TI TLC59108

TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
8-BIT Fm+ I2C-BUS CONSTANT-CURRENT LED SINK DRIVER
FEATURES
1
• Eight LED Drivers (Each Output Programmable
At Off, On, Programmable LED Brightness,
Programmable Group Dimming/Blinking Mixed
With Individual LED Brightness
• Eight Constant-Current Open-Drain Output
Channels
• 256-Step (8-Bit) Linear Programmable
Brightness Per LED Output Varying From Fully
Off (Default) to Maximum Brightness Using a
97-kHz PWM Signal
• 256-Step Group Brightness Control Allows
General Dimming (Using a 190-Hz PWM Signal
From Fully Off to Maximum Brightness
(Default)
• 256-Step Group Blinking With Frequency
Programmable From 24 Hz to 10.73 s and Duty
Cycle From 0% to 99.6%
• Four Hardware Address Pins Allow 14
TLC59108 Devices to be Connected to the
Same I2C Bus
• Four Software-Programmable I2C Bus
Addresses (One LED Group Call Address and
Three LED Sub Call Addresses) Allow Groups
of Devices to be Addressed at the Same Time
in Any Combination. For Example, One
Register Used for All Call, so That All the
TLC59108 Devices on the I2C Bus Can be
Addressed at the Same Time, and the Second
Register Can be Used for Three Different
Addresses so That One-Third of All Devices on
the Bus Can be Addressed at the Same Time
in a Group.
• Software Enable and Disable for I2C Bus
Address
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Software Reset Feature (SWRST Call) Allows
Device to be Reset Through I2C Bus
Up to 14 Possible Hardware-Adjustable
Individual I2C Bus Addresses Per Device, So
That Each Device Can Be Programmed
Open-Load/Overtemperature Detection Mode
to Detect Individual LED Errors
Output State Change Programmable on the
Acknowledge or the Stop Command to Update
Outputs Byte by Byte or All at the Same Time
(Default to Change on Stop)
Output Current Adjusted Through an External
Resistor
Constant Output Current Range: 10 mA to
120 mA
Maximum Output Voltage: 17 V
25-MHz Internal Oscillator Requires No
External Components
1-MHz Fast Mode Plus Compatible I2C Bus
Interface With 30-mA High Drive Capability on
SDA Output for Driving High-Capacitive Buses
Internal Power-On Reset
Noise Filter on SCL/SDA Inputs
No Glitch on Power Up
Active-Low Reset
Supports Hot Insertion
Low Standby Current
3.3-V or 5-V Supply Voltage
5.5-V Tolerant Inputs
Offered in 20-Pin TSSOP (PW) and QFN (RGY)
Packages
–40°C to 85°C Operation
DESCRIPTION/ORDERING INFORMATION
The TLC59108 is an I2C bus controlled 8-bit LED driver that is optimized for red/green/blue/amber (RGBA) color
mixing and backlight application for amusement products. Each LED output has its own 8-bit resolution
(256 steps) fixed-frequency individual PWM controller that operates at 97 kHz, with a duty cycle that is adjustable
from 0% to 99.6%. The individual PWM controller allows each LED to be set to a specific brightness value. An
additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of 190 Hz and an
adjustable frequency between 24 Hz to once every 10.73 seconds, with a duty cycle that is adjustable from 0%
to 99.6%. The group PWM controller dims or blinks all LEDs with the same value.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
Each LED output can be off, on (no PWM control), or set at its individual PWM controller value at both individual
and group PWM controller values.
The TLC59108 is one of the first LED controller devices in a new Fast-mode Plus (Fm+) family. Fm+ devices
offer higher frequency (up to 1 MHz) and longer, more densely populated bus operation (up to 4000 pF).
Software programmable LED group and three Sub Call I2C bus addresses allow all or defined groups of
TLC59108 devices to respond to a common I2C bus address, allowing for example, all red LEDs to be turned on
or off at the same time or marquee chasing effect, thus minimizing I2C bus commands. Four hardware address
pins allow up to 14 devices on the same bus.
The Software Reset (SWRST) call allows the master to perform a reset of the TLC59108 through the I2C bus,
identical to the Power-On Reset (POR) that initializes the registers to their default state, causing the outputs to
be set high (LED off). This allows an easy and quick way to reconfigure all device registers to the same
condition.
ORDERING INFORMATION (1)
PACKAGE (2)
TA
–40°C to 85°C
(1)
(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING
QFN – RGY
Reel of 1000
TLC59108IRGYR
Y59108
TSSOP – PW
Reel of 2000
TLC59108IPWR
Y59108
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
BLOCK DIAGRAM
A0 A1 A2 A3
SCL
SDA
Input Filter
I2C Bus Control
REXT
OUT0
OUT1
OUT6
OUT7
I/O Regulator
Output Driver and Error Detection
RESET
Power-On
Reset Control
LED State
Select Register
PWM Register X
Brightness Control
97 kHz
24.3 kHz
25-MHz
Oscillator
GRPFRQ
Register
GRPPWM
Register
190 kHz
0 = Permanently off
1 = Permanently on
VCC
GND
2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
RGY PACKAGE
(TOP VIEW)
PW PACKAGE
(TOP VIEW)
REXT
A0
A1
A2
A3
OUT0
OUT1
GND
OUT2
OUT3
VCC
SDA
SCL
RESET
GND
OUT7
OUT6
GND
OUT5
OUT4
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
10
A0
A1
A2
A3
OUT0
OUT1
GND
OUT2
REXT
VCC
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
OUT3
SDA
SCL
RESET
GND
OUT7
OUT6
GND
OUT5
11
OUT4
TERMINAL FUNCTIONS
TERMINAL
(1)
NAME
PW/RGY
PIN NO.
