 0 0 0 0 0 10 ns 10 CL =3 Access time -A10B 70H 0 1 1 1 0 0 0 0 7 ns 11 DIMM configuration type 00H 0 0 0 0 0 0 0 0 Non-parity 12 Refresh rate/type 80H 1 0 0 0 0 0 0 0 Normal 13 SDRAM width 10H 0 0 0 1 0 0 0 0 ×16 14 Error checking SDRAM width 00H 0 0 0 0 0 0 0 0 None 15 Minimum clock delay 01H 0 0 0 0 0 0 0 1 1 clock 16 Burst length supported 8FH 1 0 0 0 1 1 1 1 1, 2, 4, 8, F 17 Number of banks on each SDRAM 04H 0 0 0 0 0 1 0 0 4 banks 18 /CAS latency supported 06H 0 0 0 0 0 1 1 0 2, 3 19 /CS latency supported 01H 0 0 0 0 0 0 0 1 0 20 /WE latency supported 01H 0 0 0 0 0 0 0 1 0 21 SDRAM module attributes 00H 0 0 0 0 0 0 0 0 22 SDRAM device attributes: General 0EH 0 0 0 0 1 1 1 0 23 CL = 2 Cycle time -A10B F0H 1 1 1 1 0 0 0 0 15 ns 24 CL = 2 Access time -A10B 80H 1 0 0 0 0 0 0 0 8 ns 00H 0 0 0 0 0 0 0 0 25-26 10 27 tRP(MIN.) -A10B 1EH 0 0 0 1 1 1 1 0 30 ns 28 tRRD(MIN.) -A10B 14H 0 0 0 1 0 1 0 0 20 ns 29 tRCD(MIN.) -A10B 1EH 0 0 0 1 1 1 1 0 30 ns 30 tRAS(MIN.) -A10B 3CH 0 0 1 1 1 1 0 0 60 ns Data Sheet M12263EJAV0DS00 MC-458CB64ESB, 458CB64PSB (2/2) Byte No. Function Described Hex Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Notes 31 Module bank density 10H 0 0 0 1 0 0 0 0 64 M bytes 32 Command and address signal setup -A10B time 25H 0 0 1 0 0 1 0 1 2.5 ns 33 Command and address signal hold time -A10B 10H 0 0 0 1 0 0 0 0 1 ns 34 Data signal input setup time -A10B 25H 0 0 1 0 0 1 0 1 2.5 ns 35 Data signal input hold time -A10B 10H 0 0 0 1 0 0 0 0 1 ns 00H 0 0 0 0 0 0 0 0 62 SPD revision -A10B 12H 0 0 0 1 0 0 1 0 63 Checksum for bytes 0 – 62 B5H 1 0 1 1 0 1 0 1 36-61 64-71 72 1.2 Manufacture’s JEDEC ID code Manufacturing location 73-90 Manufacture’s P/N 91-92 Revision code 93-94 Manufacturing date 95-98 Assembly serial number 99-125 Mfg specific 126 Intel specification frequency -A10B 66H 0 1 1 0 0 1 1 0 127 Intel specification /CAS latency support -A10B 06H 0 0 0 0 0 1 1 0 66 MHz Timing Chart Refer to the SYNCHRONOUS DRAM MODULE TIMING CHART Information (M13348E). Data Sheet M12263EJAV0DS00 11 MC-458CB64ESB, 458CB64PSB ★ Package Drawing 144 PIN DUAL IN-LINE MODULE (SOCKET TYPE) A (AREA B) Y M1 (AREA B) R N Q M L M2 (AREA A) H S A (OPTIONAL HOLES) U1 U2 C I B T E D A1 (AREA A) F ITEM A detail of A part W D2 D1 X V MILLIMETERS 67.6 A1 67.6±0.15 B 23.2 C 29.0 D 4.6 D1 1.5±0.10 D2 4.0 E 32.8 F 3.7 H 0.8(T.P.) I 3.3 L 20.0 M 25.4±0.15 M1 3.4 M2 22.0 N 3.8 MAX. Q R2.0 R 4.0±0.10 S φ 1.8 T 1.0±0.1 U1 3.2 MIN. U2 4.0 MIN. V 0.25 MAX. W 0.6±0.05 Y 2.0 MIN. M144S-80A10 12 Data Sheet M12263EJAV0DS00 MC-458CB64ESB, 458CB64PSB [MEMO] Data Sheet M12263EJAV0DS00 13 MC-458CB64ESB, 458CB64PSB [MEMO] 14 Data Sheet M12263EJAV0DS00 MC-458CB64ESB, 458CB64PSB NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to V DD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. Data Sheet M12263EJAV0DS00 15 MC-458CB64ESB, 458CB64PSB CAUTION FOR HANDLING MEMORY MODULES When handling or inserting memory modules, be sure not to touch any components on the modules, such as the memory IC, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on these components to prevent damaging them. When re-packing memory modules, be sure the modules are NOT touching each other. Modules in contact with other modules may cause excessive mechanical stress, which may damage the modules. • The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. • NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. • Descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. • While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. • NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. M7 98. 8