CXP82432A/82440A CMOS 8-bit Single Chip Microcomputer Description The CXP82432A/82440A is a CMOS 8-bit single chip microcomputer integrating on a single chip an A/D converter, serial interface, timer/counter, time base timer, capture timer counter, fluorescent display tube controller/driver, remote control reception circuit, CTL duty detection circuit, 14-bit PWM output and high-speed output circuit besides the basic configurations of 8-bit CPU, ROM, RAM, and I/O port. The CXP82432A/82440A also provides sleep/stop function that enables lower power consumption. 100 pin QFP (Plastic) Structure Silicon gate CMOS IC Features • Wide-range instruction system (213 instructions) to cover various types of data —16-bit arithmetic/multiplication and division/boolean bit operation instructions • Minimum instruction cycle 400ns at 10MHz operation (122µs at 32kHz operation) • Incorporated ROM capacity 32K bytes (CXP82432A) 40K bytes (CXP82440A) • Incorporated RAM capacity 1120 bytes (including fluorescent display area) • Peripheral functions — A/D converter 8-bit, 8-channel, successive approximation method (Conversion time of 32µs/10MHz) — Serial interface 8-bit, 8-stage FIFO incorporated (Auto transfer for 1 to 8 bytes), 1 channel 8-bit clock synchronized type, 1 channel — Timers 8-bit timer, 8-bit timer/counter, 19-bit time base timer 16-bit capture timer/counter, 32kHz timer/counter — Fluorescent display tube controller/driver Maximum of 384 segments display possible 1 to 16-digit dynamic display Dimmer function High voltage drive output (40V) Incorporated pull-down resistor (Mask option) Hardware key scan function Maximum of 16 x 8 key matrix compatible — Remote control reception circuit Incorporated noise elimination circuit 8-bit pulse measuring counter, 6-stage FIFO — PWM output circuit 14 bits, 1 channel — CTL duty detection circuit — High-speed output circuit Precision of 800ns at 10MHz, 4 outputs • Interruption 19 factors, 15 vectors, multi-interruption possible • Standby mode SLEEP/STOP • Package 100-pin plastic QFP • Piggyback/evaluation chip CXP82400A 100-pin ceramic QFP Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E94Z15-PP RAM PE7/ADJ PE7/TO PB0/CINT PE1/INT2/EC1 PE0/INT0/EC0 FIFO FIFO 16 BIT CAPTURE TIMER/COUNTER 2 8 BIT TIMER 1 8 BIT TIMER/COUNTER 0 SERIAL INTERFACE UNIT 1 SERIAL INTERFACE UNIT 0 PB1/CS0 PB3/SI0 PB4/SO0 PB2/SCK0 PB6/SI1 PB7/SO1 PB5/SCK1 REMOCON PE4/RMC CTL DUTY DET 24 PD0/S0 to PI7/S23 VFDP FDP CONTROLLER/ DRIVER PE5/CTL PE7/DDO 8 14 BIT PWM GENERATOR 8 T0 to T7 T15/S24 to T8/S31 AVSS A/D CONVERTER 2 2 PE0/EC0/INT0 PE1/EC1/INT1 PE2/INT2 PE3/INT3/NMI 2 2 2 INTERRUPT CONTROLLER AVREF PE6/PWM 8 PA0/AN0 to PA7/AN7 2 CH0 4 CH1 REALTIME PULSE GENERATOR PRESCALER/ TIME BASE TIMER ROM 32K/40K BYTES SPC 700 CPU CORE TEX TX EXTAL XTAL VDD VSS RST 32kHz TIMER/COUNTER RAM 1120 BYTES CLOCK GEN./ SYSTEM CONTROL 8 PB0 to PB6 7 PF0 to PF7 PG0 to PG7 PH0 to PH7 2 8 8 8 8 PI0 to PI7 PE0 to PE5 PE6 to PE7 6 PD0 to PD7 PC0 to PC7 PB7 PA0 to PA7 8 8 PORT F PORT G –2– PG0/RTO0 to PG3/RTO3 PORT A PORT B PORT C PORT D PORT E PORT H PORT I Block Diagram