CXP864P61 CMOS 8-bit Single Chip Microcomputer Description The CXP864P61 is the CMOS 8-bit single chip microcomputer integrating on a single chip an A/D converter, serial interface, timer/counter, time-base timer, on-screen display function, I2C bus interface, PWM output, remote control reception circuit, HSYNC counter, watchdog timer, 32kHz timer/counter besides the basic configurations of 8-bit CPU, PROM, RAM, I/O ports. The CXP864P61 also provides a sleep function that enables to lower the power consumption. The CXP864P61 is the PROM-incorporated version of the CXP86461 with built-in mask ROM. This provides the additional feature of being able to write directly into the program. Thus, it is most suitable for evaluation use during system development and for small-quantity production. 52 pin SDIP (Plastic) Structure Silicon gate CMOS IC Features • A wide instruction set (213 instructions) which covers various types of data — 16-bit operation/multiplication and division/Boolean bit operation instructions • Minimum instruction cycle 250ns at 16MHz operation (4.5 to 5.5V) 122µs at 32kHz operation (2.7 to 5.5V) • Incorporated PROM 60K bytes • Incorporated RAM 1536 bytes (Excludes VRAM for on-screen display and sprite RAM) • Peripheral functions — A/D converter 8 bits, 6 channels, successive approximation method (Conversion time of 3.25µs at 16 MHz) — Serial interface 8-bit clock sync type, 1 channel — Timer 8-bit timer 8-bit timer/counter 19-bit time-base timer 32kHz timer/counter — On-screen display (OSD) function 12 × 16 dots, 52 character types 15 character colors, 2 lines × 24 characters, frame background 8 colors/ half blanking, background on full screen 15 colors/ half blanking edging/ shadowing/ rounding for every line, background with shadow for every character, double scanning, sprite OSD, 12 × 16 dots, 1 screen, 8 colors for every dot — I2C bus interface — PWM output 8 bits, 8 channels 14 bits, 1 channel — Remote control reception circuit 8-bit pulse measurement counter, 6-stage FIFO — HSYNC counter 2 channels — Watchdog timer • Interruption 13 factors, 13 vectors, multi-interruption possible • Standby mode Sleep • Package 52-pin plastic SDIP Perchase of Sony's I2C components conveys a licence under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specifications as defined by Philips. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E97740A84 HSYNC COUNTER 1 ON SCREEN DISPLAY XLC EXLC R G B I YS YM HSYNC VSYNC HS1 8BIT TIMER 1 TO HSYNC COUNTER 0 8BIT TIMER/ COUNTER 0 EC HS0 SERIAL INTERFACE UNIT FIFO SI SO SCK REMOCON 2 2 I2C BUS INTERFACE UNIT SDA0 RMC INTERRUPT CONTROLLER INT0 INT1 INT2 SDA1 A/D CONVERTER 6CH SCL0 6 SCL1 AN0 to AN5 2 ADJ 6 14BIT PWM RAM 1536 BYTES CLOCK GENERATOR /SYSTEM CONTROL 8BIT PWM 32kHz TIMER/COUNTER WATCHDOG TIMER PRESCALER/ TIME BASE TIMER PROM 60K BYTES SPC700 CPU CORE TEX TX EXTAL XTAL RST MP VDD VSS PWM0 to PWM5 –2– PWM PORT A PORT B PORT D 1 PG7 PF0 to PF7 8 PE0 to PE1 2 PE4 to PE6 PD0 to PD7 8 3 