CXP85324A/85332A/85340A CMOS 8-bit Single Chip Microcomputer Description The CXP85324A/85332A/85340A are a highly integrated microcomputers composed of a 8-bit CPU, ROM, RAM, and I/O ports. These chips feature many other high-performance circuits in a single-chip CMOS design, including an A/D converter, serial interface, timer/counter, time-base timer, on-screen display function, I2C bus interface, PWM output, remote control reception circuit, HSYNC counter, power supply frequency counter, and watchdog timer. Futhermore, the CXP85324A/85332A/85340A series provides power-on reset and sleep functions which enable to lower power consumption. 64 pin SDIP (PIastic) 64 pin QFP (PIastic) Structure Silicon gate CMOS IC Features • A wide instruction set (213 instructions) which covers various types of data – 16-bit operation/multiplication and division/Boolean bit operation instructions • Minimum instruction cycle 1µs at 4MHz (4MHz version) 0.5µs at 8MHz (8MHz version) • Incorporated ROM capacity 24K bytes (CXP85324A) 32K bytes (CXP85332A) 40K bytes (CXP85340A) • Incorporated RAM capacity 576 bytes • Peripheral functions – A/D converter 8-bit, 4-channel successive approximation method (Conversion time of 40µs at 4MHz and 8MHz) – Serial interface 8-bit clock sync type, 1 channel – Timer 8-bit timer 8-bit timer/counter 19-bit time-base timer – On screen display (OSD) function 12 × 18 dots, 256 character types, 15 character colors, 12lines of 21 characters, black frame output/half blanking, shadow, background color on full screen/half blanking, double scanning, jitter elimination circuit – I2C bus interface – PWM output 14 bits, 1 channel 8 bits, 8 channels – Remote control reception circuit 8-bit pulse measurement circuit, 6-state FIFO – HSYNC counter – Power supply frequency counter – Watchdog timer • Interruption 14 factors, 14 vectors, multi-interruption possible • Standby mode SLEEP • Package 64-pin plastic SDIP/QFP • Piggyback/evaluator CXP85300A 64-pin ceramic PSDIP/PQFP CXP85390 64-pin ceramic PSDIP (accommodates custom font) Purchase of Sony's I2C components conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specifications as defined by Philips. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E93X37B86 HSYNC COUNTER AC TIMER A/D CONVERTER I2C BUS INTERFACE UNIT ACI AN0 to AN3 SCL0 SCL1 SDA0 SDA1 REMOCON 8BIT TIMER 1 FIFO 8BIT TIMER/COUNTER 0 SERIAL INTERFACE UNIT HSI RMC EC TO SI SO SCK ON SCREEN DISPLAY 2 2 INT2 INT1 INTERRUPT CONTROLLER INT0 14BIT PWM WATCH DOG TIMER PWM XLC EXLC R G B I YS YM HSYNC VSYNC 8 BIT PWM 8CH ROM 24K/32K/40K SPC700 CPU CORE PWM0 to PWM7 VSS VDD RST MP EXTAL XTAL PRESCALER/ TIME BASE TIMER RAM 576 BYTES CLOCK GENERATOR/ SYSTEM CONTROL PF0 to PF7 PE6 to PE7 PE0 to PE5 PD0 to PD7 PC0 to PC7 PA0 to PA7 PB0 to PB7 PORT A PORT B PORT C PORT D PORT E –2– PORT F Block Diagram CXP85324A/85332A/85340A CXP85324A/85332A/85340A Pin Assignment (Top View) 64-pin SDIP HSYNC/PA7 1 64 VDD VSYNC/PA6 2 63 NC PA5 3 62 VSS PA4 4 61 MP PA3 5 60 PF0/PWM0 PA2 6 59 PF1/PWM1 PA1 7 58 PF2/PWM2 PA0 8 57 PF3/PWM3 PB7 9 56 PF4/PWM4/SCL0 