CXP82432A/82440A CXP82432A/82440A T6 T5 T4 T3 T2 T1 T0 VFDP VDD NC Vss PG0/RTO0 PG1/RTO1 PG2/RTO2 PG3/RTO3 PG4 PG5 PG6 PG7 PE0/EC0/INT0 Pin Assignment (Top View) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 T7 2 79 T8/S31 PE3/INT3/NMI 3 78 T9/S30 PE4/RMC 4 77 T10/S29 PE5/CTL 5 76 T11/S28 PE6/PWM 6 75 T12/S27 PE7/TO/DDO/ADJ 7 74 T13/S26 PB0/CINT 8 73 T14/S25 PB1/CS0 9 72 T15/S24 PB2/SCK0 10 71 PI7/S23 PI6/S22 PE1/EC1/INT1 1 PE2/INT2 PB3/SI0 11 70 PB4/SO0 12 69 PI5/S21 PB5/SCK1 13 68 PI4/S20 PB6/SI1 14 67 PI3/S19 PI2/S18 15 66 PC0/KR0 16 65 PI1/S17 PC1/KR1 17 64 PI0/S16 PC2/KR2 18 63 PF7/S15 PC3/KR3 PB7/SO1 19 62 PF6/S14 PC4/KR4 20 61 PF5/S13 PC5/KR5 21 60 PF4/S12 PC6/KR6 22 59 PF3/S11 PC7/KR7 23 58 PF2/S10 PH0 24 57 PF1/S9 PH1 25 56 PF0/S8 PH2 26 55 PD7/S7 PH3 27 54 PD6/S6 PD5/S5 28 53 PH5 29 52 PD4/S4 PH6 30 51 PD3/S3 Note) 1. NC (Pin 90) must be connected to VDD. 2. Vss (Pins 41 and 91) must be connected to GND. –3– PD2/S2 PD1/S1 AVss PD0/S0 AVREF PA7/AN7 TEX PA6/AN6 TX Vss XTAL EXTAL RST PA5/AN5 PA4/AN4 PA3/AN3 PA2/AN2 PA1/AN1 PH7 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 PA0/AN0 PH4 CXP82432A/82440A Pin Description Pin code I/O Functions (Port A) 8-bit I/O port. I/O can be set in single bit units. (8pins) PA0/AN0 to PA7/AN7 I/O/ Analog input PB0/CINT I/O/Input PB1/CS0 I/O/Input PB2/SCK0 I/O/I/O PB3/SI0 I/O/Input PB4/SO0 I/O/Output PB5/SCK1 I/O/I/O PB6/SI1 I/O/Input Serial data input (CH1). PB7/SO1 Output/Output Serial data output (CH1). Analog inputs to A/D converter. (8 pins) Capture input to 16-bit timer/counter. (Port B) 8-bit I/O port. I/O for lower 7 bits can be set in a unit of single bits. Uppermost bit (PB7) is for output only. (8 pins) Chip select input for serial interface (CH0). Serial clock I/O (CH0). Serial data input (CH0). Serial data output (CH0). Serial clock I/O (CH1). PC0/KR0 to PC7/KR7 I/O/Input (Port C) 8-bit I/O port. I/O can Serves as key return inputs when operating be set in a unit of single key scan with FDP segment signal. bits. Capable of driving 12mA sync current. PD0/S0 to PD7/S7 Output/Output (Port D) 8-bit output port. (8 pins) PE0/INT0/ EC0 Input/Input/Input PE1/INT1/ EC1 Input/Input/Input PE2/INT2 Input/Input PE3/INT3/ NMI Input/Input/Input PE4/RMC Input/Input PE5/CTL Input/Input Input for CTL duty direction circuit. PE6/PWM Output/Output 14-bit PWM output. PE7/TO/ DDO/ADJ Output/Output/ Output/Output Output for the 16-bit timer/counter rectangular waves, CTU duty detection, and 32kHz oscillation frequency demultiplication. PF0/S8 to PF7/S15 Output/Output PG0/RTO0 to PG3/RTO3 I/O/Output PG4 to PG7 I/O (Port E) 8-bit port. Lower 6 bits are for inputs; upper 2 bits are for outputs. (8 pins) (Port F) 8-bit output port. (8pins) FDP segment signal outputs. Inputs for external interruption request. (4 pins) External event inputs for timer/counter. (2 pins) Non-maskable interruption request input. Remote control reception circuit input. FDP segment signal outputs. (Port G) Outputs for real-time pulse generator (RTG). 