I/O (1)
DESCRIPTION
A0
2
I
Address input 0
A1
3
I
Address input 1
A2
4
I
Address input 2
A3
5
I
Address input 3
GND
8, 13, 16
OUT0
6
O
Ground
Constant current output 0, LED on at low
OUT1
7
O
Constant current output 1, LED on at low
OUT2
9
O
Constant current output 2, LED on at low
OUT3
10
O
Constant current output 3, LED on at low
OUT4
11
O
Constant current output 4, LED on at low
OUT5
12
O
Constant current output 5, LED on at low
OUT6
14
O
Constant current output 6, LED on at low
OUT7
15
O
Constant current output 7, LED on at low
RESET
17
I
Active-low reset input
REXT
1
SCL
18
I
Input terminal used to connect an external resistor for setting up all output currents
SDA
19
I/O
VCC
20
Serial clock input
Serial data input/output
Power supply
I = input, O = output
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
0
7
V
Input voltage range
–0.4
7
V
VO
Output voltage range
–0.5
IO
Output current
θJA
Thermal impedance, junction to free air (2)
TJ
Junction temperature range
Tstg
Storage temperature range
VCC
Supply voltage range
VI
(1)
(2)
UNIT
20
V
120
mA
83
°C/W
–40
150
°C
–55
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS (1)
MIN
MAX
UNIT
VCC
Supply voltage
3
5.5
V
VIH
High-level input voltage
SCL, SDA, RESET, A0, A1, A2, A3
0.7 × VCC
VCC
V
VIL
Low-level input voltage
SCL, SDA, RESET, A0, A1, A2, A3
0
0.3 × VCC
V
VO
Supply voltage to output pins
OUT0 to OUT7
17
V
IOL
Low-level output current sink
SDA
IO
Output current
OUT0 to OUT7
TA
Operating free-air temperature
(1)
4
VCC = 3 V
20
VCC = 3 V
30
mA
5
120
mA
–40
85
°C
All unused inputs of the device must be held at VCC or GND to ensure proper device operation.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
ELECTRICAL CHARACTERISTICS
VCC = 3 V to 5.5 V, TA = –40°C to 85°C (unless otherwise noted)
PARAMETER
II
TEST CONDITIONS
Input/output leakage
current
SCL, SDA, A0,
A1, A2, A3,
RESET
VI = VCC or GND
Output leakage current
OUT0 to OUT7
VO = 17 V, TJ = 25°C
MIN
TYP (1)
MAX
UNIT
±0.3
µA
0.5
µA
VPOR
Power-on reset voltage
IOL
Low-level output current
SDA
IO(1)
Output current 1
OUT0 to OUT7
VO = 0.6 V, Rext = 720 Ω, CG = 0.992
Output current error
OUT0 to OUT7
IO = 26 mA, VO = 0.6 V, Rext = 720 Ω,
TJ = 25°C
±8
%
Output channel to
channel current error
OUT0 to OUT7
IO = 26 mA, VO = 0.6 V, Rext = 720 Ω,
TJ = 25°C
±3
%
Output current 2
OUT0 to OUT7
VO = 0.8 V, Rext = 360 Ω, CG = 0.992
Output current error
OUT0 to OUT7
IO = 52 mA, VO = 0.8 V, Rext = 360 Ω,
TJ = 25°C
±8
%
Output channel to
channel current error
OUT0 to OUT7
IO = 52 mA, VO = 0.8 V, Rext = 360 Ω,
TJ = 25°C
±3
%
IOUT vs
VOUT
Output current vs output
voltage regulation
OUT0 to OUT7
IOUT,Th1
Threshold current 1 for
error detection
OUT0 to OUT7
IOUT,target = 26 mA
0.5 ×
ITARGET
%
IOUT,Th2
Threshold current 2 for
error detection
OUT0 to OUT7
IOUT,target = 52 mA
0.5 ×
ITARGET
%
IOUT,Th3
Threshold current 3 for
error detection
OUT0 to OUT7
IOUT,target = 104 mA
0.5 ×
ITARGET
%
IO(2)
2.5
VCC = 3 V, VOL = 0.4 V
20
VCC = 5 V, VOL = 0.4 V
30
V
mA
26
mA
52
VO = 1 V to 3 V, IO = 26 mA
mA
±0.1
VO = 3 V to 5.5 V, IO = 26 mA to 120 mA
(2)
%/V
±1
TSD
Overtemperature shutdown
THYS
Restart hysteresis
Ci
Input capacitance
SCL, A0, A1,
A2, A3, RESET
VI = VCC or GND
5
pF
Cio
Input/output capacitance
SDA
VI = VCC or GND
5
pF
ICC
(1)
(2)
150
175
200
15
Supply current
VCC = 5.5 V
°C
°C
OUT0 to OUT7 = OFF,
Rext = Open
17
OUT0 to OUT7 = OFF,
Rext = 720 Ω
20
OUT0 to OUT7 = OFF,
Rext = 360 Ω
23
OUT0 to OUT7 = OFF,
Rext = 180 Ω
28
OUT0 to OUT7 = ON,
Rext = 720 Ω
21
OUT0 to OUT7 = ON,
Rext = 360 Ω
23
OUT0 to OUT7 = ON,
Rext = 180 Ω
28
mA
All typical values are at TA = 25°C.
Specified by design
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
TIMING REQUIREMENTS
TA = –40°C to 85°C
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
FAST MODE PLUS
I2C BUS
MIN
MAX
MIN
MAX
MIN
MAX
0
100
0
400
0
1000
UNIT
I2C Interface
fSCL
SCL clock frequency (1)
tBUF
I2C bus free time between stop and
start
4.7
1.3
0.5
µs
tHD;STA
Hold time (repeated) Start condition
4
0.6
0.26
µs
tSU;STA
Set-up time for a repeated Start
condition
4.7
0.6
0.26
µs
tSU;STO
Set-up time for Stop condition
4
0.6
0.26
µs
tHD;DAT
Data hold time
0
0
0
tVD;ACK
Data valid acknowledge time (2)
tVD;DAT
kHz
ns
0.1
0.9
0.05
0.45
µs
0.1
0.9
0.05
0.45
µs
0.3
3.45
Data valid time (3)
0.3
3.45
tSU;DAT
Data set-up time
250
100
50
ns
tLOW
Low period of the SCL clock
4.7
1.3
0.5
µs
tHIGH
High period of the SCL clock
4
0.6
0.26
µs
tf
Fall time of both SDA and SCL
signals (4) (5)
300
20+0.1Cb (6)
300
120
ns
tr
Rise time of both SDA and SCL
signals
1000
20+0.1Cb (6)
300
120
ns
tSP
Pulse width of spikes that must be
suppressed by the input filter (7)
50
50
ns
50
Reset
tW
Reset pulse width
tREC
Reset recovery time
tRESET
Time to reset (8) (9)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
6
10
10
10
ns
0
0
0
ns
400
400
400
ns
Minimum SCL clock frequency is limited by the bus time-out feature, which resets the serial bus interface if either SDA or SCL is held
low for a minimum of 25 ms. Disable bus time-out feature for DC operation.
tVD;ACK = time for Acknowledgement signal from SCL low to SDA (out) low.
tVD;DAT = minimum time for SDA data out to be valid following SCL low.