PB0 to PB7 8 PE2 to PE3 PA0 to PA7 8 2 PORT E PORT F PORT G Block Diagram CXP864P61 CXP864P61 Pin Assignment (Top View) 1 52 PF0/PWM0 RMC/PD6 2 51 PF1/PWM1 HS1/PD5 3 50 PF2/PWM2 HS0/PD4 4 49 PF3/PWM3 SI/PD3 5 48 PF4/SCL0 SO/PD2 6 47 PF5/SCL1/PWM4 SCK/PD1 7 46 PF6/SDA0 EC/PD7 INT2/PD0 8 45 PF7/SDA1/PWM5 HSYNC/PA7 9 44 PE0/TO/ADJ VSYNC/PA6 10 43 PE1/PWM RST 11 42 PE2/TEX/INT0 VSS 12 41 PE3/TX XTAL 13 40 VSS EXTAL 14 39 VDD PA5/AN5 15 38 Vpp PA4/AN4 16 37 EXLC PA3/AN3 17 36 XLC PA2/AN2 18 35 PE4/YM PA1/AN1 19 34 PE5/YS PA0/AN0 20 33 PE6/I PB7 21 32 B PB6 22 31 G PB5 23 30 R PB4 24 29 PB0 PB3 25 28 PB1 INT1/PG7 26 27 PB2 Note) 1. Vpp (Pin 38) is left open. 2. Vss (Pins 12 and 40) are both connected to GND. –3– CXP864P61 Pin Description I/O Symbol PA0/AN0 to PA5/AN5 I/O/ Analog input PA6/VSYNC I/O/Input PA7/HSYNC I/O/Input Description (Port A) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) Analog inputs to A/D converter. (6 pins) OSD display vertical sync signal input. OSD display horizontal sync signal input. (Port B) 8-bit I/O port. I/O can be set in a unit of single bits. (8 pins) PB0 to PB7 I/O PD0/INT2 I/O/Input PD1/SCK I/O/I/O PD2/SO I/O/Output PD3/SI I/O/Input PD4/HS0 I/O/Input PD5/HS1 I/O/Input PD6/RMC I/O/Input Remote control reception circuit input. PD7/EC I/O/Input External event input for timer/counter. PE0/TO/ADJ I/O/Output/ Output Rectangular wave output for 8-bit timer/counter. PE1/PWM I/O/Output PE2/TEX/INT0 Input/Input/ Input PE3/TX Input/Output PE4/YM Output/Output PE5/YS Output/Output PE6/I Output/Output B Output G Output R Output PF0/PWM0 to PF3/PWM3 Output/Output PF4/SCL0 Output/I/O PF5/SCL1/ PWM4 Output/I/O/ Output PF6/SDA0 Output/I/O PF7/SDA1/ PWM5 Output/I/O/ Output External interruption request input. Active at the falling edge. (Port D) 8-bit I/O port. I/O can be set in a unit of single bits. Can drive 12mA synk current. (8 pins) (Port E) Bits 0 and 1 are I/O port; I/O can be set in a unit of single bit. Bits 2 and 3 are input port. Bits 4, 5 and 6 are output port. (7 pins) Serial clock I/O. Serial data output. Serial data input. HSYNC counter (CH0) input. HSYNC counter (CH1) input. 32kHz oscillation frequency dividing output. 14-bit PWM output. Connects a crystal for External interruption request input. Active at 32kHz timer/counter clock oscillation. When the falling edge. used as an event counter, input to TEX pin and leave TX pin open. OSD display 6-bit output. (6 pins) (Port F) 8-bit output port. Open drain output of large current (12mA) and N channel. Lower 4 bits are medium drive voltage (12V); upper 4 bits are 5V drive. (8 pins) –4– 8-bit PWM output. (4 pins) I2C bus interface transfer clock I/O. (2 pins) 8-bit PWM output. I2C bus interface transfer data I/O. (2 pins) 8-bit PWM output. CXP864P61 Symbol I/O Description (Port G) 1-bit I/O port. I/O can be set in a unit of single bits. (1 pin) External interruption request input. Active at the falling edge. PG7/INT1 I/O/Input EXTAL Input XTAL Output Connects a