PB6 10 55 PF5/PWM5/SCL1 PB5 11 54 PF6/PWM6/SDA0 PB4 12 53 PF7/PWM7/SDA1 PB3 13 52 YM PB2 14 51 YS PB1 15 50 I PB0 16 49 B PC7 17 48 G PC6 18 47 R PC5 19 46 EXLC PC4 20 45 XLC PC3 21 44 PE0/INT0 PC2 22 43 PE1/INT1 PC1 23 42 AN0/PE2 PC0 24 41 AN1/PE3 EC/PD7 25 40 AN2/PE4 RMC/PD6 26 39 AN3/PE5 ACI/PD5 27 38 PE6/PWM HSI/PD4 28 37 PE7/TO SI/PD3 29 36 RST SO/PD2 30 35 EXTAL SCK/PD1 31 34 XTAL 32 33 PD0/INT2 VSS Note) 1. NC (Pin 63) is always connected to VDD. 2. Vss (Pins 32 and 62) are both connected to GND. 3. MP (Pin 61) is always connected to GND. –3– CXP85324A/85332A/85340A PF2/PWM2 PF1/PWM1 PF0/PWM0 MP VDD NC PA7/HSYNC VSS PA5 PA6/VSYNC PA3 PA4 PA2 Pin Assignment (Top View) 64-pin QFP 64 63 62 61 60 59 58 57 56 55 54 53 52 1 51 PF3/PWM3 PA0 2 50 PF4/PWM4/SCL0 PB7 3 49 PF5/PWM5/SCL1 PB6 4 48 PF6/PWM6/SDA0 PB5 PA1 5 47 PF7/PWM7/SDA1 PB4 6 46 YM PB3 7 45 YS PB2 8 44 I PB1 9 43 B PB0 10 42 G PC7 11 41 R PC6 12 40 EXLC PC5 13 39 XLC 14 38 PE0/INT0 PE1/INT1 PC4 15 37 PC2 16 36 AN0/PE2 PC1 17 35 AN1/PE3 PC0 18 34 AN2/PE4 19 33 AN3/PE5 TO/PE7 PWM/PE6 RST EXTAL XTAL VSS INT2/PD0 SCK/PD1 SI/PD3 SO/PD2 ACI/PD5 20 21 22 23 24 25 26 27 28 29 30 31 32 HSI/PD4 EC/PD7 RMC/PD6 PC3 Note) 1. NC (Pin 56) is always connected to VDD. 2. Vss (Pins 26 and 58) are both connected to GND. 3. MP (Pin 55) is always connected to GND. –4– CXP85324A/85332A/85340A Pin Description Symbol I/O Description PA0 to PA5 I/O PA6/VSYNC I/O/Input (Port A) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) OSD display vertical synchronization signal input pin. PA7/HSYNC I/O/Input OSD display horizontal synchronization signal input pin. PB0 to PB7 I/O (Port B) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) PC0 to PC7 I/O (Port C) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) PD0/INT2 I/O/Input PD1/SCK I/O/I/O PD2/SO I/O/Output PD3/SI I/O/Input PD4/HSI I/O/Input PD5/ACI I/O/Input PD6/RMC I/O/Input Remote control reception circuit input pin. PD7/EC I/O/Input External event input pin timer/counter. PE0/INT0 PE1/INT1 Input/Input Input pin for external interruption request. Active when falling edge. (2 pins) PE2/AN0 to PE5/AN3 Input/Input PE6/PWM Output/Output PE7/TO Output/Output PF0/PWM0 to PF3/PWM3 Output/Output PF4/PWM4/ SCL0 PF5/PWM5/ SCL1 Output/Output/ I/O PF6/PWM6/ SDA0 PF7/PWM7/ SDA1 Output/Output/ I/O R, G, B, I, YS, YM Output Input pin for external interruption request. Active when falling edge. (Port D) 8-bit I/O port. I/O can be set in a unit of single bits. 12mA sink current drive possible. (8 pins) (Port E) 8-bit port. Lower 6 bits are for inputs; upper 2 bits are for outputs. (8 pins) Serial clock I/O pin. Serial data output pin. Serial data input pin. HSYNC counter input pin. Power supply frequency counter input pin. Analog input pin for A/D converter. (4 pins) 14-bit PWM output pin. (CMOS output) Timer/counter rectangular wave output pin. (Port F) 8-bit output port. Large current (12mA) N-ch open drain output. Lower 4 bits are mid-voltage drive (12V); upper 4 bits are 5V drive. (8 pins) 8-bit PWM output pin. (8 pins) I2C bus interface transfer