A master device must internally provide a hold time of at least 300 ns for the SDA signal (refer to the VIL of the SCL signal) in order to
bridge the undefined region of SCLs falling edge.
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time (tf) for the SDA output stage is specified
at 250 ns. This allows series protection resistors to be connected between the SDA and the SCL pins and the SDA/SCL bus lines
without exceeding the maximum specified tf.
Cb = total capacitance of one bus line in pF.
Input filters on the SDA and SCL inputs suppress noise spikes less than 50 ns
Resetting the device while actively communicating on the bus may cause glitches or errant Stop conditions.
Upon reset, the full delay will be the sum of tRESET and the RC time constant of the SDA bus.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
PARAMETER MEASUREMENT INFORMATION
Start
SCL
ACK or Read Cycle
SDA
30%
tRESET
50%
RESET
tREC
tW
OUTn
50%
tRESET
Figure 1. Reset Timing
SDA
tBUF
tHD;STA
tr
tSP
tf
tLOW
SCL
tSU;DAT
tHD;STA
P
tHD;DAT
S
tHIGH
tSU;DAT
tSU;STO
Sr
P
Figure 2. Definition of Timing
Protocol
Bit 7
MSB
(A7)
Start
Condition
(S)
tSU;STA
tLOW
Bit 6
(A6)
tHIGH
Bit 7
(D1)
Bit 8
(D0)
Acknowledge
(A)
Stop
Condition
(P)
1/fSCL
SCL
tr
tf
tBUF
SDA
tHD;STA
tSU;DAT
tHD;DAT
tVD;DAT
tVD;ACK
tSU;STO
NOTE: Rise and fall times refer to VIL and VIH.
Figure 3. I2C Bus Timing
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
VCC
RL
Pulse
Generator
VI
DUT
RT
VCC
Open
GND
VO
CL
NOTE: RL = Load resistance for SDA and SCL; should be >1 kΩ at 3-mA or lower current.
CL = Load capacitance; includes jig and probe capacitance.
RT = Termination resistance; should be equal to the output impedance (ZO) of the pulse generator.
Figure 4. Test Circuit for Switching Characteristics
8
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
APPLICATION INFORMATION
Functional Description
Device Address
Following a Start condition, the bus master must output the address of the slave it is accessing.
Regular I2C Bus Slave Address
The I2C bus slave address of the TLC59108 is shown in Figure 5. To conserve power, no internal pullup resistors
are incorporated on the hardware-selectable address pins, and they must be pulled high or low. For buffer
management purpose, a set of sector information data should be stored.
Slave Address
1
0
Fixed
0
A3
A2
A1
A0 R/W
Hardware
Selectable
Figure 5. Slave Address
The last bit of the address byte defines the operation to be performed. When set to logic 1, a read operation is
selected. When set to logic 0, a write operation is selected.
LED All Call I2C Bus Address
• Default power-up value (ALLCALLADR register): 90h or 1001 000
• Programmable through I2C bus (volatile programming)
• At power-up, LED All Call I2C bus address is enabled. TLC59108 sends an ACK when 90h (R/W = 0) or 91h
(R/W = 1) is sent by the master.
See LED All Call I2C Bus Address Register (ALLCALLADR) for more detail.
NOTE:
The default LED All Call I2C bus address (90h or 1001 000) must not be used as a
regular I2C bus slave address since this address is enabled at power-up. All the
TLC59108s on the I2C bus will acknowledge the address if sent by the I2C bus master
LED Sub Call I2C Bus Address
• Three different I2C bus address can be used
• Default power-up values:
– SUBADR1 register: 92h or 1001 001
– SUBADR2 register: 94h or 1001 010
– SUBADR3 register: 98h or 1001 100
• Programmable through I2C bus (volatile programming)
• At power-up, Sub Call I2C bus address is disabled. TLC59108 does not send an ACK when 92h (R/W = 0) or
93h (R/W = 1) or 94h (R/W = 0) or 95h (R/W = 1) or 98h (R/W = 0) or 99h (R/W = 1) is sent by the master.
See I2C Bus Subaddress Registers 1 to 3 (SUBADR1 to SUBADR3) for more detail.
NOTE:
The default LED Sub Call I2C bus address may be used as a regular I2C bus slave
address as long as they are disabled.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Software Reset I2C Bus Address
The address shown in Figure 6 is used when a reset of the TLC59108 needs to be performed by the master. The
software reset address (SWRST Call) must be used with R/W = 0. If R/W = 1, the TLC59108 does not
acknowledge the SWRST. See Software Reset for more detail.
1
0
0
1
0
1
1
R/W
Figure 6. Software Reset Address
NOTE:
2
The Software Reset I C bus address is reserved address and cannot be use as
regular I2C bus slave address or as an LED All Call or LED Sub Call address.
Control Register
Following the successful acknowledgement of the slave address, LED All Call address or LED Sub Call address,
the bus master will send a byte to the TLC59108, which will be stored in the Control register. The lowest 5 bits
are used as a pointer to determine which register will be accessed (D[4:0]). The highest 3 bits are used as
Auto-Increment flag and Auto-Increment options (AI[2:0]).
Auto-Increment
Flag
Register Address
AI2 AI1 AI0 D4
D3
D2
D1
D0
Auto-Increment
Options
Figure 7. Control Register
When the Auto-Increment flag is set (AI2 = logic 1), the five low order bits of the Control register are
automatically incremented after a read or write. This allows the user to program the registers sequentially. Four
different types of Auto-Increment are possible, depending on AI1 and AI0 values.
Table 1. Auto-Increment Options
AI2
AI1
AI0
0
0
0
DESCRIPTION
No auto-increment
1
0
0
Auto-increment for all registers. D[4:0] roll over to 0 0000 after the last register (1 1011) is
accessed.
1
0
1
Auto-increment for individual brightness registers only. D[4:0] roll over to 0 0010 after the last
register (1 0001) is accessed.
1
1
0
Auto-increment for global control registers only. D[4:0] roll over to 1 0010 after the last register (1
0011) is accessed.
1
1
1
Auto-increment for individual and global control registers only. D[4:0] roll over to 0 0010 after the
last register (1 0011) is accessed.