crystal for system clock oscillation. When a clock is supplied externally, input to EXTAL pin and input a reversed phase clock to XTAL pin. RST Input System reset; active at Low level. EXLC Input XLC Output OSD display clock oscillation I/O. Oscillation frequency is determined by the external L and C. VDD Positive power supply. Vss GND. Connect two Vss pins to GND. Vpp Positive power supply for incorporated-PROM writing. No connected for normal operation. –5– CXP864P61 Input/Output Circuit Formats for Pins Pin Circuit format When reset Port A Port A data Port A direction PA0/AN0 to PA5/AN5 “0” when reset IP Data bus Input protection circuit RD (Port A) Port A function selection “0” when reset A/D converter Hi-Z Input multiplexer 6 pins Port A Port A data Port A direction PA6/VSYNC PA7/HSYNC "0" when reset Schmitt input Data bus IP Hi-Z RD (Port A) HSYNC, VSYNC Input polarity 2 pins "0" when reset Port B Ports B, G data Port G Ports B, G direction PB0 to PB7 PG7/INT1 “0” when reset Hi-Z Data bus IP RD (Ports B, C, G) 9 pins Schmitt input for PB0, PB1, PB2, and PG7 INT1 Port F PWM0 to PWM3 PF0/PWM0 to PF3/PWM3 Port F function selection ∗ “0” when reset Port F data ∗ 12V drive voltage Large current 12mA “1” when reset 4 pins –6– Hi-Z CXP864P61 Pin Circuit format When reset Port D Port D data PD0/INT2 PD3/SI PD4/HS0 PD5/HS1 PD6/RMC PD7/EC Port D direction ∗ “0” when reset Hi-Z Schmitt input Data bus IP RD (Port D) 6 pins ∗ Large current 12mA INT2, SI, HS0, HS1, RMC, EC Port D SCK, SO SIO output enable Port D data PD1/SCK PD2/SO ∗ Port D direction Hi-Z “0” when reset IP Data bus RD (Port D) ∗ Large current 12mA SCK only 2 pins PD2 is not Schmitt input. Port E Internal reset signal PE0/TO/ADJ Port E data 00 “1” when reset TO ADJ16K∗1 ADJ2K∗1 01 10 11 MPX ∗2 Port E function selection (Upper) Port E function selection (Lower) “00” when reset Port E direction “1” when reset Data bus 1 pin ∗1 ADJ signals are frequency dividing outputs for 32kHz oscillation frequency IP adjustment. ADJ2K provides usage as buzzer output. ∗2 Pull-up resistors approx. 150kΩ RD (Port E) –7– High level (with the resistor of pull-up transister ON when reset) CXP864P61 Pin Circuit format When reset Port E PWM Port E function selection “0” when reset Port E data “1” when reset PE1/PWM High level Port E direction “1” when reset IP Data bus RD (Port E) 1 pin Port E 32kHz oscillation circuit control “1” when reset Schmitt input INT0 Data bus RD (Port E) PE2/TEX/INT0 PE3/TX Data bus RD (Port E) Schmitt input PE2/ TEX/ INT0 2 pins IP Oscillation halted Port input IP Clock input PE3/ TX Port E YM, YS, I Output polarity PE4/YM PE5/YS PE6/I “0” when reset Port E function selection Hi-Z “0” when reset Port E data Writing data to output polarity register and port data register brings output to active. 