S101S15V/S101S16V/S201S15V/S201S16V SIP Type SSR with Built-in Snubber Circuit S101S15V/S101S16V S201S15V/S201S16V ■ Outline Dimensions 1. High radiation resin mold package I T : MAX. 3A rms 2. Isolation voltage between input and output Viso : 3 000 Vrms 3. Built-in zero-cross circuit ( S101S16V/ S201S16V) 4. Built-in snubber circuit 5. Recognized by UL, file No. E94758 Approved by CSA, file No. LR63705 B Parameter Forward current Reverse current RMS ON-state current B 4.2MAX. + - 4 - 1.1 ± 0.2 3 For 200V lines S201S15V S201S16V Symbol 100V line 200V line 0.6 ± 0.1 (2.54) Internal connection diagram S101S15V/S201S15V ( Ta = 25˚C ) Ratings 4 (1.4) ❈ May not be externally connected Operating frequency dI T /dt f 40 45 to 65 A/µ s HZ Operating temperature Storage temperature T opr T stg - 20 to + 80 - 30 to + 100 ˚C ˚C Isolation voltage Soldering temperature V iso T sol 3.0 260 kV rms ˚C S101S16V/S201S16V Zero-cross circuit Unit mA V A rms A V one cycle surge current Repetitive peak OFFstate voltage Critical rate of rise of ON-state current 2 (5.08) (7.62) IF 50 6 VR I T 3 ( Tc<=100˚C) I surge 30 V DRM 400 600 *1 Peak *3 A 1 ■ Absolute Maximum Ratings *2 19.6 ± 0.2 (36.0) S201S15V 3A265VAC S201S16V ❈ 4 - 1.25 ± 0.3 4 - 0.8 ± 0.2 For 100V lines S101S15V S101S16V 5.5 ± 0.2 5.0 ± 0.3 A Model No, φ 3.2 ± 0.2 S101S15V 3A125VAC S101S16V ■ Model Line-ups Output 3.2 ± 0.2 16.4 ± 0.3 Common to Pin No.1 1. Air conditioners 2. OA equipment Input Common to Pin No.1 18.5 ± 0.2 ■ Applications No built-in zero-cross circuit Built-in zero-cross circuit ( Unit : mm ) 11.2MIN. ■ Features 1 1 2 3 4 2 3 4 Output ( Triac T2 ) Output ( Triac T1 ) Input ( + ) Input ( - ) 1 2 1 2 3 4 3 4 Output ( Triac T2 ) Output ( Triac T1 ) Input ( + ) Input ( - ) *1 60H Z sine wave, Tj = 25˚C *2 AC 60Hz for 1 minute, 40 to 60% RH Isolation voltage measuring method: ( 1 ) Dielectric withstand tester, with zero-cross circuit shall be used. ( 2 ) The waveform of applied voltage shall be sine wave. ( 3 ) It shall be applied voltage between input and output. ( Input and output shall be short-circuited respectively) *3 For 10 seconds “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.” S101S15V/S101S16V/S201S15V/S201S16V ■ Electrical Characteristics Parameter Forward voltage Reverse current Symbol VF IR MIN. - TYP. 1.2 - MAX. 1.4 10-4 Unit V A - - 1.5 V rms S101S15V/16V I OP S201S15V/16V S101S15V/16V Open circuit I leak leak current S201S15V/16V Critical rate of rise of OFF-state voltage dV/dt Commutation critical rate of rise (dV/dt ) c of OFF-state voltage S101S15V/S201S15V Minimum trigI FT ger current S101S16V/S201S16V Condition I F = 20mA V R = 3V Resistance load, I F = 20mA, I T = 1.5A rms V OUT = 120V rms V OUT = 240V rms V OUT = 120V rms V OUT = 240V rms V D = 2/3V DRM T j = 125˚C, VD= 400V, dI T /d t = -1.5A/ms V D = 12V, R L = 30 Ω V D = 6V, R L = 30 Ω ON-state voltage VT - - 50 mA rms 30 - 5 10 - 4 - - V/µ s - - 15 mA Isolation resistance R ISO DC500V, R H = 40 to 60% 1010 - - Ω V OX I F = 15mA ton AC50H Z toff R th (j-c) R th (j-a) AC50H Z - 6 45 35 35 1 10 10 - Minimum operating current Output Transfer characteristics Zero-cross voltage Turn-on time S101S16V S201S16V S101S15V/S201S15V S101S16V/S201S16V Turn-off time Thermal resistance Between junction and case Thermal resistance Between junction and ambient ( 1 ) With heat sink ( Al 100 x 100 x t 2mm ) ( 2 ) With heat sink ( Al 50 x 50 x t 2mm ) 5 Note ) With the Al heat sink set up vertically, Al plate install it as shown in the figure Torque : 4kg•cm SSR Apply thermal conductive silicone grease 4 on the heat sink mounting plate.forcibly cooling shall not be carried out. 5mm RMS ON-state current I T ( A rms ) Fig. 1 RMS ON-state Current vs. Ambient Temperature 3 (2) (1) 2 Without heat sink 1 0 - 20 0 25 50 75 80 100 Ambient temperature T a ( ˚C ) 125 - Fig. 2 RMS ON-state Current vs. Case Temperature 5 RMS ON-state current I T ( A rms ) Input ( Ta = 25˚C ) 4 3 2 1 0 - 20 60 70 80 90 100 110 120 125 130 Case temperature T c ( ˚C ) mA rms V/µ s V ms ms ˚C/W ˚C/W S101S15V/S101S16V/S201S15V/S201S16V Fig. 5 Forward Current vs. Forward Voltage Fig. 3 Forward Current vs. Ambient Temperature 60 200 100 Forward current I F ( mA ) Forward current I F ( mA ) 50 40 30 20 10 20 25˚C 0˚C 10 5 1 0 50 Ambient temperature T 80 a 0 100 Maximum ON-state power dissipation 50 40 30 20 10 12 T a = 25˚C 4 3 2 1 0 1 2 3 4 5 RMS on-state current I T ( A rms ) 6 Fig. 7-b Minimum Trigger Current vs. Ambient Temperature ( Typical Value) ( S101S16V/S201S16V) 12 Minimum trigger current I FT ( mA ) Minimum trigger current I FT ( mA ) 8 6 4 2 100 3.0 V D = 6V RL = 30Ω 0 25 50 75 Ambient temperature T a ( ˚C ) 2.5 5 V D = 12V - 20 2.0 6 100 Fig. 7-a Minimum Trigger Current vs. Ambient Temperature ( Typical Value ) ( S101S15V/S201S15V ) 10 1.5 Fig. 6 Maximum ON-state Power Dissipation vs. RMS ON-state Current ( Typical Value) (W) f= 60H z Tj = 25˚Cstart 10 Power-on cycle ( times ) 1.0 Forward voltage V F ( V ) 60 1 0.5 ( ˚C ) Fig. 5 Surge Current vs. Power-on cycle Surge current I surge ( A ) T a = 75˚C 50˚C 2 0 - 20 0 50 125 RL = 30Ω 10 8 6 4 2 - 20 0 25 50 75 100 Ambient temperature T a ( ˚C ) 125 S101S15V/S101S16V/S201S15V/S201S16V T a = 25˚C 5 4 3 2 1 0 0 100 Supply voltage ( V rms ) Fig. 8-b Open Circuit Leak Current vs. Supply Voltage ( Typical Value ) ( S201S15V, S201S16V ) Open circuit leak current I leak ( mA rms ) Open circuit leak current I leak ( mA rms ) Fig. 8-a Open Circuit Leak Current vs. Supply Voltage ( Typical Value) ( S101S15V, S101S16V) 160 ● Please refer to the chapter “ Precautions for Use.” T a = 25˚C 5 4 3 2 1 0 0 200 Supply voltage ( V rms ) 320