NOTE:
Other combinations not shown in Table 1. (AI[2:0] = 001, 010 and 011) are reserved
and must not be used for proper device operation.
AI[2:0] = 000 is used when the same register must be accessed several times during a single I2C bus
communication, for example, changes the brightness of a single LED. Data is overwritten each time the register
is accessed during a write operation.
AI[2:0] = 100 is used when all the registers must be sequentially accessed, for example, power-up programming.
AI[2:0] = 101 is used when the four LED drivers must be individually programmed with different values during the
same I2C bus communication, for example, changing color setting to another color setting.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
AI[2:0] = 110 is used when the LED drivers must be globally programmed with different settings during the same
I2C bus communication, for example, global brightness or blinking change.
AI[2:0] = 111 is used when individually and global changes must be performed during the same I2C bus
communication, for example, changing color and global brightness at the same time.
Only the 5 least significant bits D[4:0] are affected by the AI[2:0] bits.
When the Control register is written, the register entry point determined by D[4:0] is the first register that will be
addressed (read or write operation), and can be anywhere between 0 0000 and 1 1011 (as defined in ). When
AI[2] = 1, the Auto-Increment flag is set and the rollover value at which the point where the register increment
stops and goes to the next one is determined by AI[2:0]. See for rollover values. For example, if the Control
register = 1111 0100 (F4h), then the register addressing sequence will be (in hex):
14 → ... → 1B → 00 → ... → 13 → 02 → ... → 13 → 02 → ... as long as the master keeps sending or reading
data.
Driver Output
Constant Current Output
In LED display applications, TLC59108 provides nearly no current variations from channel to channel and from
device to device. While IOUT ≤ 100 mA, the maximum current skew between channels is less than ±3% and less
than ±6% between devices.
Adjusting Output Current
TLC59108 scales up the reference current (Iref) set by the external resistor (Rext) to sink the output current (Iout) at
each output port. The following formulas can be used to calculate the target output current IOUT,target in the
saturation region:
VREXT = 1.26 V × VG
Iref = VREXT/Rext, if another end of the external resistor Rext is connected to ground
IOUT,target = Iref × 15 × 3CM – 1
Where Rext is the resistance of the external resistor connected to the REXT terminal, and VREXT is the voltage of
REXT, which is controlled by the programmable voltage gain (VG), which is defined by the Configuration Code.
The Current Multiplier (CM) determines that the ratio IOUT,target/Iref is 15 or 5. After power on, the default value of
VG is 127/128 = 0.992, and the default value of CM is 1, so that the ratio IOUT,target/Iref = 15. Based on the default
VG and CM.
VREXT = 1.26 V × 127/128 = 1.25 V
IOUT,target = (1.25 V/Rext) × 15
Therefore, the default current is approximately 52 mA at 360 Ω and 26 mA at 720 Ω. The default relationship
after power on between IOUT,target and Rext is shown in Figure 8.
140
IOUT – mA
120
100
80
40
0
0 500
1000
1500
2000
2500
3000
3500 4000
Rext – W
Figure 8. IOUT,target vs Rext
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Register Descriptions
Table 2 describes the registers in the TLC59108.
Table 2. Register Descriptions
REGISTER
NUMBER
(HEX)
(1)
12
NAME
ACCESS (1) DESCRIPTION
00
MODE1
R/W
Mode 1
01
MODE2
R/W
Mode 2
02
PWM0
R/W
Brightness control LED0
03
PWM1
R/W
Brightness control LED1
04
PWM2
R/W
Brightness control LED2
05
PWM3
R/W
Brightness control LED3
06
PWM4
R/W
Brightness control LED4
07
PWM5
R/W
Brightness control LED5
08
PWM6
R/W
Brightness control LED6
09
PWM7
R/W
Brightness control LED7
0A
GRPPWM
R/W
Group duty cycle control
0B
GRPFREQ
R/W
Group frequency
0C
LEDOUT0
R/W
LED output state 0
0D
LEDOUT1
R/W
LED output state 1
0E
SUBADR1
R/W
I2C bus subaddress 1
0F
SUBADR2
R/W
I2C bus subaddress 2
10
SUBADR3
R/W
I2C bus subaddress 3
11
ALLCALLADR
R/W
LED All Call I2C bus address
12
IREF
R/W
IREF configuration
13
EFLAG
R
Error flag
R = read, W = write
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Mode Register 1 (MODE1)
Table 3 describes Mode Register 1.
Table 3. MODE1 – Mode Register 1 (Address 00h) Bit Description
BIT
7
6
5
4
3
2
(1)
(2)
(3)
(4)
SYMBOL
ACCESS (1)
AI2
R
AI1
R
AI0
R
SLEEP
R/W
SUB1
R/W
SUB2
R/W
1
SUB3
R/W
0
ALLCALL
R/W
VALUE
DESCRIPTION
0 (2)
Register Auto-Increment disabled
1
Register Auto-Increment enabled
0 (2)
Auto-Increment bit 1 = 0
1
Auto-Increment bit 1 = 1
0 (2)
Auto-Increment bit 0 = 0
1
Auto-Increment bit 0 = 1
0
Normal mode (3)
1 (2)
Low power mode. Oscillator off (4).
(2)
Device does not respond to I2C bus subaddress 1.
1
Device responds to I2C bus subaddress 1.
(2)
Device does not respond to I2C bus subaddress 2.
1
Device responds to I2C bus subaddress 2.
(2)
Device does not respond to I2C bus subaddress 3.
1
Device responds to I2C bus subaddress 3.
0
Device does not respond to LED All Call I2C bus address.
(2)
Device responds to LED All Call I2C bus address.
0
0
0
1
R = read, W = write
Default value
Requires 500 µs maximum for the oscillator to be up and running once SLEEP bit has been set to logic 1. Timings on LED outputs are
not guaranteed if PWMx, GRPPWM, or GRPFREQ registers are accessed within the 100 µs window.
No blinking or dimming is possible when the oscillator is off.
Mode Register 2 (MODE2)
Table 4 describes Mode Register 2.