3 pins –8– CXP864P61 Pin Circuit format Port F When reset SCL, SDA I2C bus enable ∗ PWM4, PWM5 PF4/SCL0 PF5/SCL1/PWM4 PF6/SDA0 PF7/SDA1/PWM5 Port F function selection “0” when reset Hi-Z Port F data Schmitt input “1” when reset SCL, SDA (I2C bus circuit) IP BUS SW ∗ Large current 12mA 4 pins To internal I2C pins (SCL1 for SCL0) R, G, B Output polarity R G B “0” when reset Hi-Z Writing data to output polarity register brings output to active. 3 pins Oscillation control EXLC XLC EXLC 2 pins XLC EXTAL XTAL 2 pins IP IP OSD display clock Oscillation halted IP EXTAL • Diagram shows the circuit composition during oscillation. • Feedback resistor is removed during stop mode. (This device does not enter the stop mode.) XTAL Oscillation Pull-up resistor RST 1 pin AA AA Schmitt input –9– Low level CXP864P61 Absolute Maximum Ratings Item (Vss = 0V reference) Symbol Supply voltage Ratings Unit VDD –0.3 to +7.0 V Vpp V Remarks Input voltage VIN –0.3 to +13.0 –0.3 to +7.0∗1 Output voltage VOUT –0.3 to +7.0∗1 V Medium drive output voltage VOUTP –0.3 to +15.0 V High level output current IOH –5 mA High level total output current ∑IOH –50 mA Total of all output pins IOL 15 mA Ports excluding large current output (value per pin) IOLC 20 mA Large current output ports (value per pin∗2) Low level total output current ∑IOL 130 mA Total of all output pins Operating temperature Topr –10 to +75 °C Storage temperature Tstg –55 to +150 °C Allowable power dissipation PD 400 mW Incorporated PROM V Low level output current SDIP-52P-01 ∗1 VIN and VOUT should not exceed VDD + 0.3 V. ∗2 The large current output port is Port D (PD) and Port F (PF). Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should be conducted under the recommended operating conditions. Exceeding those conditions may adversely affect the reliability of the LSI. Recommended Operating Conditions Item Supply voltage High level input voltage Symbol (Vss = 0V reference) Min. Max. Unit 4.5 5.5 V Guaranteed operation range for 1/2 and 1/4 frequency dividing clock 3.5 5.5 V Guaranteed operation range for 1/16 frequency dividing clock or sleep mode 2.7 5.5 V Guaranteed operation range by TEX clock — — V VIH 0.7VDD VDD V Guaranteed data hold operation range during stop∗5 ∗1 VIHS 0.8VDD VDD V ∗2 V VDD Remarks VIL 0 0.3VDD V EXTAL pin∗3, TEX pin∗4 ∗1 VILS 0 0.2VDD V ∗2 VILEX –0.3 0.4 V EXTAL pin∗3, TEX pin∗4 Operating temperature Topr –10 +75 °C VIHEX Low level input voltage ∗1 ∗2 ∗3 ∗4 ∗5 VDD – 0.4 VDD + 0.3 PA1 to 5, PB3 to 7, PD2, PE0, PE1, PE3, SCL0 to 1, SDA0 to 1 pins VSYNC, HSYNC, INT2, SCK, SI, HS0, HS1, RMC, EC, INT0, INT1, RST, PB0, PB1, PB2 pins Specifies only during external clock input. Specifies only during external event count input. This device does not enter the stop mode. – 10 – CXP864P61 Electrical Characteristics (Ta = –10 to +75°C, Vss = 0V reference) DC characteristics Item High level output voltage Low level output voltage Symbol VOH VOL Pins PA, PB, PD, VDD = 4.5V, IOH = –0.5mA PE0 to PE1, PE4 to PE6, PG7, R, VDD = 4.5V, IOH = –1.2mA G, B Input current IIHT IILT Min. Typ. Max. Unit 4.0 V 3.5 V PA, PB, PD, PE0 to VDD = 4.5V, IOL = 1.8mA PE1, PE4 to PE6, PF0 to PF3, PG7, R, G, B