8-bit I/O port. I/O can Functions as high-precision, real-time pulse be set in a unit of single output port. bits. Data for the lower (4 pins) 4 bits are gated with the contents of RTO or OR-gate output. (8 pins) –4– CXP82432A/82440A Pin code I/O Functions PH0 to PH7 I/O (Port H) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) PI0/S16 to PI7/S23 Output/Output (Port I) 8-bit output ports. (8 pins) T8/S31 to T15/S24 Output/Output Outputs for FDP timing (digit) signals/segment signals. T0 to T7 Output FDP timing signal outputs. VFDP FDP segment signal outputs. FDP voltage supply when incorporated resistor is set by mask option. Crystal connectors system clock oscillation. When the clock is supplied externally, input to EXTAL; opposite phase clock should be input to XTAL. EXTAL Input XTAL Output TEX Input TX Output Crystal connectors for 32kHz timer/counter clock oscillation. Set 32kHz crystal oscillator between TEX and TX. For usage as event input, attach clock source to TEX, and open TX. RST Input Low-level active, system reset. NC AVREF NC. Under normal operation, connect to VDD. Input Reference voltage input for A/D converter. AVSS A/D converter GND. VDD Vcc supply. VSS GND. –5– CXP82432A/82440A I/O Circuit Format for Pins Pin When reset Circuit format Port A Port A data PA0/AN0 to PA7/AN7 Port A direction Input multiplexer IP “0” when reset Hi-Z Data bus RD (Port A) Port A input selection Input protection circuit “0” when reset A/D converter 8 pins Port B Port B data PB0/CINT PB1/CS0 PB3/SI0 PB6/SI1 Port B direction IP Hi-Z “0” when reset Schmitt input Data bus RD (Port B) 4 pins CINT CS0 SI0 SI1 Port B SCK OUT Output enable Port B output selection “0” when reset PB2/SCK0 PB5/SCK1 Port B data IP Port B direction “0” when reset Schmitt input Data bus RD (Port B) SCK in 2 pins –6– Hi-Z CXP82432A/82440A Pin When reset Circuit format Port B SO Ouput enable Port B output selection “0” when reset PB4/SO0 Port B data Hi-Z IP Port B direction “0” when reset Data bus RD (Port B) 1 pin Port B Internal reset signal SO AAAA AAAA AAAA Output enable PB7/SO1 ∗ Port B output selection “0” when reset AA High level Port B data “1” when reset ∗ Pull-up transistor approx. 200kΩ Data bus 1 pin RD (Port B) AAAA AAAA AAAA Port C Port C data PC0/KR0 to PC7/KR7 ∗ Port C direction “0” when reset AA AAA IP Hi-Z Data bus RD (Port C) 8 pins ∗ High current drive of 12mA possible Key input signal Port E PE0/EC0/INT0 PE1/EC1/INT1 PE2/INT2 PE3/INT3/NMI PE4/RMC PE4/CTL AA AA AAAA EC0/INT0 EC1/INT1 INT2 INT3/NMI RMC CTL Data bus Schmitt input IP RD (Port E) 6 pins –7– Hi-Z CXP82432A/82440A Pin AAAA AAAA AAAA When reset Circuit format Port E AA AA PWM Port E output selection “0” when reset PE6/PWM Port E data “1” when reset High level Data bus 1 pin RD (Port E) AA AA AA AAAAA AAAAA AAAAA AAAAA AAAAA Port E Output enable 0 1 MPX 2 3 TO DDO ADJ16K∗ ADJ2K∗ PE7/TO/ DDO/ADJ AA AA Port E output selection Port E output selection “00” when reset Port E output selection “0” when reset Port E data “1” when reset Data bus 1 pin AAAA AAAA AAAA AAAA AAAA High level ∗ ADJ signal is a frequency demultiplication output for 32kHz oscillation frequency adjustment. ADJ2 can be used for