Table 4. MODE2 – Mode Register 2 (Address 01h) Bit Description
BIT
7
SYMBOL
EFCLR
6
5
2:0
(1)
(2)
(3)
R/W
R
DMBLNK
4
3
ACCESS (1)
R/W
R
OCH
R/W
R
VALUE
DESCRIPTION
(2)
Enable error status flag
1
Clear error status flag
0
0 (2)
Reserved
(2)
Group control = dimming
1
Group control = blinking
0
0 (2)
Reserved
0 (2)
Outputs change on Stop command (3)
1
000 (2)
Outputs change on ACK
Reserved
R = read, W = write
Default value
Change of the outputs at the Stop command allows synchronizing outputs of more than one TLC59108. Applicable to registers from 02h
(PWM0) to 0Dh (LEDOUT) only.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Brightness Control Registers 0 to 7 (PWM0 to PWM7)
Table 6 describes Brightness Control Registers 0 to 7.
Table 5. PWM0 to PWM7 – PWM Registers 0 to 7 (Address 02h to 09h) Bit Description
ADDRESS
REGISTER
BIT
SYMBOL
ACCESS (1)
VALUE
02h
PWM0
7:0
IDC0[7:0]
R/W
0000 0000 (2)
PWM0 individual duty cycle
(2)
PWM1 individual duty cycle
(1)
(2)
DESCRIPTION
03h
PWM1
7:0
IDC1[7:0]
R/W
0000 0000
04h
PWM2
7:0
IDC2[7:0]
R/W
0000 0000 (2)
PWM2 individual duty cycle
05h
PWM3
7:0
IDC3[7:0]
R/W
0000 0000 (2)
PWM3 individual duty cycle
06h
PWM4
7:0
IDC4[7:0]
R/W
0000 0000 (2)
PWM4 individual duty cycle
(2)
PWM5 individual duty cycle
07h
PWM5
7:0
IDC5[7:0]
R/W
0000 0000
08h
PWM6
7:0
IDC6[7:0]
R/W
0000 0000 (2)
PWM6 individual duty cycle
09h
PWM7
7:0
IDC7[7:0]
R/W
0000 0000 (2)
PWM7 individual duty cycle
R = read, W = write
Default value
A 97-kHz fixed frequency signal is used for each output. Duty cycle is controlled through 256 linear steps from
00h (0% duty cycle = LED output off) to FFh (99.6% duty cycle = LED output at maximum brightness). Applicable
to LED outputs programmed with LDRx = 10 or 11 (LEDOUT0 and LEDOUT1 registers).
Duty cycle = IDCn[7:0] / 256
Group Duty Cycle Control Register (GRPPWM)
Table 6 describes the Group Duty Cycle Control Register.
Table 6. GRPPWM – Group Brightness Control Register (Address 0Ah) Bit Description
ADDRESS
REGISTER
BIT
SYMBOL
ACCESS (1)
VALUE
0Ah
GRPPWM
7:0
GDC0[7:0]
R/W
1111 1111 (2)
(1)
(2)
DESCRIPTION
GRPPWM register
R = read, W = write
Default value
When the DMBLNK bit (MODE2 register) is programmed with logic 0, a 190-Hz fixed-frequency signal is
superimposed with the 97-kHz individual brightness control signal. GRPPWM is then used as a global brightness
control, allowing the LED outputs to be dimmed with the same value. The value in GRPFREQ is then a Don't
care.
General brightness for the eight outputs is controlled through 256 linear steps from 00h (0% duty cycle = LED
output off) to FFh (99.6% duty cycle = maximum brightness). Applicable to LED outputs programmed with
LDRx = 11 (LEDOUT0 and LEDOUT1 registers).
When DMBLNK bit is programmed with logic 1, the GRPPWM and GRPFREQ registers define a global blinking
pattern, where GRPFREQ defines the blinking period (from 24 Hz to 10.73 s) and GRPPWM defines the duty
cycle (ON/OFF ratio in %).
Duty cycle = GDC0[7:0] / 256
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Group Frequency Register (GRPFREQ)
Table 7 describes the Group Frequency Register.
Table 7. GRPFREQ – Group Frequency Register (Address 0Bh) Bit Description
ADDRESS
REGISTER
BIT
SYMBOL
ACCESS (1)
VALUE
0Bh
GRPFREQ
7:0
GFRQ[7:0]
R/W
0000 0000 (2)
(1)
(2)
DESCRIPTION
GRPFREQ register
R = read, W = write
Default value
GRPFREQ is used to program the global blinking period when the DMBLNK bit (MODE2 register) is equal to 1.
Value in this register is a Don't care when DMBLNK = 0. Applicable to LED output programmed with LDRx = 11
(LEDOUT0 and LEDOUT1 registers).
Blinking period is controlled through 256 linear steps from 00h (41 ms, frequency 24 Hz) to FFh (10.73 s).
Global blinking period (seconds) = (GFRQ[7:0] + 1) / 24
LED Driver Output State Registers (LEDOUT0, LEDOUT1)
Table 8 describes LED Driver Output State Registers 0 and 1.
Table 8. LEDOUT0 and LEDOUT1 – LED Driver Output State Registers (Address 0Ch and 0Dh) Bit
Description
ADDRESS
0Ch
0Dh
(1)
(2)
REGISTER
LEDOUT0
LEDOUT1
BIT
SYMBOL
ACCESS (1)
VALUE
7:6
LDR3[1:0]
R/W
00 (2)
LED3 output state control
5:4
LDR2[1:0]
R/W
00 (2)
LED2 output state control
(2)
LED1 output state control
DESCRIPTION
3:2
LDR1[1:0]
R/W
00
1:0
LDR0[1:0]
R/W
00 (2)
LED0 output state control
7:6
LDR7[1:0]
R/W
00 (2)
LED7 output state control
5:4
LDR6[1:0]
R/W
00 (2)
LED6 output state control
(2)
LED5 output state control
LED4 output state control
3:2
LDR5[1:0]
R/W
00
1:0
LDR4[1:0]
R/W
00 (2)
R = read, W = write
Default value
LDRx = 00: LED driver x is off (default power-up state).
LDRx = 01: LED driver x is fully on (individual brightness and group dimming/blinking not controlled).
LDRx = 10: LED driver x is individual brightness can be controlled through its PWMx register.
LDRx = 11: LED driver x is individual brightness and group dimming/blinking can be controlled through its PWMx
register and the GRPPWM registers.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
I2C Bus Subaddress Registers 1 to 3 (SUBADR1 to SUBADR3)
Table 9 describes I2C Bus Subaddress Registers 1 to 3.