VDD = 4.5V, IOL = 3.6mA 0.4 V 0.6 V PD, PF VDD = 4.5V, IOL = 12.0mA 1.5 V PF4 to PF7 (SCL0, SCL1, SDA0, SDA1) VDD = 4.5V, IOL = 3.0mA 0.4 V VDD = 4.5V, IOL = 4.0mA 0.6 V IIHE IILE Conditions EXTAL TEX VDD = 5.5V, VIH = 5.5V 0.5 40 µA VDD = 5.5V, VIL = 0.4V –0.5 –40 µA VDD = 5.5V, VIH = 5.5V 0.1 10 µA –0.1 –10 µA –1.5 –400 µA ±10 µA VDD = 5.5V, VIL = 0.4V IILR RST∗1 I/O leakage current IIZ PA, PB, PD, PE, PG7, VDD = 5.5V, VI = 0, 5.5V R, G, B, RST∗1 Open drain I/O leakage current (in N-ch Tr off state) ILOH I2C bus switch connection impedance (in output Tr off state) RBS PF0 to PF3 VDD = 5.5V, VOH = 12.0V 50 µA PF4 to PF7 VDD = 5.5V, VOH = 5.5V 10 µA SCL0: SCL1 SDA0: SDA1 VDD = 4.5V VSCL0 = VSCL1 = 2.25V VSDA0 = VSDA1 = 2.25V 120 Ω 25 38 mA 30 90 µA 1.2 2.1 mA 15 38 µA — — µA 1/2 frequency dividing clock VDD = 5.5V, 16MHz crystal oscillation (C1 = C2 = 15pF) IDD1 VDD = 3.3V, 32MHz crystal oscillation (C1 = C2 = 47pF) IDD2 Sleep mode Supply current∗2 IDDS1 IDDS2 IDDS3 VDD VDD = 5.5V, 16MHz crystal oscillation (C1 = C2 = 15pF) VDD = 3.3V, 32MHz crystal oscillation (C1 = C2 = 47pF) Stop mode∗3 VDD = 5.5V, termination of 16MHz and 32MHz oscillation – 11 – — CXP864P61 Item Input capacitance Symbol CIN Pins Conditions PA, PB, PD, PE0 to PE3, R, G, B, PF,PG7, Clock 1MHz 0V for no-measured pins EXTAL, TEX, EXLC, RST Min. Typ. Max. Unit 10 20 pF ∗1 For RST pin, specifies the input current when pull-up resistance is selected, and specifies the leakage current when non-resistor is selected. ∗2 When all output pins are left open. Specifies only when the OSD oscillation is halted. ∗3 This device does not enter the stop mode. – 12 – CXP864P61 AC Characteristics (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) (1) Clock timing Item Symbol System clock frequency fC Event count input clock rise and fall times tXL, tXH tCR, tCF tEH, tEL tER, tEF System clock frequency fC Event count input clock input pulse width tTL, tTH tTR, tTF System clock input pulse width System clock input rise and fall times Event count input clock pulse width Event count input clock rise and fall times Pins Conditions Min. XTAL EXTAL Fig. 1, Fig.2 8 EXTAL Fig. 1, Fig.2 External clock drive 28 EXTAL Fig. 1, Fig.2 External clock drive EC Fig. 3 EC Fig. 3 TEX TX VDD = 2.7 to 5.5 V Fig. 2 (32kHz clock applied conditions) TEX Fig. 3 TEX Fig. 3 Typ. Max Unit 16 MHz ns 200 4tsys∗1 ns ns 20 ms kHz 32.768 µs 10 20 ms ∗1 tsys Indicates three values according to the contents of the clock control register (CLC: 00FEh) upper 2 bits (CPU clock selection). tsys (ns) = 2000/fc (Upper 2 bits = “00”), 4000/fc (Upper 2 bits = “01”), 16000/fc (Upper 2 bits = “11”) Fig. 1. Clock timing 1/fc VDD – 0.4V EXTAL 0.4V tXH tCF tXL tCR AAAAAAAAA AAAA AAAAA AAAA AAAA AAAAAAAAA AAAA Fig.2. Clock applied conditions Crystal oscillation Ceramic oscillation EXTAL C1 External clock EXTAL XTAL C2 32kHz clock applied condition Crystal oscillation TEX XTAL 74HC04 TX C2 C1 Fig. 3. Event count clock timing 0.8VDD TEX