buzzer output. RD (Port E) Port G RTO data “0” when reset PC0/RTO0 to PG3/RTO3 Port G data Port G direction “0” when reset Data bus 4 pins Port H AAAAA AAAAA AAAAA Port G or Port H data Port G or Port H direction “0” when reset Data bus 12 pins Hi-Z IP RD (Port G) Port G PG4 to PG7 PH0 to PH7 AA AA AA AA RD (Port G or Port H) –8– AA A IP Hi-Z CXP82432A/82440A Pin PD0/S0 to PD7/S7 When reset Circuit format Port D Port F Port I PF0/S8 to PF7/S15 ∗ High voltage drive transistor Segment output data ∗ Output selection control signal (“0” when reset) OP Data for Port D, F, or I PI0/S16 to PI7/S23 “0” when reset Mask option Pull-down resistor Hi-Z or Low level (when PD resistance is added) VFDP Data bus 24 pins RD (Port D, F, or I) ∗ High voltage drive transistor T15/S24 to T8/S31 Segment output data ∗ Output selection control signal (“0” when reset) T0 to T7 OP Mask option Hi-Z or Low level (when PD resistance is added) Pull-down resistor 16 pins EXTAL XTAL VFDP EXTAL IP IP • Diagram shows circuit composition during oscillation. Oscillation • Feedback resistor is removed during stop. XTAL 2 pins TEX TX TEX • Diagram shows circuit composition during oscillation. IP IP Oscillation • When the operation of the oscillation circuit is stopped by the software, the feedback resistor is removed, and TEX and TX become “Low” level and “High” level respectively. TX 2 pins Pull-up resistor RST OP Low level Mask option IP Schmitt input 1 pin –9– CXP82432A/82440A Absolute Maximum Ratings Item Supply voltage Symbol VDD (Vss = 0V reference) Rating Unit –0.3 to +7.0 V V Remarks Input voltage VIN –0.3 to +0.3 –0.3 to +7.0∗1 Output voltage VOUT –0.3 to +7.0∗1 V Display output voltage VOD VDD–40 to VDD+0.3 V IOH –5 mA As P channel transistor is open drain, VDD is reference. All pins excluding outputs∗2 (value per pin) IODH1 –15 mA Display outputs S0 to S23 (value per pin) IODH2 –35 mA Display outputs T0 to T7, and T8/S31 to T15/S24 (value per pin) ∑IOH –40 mA Total for all pins excluding display outputs ∑IODH –100 mA Total for all display outputs IOL 15 mA Port 1 IOLC 20 mA High current Port 1∗3 Low level total output current ∑IOL 100 mA Total for all output pins High level output current High level total output current Low level output current AVss V Operating temperature Topr –20 to +75 °C Storage temperature Tstg –55 to +150 °C 600 mW Allowable power dissipation PD ∗1) VIN and VOUT must not exceed VDD + 0.3V. ∗2) Specifies output current of general-purpose I/O ports. ∗3) The high current drive transistor is the N-CH transistor of Port C (PC). Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should be conducted under the recommended operating conditions. Exceeding these conditions may adversely affect the reliability of the LSI. – 10 – CXP82432A/82440A Recommended Operating Conditions Item Supply voltage High level input voltage Symbol Min. Max. Unit 4.5 5.5 V High-speed mode Guaranteed operation range 3.5 5.5 V Low-speed mode Guaranteed operation range 2.7 5.5 V Guaranteed operation range with TEX clock 2.5 5.5 V VIH 0.7VDD VDD V VIHS 0.8VDD VDD V VDD VIHEX Low level input voltage Operating temperature (Vss = 0V reference) VDD – 0.4 VDD + 0.3 Remarks Guaranteed data hold range during STOP ∗1 V Hysteresis input∗2 EXTAL∗3 ∗1 VIL 0 0.3VDD V VILS 0 0.2VDD V VILEX –0.3 0.4 V Topr –20 +75 °C Hysteresis input∗2 EXTAL∗3 ∗1) Value for each pin of normal input port (PA, PB4, PC, PG, PH). ∗2) Value of the following pins: RST, CINT, CS0, SCK0, SCK1, SI0, SI1, EC0/INT0, EC1/INT1, INT2, INT3/NMI, RMC, CTL. ∗3) Specifies only during external clock input. – 11 – CXP82432A/82440A Electrical Characteristics DC Characteristics Item High level output current Low level output current (Ta = –20 to +75°C, Vss = 0V reference) Symbol VOH VOL Pins PA, PB, PC, PE6, PE7, PG, PH PC IIHE IILE Input current IIHT IILT IILR EXTAL Conditions IOH S24/T15 to S31/T8 T0 to T7 Max. Unit 4.0 V VDD = 4.5V, IOH = –1.2mA 3.5 V VDD = 4.5V, IOL = 1.8mA 0.4 V VDD = 4.5V, IOL = 3.6mA 0.6 V VDD = 4.5V, IOL = 12.0mA 1.5 V VDD = 5.5V, VIH = 5.5V 0.5 40 µA VDD = 5.5V, VIL = 0.4V –0.5 –40 µA VDD = 5.5V, VIH = 5.5V 0.1 10 µA VDD = 5.5V VIL = 0.4V –0.1 –10 µA –1.5 –400 µA S0 to S23 Display output current Typ. VDD = 4.5V, IOH = –0.5mA TEX RST∗1 Min. VDD = 4.5V VOH = VDD – 2.5V Open drain output leakage current ILOL (P-CH Tr off state) S0 to S23 S24/T15 to S31/T8 T0 to T7 VDD = 5.5V VOL = VDD – 35V VFDP = VDD – 35V Pull-down resistance∗2 RL S0 to S23 S24/T15 to S31/T8 T0 to T7 VDD = 5V VFDP = VDD – 35V I/O leakage current IIZ PA to PC VDD = 5.5V PE, PG, PH, VI = 0, 5.5V RST∗1 – 12 – –8 mA –20 mA 60 100 –20 µA 270 kΩ ±10 µA CXP82432A/82440A Item Symbol Pins Conditions Min. Typ. Max. Unit 20 40 mA 35 100 µA 1.2 8 mA 9 30 µA 10 µA 20 pF High speed mode operation (1/2 frequency demultiplier clock) IDD1 VDD = 5.5V, 10MHz crystal oscillation (C1 = C2 = 15pF) VDD = 3V, 32kHz crystal oscillation (C1 = C2 = 47pF) IDD2 Power supply current∗3 Input capacity IDDS1 VDD SLEEP mode VDD = 5.5V, 10MHz crystal oscillation (C1 = C2 = 15pF) IDDS2 VDD = 3V, 32kHz crystal oscillation (C1 = C2 = 47pF) IDDS3 STOP mode VDD = 5.5V, 10MHz crystal oscillation; and termination of 32kHz oscillation CIN Pins other than S0 to S31, T0 to T7, PB7, PE6, AVREF, AVSS, VFDP, VDD, VSS Clock 1MHz 0V for all pins excluding measured pins 10 ∗1) RST specifies the input current when pull-up resistance has been selected; leakage current when no resistance has been selected. PB7 does not specify the leakage current because it’s only for output. ∗2) When incorporated pull-down resistance has been selected through mask option. ∗3) When all pins are open. – 13 – CXP82432A/82440A AC Characteristics (1) Clock timing (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol System clock frequency fC Event count input clock rise time, fall time tXL tXH tCR tCF tEH tEL tER tEF System clock frequency fC Event count input pulse width tTL tTH tTR tTF System clock input pulse width System clock input rise time, fall time Event count input clock pulse width Event count input rise time, fall time Pin Conditions Min. XTAL EXTAL Fig. 1, Fig. 2 EXTAL Fig. 1, Fig. 2 External clock drive EXTAL Fig. 1, Fig. 2 External clock drive EC0, EC1 Fig. 3 EC0, EC1 Fig. 3 TEX TX VDD = 2.7 to 5.5V Fig. 2 (32kHz clock application condition) TEX Fig. 3 TEX Fig. 3 Typ. 1 Max. Unit 10 MHz ns 37.5 200 tsys + 50∗ ns ns 20 ms kHz 32.768 µs 10 20 ms ∗ tsys indicates the three values below according to the upper two bits (CPU clock selection) of the control clock registor (address: 00FEH). tsys (ns)=2000/fc (upper two bits="00"), 4000/fc (upper two bits="01"), 16000/fc (upper two bits="11") Fig. 1. Clock timing 1/fc VDD–0.4V EXTAL 0.4V tXH tCF tXL tCR AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA Fig. 2. Clock application conditions Crystal oscillation Ceramic oscillation EXTAL C1 32kHz clock application condition Crystal oscillation External clock EXTAL XTAL C2 TEX XTAL 74HC04 TX C2 C1 Fig. 3. Event count clock timing 0.8VDD TEX EC0 EC1 0.2VDD tEH tTH tEF tTF – 14 – tEL tTL tER tTR CXP82432A/82440A (2) Serial transfer (CH0) Item (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Condition Pin Min. Max. Unit CS0 ↓ → SCK0 delay time tDCSK SCK0 Chip select transfer mode (SCK0 = output mode) tsys + 200 ns CS0 ↑ → SCK0 float delay time tDCSKF SCK0 Chip select transfer mode (SCK0 = output mode) tsys + 200 ns CS0 ↓ → SO0 delay time tDCSO SO0 Chip select transfer mode tsys + 200 ns CS0 ↑ → SO0 float delay time tDCSOF SO0 Chip select transfer mode tsys + 200 ns CS0 High level width tWHCS CS0 Chip select transfer mode tsys + 200 ns SCK0 cycle time tKCY Input mode 2tsys + 200 ns SCK0 16000/fc ns SCK0 High, Low level width tKH tKL Input mode tsys + 100 ns SCK0 Output mode 8000/fc–50 ns SI0 input set-up time (for SCK0 ↑) tSIK SCK0 input mode 100 ns SI0 SCK0 output mode 200 ns SI0 input hold time (for SCK0 ↑) tKSI tsys + 200 ns SI0 100 ns SCK0 ↓ → SO0 delay time tKSO SO0 Output mode SCK0 input mode SCK0 output mode SCK0 input mode SCK0 output mode tsys + 200 ns 100 ns Note 1) tsys indicates the three values below according to the upper two bits (CPU clock selection) of the control clock registor (address: 00FEH). tsys (ns)=2000/fc (upper two bits="00"), 4000/fc (upper two bits="01"), 16000/fc (upper two bits="11") Note 2) The load condition for the SCK0 output mode, SO0 output delay time is 50pF + 1TTL. – 15 – CXP82432A/82440A Fig. 4. Serial transfer CH0 timing tWHCS CS0 0.8VDD 0.2VDD tKCY tDCSK tKL tDCSKF tKH 0.8VDD 0.8VDD SCK0 0.2VDD tSIK tKSI 0.8VDD SI0 Input data 0.2VDD tDCSO tKSO tDCSOF 0.8VDD SO0 Ouput data 0.2VDD – 16 – CXP82432A/82440A Serial transfer (CH1) Item (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Pin Condition tKCY SCK1 SCK1 High, Low level width tKH tKL SCK1 SI1 input set-up time (for SCK1 ↑) tSIK SI1 SI1 input hold time (for SCK1 ↑) tKSI SI1 SCK1 ↓ → SO1 delay time tKSO SO1 SCK1 cycle time Min. Max. Input mode 1000 ns Ouput mode 16000/fc ns Input mode 400 ns Ouput mode 8000/fc–50 ns SCK1 input mode 100 ns SCK1 ouput mode 200 ns SCK1 input mode 200 ns SCK1 ouput mode 100 ns SCK1 input mode 200 ns SCK1 ouput mode 100 ns Note) The load condition for the SCK1output mode, SO1 output delay time is 50pF + 1TTL. Fig. 5. Serial transfer CH1 timing tKCY tKL tKH 0.8VDD SCK1 0.2VDD tSIK tKSI 0.8VDD Input data SI1 Unit 0.2VDD tKSO 0.8VDD SO1 Output data 0.2VDD – 17 – CXP82432A/82440A (3) A/D converter characteristics (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, AVREF = 4.0 to AVDD, Vss = AVSS = 0V reference) Item Symbol Pin Max. Unit Resolution 8 Bits Linearity error ±3 LSB Ta = 25°C VDD = 5.0V VSS = AVSS = 0V Zero transition voltage VZT∗1 Full-scale transition voltage VFT∗2 Conversion time Sampling time tCONV tSAMP Reference input voltage VREF AVREF Analog input voltage VIAN AN0 to AN7 Min. Typ. –10 10 70 mV 4910 4970 5030 mV 160/fADC∗3 12/fADC∗3 IREF AVREF current Condition Operation mode SLEEP mode STOP mode 32kHz operation mode AVREF IREFS µs µs VDD – 0.5 VDD V 0 AVREF V 1.0 mA 10 µA 0.6 Fig. 6. Definition of A/D converter terms Digital conversion value FFH FEH ∗1) VZT: Value at which the digital transfer value changes from 00H to 01H and vice versa. ∗2) VFT: Value at which the digital transfer value changes from FEH to FFH and vice versa. ∗3) fADC indicates the below values due to ADC operation clock selection (ADCS: Bit 6 of address 00F9H). During PS2 selection, fADC = fc/2 During PS1 selection, fADC = fc Linearity error 01H 00H VFT VZT Analog input – 18 – CXP82432A/82440A (4) Interruption, reset input Item (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Pin Condition External interruption High, Low level width tIH tIL INT0 INT1 INT2 NMI/INT3 Reset input Low level width tRSL RST Min. Max. Unit 1 µs 32/fc µs Fig. 7. Interruption input timing tIH tIL 0.8VDD INT0 INT1 INT2 NMI/INT3 (NMI specifies only for the falling edge) 0.2VDD tIL tIH Fig. 8. RST input timing tRSL RST 0.2VDD (5) Others (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol CLK input High, Low level width tCTH tCTL Pin Condition tsys = 2000/fc CTL Min. Max. tsys + 200 ns Fig. 9. Other timing tCTH tCTL 0.8VDD CTL 0.2VDD – 19 – Unit CXP82432A/82440A Appendix Fig. 10. Recommended oscillation circuit AAAA AAAA AAAA AAAA AAAAA AAAA AAAAA AAAA AAAAA (i) Main clock EXTAL (ii) Main clock EXTAL XTAL Rd C1 (iii) Sub clock EXTAL TEX XTAL XTAL TX Rd C2 Rd C1 C2 C 1 C2 Manufacturer MURATA MFG CO., LTD. Model CSA4.19MG 4.19 CSA8.00MTZ 8.00 CSA10.0MTZ 10.00 CST4.19MGW∗ CST8.00MTW∗ CST10.0MTW∗ RIVER ELETEC CO., LTD fc (MHz) C2 (pF) Rd (Ω) Circuit example (i) 30 30 0 4.19 8.00 (ii) 10.00 4.19 HC-49/U03 8.00 12 12 0 10.00 4.19 KINSEKI LTD. C1 (pF) HC-49/U (-S) P3 8.00 (i) 27 27 0 10.00 20 20 32.768kHz 50 22 (iii) 1M Those marked with an asterisk (∗) signify types with built-in ground capacitance (C1, C2). Mask option table Content Item Reset pin pull-up resistance Non-existent Existent High voltage drive output port pull-down resistance Non-existent Existent – 20 – CXP82432A/82440A Unit: mm 100PIN QFP (PLASTIC) + 0.4 14.0 – 0.01 17.9 ± 0.4 15.8 ± 0.4 + 0.1 0.15 – 0.05 23.9 ± 0.4 + 0.4 20.0 – 0.1 A 0.65 + 0.35 2.75 – 0.15 ±0.12 M (16.3) 0.15 0° to 15° DETAIL A 0.8 ± 0.2 Package Outline PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE QFP-100P-L01 LEAD TREATMENT SOLDER PLATING EIAJ CODE ∗QFP100-P-1420-A LEAD MATERIAL COPPER / 42 ALLOY PACKAGE WEIGHT 1.4g JEDEC CODE – 21 –