Table 9. SUBADR1 to SUBADR3 – I2C Bus Subaddress Registers 1 to 3 (Address 0Eh to 10h) Bit
Description
ADDRESS
0Eh
REGISTER
SUBADR1
0Fh
SUBADR2
BIT
SYMBOL
SUBADR3
100
(2)
A1[7:5]
R
4:1
A1[4:1]
R/W
1001 (2)
0
A1[0]
R
0 (2)
7:5
A2[7:1]
R
4:1
A2[4:1]
R/W
A2[0]
100
R
A3[7:1]
R
4:1
A3[4:1]
R/W
A3[0]
R
Reserved
I2C bus subaddress 2
Reserved
(2)
Reserved
1100 (2)
0
I2C bus subaddress 1
Reserved
(2)
(2)
100
DESCRIPTION
Reserved
1010 (2)
0
7:5
0
(1)
(2)
VALUE
7:5
0
10h
ACCESS (1)
(2)
I2C bus subaddress 3
Reserved
R = read, W = write
Default value
Subaddresses are programmable through the I2C bus. Default power-up values are 92h, 94h, 98h. The
TLC59108 does not acknowledge these addresses immediately after power-up (the corresponding SUBx bit in
MODE1 register is equal to 0).
Once subaddresses have been programmed to valid values, the SUBx bits (MODE1 register) must be set to 1 to
allows the device to acknowledge these addresses.
Only the 7 MSBs representing the I2C bus subaddress are valid. The LSB in SUBADRx register is a read-only bit
(0).
When SUBx is set to 1, the corresponding I2C bus subaddress can be used during either an I2C bus read or write
sequence.
LED All Call I2C Bus Address Register (ALLCALLADR)
Table 10 describes the LED All Call I2C Bus Address Register.
Table 10. ALLCALLADR – LED All Call I2C Bus Address Register (Address 11h) Bit Description
ADDRESS
11h
(1)
(2)
REGISTER
ALLCALLADR
BIT
SYMBOL
ACCESS (1)
VALUE
100
(2)
7:5
AC[7:5]
R
4:1
AC[4:1]
R/W
1000 (2)
0
AC[0]
R
0 (2)
DESCRIPTION
Reserved
All Call I2C bus address register
Reserved
R = read, W = write
Default value
The LED All Call I2C bus address allows all the TLC59108 devices in the bus to be programmed at the same
time (ALLCALL bit in register MODE1 must be equal to 1, which is the power-up default state). This address is
programmable through the I2C bus and can be used during either an I2C bus read or write sequence. The
register address can also be programmed as a Sub Call.
Only the 7 MSBs representing the All Call I2C bus address are valid. The LSB in ALLCALLADR register is a
read-only bit (0).
If ALLCALL bit = 0, the device does not acknowledge the address programmed in register ALLCALLADR.
Output Gain Control Register (IREF)
Table 11 describes the Output Gain Control Register.
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Table 11. IREF – Output Gain Control Register (Address 12h) Bit Description
ADDRESS
11h
(1)
(2)
REGISTER
ALLCALLADR
BIT
SYMBOL
ACCESS (1)
VALUE
(2)
7
CM
R/W
1
6
HC
R/W
1 (2)
5:0
CC[5:0]
R/W
11 1111 (2)
DESCRIPTION
High/low current multiplier
Subcurrent
Current multiplier
R = read, W = write
Default value
IREF determines the voltage gain (VG), which affects the voltage at the REXT terminal and indirectly the reference
current (IREF) flowing through the external resistor at terminal REXT. Bit 0 is the Current Multiplier (CM) bit, which
determines the ratio IOUT,target/Iref. Each combination of VG and CM sets a Current Gain (CG).
• VG: the relationship between {HC,CC[0:5]} and the voltage gain is calculated as shown below:
VG = (1 + HC) × (1 + D/64) / 4
D = CC0 × 25 + CC1 × 24 + CC2 × 23 + CC3 × 22 + CC4 × 21 + CC5 × 20
Where HC is 1 or 0, and D is the binary value of CC[0:5]. So, the VG could be regarded as a floating-point
number with 1-bit exponent HC and 6-bit mantissa CC[0:5]. {HC,CC[0:5]} divides the programmable voltage
gain VG into 128 steps and two sub-bands:
Low voltage sub-band (HC = 0): VG = 1/4 to 127/256, linearly divided into 64 steps
High voltage sub-band (HC = 1): VG = 1/2 to 127/128, linearly divided into 64 steps
• CM: In addition to determining the ratio IOUT,target/Iref, CM limits the output current range.
High Current Multiplier (CM = 1): IOUT,target/Iref = 15, suitable for output current range IOUT = 10 mA to 120 mA.
Low Current Multiplier (CM = 0): IOUT,target/Iref = 5, suitable for output current range IOUT = 5 mA to 40 mA
• CG: The total Current Gain is defined as the following.
VREXT = 1.26 V × VG
Iref = VREXT/Rext, if the external resistor, Rext, is connected to ground.
IOUT,target = Iref × 15 × 3CM – 1 = 1.26 V/Rext × VG × 15 × 3CM – 1 = (1.26 V/Rext × 15) × CG
CG = VG × 3CM – 1
Therefore, CG = (1/12) to (127/128), and it is divided into 256 steps. If CG = 127/128 = 0.992, the
IOUT,target-Rext.
Examples
• IREF Code {CM, HC, CC[0:5]} = {1,1,111111}
VG = 127/128 = 0.992 and CG = VG × 30 = VG = 0.992
• IREF Code {CM, HC, CC[0:5]} = {1,1,000000}
VG = (1 + 1) × (1 + 0/64)/4 = 1/2 = 0.5, and CG = 0.5
• IREF Code {CM, HC, CC[0:5]} = {0,0,000000}
VG = (1 + 0) × (1 + 0/64)/4 = 1/4, and CG = (1/4) × 3–1 = 1/12
After power on, the default value of the Configuration Code {CM, HC, CC[0:5]} is {1,1,111111}. Therefore,
VG = CG = 0.992. The relationship between the Configuration Code and the Current Gain is shown in Figure 9.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
1.00
CM = 0 (Low Current Multiplier)
Current Gain (CG)
0.75
HC = 1 (High
Voltage SubBand)
0.50
HC = 0 (Low
Voltage SubBand)
HC = 0 (Low
Voltage SubBand)
HC = 1 (High
Voltage SubBand)
0.25
CM = 1 (High Current Multiplier)
0.00
Configuration Code (CM, HC, CC[0:5]) in Binary Format
Figure 9. Current Gain vs Configuration Code
Error Flags Registers (EFLAG)
Table 12 describes the Error Flags Register.