EC 0.2VDD tEF tTF tEH tTH – 13 – tEL tTL tER tTR CXP864P61 (2) Serial transfer Item (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Pins tKCY SCK SCK High and Low level width tKH tKL SCK SI input setup time (for SCK ↑) tSIK SI SI hold time (for SCK ↑) tKSI SI SCK ↓ → SO delay time tKSO SO SCK cycle time Conditions Min. Input mode Max. 1000 ns 8000/fc ns 400 ns 4000/fc – 50 ns SCK input mode 100 ns SCK output mode 200 ns SCK input mode 200 ns SCK output mode 100 ns Output mode SCK input mode SCK output mode SCK input mode 200 ns SCK output mode 100 ns Note) The load of SCK output mode and SO output delay time is 50pF + 1TTL. Fig. 4. Serial transfer timing tKCY tKL tKH 0.8VDD SCK 0.2VDD tSIK tKSI 0.8VDD Input data SI Unit 0.2VDD tKSO 0.8VDD SO Output data 0.2VDD – 14 – CXP864P61 (3) A/D converter Item (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Max. Unit Resolution 8 Bits Linearity error ±3 LSB Zero transition voltage VZT∗1 Full-scale transition voltage VFT∗2 Conversion time Sampling time tCONV tSAMP Analog input voltage VIAN Pins Conditions Ta = 25°C VDD = 5.0V Vss = 0V Min. Typ. –10 10 70 mV 4910 4970 5030 mV 26/fADC∗3 6/fADC∗3 AN0 to AN5 0 µs µs VDD V Fig. 5. Definitions for A/D converter terms Digital conversion value FFh FEh ∗1 VZT: Value at which the digital conversion value changes from 00h to 01h and vice versa. ∗2 VFT: Value at which the digital conversion value changes from FEh to FFh and vice versa. ∗3 fADC indicates the below values due to the contents of bit 6 (CKS) of the A/D control register (ADC: 00F6h): Linearity error 01h 00h fADC = fc (CKS = “0”), fc/2 (CKS = “1”) VZT VFT Analog input – 15 – CXP864P61 (4) Interruption, reset input (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pins Conditions Min. Max. Unit External interruption High, Low level width tIH tIL INT0 INT1 INT2 1 µs Reset input Low level width tRSL RST 32/fc µs Fig. 6. Interruption input timing tIH INT0 INT1 INT2 (falling edge) tIL 0.8VDD 0.2VDD Fig. 7. RST input timing tRSL RST 0.2VDD – 16 – CXP864P61 (5) I2C bus timing (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pins Conditions Min. Max. Unit 0 100 kHz SCL clock frequency fSLC SCL Bus-free time before starting transfer tBUF tHD; STA tLOW tHIGH tSU; STA tHD; DAT tSU; DAT tR tF tSU; STO SDA, SCL 4.7 µs SDA, SCL 4.0 µs SCL 4.7 µs SCL 4.0 µs SDA, SCL µs SDA, SCL 4.7 0∗1 SDA, SCL 250 ns Hold time for starting transfer Clock Low level width Clock High level width Setup time for repeated transfers Data hold time Data setup time SDA, SCL rise time SDA, SCL fall time Setup time for transfer completion µs SDA, SCL 1 µs SDA, SCL 300 ns SDA, SCL 4.7 µs ∗1 The data hold time should be 300ns or more because the SCL rise time (300ns Max.) is not included in it. Fig. 8. I2C bus transfer timing SDA tBUF tR tF tHD; STA SCL tHD; STA tSU; STA P S tLOW tHD; DAT tHIGH St tSU; DAT tSU; STO P Fig. 9. I2C bus device recommended circuit I2C bus device RS I2C bus device RS RS R S RP RP SDA0 (or SDA1) SCL0 (or SCL1) • A pull-up resistor (Rp) must be connected to SDA0 (or SDA1) and SCL0 (or SCL1). • The SDA0 (or SDA1) and SCL0 (or SCL1) series resistance (Rs = 300Ω or less) can be reduce the spike noise caused by CRT flashover. – 17 – CXP864P61 (6) OSD timing (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pins Conditions Min. Max Unit 30.4∗1 MHz OSD clock frequency fOSC EXLC XLC Fig. 11 4 HSYNC pulse width tHWD HSYNC Fig. 10 2 HSYNC after-write rise and fall times tHCG HSYNC Fig. 10 200 ns VSYNC before-write rise and fall times tVCG VSYNC Fig. 10 1.0 µs µs ∗1 The maximum value of fosc is specified with the following equation. fosc [max] ≤ fc × 1.9 Fig. 10. OSD timing tHWD tHCG 0.8VDD HSYNC For OSD I/O polarity register (OPOL: 01FEh) bit 7 at “0” 0.2VDD tVCG 0.8VDD VSYNC For OSD I/O polarity register (OPOL: 01FEh) bit 6 at “0” 0.2VDD Fig. 11. LC oscillation circuit connection EXLC XLC R∗1 L C2 C1 ∗1 The series resistor for XLC can reduce the frequency of occurrence of the undesired radiation. – 18 – CXP864P61 Appendix Fig. 12. Recommended oscillation circuit AAAA AAAA AAAAA AAAA AAAA AAAAA AAAA AAAA AAAAA AA A A (i) Main clock EXTAL XTAL (ii) Main clock (iii) Sub clock EXTAL TEX XTAL Rd C1 Rd TX Rd C2 C2 C1 C1 C2 Model Manufacture MURATA MFG CO., LTD. RIVER ELETEC CO., LTD. fc (MHz) CSA10.0MTZ 10.0 CSA12.0MTZ 12.0 CSA16.00MXZ040 CST10.0MTW∗ 16.0 10.0 C1 (pF) C2 (pF) 30 30 5 5 30 30 CST12.0MTW∗ 12.0 CST16.00MXW0C1∗ 16.0 5 5 8.0 18 18 12.0 12 12 16.0 10 10 8.0 10 10 12.0 5 5 16.0 OPEN OPEN 32.768kHz 30 33 HC-49/U03 HC-49/U (-S) KINSEKI LTD. P3 Rd (Ω) Circuit example (i) 0 ∗1 (ii) 330 ∗1 (i) 0 ∗1 120k (iii) ∗ Models with an asterisk have the bull-in ground capacitance (C1, C2). ∗1 The series resistor for XTAL can reduce the effect of the noise caused by the electrostatic discharge. – 19 – CXP864P61 Fig. 13. Characteristic curves IDD vs. VDD IDD vs. fc (fc = 16MHz, Ta = 25°C, Typical) (VDD = 5V, Ta = 25°C, Typical) 100 1/2 dividing mode 20 1/2 dividing mode 1/4 dividing mode 10 IDD – Supply current [mA] IDD – Supply current [mA] 1/16 dividing mode Sleep mode 1 0.1 (100µA) 32kHz mode (instruction) 15 1/4 dividing mode 10 32kHz sleep mode 5 0.01 (10µA) 1/16 dividing mode 2 3 4 5 6 7 VDD – Supply voltage [V] Sleep mode 0 0 5 10 Frequency [MHz] Parameter Curve for OSD Oscillator L vs. C (Analytically calculated value) 100 10 L – Inductance [µH] 1 16MHz 20MHz 24MHz 28MHz 30MHz 1 fOSC = 1 2π√ LC C = C1//C2 0.1 0.01 0 10 20 30 40 50 60 70 C1, C2 – Capacitance [pF] – 20 – 80 90 100 15 CXP864P61 Package Outline Unit: mm + 0.1 .05 0.25 – 0 52PIN SDIP (PLASTIC) 600mil + 0.4 47.0 – 0.1 15.24 + 0.3 13.5 – 0.1 27 52 0° to 15° 26 1 5.0 MIN 2.8 MIN 0.51 MIN 1.778 0.5 ± 0.1 + 0.1 0.9 – 0.05 PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE SDIP-52P-01 LEAD TREATMENT SOLDER PLATING EIAJ CODE SDIP052-P-0600-A LEAD MATERIAL COPPER JEDEC CODE PACKAGE WEIGHT NOTE : PALLADIUM PLATING This product uses S-PdPPF (Sony Spec.-Palladium Pre-Plated Lead Frame). – 21 –