clock I/O pin. (2 pins) I2C bus interface transfer data I/O pin. (2 pins) OSD display 6-bit output pin. (6 pins) –5– CXP85324A/85332A/85340A Symbol I/O Description EXLC Input XLC Output EXTAL Input XTAL Output RST I/O System reset pin for active at low level. This pin becomes I/O pin, and outputs low level at the power on with power-on reset function executed. (Mask option) MP Input Test mode input pin. Always connect to GND. OSD display clock oscillation I/O pin. Oscillation frequency is determined by the external L and C. Crystal connection pin for system clock oscillation. When using an external clock, input to EXTAL pin and leave XTAL pin open. NC NC. Under normal operation, connect to VDD. VDD Positive supply voltage pin. Vss GND. Both Vss pins should be connected to common GND. –6– CXP85324A/85332A/85340A Input/Output Circuit Formats for Pins Pin Circuit format Port A Port B Port C PA0 to PA5 PB0 to PB7 PC0 to PC7 When reset AAAAA AAAAA AAAAA AAAAA AA AA AA AA Ports A, B, C data Ports A, B, C direction “0” when reset IP Data bus RD (Ports A, B, C) 22 pins Port A AAAA AAAA AAAA Port A direction “0” when reset PA6/VSYNC PA7/HSYNC Input protection circuit AA AA AA AA Port A data IP Data bus RD (Port A) Schmitt input VSYNC HSYNC Hi-Z Hi-Z AAAA AAAA Input multiplexer 2 pins “0” when reset Port D PD0/INT2 PD3/SI PD4/HSI PD5/ACI AAAA AAAA AAAA Port D data Port D direction “0” when reset PD6/RMC PD7/EC AA AA AA AA ∗ Schmitt input Data bus RD (Port D) IP ∗ Large current 12mA INT2, SI, HSI, ACI, RMC, EC 6 pins –7– Hi-Z CXP85324A/85332A/85340A Pin Circuit format When reset Port D AA AA AA AA SCK or SO Output enable ∗ AAAA AAAA PD1/SCK PD2/SO Port D data Large current source 12mA IP Port D direction “0” when reset Hi-Z Schmitt input Data bus RD (Port D) ∗ Large current 12mA SCK only 2 pins Port E PE0/INT0 PE1/INT1 AAAA AA A AA A AA AAAAA AAAAA Schmitt input (Interrupt circuit) IP 2 pins Port E PE2/AN0 to PE5/AN3 Hi-Z Data bus RD (Port E) Input multiplexer IP Port E function selection “0” when reset 4 pins To A/D converter Hi-Z Data bus RD (Port E) Port E AAAAA AAAAA AAAAA AAAAA AA AA TO, PWM PE6/PWM PE7/TO Port E data “1” when reset Port E function selection “1” when reset 2 pins –8– High level CXP85324A/85332A/85340A Pin Circuit format Port F PF0/PWM0 to PF3/PWM3 When reset PWM AAAAA AAAAA AAAAA Port F data ∗ “1” when reset Port F selection 4 pins Large current 12mA SCL, SDA ∗ I2C output enable AAAAA AAAAA AAAAA AAAAA A Port F data 6 pins EXLC XLC Schmitt input SCL, SDA (I2C circuit) BUS SW To internal I2C pins ∗ Large current 12mA AAAA AAAA AA AA R, G, B, I, YS, YM Output polarity “0” when reset Hi-Z Writing data to output polarity register brings output to active AA A AAA AA AA AA AA EXLC XLC 2 pins Hi-Z IP “1” when reset “0” when reset R G B I YS YM AA PWM Port F function selection 4 pins Hi-Z ∗ 12V voltage drive “0” when reset Port F PF4/PWM4/ SCL0 PF5/PWM5/ SCL1 PF6/PWM6/ SDA0 PF7/PWM7/ SDA1 AA IP IP –9– Oscillator control Oscillation halted OSD display clock CXP85324A/85332A/85340A Pin EXTAL XTAL Circuit format AA A AA A AA AA AA AA When reset • Shows the circuit composition during oscillation. IP EXTAL • Feedback resistor is removed during STOP. (This device does not enter the STOP mode.) Oscillation XTAL 2 pins Pull-up resistor Mask option RST 1 pins Schmitt input OP Low level From power-on reset circuit (Mask option) – 10 – CXP85324A/85332A/85340A Absolute Maximum Ratings (Vss = 0V reference) Item Symbol Ratings Unit V Remarks Supply voltage VDD Input voltage VIN –0.3 to +7.0 –0.3 to +7.0∗1 Output voltage VOUT –0.3 to +7.0∗1 V Mid-voltage drive output voltage VOUTP –0.3 to +15.0 V High level output current IOH –5 mA High level total output current ∑IOH –50 mA Total of all output pins IOL 15 mA Ports excluding large current output (value per pin) IOLC 20 mA Large current output port (value per pin)∗2 Low level total output current ∑IOL 130 mA Total of all output pins Operating temperature Topr –20 to +75 °C Storage temperature Tstg –55 to +150 °C Allowable power dissipation PD 1000 mW SDIP 600 mW QFP V Low level output current PF0 to PF3 pins ∗1 VIN and VOUT should not exceed VDD + 0.3V. ∗2 The large current output port is Port D (PD) and Port F (PF). Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should better take place under the recommended operating conditions. Exceeding those conditions may adversely affect the reliability of the LSI. Recommended Operating Conditions Item Min. Max. Unit 4.5 5.5 V 3.5 5.5 V 2.5 5.5 V Guaranteed operation range for 1/16 frequency dividing mode or SLEEP mode. Guaranteed data hold range for STOP mode.∗1 VIH 0.7VDD VDD V ∗2 VIHS 0.8VDD VDD V ∗3 VIHEX VDD – 0.4 VDD + 0.3 V VIL 0 0.3VDD V EXTAL pin∗4 ∗2 VILS 0 0.2VDD V ∗3 VILEX –0.3 0.4 V EXTAL pin∗4 Operating temperature Topr –20 +75 °C Supply voltage High level input voltage Low level input voltage ∗1 ∗2 ∗3 ∗4 Symbol (Vss = 0V reference) VDD Remarks Guaranteed operation range for 1/2 and 1/4 frequency dividing modes. This device does not enter the STOP mode. PA, PB, PC, PE2 to PE5, SCL0, SCL1, SDA0, SDA1 pins INT2, SCK, SI, HSI, ACI, RMC, EC, INT0, INT1, HSYNC, VSYNC, RST pins. Specifies only during external clock input. – 11 – CXP85324A/85332A/85340A DC Characteristics Item High level output voltage Low level output voltage (Ta = –20 to +75°C, Vss = 0V reference) Symbol VOH VOL IIHE Input current Pin Condition PA to PD, PE6, PE7, VDD = 4.5V, IOH = –0.5mA R, G, B, I, YS, YM VDD = 4.5V, IOH = –1.2mA Min. Typ. Max. Unit 4.0 V 3.5 V PA to PD, PE6, PE7, VDD = 4.5V, IOL = 1.8mA R, G, B, I, YS, YM, PF0 to PF3, RST∗1 VDD = 4.5V, IOL = 3.6mA 0.4 V 0.6 V PD, PF VDD = 4.5V, IOL = 12.0mA 1.5 V PF4 to PF7 (SCL0, SCL1, SDA0, SDA1) VDD = 4.5V, IOL = 3.0mA 0.4 V VDD = 4.5V, IOL = 4.0mA 0.6 V EXTAL IIHL VDD = 5.5V, VIH = 5.5V 0.5 40 µA VDD = 5.5V, VIL = 0.4V –0.5 –40 µA –1.5 –400 µA IILR RST∗2 VDD = 5.5V, VIL = 0.4V I/O leakage current IIZ PA to PE, HSYNC, VSYNC, R, G, B, I, YS, YM, RST∗2 VDD = 5.5V, VI = 0, 5.5V ±10 µA Open drain output leakage current (N-ch Tr off) PF0 to PF3 VDD = 5.5V, VOH = 12.0V 50 µA ILOH PF4 to PF7 VDD = 5.5V, VOH = 5.5V 10 µA SCL0: SCL1 SDA0: SDA1 VDD = 4.5V VSCL0 = VSCL1 = 2.25V VSDA0 = VSDA1 = 2.25V 120 Ω I2C bus switch connection impedance RBS (Output Tr off) 1/2 frequency dividing operation mode VDD = 5.5V 4MHz, 8MHz crystal oscillation (C1 = C2 = 22pF) IDD IDDSL SLEEP mode VDD = 5.5V 4MHz, 8MHz crystal oscillation (C1 = C2 = 22pF) IDDST STOP mode∗6 VDD = 5.5V termination of 4MHz, 8MHz crystal oscillation VDD∗3 Supply current Input capacitance CIN PA to PD, PE0 to PE5, SCL, SDA, EXLC, EXTAL, RST 1MHz clock 0V for non-measurement pins 7∗4 20∗4 mA — 13∗5 30∗5 0.6∗4 3∗4 0.8∗5 3∗5 — — µA 10 20 pF mA ∗1 Specifies RST pin only when the power-on reset circuit is selected with mask option. ∗2 For RST pin, specifies the input current when pull-up resistor is selected, and specifies the leakage current when non-resistor is selected. ∗3 When all output pins open. Specifies only when the OSD oscillation is halted. ∗4 Oscillation clock 4MHz version ∗5 Oscillation clock 8MHz version ∗6 This device does not enter the stop mode. – 12 – CXP85324A/85332A/85340A AC Characteristics (1) Clock timing (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item System System clock frequency fC System clock input pulse width tXL, tXH System clock rise and fall times tCR, tCF tEH, tEL tER, tEF Event count input clock pulse widtth Event count input clock rise and fall times Pin Condition XTAL EXTAL Fig. 1, Fig. 2 EXTAL Fig. 1, Fig. 2 External clock drive EXTAL Fig 1, Fig 2 External clock drive EC Fig. 3 EC Fig. 3 Min. 3.5∗2 7∗3 100∗2 Max. Unit 4.5 9 MHz ns 50∗3 200 tsys + 50∗1 ns ns 20 ms ∗1 tsys indicates three values according to the contents of the clock control register (CLC: 00FEH) upper 2 bits (CPU clock selection). tsys (ns) = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") ∗2 Oscillation clock 4MHz version ∗3 Oscillation clock 8MHz version Fig. 1. Clock timing 1/fc VDD – 0.4V EXTAL 0.4V tXH tCF Fig. 2. Clock applied condition AAAAA AAAAA AAAAA External clock EXTAL XTAL C2 C1 tCR AAAAA AAAAA AAAAA Crystal oscillation Ceramic oscillation EXTAL tXL XTAL OPEN Fig. 3. Event count clock timing 0.8VDD EC 0.2VDD tEH tEF – 13 – tEL tER CXP85324A/85332A/85340A (2) Serial transfer Item (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) System Pin tKCY SCK SCK high and low level widths tKH tKL SCK SI input set-up time (for SCK ↑) tSIK SI SI hold time (for SCK ↑) tKSI SI SCK ↓ → SO delay time tKSO SO SCK cycle time Condition Min. Input mode Max. 1000 ns 8000/fc∗ ns 400 ns 4000/fc' – 50∗ ns SCK input mode 100 ns SCK output mode 200 ns SCK input mode 200 ns SCK output mode 100 ns Output mode SCK input mode SCK output mode SCK input mode 200 ns SCK output mode 100 ns Note) The load of SCK output mode and SO output delay time is 50pF + 1TTL. ∗ The value of fc' varies as shown below depending on the specification of oscillation clock option. 4MHz version: fc' = fc 8MHz version: fc' = fc/2 Fig. 4. Serial transfer timing tKCY tKL tKH 0.8VDD SCK 0.2VDD tSIK tKSI 0.8VDD Input data SI Unit 0.2VDD tKSO 0.8VDD SO Output data 0.2VDD – 14 – CXP85324A/85332A/85340A (3) A/D converter characteristics Item (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Max. Unit Resolution 8 Bits Linearity error ±1 LSB Zero transition voltage VZT∗1 Full-scale transition voltage VFT∗2 Conversion time Sampling time tCONV tSAMP Analog input voltage VIAN Pin Condition Ta = 25°C VDD = 5.0V Vss = 0V Min. Typ. –50 10 70 mV 4910 4970 5030 mV 160/fc' ∗3 12/fc' ∗3 AN0 to AN3 0 µs µs VDD V Fig. 5. Definitions for A/D converter terms Digital conversion value FFH FEH ∗1 VZT: Digital conversion values change between 00H ←→ 01H. ∗2 VFT: Digital conversion values change between 0EH ←→ 0FH. ∗3 The value of fc' varies as follows depending on the specification of oscillation clock option. 4MHz version: fc' = fc 8MHz version: fc' = fc/2 Linearity error 01H 00H VZT VFT Analog input – 15 – CXP85324A/85332A/85340A (4) Interruption, reset input (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol tIH tIL tRSL External interruption high and low level widths Reset input low level width Pin Condition Min. INT0 to INT2 RST Max. Unit 1 µs 8/fc'∗ µs ∗ The value of fc' varies as shown below depending on the specification of oscillation clock option. 4MHz version: fc' = fc 8MHz version: fc' = fc/2 Fig. 6. Interruption input timing tIH tIL 0.8VDD INT0 to INT2 (falling edge) 0.2VDD Fig. 7. RST input timing tRSL RST 0.2VDD (5) Power-on reset Power-on reset∗ (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol tR tOFF Power supply rise time Power supply cutt-off time Pin VDD Condition Power-on reset Min. Max. Unit 0.05 50 ms 1 Repeated power-on reset ms ∗ Specifies only when power-on reset function is selected. Fig. 8. Power-on reset 4.5V VDD 0.2V 0.2V tOFF tR Take care when turning on power. – 16 – CXP85324A/85332A/85340A (6) I2C bus timing (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pin Condition Min. Max. Unit 0 100 kHz SCL clock frequency fSLC SCL Bus-free time before starting transfer tBUF tHD; STA tLOW tHIGH tSU; STA tHD; DAT tSU; DAT tR tF tSU; STO SDA, SCL 4.7 µs SDA, SCL 4.0 µs SCL 4.7 µs SCL 4.0 µs SDA, SCL µs SDA, SCL 4.7 0∗ SDA, SCL 250 ns Hold time for starting transfer Clock low level width Clock high level width Set-up time for repeated transfers Data hold time Data set-up time SDA, SCL rise time SDA, SCL fall time Set-up time for transfer completion µs SDA, SCL 1 µs SDA, SCL 300 ns SDA, SCL 4.7 µs ∗ For the data hold time, the SCL rise time (300ns Max.) is not considered so that 300ns should be exceeded. Fig. 9. I2C bus transfer data timing SDA tBUF tR tHD; STA tF SCL tHD; STA P S tSU; STA tLOW tHD; DAT tHIGH St tSU; DAT tSU; STO P Fig. 10. I2C device recommended circuit I2C device RS I2C device RS RS RS RP RP SDA0 (or SDA1) SCL0 (or SCL1) • A pull-up resistor (Rp) must be connected to SDA0 (or SDA1), and SCL0 (or SCL1). • The SDA0 (or SDA1) and SCL0 (or SCL1) series resistance (Rs = 300Ω or less) can be used to reduce spike noise caused by CRT flashover. – 17 – CXP85324A/85332A/85340A (7) OSD timing (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Pin Symbol Condiiton Min. Max. Unit EXLC XLC Fig. 12 4 7∗1 14∗2 MHz OSD clock frequency fOSC HSYNC pulse width tHWD tVWD HSYNC Fig. 11 1.2 VSYNC Fig. 11 1 HSYNC afterwrite rise and fall times tHCG HSYNC Fig. 11 200 ns VSYNC beforewrite rise and fall times tVCG VSYNC Fig. 11 1.0 µs VSYNC pulse width µs H∗3 ∗1 Oscillation clock 4MHz version ∗2 Oscillation clock 8MHz version ∗3 H indicates 1HSYNC period. Fig. 11. OSD timing tHCG tHWD 0.8VDD HSYNC For OSD I/O polarity register (OPOL: 01FAH) bit 7 at “0” 0.2VDD tVCG tVWD 0.8VDD VSYNC For OSD I/O polarity register (OPOL: 01FAH) bit 6 at “0” 0.2VDD Fig. 12. LC oscillation circuit connection EXLC XLC L C1 R∗1 C2 ∗1 The series resistor for XLC is used to reduce the frequency of occurrence of the undesired radiation. – 18 – CXP85324A/85332A/85340A Appendix Fig. 13. SPC700 Series recommended oscillation circuit AAAAA AAAAA AAAAA AAAAA AAAAA AAAAA (i) EXTAL (ii) EXTAL XTAL XTAL Rd Rd C2 C1 C1 C2 Manufacturer MURATA MFG CO., LTD. Model fc (MHz) CSA4.00MG 4.00 CSA4.19MG 4.19 CSA8.00MTZ 8.00 CST4.00MGW∗1 CST4.19MGW∗1 C1 (pF) C2 (pF) Rd (Ω) Circuit Example (i) 30 30 0∗2 4.00 (ii) 4.19 CST8.00MTW∗1 8.00 4.00 RIVER ELETEC CO., LTD. HC-49/U03 4.19 12 12 0∗2 (i) 27 27 0∗2 (i) 8.00 4.00 KINSEKI LTD. HC-49/U(-S) 4.19 8.00 ∗1 These models have the on-chip grounding capacitors (C1 and C2). ∗2 The series resistor for XTAL can reduce the effect of the noise caused by the electrostatic discharge. Mask Option Table Content Item Reset pin pull-up resistor Non-existent Existent Power-on reset circuit Non-existent Existent 4MHz 8MHz Oscillation clock – 19 – CXP85324A/85332A/85340A Fig. 14. Characteristics curves IDD vs. VDD (fc = 8MHz, Ta = 25°C, Typical) IDD vs. VDD (fc = 4MHz, Ta = 25°C, Typical) 15 15 1 2 1 4 1 frequency mode 4 1 frequency 16 mode 1 1 2 frequency mode 10 frequency mode frequency mode 1 frequency mode 16 IDD – Supply current [mA] IDD – Supply current [mA] 10 SLEEP mode 1 SLEEP mode 0.1 0.1 2 4 5 3 VDD – Supply voltage [V] 6 2 6 Parameter curve for OSD oscillator L vs. C (Analytically calculated value) IDD vs. fc (VDD = 5V, Ta = 25°C, Typical) 16 3 4 5 VDD – Supply voltage [V] 100 1 frequency 2 mode 14 5.0MHz 10 1 frequency 4 mode 8 6 4 L – Inductance [µH] IDD – Supply current [mA] 12 6.5MHz 10 1 frequency 16 mode 13.0MHz 2 fOSC = SLEEP mode 1 2π√ LC C = C1 // C2 0 0 1 5 10 fc – System clock [MHz] 50 C1, C2 – Capacitance [pF] – 20 – 100 CXP85324A/85332A/85340A Package Outline Unit: mm + 0.1 0.05 0.25 – 64PIN SDIP (PLASTIC) 750mil + 0.4 57.6 – 0.1 64 19.05 + 0.3 17.1 – 0.1 33 1 0° to 15° 32 3 MIN 0.5 MIN + 0.4 4.75 – 0.1 1.778 0.5 ± 0.1 0.9 ± 0.15 PACKAGE STRUCTURE MOLDING COMPOUND EPOXY / PHENOL RESIN SONY CODE SDIP-64P-01 LEAD TREATMENT SOLDER PLATING EIAJ CODE SDIP064-P-0750-A LEAD MATERIAL 42 ALLOY PACKAGE WEIGHT 8.6g JEDEC CODE 64PIN QFP(PLASTIC) 23.9 ± 0.4 + 0.4 20.0 – 0.1 + 0.1 0.15 – 0.05 51 0.15 64 20 1 16.3 32 + 0.4 14.0 – 0.1 52 17.9 ± 0.4 33 + 0.2 0.1 – 0.05 0.8 ± 0.2 19 + 0.35 2.75 – 0.15 + 0.15 0.4 – 0.1 1.0 ± 0.12 M PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE QFP–64P–L01 LEAD TREATMENT EIAJ CODE ∗ QFP064–P–1420 LEAD MATERIAL SOLDER/PALLADIUM PLATING COPPER /42 ALLOY PACKAGE WEIGHT 1.5g JEDEC CODE – 21 –