Table 12. EFLAG – Error Flags Register (Address 13h) Bit Description
ADDRESS
REGISTER
BIT
SYMBOL
ACCESS (1)
VALUE
13h
EFLAG
7:0
EFLAG[7:0]
R
1111 1111 (2)
(1)
(2)
18
DESCRIPTION
Error flag status by channel
R = read, W = write
Default value
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Open-Circuit Detection
The TLC59108 LED open-circuit detection compares the effective current level Iout with the open load detection
threshold current IOUT, Th. If IOUT is below the threshold IOUT, Th the TLC59108 detects an open load condition. This
error status can be read out as an error flag through the EFLAG register.
For open-circuit error detection, a channel must be on.
Table 13. Open-Circuit Detection
STATE OF OUTPUT PORT
CONDITION OF OUTPUT
CURRENT
ERROR STATUS CODE
MEANING
Off
On
(1)
IOUT = 0 mA
0
Detection not possible
IOUT < IOUT,Th (1)
0
Open circuit
IOUT ≥ IOUT,Th (1)
Channel n error status bit 1
Normal
IOUT,Th = 0.5 × IOUT,target (typical)
Overtemperature Detection and Shutdown
The TLC59108 LED is equipped with a global overtemperature sensor and eight individual channel-selective
overtemperature sensors.
• When the global sensor reaches the trip temperature, all output channels are shutdown, and the error status
is stored in the internal Error Status register of every channel. After shutdown, the channels automatically
restart after cooling down, if the control signal (output latch) remains on. The stored error status is not reset
after cooling down and can be read out as the error status code in the EFLAG register.
• When one of the channel-specific sensors reaches trip temperature, only the affected output channel is shut
down, and the error status is stored only in the internal Error Status register of the affected channel. After
shutdown, the channel automatically restarts after cooling down, if the control signal (output latch) remains
on. The stored error status is not reset after cooling down and can be read out as error status code in the
EFLAG register.
For channel-specific overtemperature error detection, a channel must be on.
The error flags of open-circuit and overtemperature are ORed to set the EFLAG register.
The error status code due to overtemperature is reset when the host writes 1 to bit 7 of the MODE2 register. The
host must write 0 to bit 7 of the MODE2 register to enable the overtemperature error flag.
Table 14. Overtemperature Detection (1)
(1)
STATE OF OUTPUT PORT
CONDITION
ERROR STATUS CODE
On
On → all channels Off
Tj < Tj,trip global
1
MEANING
Normal
Tj > Tj,trip global
All error status bits = 0
Global overtemperature
On
On → Off
Tj < Tj,trip channel n
1
Normal
Tj > Tj,trip channel n
Channel n error status bit = 0
Channel n overtemperature
The global shutdown threshold temperature is approximately 170°C.
Power-On Reset
When power is applied to VCC, an internal power-on reset holds the TLC59108 in a reset condition until VCC
reaches VPOR. At this point, the reset condition is released and the TLC59108 registers, and I2C bus state
machine are initialized to their default states (all zeroes), causing all the channels to be deselected. Thereafter,
VCC must be lowered below 0.2 V to reset the device.
External Reset
A reset can be accomplished by holding the RESET pin low for a minimum of tW. The TLC59108 registers and
I2C state machine are held in their default states until the RESET input is again high.
This input requires a pullup resistor to VCC if no active connection is used.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Software Reset
The Software Reset Call (SWRST Call) allows all the devices in the I2C bus to be reset to the power-up state
value through a specific I2C bus command. To be performed correctly, the I2C bus must be functional and there
must be no device hanging the bus.
The SWRST Call function is defined as the following:
1. A Start command is sent by the I2C bus master.
2. The reserved SWRST I2C bus address 1101 011 with the R/W bit set to 0 (write) is sent by the I2C bus
master.
3. The TLC59108 device(s) acknowledge(s) after seeing the SWRST Call address 1101 0110 (96h) only. If the
R/W bit is set to 1 (read), no acknowledge is returned to the I2C bus master.
4. Once the SWRST Call address has been sent and acknowledged, the master sends two bytes with two
specific values (SWRST data byte 1 and byte 2):
a. Byte1 = A5h: the TLC59108 acknowledges this value only. If byte 1 is not equal to A5h, the TLC59108
does not acknowledge it.
b. Byte 2 = 5Ah: the TLC59108 acknowledges this value only. If byte 2 is not equal to 5Ah, the TLC59108
does not acknowledge it.
If more than two bytes of data are sent, the TLC59108 does not acknowledge any more.
5. Once the correct two bytes (SWRST data byte 1 and byte 2 only) have been sent and correctly
acknowledged, the master sends a Stop command to end the SWRST Call. The TLC59108 then resets to
the default value (power-up value) and is ready to be addressed again within the specified bus free time
(tBUF).
The I2C bus master may interpret a non-acknowledge from the TLC59108 (at any time) as a SWRST Call Abort.
The TLC59108 does not initiate a reset of its registers. This happens only when the format of the Start Call
sequence is not correct.
Individual Brightness Control With Group Dimming/Blinking
A 97-kHz fixed-frequency signal with programmable duty cycle (8 bits, 256 steps) is used to control the individual
brightness for each LED.
On top of this signal, one of the following signals can be superimposed (this signal can be applied to the four
LED outputs):
• A lower 190-Hz fixed-frequency signal with programmable duty cycle (8 bits, 256 steps) provides a global
brightness control.
• A programmable frequency signal from 24 Hz to 1/10.73 s (8 bits, 256 steps) provides a global blinking
control.
20
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
6
7
8
6
7
8
9
5
5
10
3
4
3
4
1
2
1
2
512
510
511
509
507
508
11
12
9
10
8
6
7
5
4
3
2
1
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
N × 40 ns
with N = 0 to 255
(PWM register)
M × 256 × 2 × 40 ns
with M = 0 to 255
(GRPPWM register)
256 × 40 ns = 10.24 µs
(97.6 kHz)
Group Dimming Signal
256 × 2 × 256 × 40 ns = 5.24 ms (190.7 Hz)
Resulting Brightness + Group Dimming Signal
NOTE: Minimum pulse width for LEDn brightness control is 40 ns.
Minimum pulse width for group dimming is 20.48 µs.
When M = 1 (GRPPWM register value), the resulting LEDn Brightness Control + Group Dimming signal has two
pulses of the LED Brightness Control signal (pulse width = n × 40 ns, with n defined in the PWMx register).
This resulting Brightness + Group Dimming signal shows a resulting control signal with n = 4 (8 pulses).
Figure 10. Brightness and Group Dimming Signals
Characteristics of the I2C Bus
The I2C bus is for two-way two-line communication between different devices or modules. The two lines are a
serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a
pullup resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus
is not busy.
Bit Transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the high
period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see
Figure 11).
SDA
SCL
Data Line
Stable;
Data Valid
Change
of Data
Allowed
Figure 11. Bit Transfer
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
21
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Start and Stop Conditions
Both data and clock lines remain high when the bus is not busy. A high-to-low transition of the data line while the
clock is high is defined as the Start condition (S). A low-to-high transition of the data line while the clock is high is
defined as the Stop condition (P) (see Figure 12).
SDA
SCL
S
P
Start Condition
Stop Condition
Figure 12. Start and Stop Conditions
System Configuration
A device generating a message is a transmitter; a device receiving is the receiver. The device that controls the
message is the master and the devices which are controlled by the master are the slaves (see Figure 13).
SDA
SCL
Master
Transmitter/
Receiver
Slave
Receiver
Slave
Transmitter/
Receiver
Master
Transmitter
Master
Transmitter/
Receiver
2
I C Bus
Multiplexer
Slave
Figure 13. System Configuration
Acknowledge
The number of data bytes transferred between the Start and the Stop conditions from transmitter to receiver is
not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a high level put on
the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse.
A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a
master must generate an acknowledge after the reception of each byte that has been clocked out of the slave
transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so
that the SDA line is stable low during the high period of the acknowledge related clock pulse; set-up time and
hold time must be taken into account.
A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last
byte that has been clocked out of the slave. In this event, the transmitter must leave the data line high to enable
the master to generate a Stop condition.
22
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
S
Start
Condition
Clock Pulse for
Acknowledgment
Figure 14. Acknowledge/Not Acknowledge on I2C Bus
Slave Address
Control Register
S A6 A5 A4 A3 A2 A1 A0 0
Start Condition
X X
A
X D4 D3 D2 D1 D0 A
R/W
ACK From Slave
A
ACK From Slave
P
Stop Condition
Auto-Increment Options
Auto-Increment Flag
ACK From Slave
Figure 15. Write to a Specific Register
Slave Address
Control Register
S A6 A5 A4 A3 A2 A1 A0 0
Start Condition
A
1
0
0
0
0
0
MODE2 Register
MODE1 Register
0
0
R/W
A
A
ACK From Slave
A
ACK From Slave
MODE1 Register Selection
Auto-Increment On All Registers (see Note A)
Auto-Increment On
ACK From Slave
SUBADR3 Register
ALLCALLADR Register
A
ACK From Slave
A.
A
ACK From Slave
P
Stop Condition
See Table 2 for register definitions.
Figure 16. Write to All Registers Using Auto-Increment
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
23
TLC59108
SLDS156 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com
Slave Address
Control Register
S A6 A5 A4 A3 A2 A1 A0 0
Start Condition
A
1
0
1
0
0
0
PWM1 Register
PWM0 Register
1
0
A
A
ACK From Slave
R/W
A
ACK From Slave
PWM0 Register Selection
Auto-Increment On Brightness Registers Only
Auto-Increment On
ACK From Slave
PWM4 Register
PWM5 Register
PWM0 Register
A
ACK From Slave
PWMx Register
A
A
A
ACK From Slave
ACK From Slave
ACK From Slave
P
Stop Condition
Figure 17. Multiple Writes to Individual Brightness Registers Using Auto-Increment
Slave Address
Control Register
S A6 A5 A4 A3 A2 A1 A0 0
Start Condition
A
0
1
0
0
0
0
R/W
Slave Address
0
Data From MODE1 Register
A Sr A6 A5 A4 A3 A2 A1 A0 1
0
ACK From Slave
A
A
R/W ACK From Slave
ACK From Master
MODE1 Register Selection
Auto-Increment On All Registers
Auto-Increment On
ACK From Slave
Data From MODE2 Register
Data From PWM0 Register
A
Data From ALLCALLADR Register
A
ACK From Master
ACK From Master
Data From MODE1 Register
A
ACK From Master
A
ACK From Master
Data From Last Read Byte
A
P
ACK From Master
Stop Condition
Figure 18. Read All Registers Auto-Increment
24
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
TLC59108
www.ti.com .................................................................................................................................................................................................. SLDS156 – MARCH 2009
Slave Address
Sequence A
New LED All Call I2C Address
(see Note B)
Control Register
S A6 A5 A4 A3 A2 A1 A0 0
Start Condition
A
X X
X
1
1
0
1
1
A
1
0
0
1
ACK From Slave
R/W
0
1
1
X
A
ACK From Slave
P
Stop Condition
ALLCALLADR Register Selection
Auto-Increment Options
Auto-Increment Flag
ACK From Slave
2
LED All Call I C Address
Sequence B
S 1
0
0
1
1
0
Start Condition
1
The 16 LEDs are on at ACK (see Note C)
LEDOUT0 Register (LED3 to 0 Fully On)
Control Register
0
A
X X
X
1
0
1
0
R/W
0
A
0
0
1
1
ACK From the
Four Slaves
0
1
0
1
A
ACK From the
Four Slaves
P
Stop Condition
LEDOUT0 Register Selection
ACK From Slave
A.
In this example, several TLC59108 devices are used, and the same Sequence A is sent to each of them.
B.
The ALLCALL bit in the MODE1 register is equal to 1 for this example.
C.
The OCH bit in the MODE2 register is equal to 1 for this example.
Figure 19. LED All Call I2C Bus Address Programming and LED All Call Sequence
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
25
PACKAGE OPTION ADDENDUM
www.ti.com
29-Jan-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLC59108IPWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLC59108IRGYR
ACTIVE
VQFN
RGY
20
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Dec-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TLC59108IPWR
TSSOP
PW
20
2000
330.0
16.4
6.95
7.1
1.6
8.0
16.0
Q1
TLC59108IRGYR
VQFN
RGY
20
3000
180.0
12.4
3.8
4.8
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Dec-2009
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLC59108IPWR
TLC59108IRGYR
TSSOP
PW
20
2000
346.0
346.0
33.0
VQFN
RGY
20
3000
190.5
212.7
31.8
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated