WINBOND W741E260

W741E260
4-BIT FLASH MICROCONTROLLER
Table of Contents-GENERAL DESCRIPTION .............................................................................................................................. 2
FEATURES...................................................................................................................................................... 2
PIN CONFIGURATION.................................................................................................................................... 4
PIN DESCRIPTION ......................................................................................................................................... 5
BLOCK DIAGRAM........................................................................................................................................... 6
FUNCTIONAL DESCRIPTION ........................................................................................................................ 7
ABSOLUTE MAXIMUM RATINGS ................................................................................................................ 37
DC CHARACTERISTICS............................................................................................................................... 37
AC CHARACTERISTICS............................................................................................................................... 39
PAD ASSIGNMENT AND POSITIONS.......................................................................................................... 39
TYPICAL APPLICATION CIRCUIT................................................................................................................ 41
INSTRUCTION SET TABLE .......................................................................................................................... 42
PACKAGE DIMENSIONS.............................................................................................................................. 93
-1-
Publication Release Date: March 1998
Revision A2
W741E260
GENERAL DESCRIPTION
The W741E260 is a high-performance 4-bit microcontroller (µC) that provides an LCD driver and the
flash EEPROM for the program memory. The device contains a 4-bit ALU, two 8-bit timers, two
dividers (for two oscillators) in dual-clock operation, a 32 × 4 LCD driver, and five 4-bit I/O ports
(including 1 output port for LED driving). There are also five interrupt sources and 8-level subroutine
nesting for interrupt applications. The W741E260 operates on very low current and has three power
reduction modes, hold mode and stop mode in single-clock operation and the dual-clock slow
operation, which help to minimize power dissipation.
This chip is available for W741C250 and W741C260 bodies, which can be selected by option code.
The W741E260 is suitable for end product manufacturer engineering testing and earlier samples
before mass production.
FEATURES
• Operating voltage: 2.4V to 5.5V (LCD drive voltage: 3.0V, or 4.5V)
• Crystal/Ceramic oscillator: up to 4 MHz
• RC oscillator: up to 4 MHz
• Dual-clock operation is selected by code option
• Main oscillator
− Crystal or RC oscillation circuit can be selected by code option
− In crystal mode, high-frequency (400 KHz to 4 MHz) or low-frequency (32.768 KHz) oscillation
should be selected by code option
− In RC mode, attention must be paid to the high/low frequency oscillation option, because the LCD
driver frequency and the ROM code emulation time are related to this option.
• Sub-oscillator
− Connect to 32768 Hz crystal only
− Used in dual-clock operation
• Memory
− 2048 x 16-bit program flash EEPROM (including 2K x 4-bit look-up table)
− 128 x 4-bit data RAM (including 16 working registers)
− 32 x 4 LCD data RAM
• 21 input/output pins
−
−
−
−
Ports for input only: 2 ports/8 pins
Input/output ports: 2 ports/8 pins
High sink current for LED driving: 1 port/4 pins
MFP output pin: 1 pin (MFP)
• Power-down mode
− Hold function: no operation (excluding main oscillator and sub-oscillator)
− Stop function: no operation (excluding sub-oscillator)
-2-
W741E260
− Dual-clock slow operation mode: system is operated by the sub-oscillator
(FOSC = Fs and Fm is stopped)
• Five types of interrupts
− Four internal interrupts (Divider0, Divider1, Timer0, Timer1) for W741C260 body;
three internal interrupts (Divider0, Timer0, Timer1) for W741C250 body.
− One external interrupt (RC Port) for W741C260 body;
two external interrupts (RC port and INT pin) for W741C250 body.
• LCD driver output
− 32 segment x 4 common
− Static, 1/2 duty (1/2 bias), 1/3 duty (1/2 or 1/3 bias), 1/4 duty (1/3 bias) driving mode can be
selected
− LCD driver output pins can be used as DC output port by code option
− Clock source can be main oscillator clock in the single-clock operation mode, or sub-oscillator
clock in the dual-clock operation mode; operation mode is selected by code option
• MFP output pin
− Output is software selectable as modulating or nonmodulating frequency
− Works as frequency output specified by Timer 1
• Two built-in 14-bit frequency dividers
− Divider0: the clock source is the output of the main oscillator
− Divider1: the clock source is the output of the sub-oscillator
• Two built-in 8-bit programmable countdown timers
− Timer 0: one of two internal clock frequencies (FOSC/4 or FOSC/1024) can be selected
− Timer 1: includes an auto-reload function and one of two internal clock frequencies (FOSC or
FOSC/64) can be selected, or falling edge of pin RC.0 can be selected (output through MFP pin)
• Built-in 18/14-bit watchdog timer selectable for system reset
− Enable/Disable the watchdog timer can be controlled by command or by option code;
the control source (command or option code) can be determined by another option code
• Powerful instruction set: 118 instructions for W741C260 body
116 instructions for W741C250 body
• 8-level subroutine (include interrupt) nesting
• Up to 1 µS instruction cycle (with 4 MHz operating frequency)
• Packaged in 80-pin QFP
-3-
Publication Release Date: March 1998
Revision A2
W741E260
PIN CONFIGURATION
X
X U
X
/ /
V
R R M I R
I O
I
A A F N E N N T N D N N
1 0 P T S C 1 1 C D C 2
O
X
O
U
T
2
V V
M
D D D D
O
D N H H D D
E C 1 2 1 2
V
D
D
3
S
E
G
3
1
S
E
G
3
0
S
E
G
2
9
S
E
G
2
8
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
RA2
RA3
RB0
RB1
RB2
RB3
RC0
RC1
RC2
RC3
RD0
RD1
RD2
RD3
RE0
RE1
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
N N R R V V D C C
C C E E S P A O O
2 3 S P T M M
A 3 2
C
O
M
1
C
O
M
0
S
E
G
0
S
E
G
1
-4-
S
E
G
2
S
E
G
3
S
E
G
4
S
E
G
5
S
E
G
6
S
E
G
7
S
E
G
8
S
E
G
9
S
E
G
1
0
S N
E C
G
1
1
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
W741E260
PIN DESCRIPTION
SYMBOL
I/O
FUNCTION
XIN1
I
Input pin for main-oscillator.
Connected to crystal or resistor to generate system clock by code option.
XOUT1
O
Output pin for main-oscillator.
Connected to crystal or resistor to generate system clock by code option.
XIN2
I
Input pin for sub-oscillator. Connected to 32.768 KHz crystal.
XOUT2
O
Output pin for sub-oscillator with internal oscillation capacitor. Connected
to 32.768 KHz crystal.
RA0 to RA3
I/O
Input/Output port.
Input/output mode specified by port mode 1 register (PM1).
RB0 to RB3
I/O
Input/Output port.
Input/output mode specified by port mode 2 register (PM2).
RC0 to RC3
I
4-bit port for input only.
Each pin has an independent interrupt capability.
RD0 to RD3
I
4-bit port for input only.
RE0 to RE3
O
Output port only.
This port provides high sink current to drive LEDs.
MFP
O
Output pin only.
This pin can output modulating or nonmodulating frequency, or Timer 1
clock output specified by mode register 1 (MR1).
RES
I
System reset pin with pull-high resistor.
INT
I
External interrupt pin with pull-high resistor. This pin is bonding option for
the W741C250 body.
SEG0 to
SEG31
O
LCD segment output pins.
COM0 to
O
Also can be used as DC output ports specified by option codes.
LCD common signal output pins.
COM3
COM0
Static
1/2 Duty
1/3 Duty
1/4 Duty
Used
Used
Used
Used
Used
Used
Used
Used
Used
COM1
Not Used
COM2
Not Used
Not Used
COM3
Not Used
Not Used
Not Used
Used
The LCD alternating frequency can be selected by code option.
DH1, DH2
I
VDD1,
VDD2,
VDD3
I
Connection terminals for voltage doubler (halver) capacitor.
Positive (+) supply voltage terminal.
Refer to Functional Description.
-5-
Publication Release Date: March 1998
Revision A2
W741E260
Pin description, continued
SYMBOL
I/O
FUNCTION
VDD
I
Positive power supply (+).
VSS
I
Negative power supply (-).
VPP
I
Voltage control pin for the flash EEPROM programming, erasing and
verifying. This pin has a built-in pull-low resistor.
MODE
I
Mode selection pin for the flash EEPROM programming, erasing and
verifying. This pin has a built-in pull-low resistor.
DATA
I/O
Data I/O pin for the flash EEPROM programming and verifying. This pin
has a built-in pull-low resistor.
BLOCK DIAGRAM
COM0 to COM3
SEG0 to SEG31
LCD
RAM
(128 x 4)
ACC
DATA
Flash
EEPROM
(2048 x 16)
ALU
MODE
(look_up table
2K x 4)
VPP
STACK
(8 Levels)
Central Control
Unit
IEF
HEF
PEF
HCF
EVF
SEF
PSR0
SCR
PR
MR0
MR1
PM0
.
.
DH1 to 2
DRIVER
+1(+2)
PC
VDD1 to 3
PORT RA
RA0 to 3
PORT RB
RB0 to 3
PORT RC
RC0 to 3
PORT RD
RD0 to 3
PORT RE
RE0 to 3
.
SEL
MUX
Timer 0
(8-bit)
Modulation
Frequency
Pulse
Timer 1
(8-bit)
MFP
Divider 1
(13/14-bit)
VDD
Watchdog Timer
(4-bit)
Divider 0
(14-bit)
Timing Generator
VSS
INT
RES
XIN1 XOUT1
-6-
XIN2
XOUT2
W741E260
FUNCTIONAL DESCRIPTION
Program Counter (PC)
Organized as an 11-bit binary counter (PC0 to PC10), the program counter generates the addresses
ofthe 2048 × 16 on-chip flash EEPROM containing the program instruction. When the jump or
subroutine call instructions or the interrupt or initial reset conditions are to be executed, the address
corresponding to the instruction will be loaded into the program counter. The format used is shown
below.
ITEM
ADDRESS
INTERRUPT PRIORITY
Initial Reset
000H
-
INT 0 (Divider0)
004H
1st
INT 1 (Timer 0)
008H
2nd
INT 2 (Port RC)
00CH
3rd
INT 3 (Divider1 for W741C260;
INT pin for W741C250)
014H
4th
INT 4 (Timer 1)
020H
5th
JMP Instruction
XXXH
-
Subroutine Call
XXXH
-
Stack Register (STACK)
The stack register is organized as 11-bit x 8 levels (first-in, last-out). When either a call subroutine or
an interrupt is executed, the program counter will be pushed onto the stack register automatically. At
the end of a call subroutine or an interrupt service subroutine, the RTN instruction must be executed to
pop the contents of the stack register into the program counter. When the stack register is pushed over
the eighth level, the contents of the first level will be lost. In other words, the stack register is always
eight levels deep.
Program Memory (flash EEPROM)
The flash EEPROM is used to store program codes; the look-up table is arranged as 2048 × 4 bits.
The first three quarters of flash EEPROM (000H to 5FFH) are used to store instruction codes only, but
the last quarter (600H to 7FFH) can store both instruction codes and the look-up table. Each look-up
table element is composed of 4 bits, so the look-up table can be addressed up to 2048 elements.
There are two registers (TABL and TABH) to be used in look-up table addressing and they are
controlled by MOV TABH, R and MOV TABL, R instructions. When the instruction MOVC R is
executed, the contents of the look-up table location address specified by TABH, TABL and ACC will
be read and transferred to the data RAM. Refer to the instruction table for more details. The
organization of the program memory is shown in Figure 1.
-7-
Publication Release Date: March 1998
Revision A2
W741E260
16 bits
000H
TABH
TABL
ACC
- x x x x x x x x x y y
2048
address
Offset
0 1 1 x x x x x x x x x
ROM address = 600H + Offset/4
600H
3
2
1
0
This area can be used to store both instruction code
and look-up table
Each element (4 bits) of the look-up table
7FFH
2048 x 16-bit
Figure 1. Program Memory Organization
Data Memory (RAM)
1. Architecture
The static data memory (RAM) used to store data is arranged as 128 × 4 bits. The data memory can
be addressed directly or indirectly. The organization of the data memory is shown in Figure 2.
4 bits
00H
:
0FH
Working Register
128
address
7FH
128 x 4-bit
Figure 2. Data Memory Organization
-8-
W741E260
The first sixteen addresses (00H to 0FH) in the data memory are known as the working registers
(WR). The other data memory is used as general memory and cannot operate directly with immediate
data. The relationship between data memory locations and the page register (PAGE) in indirect
addressing mode is described in the next section.
2. Page Register (PAGE)
The page register is organized as a 4-bit binary register. The bit descriptions are as follows:
3
PAGE
2
1
0
R/W
R/W
R/W
Note: R/W means read/write available.
Bit 3 is reserved.
Bit 2, Bit 1, Bit 0 Indirect addressing mode preselect bits:
000 = Page 0 (00H - 0FH)
001 = Page 1 (10H - 1FH)
010 = Page 2 (20H - 2FH)
011 = Page 3 (30H - 3FH)
100 = Page 4 (40H - 4FH)
101 = Page 5 (50H - 5FH)
110 = Page 6 (60H - 6FH)
111 = Page 7 (70H - 7FH)
Accumulator (ACC)
The accumulator (ACC) is a 4-bit register used to hold results from the ALU and transfer data between
the memory, I/O ports, and registers.
Arithmetic and Logic Unit (ALU)
This is a circuit which performs arithmetic and logic operations. The ALU provides the following
functions:
• Logic operations: ANL, XRL, ORL
• Branch decisions: JB0, JB1, JB2, JB3, JNZ, JZ, JC, JNC, DSKZ, DSKNZ, SKB0, SKB1, SKB2, SKB3
• Shift operations: SHRC, RRC, SHLC, RLC
• Binary additions/subtractions: ADC, SBC, ADD, SUB, ADU, DEC, INC
After any of the above instructions are executed, the status of the carry flag (CF) and zero flag (ZF) is
stored in the internal registers. Otherwise CF can be stored or be read out by executing MOVA R, CF
or MOV CF, R.
-9-
Publication Release Date: March 1998
Revision A2
W741E260
Clock Generator
The W741E260 provides two oscillation circuits, main-oscillator and sub-oscillator. The main-oscillator
can select the crystal or RC oscillation circuit by option codes to generate the system clock through
external connections. If a crystal oscillator is used, a crystal or a ceramic resonator must be connected
to XIN1 and XOUT1, and a capacitor must be connected if an accurate frequency is needed. When the
oscillator is used, a high-frequency clock (400 KHz to 4 MHz) or low-frequency clock (32 KHz) can be
selected for the system clock by means of option codes. If the RC oscillator is used, a resistor must be
connected to XIN1 and XOUT1, and the high/low frequency clock option must be selected to suit the
operation frequency. The sub-oscillator must be connected to a 32.768 KHz crystal through XIN2 and
XOUT2 external pins when the dual-clock operation mode is selected by option code. The connection
is shown in Figure 3. One machine cycle consists of a four-state system clock sequence and can run
up to 1 µS with a 4 MHz system clock.
XIN2
XIN1
Crystal
32 KHz or
400K to 4MHz
or
Resistor
Crystal
32 KHz
XOUT1
XOUT2
Figure 3. System Clock Oscillator Configuration
Dual-clock operation
This operation mode is selected by code option. In the dual-clock mode, the clock source of the LCD
frequency selector should be the sub-oscillator clock (32768 Hz) only. But in the single-clock mode, the
clock source of the LCD frequency selector will be Fm or Fm/32 (Fm: main oscillator clock). So when
the STOP instruction is executing, the LCD will be turned off in the single-clock mode; but the LCD will
keep working in the dual-clock mode.
In this dual-clock mode, the normal operation is performed by generating the system clock from the
main-oscillator clock (Fm). As required, the slow operation can be performed by generating the system
clock from the sub-oscillator clock (Fs). The exchange of the normal operation and the slow operation
is performed by resetting or setting the bit 0 of the system clock control register (SCR). If the SCR.0 is
reset to 0, the clock source of the system clock generator is the main-oscillator clock; if the SCR.0 is
set to 1, the clock source of the system clock generator is the sub-oscillator clock. In the dual-clock
mode, the main-oscillator can stop oscillating when the STOP instruction is executing or the SCR.1 is
set to 1. But in the single-clock mode, only the STOP instruction can stop the main-oscillator
oscillating, because the SCR would be disabled in the single-clock mode. Therefore, in single-clock
mode, the clock source of the system clock generator is the main-oscillator clock (FOSC = Fm).
When the SCR is set or reset, we must pay attention to the following:
1. X000B → X011B: Disable the main-oscillator (Fm) should not be done simultaneously with changing
the system clock source (FOSC) from Fm to Fs. The FOSC should be changed first from Fm to Fs
before the main-oscillator (Fm) is disabled. The correct sequence is: X000B→X001B→X011B.
- 10 -
W741E260
2. X011B → X000B: Enabling the main-oscillator (Fm) should not be done simultaneously with
changing the FOSC from Fs into Fm. The main-oscillator (Fm) should be enabled first before a delay
subroutine is called to allow the main-oscillator to oscillate stably. The FOSC can now be changed
from Fs into Fm. The correct sequence is therefore X011B→X001B→delay subroutine→X000B.
The suggested delay for Fm is 20 mS for 455 KHz ceramic resonator and 10 mS for 4 MHz crystal.
We must remember that the X010B state is inhibitive, because it will induce a system shutdown.
The organization of the dual-clock operation mode is shown below.
Mask Option (High/Low Freq.)
HOLD
SCR.0
XIN1
XOUT1
Fm
Main Oscillator
Fosc
Fs
SCR.1
enable/disable
T1
T2
T3
T4
System Clock
Generator
Divider 0
Mask Option (High/Low Freq.)
Fosc/32
XIN2
XOUT2
Mask Option
(Single/Dual Clock)
LCD Frequency
Selector
Fosc
Sub-oscillator
FLCD
Mask Option (Single/Dual Clock)
enable/disable
Divider 1
INT4
HCF.4
SCR.3 (14/13 bit)
Figure 4. The Dual Clock Operation Mode Control Diagram
3
SCR
W
2
1
0
W
W
Note: W means write only.
Bit 0 = 0 Main oscillator is selected (Fosc = Fm)
= 1 Sub-oscillator is selected (Fosc = Fs)
Bit 1 = 0 Enable Fm
= 1 Disable Fm
Bit 2
Reserved
Bit 3 = 0 14-bit Divider1 is selected
= 1 13-bit Divider1 is selected
- 11 -
Publication Release Date: March 1998
Revision A2
W741E260
Dual clock operation mode:
- Sub-oscillator enable
- SCR.0 = 0, FOSC = Fm
- Flcd = Fs, in STOP mode LCD work continue
Single clock operation mode:
- Sub-oscillator disable
- SCR not use, Main oscillator enable, FOSC = Fm
- Flcd = FOSC (FOSC/32), in STOP mode LCD off
Divider
Each divider is organized as a 14-bit binary up-counter designed to generate periodic interrupts. When
the main oscillator starts action, the Divider0 is incremented by each clock (FOSC). When an overflow
occurs, the Divider0 event flag is set to 1 (EVF.0 = 1). The interrupt is executed if the Divider0 interrupt
enable flag has been set (IEF.0 = 1), and the hold state is terminated if the hold release enable flag
has been set (HEF.0 = 1). The last 4-stage of the Divider0 can be reset by executing a CLR DIVR0
instruction. If the main oscillator is connected to the 32768 Hz crystal, the EVF.0 will be set to 1
periodically at each 500 mS interval.
If the sub-oscillator is enabled, the Divider1 is incremented by each clock (Fs). When an overflow
occurs, the Divider1 event flag is set to 1 (EVF.4 = 1). The interrupt is executed if the Divider1 interrupt
enable flag has been set (IEF.4 = 1), and the hold state is terminated if the hold release enable flag
has been set (HEF.4 = 1). There are two time periods (250 mS & 500 mS) that can be selected by
setting the SCR.3 bit. When SCR.3 = 0 (default), the 500 mS period time is selected; when SCR.3 = 1,
the 250 mS period time is selected.
Watchdog Timer (WDT)
The watchdog timer (WDT) is organized as a 4-bit up counter and is designed to protect the program
from unknown errors. The WDT is enabled when the corresponding option code bit of the WDT is set
to 1. If the WDT overflows, the chip will be reset. At initial reset, the input clock of the WDT is
FOSC/1024. The input clock of the WDT can be switched to FOSC/16384 (or FOSC/1024) by executing
the SET PMF, #08H (or CLR PMF, #08H) instruction. The contents of the WDT can be reset by the
instruction CLR WDT. In normal operation, the application program must reset WDT before it
overflows. A WDT overflow indicates that the operation is not under control and the chip will be reset.
The WDT minimun overflow period is 468.75 mS when the system clock (FOSC) is 32 KHz and WDT
clock input is FOSC/1024. When the corresponding option code bit of the WDT is set to 0, and the
WDT function is disabled. The organization of the Divider0 and watchdog timer is shown in Figure 5.
- 12 -
W741E260
Divider0
Fosc
Q1
Q2
...Q9
HEF.0
S
Q10 Q11 Q12 Q13 Q14
R
R
R
R
R
Q
EVF.0
IEF.0
Hold mode release (HCF.0)
Divider0 interrupt (INT0)
1. Reset
2. CLR EVF, #01H
3. CLR DIVR0
Fosc/16384
WDT
PMF.3
Qw1 Qw2 Qw3 Qw4
Fosc/1024
R
Enable
/Disable
Mask Option
R
R
Overflow signal
System Reset
R
1. Reset
2. CLR WDT
Figure 5. Organization of Divider0 and Watchdog Timer
Parameter Flag (PMF)
The parameter flag is organized as a 4-bit binary register (PMF.0 to PMF.3). The PMF is controlled by
the SET PMF, #I or CLR PMF, #I instruction. The bit descriptions are as follows:
3
PMF
2
1
0
W
Note: W means write only.
Bit 0, Bit1, Bit2 Reserved
Bit 3 = 0 The fundamental frequency of the watchdog timer is FOSC/1024.
= 1 The fundamental frequency of the watchdog timer is FOSC/16384.
Timer/Counter
1. Timer 0 (TM0)
Timer 0 (TM0) is a programmable 8-bit binary down-counter. The specified value can be loaded into
TM0 by executing the MOV TM0L (TM0H), R or MOV TM0, #I instructions. When the MOV TM0L
(TM0H), R instructions are executed, the TM0 will stop down-counting (if the TM0 is down-counting),
the MR0.3 will be reset to 0, and the specified value is loaded into TM0. If MR0.3 is set to 1, the event
flag 1 (EVF.1) is reset and the TM0 starts to count. When it decrements to FFH, Timer 0 stops
operating and generates an underflow (EVF.1 = 1). The interrupt is executed if the Timer 0 interrupt
enable flag has been set (IEF.1 = 1); and the hold state is terminated if the hold release enable flag 1
has been set (HEF.1 = 1). The Timer 0 clock input can be set as FOSC/1024 or FOSC/4 by setting
MR0.0 to 1 or by resetting MR0.0 to 0. The default timer value is FOSC/4. The organization of Timer 0
is shown in Figure 6.
- 13 -
Publication Release Date: March 1998
Revision A2
W741E260
If the Timer 0 clock input is FOSC/4:
Desired time interval = (preset value +1) × 4 × 1/FOSC
If the Timer 0 clock input is FOSC/1024:
Desired time interval = (preset value +1) × 1024 × 1/FOSC
Preset value: Decimal number of Timer 0 preset value, and
FOSC: Clock oscillation frequency
1. Reset
2. CLR EVF, #02H
3. Reset MR0.3 to 0
4. MOV TM0L, R or MOV TM0H, R
MR0.0
Disable
Fosc/1024
HEF.1
8-bit Binary
Down Counter
(Timer 0)
Fosc/4
Enable
R
Q
EVF.1
8
MOV TM0H, R
Hold mode release (HCF.1)
IEF.1
Timer 0 interrupt (INT1)
4
4
1. Set MR0.3 to 1
2. MOV TM0, #I
S
MOV TM0L, R
MOV TM0, #I
1. Reset
2. CLR EVF, #02H
3. Set MR0.3 to 1
4. MOV TM0, #I
Figure 6. Organization of Timer 0
2. Timer 1 (TM1)
Timer 1 (TM1) is also a programmable 8-bit binary down counter, as shown in Figure . Timer 1 can be
used as a counter to count external events or to output an arbitrary frequency to the MFP pin. The
input clock of Timer 1 can be one of three sources: FOSC/64, FOSC, or an external clock from the RC.0
input pin. The source can be selected by setting bit 0 and bit 1 of mode register 1 (MR1). At initial
reset, the Timer 1 clock input is FOSC. If an external clock is selected as the clock source of Timer 1,
the content of Timer 1 is decreased by 1 at the falling edge of RC.0. When the MOV TM1L, R or MOV
TM1H, R instruction is executed, the specified data are loaded into the auto-reload buffer and the TM1
down-counting will be disabled (i.e. MR1.3 is reset to 0). If the bit 3 of MR1 is set (MR1.3 = 1), the
contents of the auto-reload buffer will be loaded into the TM1 down counter, Timer 1 starts to down
count, and the event flag 7 is reset (EVF.7 = 0). When the MOV TM1, #I instruction is executed, the
event flag 7 (EVF.7) and MR1.3 are reset and the specified value is loaded into auto-reload buffer and
TM1 by the internal hardware, then the MR1.3 is set, that is the TM1 starts to count by the hardware.
When the timer decrements to FFH, it will generate an underflow (EVF.7 = 1) and be auto-reloaded
with the specified data, after which it will continue to count down. An interrupt is executed if the
interrupt enable flag 7 has been set to 1 (IEF.7 = 1), and the hold state is terminated if the hold mode
release enable flag 7 is set to 1 (HEF.7 = 1). The specified frequency of Timer 1 can be delivered to
the MFP output pin by programming bit 2 of MR1. Bit 3 of MR1 can be used to make Timer 1 stop or
start counting.
If the Timer 1 clock input is FT, then:
- 14 -
W741E260
Desired timer interval = (preset value +1) / FT
Desired frequency for MFP output pin = FT ÷ (preset value + 1) ÷ 2 (Hz)
Preset value: Decimal number of Timer 1 preset value, and
FOSC: Clock oscillation frequency
MOV TM1, #I
MOV TM1L, R
MOV TM1H, R
8
1. MR1.3 = 1
2. MOV TM1, #I
Underflow
signal
4
4
MR1.1
8 bits
Enable
FT
8-bit Binary
Down Counter
(Timer 1)
Fosc/64
Fosc
MR1.0
Disable
Reset
Set MR1.3 to 1
MOV TM1, #I
Q
EVF.7
1. Reset
2. INT 7 accept
3. CLR EVF, #80H
4. Set MR1.3 to 1
5. MOV TM1, #I
Auto-reload buffer
External clock
via RC.0
S
R
2
circuit
MFP
output pin
Reset
MR1.2
MFP signal
1. MR1.3 = 0
Figure 7. Organization of Timer 1
For example, when FT equals 32768 Hz, depending on the preset value of TM1, the MFP pin will
output a single tone signal in the tone frequency range from 64 Hz to 16384 Hz. The relation between
the tone frequency and the preset value of TM1 is shown in the table below.
- 15 -
Publication Release Date: March 1998
Revision A2
W741E260
3rd octave
Tone
frequency
4th octave
TM1 preset value &
MFP frequency
Tone
frequency
5th octave
TM1 preset value &
MFP frequency
Tone
frequency
TM1 preset value &
MFP frequency
C
130.81
7CH
131.07
261.63
3EH
260.06
523.25
1EH
528.51
C#
138.59
75H
138.84
277.18
3AH
277.69
554.37
1CH
564.96
585.14
D
146.83
6FH
146.28
293.66
37H
292.57
587.33
1BH
D#
155.56
68H
156.03
311.13
34H
309.13
622.25
19H
630.15
O
E
164.81
62H
165.49
329.63
31H
327.68
659.26
18H
655.36
F
174.61
5DH
174.30
349.23
2EH
372.36
698.46
16H
712.34
N
F#
185.00
58H
184.09
369.99
2BH
390.09
739.99
15H
744.72
G
196.00
53H
195.04
392.00
29H
420.10
783.99
14H
780.19
E
G#
207.65
4EH
207.39
415.30
26H
443.81
830.61
13H
819.20
A
220.00
49H
221.40
440.00
24H
442.81
880.00
12H
862.84
A#
233.08
45H
234.05
466.16
22H
468.11
932.23
11H
910.22
B
246.94
41H
248.24
493.88
20H
496.48
987.77
10H
963.76
T
Note: Central tone is A4 (440 Hz).
Mode Register 0 (MR0)
Mode Register 0 is organized as a 4-bit binary register (MR0.0 to MR0.3). MR0 can be used to control
the operation of Timer 0. The bit descriptions are as follows:
3
MR0
2
1
W
0
W
Note: W means write only.
Bit 0 = 0
=1
The fundamental frequency of Timer 0 is FOSC/4.
The fundamental frequency of Timer 0 is FOSC/1024.
Bit 1 & Bit 2 are reserved
Bit 3 = 0
Timer 0 stops down-counting.
=1
Timer 0 starts down-counting.
Mode Register 1 (MR1)
Mode Register 1 is organized as a 4-bit binary register (MR1.0 to MR1.3). MR1 can be used to control
the operation of Timer 1. The bit descriptions are as follows:
MR1
3
2
1
0
W
W
W
W
Note: W means write only.
- 16 -
W741E260
Bit 0 = 0 The internal fundamental frequency of Timer 1 is FOSC.
= 1 The internal fundamental frequency of Timer 1 is FOSC/64.
Bit 1 = 0 The fundamental frequency source of Timer 1 is the internal clock.
= 1 The fundamental frequency source of Timer 1 is the external clock from RC.0 input pin.
Bit 2 = 0 The specified waveform of the MFP generator is delivered at the MFP output pin.
= 1 The specified frequency of Timer 1 is delivered at the MFP output pin.
Bit 3 = 0 Timer 1 stops down-counting.
= 1 Timer 1 starts down-counting.
Input/Output Ports RA, RB
Port RA consists of pins RA.0 to RA.3 and Port RB consists of pins RB.0 to RB.3. At initial reset,
input/output ports RA and RB are both in input mode. When RA and RB are used as output ports,
CMOS or NMOS open drain output type can be selected by the PM0 register. Each pin of port RA or
RB can be specified as input or output mode independently by the PM1 and PM2 registers. The MOVA
R, RA or MOVA R, RB instructions operate the input functions and the MOV RA, R or MOV RB, R
operate the output functions. For more details, refer to the instruction table and Figure 8.
Input/Output Pin of the RA(RB)
Vdd
PM0.0 (or PM0.1)
Output
Buffer
DATA
BUS
I/O PIN
RA.n(RB.n)
Enable
MOV RA, R
(or MOV RB, R)
Instruction
PM1.n
(or PM2.n)
Enable
MOVA R, RA
(or MOVA R, RB)
instruction
Figure 8. Architecture of Input/Output Pins
- 17 -
Publication Release Date: March 1998
Revision A2
W741E260
Port Mode 0 Register (PM0)
The port mode 0 register is organized as 4-bit binary register (PM0.0 to PM0.3). PM0 can be used to
determine the structure of the input/output ports; it is controlled by the MOV PM0, #I instruction. The bit
descriptions are as follows:
PM0
3
2
1
0
w
w
w
w
Note: W means write only.
Bit 0 = 0 RA port is CMOS output type. Bit 0 = 1 RA port is NMOS open drain output type.
Bit 1 = 0 RB port is CMOS output type. Bit 1 = 1 RB port is NMOS open drain output type.
Bit 2 = 0 RC port pull-high resistor is disabled. Bit 2 = 1 RC port pull-high resistor is enabled.
Bit 3 = 0 RD port pull-high resistor is disabled. Bit 3 = 1 RD port pull-high resistor is enabled.
Port Mode 1 Register (PM1)
The port mode 1 register is organized as 4-bit binary register (PM1.0 to PM1.3). PM1 can be used to
control the input/output mode of port RA. PM1 is controlled by the MOV PM1, #I instruction. The bit
descriptions are as follows:
PM1
3
2
1
0
w
w
w
w
Note: W means write only.
Bit 0 = 0 RA.0 works as output pin; Bit 0 = 1 RA.0 works as input pin
Bit 1 = 0 RA.1 works as output pin; Bit 1 = 1 RA.1 works as input pin
Bit 2 = 0 RA.2 works as output pin; Bit 2 = 1 RA.2 works as input pin
Bit 3 = 0 RA.3 works as output pin; Bit 3 = 1 RA.3 works as input pin
At initial reset, port RA is input mode (PM1 = 1111B).
Port Mode 2 Register (PM2)
The port mode 2 register is organized as 4-bit binary register (PM2.0 to PM2.3). PM2 can be used to
control the input/output mode of port RB. PM2 is controlled by the MOV PM2, #I instruction. The bit
descriptions are as follows:
PM2
3
2
1
0
w
w
w
w
Note: W means write only.
- 18 -
W741E260
Bit 0 = 0 RB.0 works as output pin; Bit 0 = 1 RB.0 works as input pin
Bit 1 = 0 RB.1 works as output pin; Bit 1 = 1 RB.1 works as input pin
Bit 2 = 0 RB.2 works as output pin; Bit 2 = 1 RB.2 works as input pin
Bit 3 = 0 RB.3 works as output pin; Bit 3 = 1 RB.3 works as input pin
At initial reset, the port RB is input mode (PM2 = 1111B).
Input Ports RC & RD
Port RC consists of pins RC.0 to RC.3, and port RD consists of pins RD.0 to RD.3. Each pin of port RC
and port RD can be connected to a pull-up resistor, which is controlled by the port mode 0 register
(PM0). When the PEF, HEF, and IEF corresponding to the RC port are set, a signal change on the
specified pins of port RC will execute the hold mode release or interrupt subroutine. Port status register
0 (PSR0) records the status of ports RC, i.e., any signal changes on the pins that make up the port.
PSR0 can be read out and cleared by the MOV R, PSR0, and CLR PSR0 instructions. In addition, the
falling edge signal on the pin of port RC specified by the instruction MOV SEF, #I will cause the device
to exit the stop mode. Refer to Figure 9 and the instruction table for more details. The RD port is used
as input port only, it has no hold mode release, wake-up stop mode or interrupt functions.
Port Status Register 0 (PSR0)
Port status register 0 is organized as 4-bit binary register (PSR0.0 to PSR0.3). PSR0 can be read or
cleared by the MOVA R, PSR0, and CLR PSR0 instructions. The bit descriptions are as follows:
PSR0
3
2
1
0
R
R
R
R
Note: R means read only.
Bit 0 = 1
Signal change at RC.0
Bit 1 = 1
Signal change at RC.1
Bit 2 = 1
Signal change at RC.2
Bit 3 = 1
Signal change at RC.3
Port Enable Flag (PEF)
The port enable flag is organized as 4-bit binary register (PEF.0 to PEF.3). Before port RC may be
used to release the hold mode or perform interrupt function, the content of the PEF must be set first.
The PEF is controlled by the MOV PEF, #I instruction. The bit descriptions are as follows:
PEF
3
2
1
0
w
w
w
w
Note: W means write only.
- 19 -
Publication Release Date: March 1998
Revision A2
W741E260
PEF.0: Enable/disable the signal change at pin RC.0 to release hold mode or perform interrupt.
PEF.1: Enable/disable the signal change at pin RC.1 to release hold mode or perform interrupt.
PEF.2: Enable/disable the signal change at pin RC.2 to release hold mode or perform interrupt.
PEF.3: Enable/disable the signal change at pin RC.3 to release hold mode or perform interrupt.
DATA BUS
PEF.0
PM0.2
D
ck
Signal
change
detector
RC.0
Q
PSR0.0
R
HEF.2
PEF.1
PM0.2
D
ck
Signal
change
detector
RC.1
Q
D
ck
PSR0.1
Q
EVF.2
HCF.2
R
R
IEF.2
INT 2
PEF.2
PM0.2
D
ck
Signal
change
detector
RC.2
Q
PSR0.2
CLR EVF, #I
R
Reset
PEF.3
PM0.2
RC.3
D
ck
Signal
change
detector
Q
PSR0.3
R
Reset
MOV PEF, #I
CLR PSR0
SEF.0
Falling
edge
detector
SEF.1
Falling
edge
detector
Wake up from STOP mode
SEF.2
Falling
edge
detector
SEF.3
Falling
edge
detector
Figure 9. Architecture of Input Port RC
Output Port RE
When the MOV RE, R instruction is executed, the data in the RAM will be output to port RE and it
provides a high sink current to drive LEDs.
MFP Output Pin (MFP)
The MFP output pin can output the Timer 1 clock or the modulation frequency; the output of the pin is
determined by mode register 1 (MR1). The configuration of MFP is shown in Figure 9. When bit 2 of
MR1 is reset to "0," the MFP output can deliver a modulation output in any combination of one signal
from among DC, 4096Hz, 2048Hz, and one or more signals from among 128 Hz, 64 Hz, 8 Hz, 4 Hz, 2
Hz, or 1 Hz (when using a 32.768 KHz crystal). The MOV MFP, #I instruction is used to specify the
- 20 -
W741E260
modulation output combination. The data specified by the 8-bit operand and the MFP output pin are
shown below.
(Fosc = 32.768 KHz)
R7 R6
0 0
0 1
1 0
1 1
R5
R4
R3
R2
R1
R0
0
0
0
0
0
0
Low level
0
0
0
0
0
1
128 Hz
0
0
0
0
1
0
64 Hz
0
0
0
1
0
0
8 Hz
0
0
1
0
0
0
4 Hz
0
1
0
0
0
0
2 Hz
1
0
0
0
0
0
1 Hz
0
0
0
0
0
0
High level
0
0
0
0
0
1
128 Hz
0
0
0
0
1
0
64 Hz
0
0
0
1
0
0
8 Hz
0
0
1
0
0
0
4 Hz
0
1
0
0
0
0
2 Hz
1
0
0
0
0
0
1 Hz
0
0
0
0
0
0
2048 Hz
0
0
0
0
0
1
2048 Hz * 128 Hz
0
0
0
0
1
0
2048 Hz * 64 Hz
0
0
0
1
0
0
2048 Hz * 8 Hz
0
0
1
0
0
0
2048 Hz * 4 Hz
0
1
0
0
0
0
2048 Hz * 2 Hz
1
0
0
0
0
0
2048 Hz * 1 Hz
0
0
0
0
0
0
4096 Hz
0
0
0
0
0
1
4096 Hz * 128 Hz
0
0
0
0
1
0
4096 Hz * 64 Hz
0
0
0
1
0
0
4096 Hz * 8 Hz
0
0
1
0
0
0
4096 Hz * 4 Hz
0
1
0
0
0
0
4096 Hz * 2 Hz
1
0
0
0
0
0
4096 Hz * 1 Hz
- 21 -
FUNCTION
Publication Release Date: March 1998
Revision A2
W741E260
Interrupts
The W741E260 provides four internal interrupt sources (Divider 0, Divider 1, Timer 0, Timer 1) and
one external interrupt source (port RC) for W741C260 body or three internal interrupt sources (Divider
0, Timer 0, Timer 1) and two external interrupt sources ( port RC, INT pin) for W741C250 body.
Vector addresses for each of the interrupts are located in the range of program memory (ROM)
addresses 004H to 020H. The flags IEF, PEF, and EVF are used to control the interrupts. When EVF
is set to "1" by hardware and the corresponding bits of IEF and PEF have been set by software, an
interrupt is generated. When an interrupt occurs, all of the interrupts are inhibited until the EN INT or
MOV IEF, #I instruction is invoked. The interrupts can also be disabled by executing the DIS INT
instruction. When an interrupt is generated in hold mode, the hold mode will be released momentarily
and interrupt subroutine will be executed. After the RTN instruction is executed in an interrupt
subroutine, the µC will enter hold mode again. The operation flow chart is shown in Figure 11. The
control diagram is shown below.
Divider 0
overflow signal
EN INT
MOV IEF, #I
S
Q
S
Q
IEF.0
EVF.1
IEF.1
R
Port RC
signal change
S
Q
EVF.2
IEF.2
R
Divider 1
overflow signal
S
Q
S
Q
R
004H
Interrupt
Process
Circuit
Interrupt
Vector
Generator
008H
00CH
014H
020H
EVF.4
IEF.4
R
Timer 1
underflow
signal
Enable
EVF.0
R
Timer 0
underflow signal
Initial Reset
EVF.7
IEF.7
Initial Reset
Disable
CLR EVF, #I instruction
DIS INT instruction
Figure 10. Interrupt Event Control Diagram
Interrupt Enable Flag (IEF)
The interrupt enable flag is organized as an 8-bit binary register (IEF.0 to IEF.7). These bits are used
to control the interrupt conditions. It is controlled by the MOV IEF, #I instruction. When one of these
interrupts is accepted, the corresponding to the bit of the event flag will be reset, but the other bits are
unaffected. In interrupt subroutine, these interrupts will be disabled till the instruction MOV IEF, #I or
EN INT is executed again. Otherwise, these interrupts can be disabled by executing DIS INT
instruction. The bit descriptions are as follows:
- 22 -
W741E260
7
IEF
6
5
w
4
3
w
2
1
0
w
w
w
Note: W means write only.
IEF.0 = 1 Interrupt 0 is accepted by overflow from the Divider 0.
IEF.1 = 1 Interrupt 1 is accepted by underflow from the Timer 0.
IEF.2 = 1 Interrupt 2 is accepted by a signal change at port RC.
IEF.3 is reserved.
IEF.4 = 1 Interrupt 4 is accepted by overflow from the Divider 1 for W741C260 body.
Interrupt 4 is accepted by a falling edge signal at the INT pin for W741C250 body.
IEF.5 & IEF.6 are reserved.
IEF.7 = 1 Interrupt 7 is accepted by underflow from Timer 1.
Stop Mode Operation
In stop mode, all operations of the µC cease (excluding the operation of the sub-oscillator and divider 1
when the dual-clock operation mode is selected). The µC enters stop mode when the STOP instruction
is executed and exits stop mode when an external trigger is activated (by a falling signal on the RC
port for W741C260 body or by a falling signal on the RC port or a low level on the INT pin for
W741C250 body). When the designated signal is accepted, the µC awakens and executes the next
instruction (if the corresponding bits of IEF and PEF have been set, It will enter the interrupt service
routine after stop mode released). To prevent erroneous execution, the NOP instruction should follow
the STOP command. But In the dual-clock slow operation mode, the STOP instruction will disable the
main-oscillator oscillating; the µC system is still operated by the sub-oscillator.
Stop Mode Wake-up Enable Flag for RC Port (SEF)
The stop mode wake-up flag for port RC is organized as an 4-bit binary register (SEF.0 to SEF.3).
Before port RC may be used to make the device exit the stop mode, the content of the SEF must be
set first. The SEF is controlled by the MOV SEF, #I instruction. The bit descriptions are as follows:
SEF
3
2
1
0
w
w
w
w
Note: W means write only.
SEF.0 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.0
SEF.1 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.1
SEF.2 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.2
SEF.3 = 1 Device will exit stop mode when falling edge signal is applied to pin RC.3
- 23 -
Publication Release Date: March 1998
Revision A2
W741E260
Hold Mode Operation
In hold mode, all operations of the µC cease, except for the operation of the oscillator, Timer, Divider
and LCD driver. The µC enters hold mode when the HOLD instruction is executed. The hold mode can
be released in one of five ways: by the action of timer 0, timer 1, divider 0, divider 1, the RC port.
Before the device enters the hold mode, the HEF, PEF, and IEF flags must be set to define the hold
mode release conditions. For more details, refer to the instruction-set table and the following flow
chart.
Divider 0, Divider 1, Timer
0, Timer 1, Signal Change
at RC Port
In
HOLD
Mode?
Yes
Interrupt
Enable?
No
No
Interrupt
Enable?
Yes
IEF
Flag Set?
Yes
No
IEF
Flag Set?
Yes
No
Yes
Reset EVF Flag
Execute
Interrupt Service
Routine
Reset EVF Flag
Execute
Interrupt Service
Routine
HEF
Flag Set?
No
(Note)
No
Yes
(Note)
Disable interrupt
Disable interrupt
HOLD
PC <- (PC+1)
Note: The bit of EVF corresponding to the interrupt signal will be reset.
Figure 11. Hold Mode and Interrupt Operation Flow Chart
- 24 -
W741E260
Hold Mode Release Enable Flag (HEF)
The hold mode release enable flag is organized as an 8-bit binary register (HEF.0 to HEF.7). The HEF
is used to control the hold mode release conditions. It is controlled by the MOV HEF, #I instruction. The
bit descriptions are as follows:
7
HEF
6
5
w
4
3
w
2
1
0
w
w
w
Note: W means write only.
HEF.0 = 1 Overflow from the Divider 0 causes Hold mode to be released.
HEF.1 = 1 Underflow from Timer 0 causes Hold mode to be released.
HEF.2 = 1 Signal change at port RC causes Hold mode to be released.
HEF.3 is reserved.
HEF.4 = 1 Overflow from the Divider 1 causes Hold mode to be released for W741C260 body.
Falling edge signal at the INT pin causes Hold mode to be released for W741C250 body.
HEF.5 & HEF.6 are reserved.
HEF.7 = 1 Underflow from Timer 1 causes Hold mode to be released.
Hold Mode Release Condition Flag (HCF)
The hold mode release condition flag is organized as a 8-bit binary register (HCF.0 to HCF.7). It
indicates by which interrupt source the hold mode has been released, and is loaded by hardware. The
HCF can be read out by the MOVA R, HCFL and MOVA R, HCFH instructions. When any of the HCF
bits is "1," the hold mode will be released and the HOLD instruction is invalid. The HCF can be reset by
the CLR EVF or MOV HEF, #I (HEF = 0) instructions. When EVF and HEF have been reset, the
corresponding bit of HCF is reset simultaneously. The bit descriptions are as follows:
7
HCF
6
5
4
R
R
3
2
1
0
R
R
R
Note: R means read only.
HCF.0 = 1 Hold mode was released by overflow from the divider 0.
HCF.1 = 1 Hold mode was released by underflow from the timer 0.
HCF.2 = 1 Hold mode was released by a signal change at port RC.
HCF.3 is reserved.
HCF.4 = 1 Hold mode was released by overflow from the divider 1 for W741C260 body.
Hold mode was released by a falling edge signal at the INT pin for W741C250 body.
HCF.5 = 1 Hold mode was released by underflow from the timer 1.
HCF.6 and HCF.7 are reserved.
- 25 -
Publication Release Date: March 1998
Revision A2
W741E260
Event Flag (EVF)
The event flag is organized as a 8-bit binary register (EVF.0 to EVF.7). It is set by hardware and reset
by CLR EVF, #I instruction or the occurrence of an interrupt. The bit descriptions are as follows:
7
EVF
6
5
R
4
3
R
2
1
0
R
R
R
Note: R means read only.
EVF.0 = 1 Overflow from divider 0 occurred.
EVF.1 = 1 Underflow from timer 0 occurred.
EVF.2 = 1 Signal change at port RC occurred.
EVF.3 is reserved.
EVF.4 = 1 Overflow from divider 1 occurred for W741C260 body.
Falling edge signal at the INT pin occurred for W741C250 body.
EVF.5 & EVF.6 are reserved.
EVF.7 = 1 Underflow from Timer 1 occurred.
Reset Function
The W741E260 is reset either by a power-on reset or by using the external RES pin. The initial state
of the W741E260 after the reset function is executed is described below.
Program Counter (PC)
TM0, TM1
MR0, MR1, PAGE registers
PSR0 registers
IEF, HEF, HCF, PEF, EVF, SEF flags
SCR register
Timer 0 input clock
Timer 1 input clock
MFP output
Input/output ports RA, RB
Output port RE
RA & RB ports output type
RC & RD ports pull-high resistors
Input clock of the watchdog timer
LCD display
Segment output mode
- 26 -
000H
Reset
Reset
Reset
Reset
Reset
FOSC/4
FOSC
Low
Input mode
High
CMOS type
Disable
FOSC/1024
OFF
LCD drive output
W741E260
LCD Controller/Driver
The W741E260 can directly drive an LCD with 32 segment output pins and 4 common output pins for a
total of 32 × 4 dots. Option codes can be used to select one of five options for the LCD driving mode:
static, 1/2 Bias 1/2 duty, 1/2 Bias 1/3 duty, 1/3 Bias 1/3 duty, or 1/3 Bias 1/4 duty (see Figure 13). The
alternating frequency of the LCD can be set as Fw/64, Fw/128, Fw/256, or Fw/512. In addition, option
codes can also be used to set up four of the LCD driver output pins (segment 0 to segment 31) as a
DC output port. The structure of the LCD alternating frequency (FLCD) is shown in Figure 12.
Fosc or Fosc/32
Fw
Q1
Fs
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Fw/64
Fw/128
Fw/256
Fw/512
Mask Option
(Single/Dual Clock)
FLCD
Selector
Figure 12. LCD Alternating Frequency (FLCD) Circuit Diagram
Data Bus
Option Codes
LCD frequency
selection
Fw
Clock
Generator
LCD drive
mode
selection
LCD Mode
Controller
LCD DATA RAM
(32 x 4 bits)
MOV LCDM,#I
instruction
LCD duty & bias
FLCD
DH1
DH2
LCD Voltage
Controller
Commom
Driver
VDD
VSS
VDD1 to 3
COM0 to 3
LCD
waveform
Segment
Driver/Controller
SEG0 to 31
Figure 13. LCD Driver/Controller Circuit Diagram
- 27 -
Publication Release Date: March 1998
Revision A2
W741E260
When Fw = 32.768 KHz, the LCD frequency is as shown in the table below.
LCD Frequency
Fw/512 (64 Hz)
Fw/256 (128 Hz)
Fw/128 (256 Hz)
Fw/64 (512 Hz)
Static
64
128
256
512
1/2 Duty
32
64
128
256
1/3 Duty
21
43
85
171
1/4 Duty
16
32
64
128
Corresponding to the 32 LCD drive output pins, there are 32 LCD data RAM segments (LCDR00 to
LCDR1F). Instructions such as MOV LCDR, #I; MOV WR, LCDR; MOV LCDR, WR; and MOV LCDR,
ACC are used to control the LCD data RAM. The data in the LCD data RAM are transferred to the
segment output pins automatically without program control. When the bit value of the LCD data RAM is
"1," the LCD is turned on. When the bit value of the LCD data RAM is "0," LCD is turned off. The
contents of the LCD data RAM (LCDR) are sent out through the segment0 to segment31 pins by a
direct memory access. The relation between the LCD data RAM and segment/common pins is shown
below.
LCD Data RAM
LCDR00
LCDR01
.
.
.
LCDR1E
LCDR1F
Output Pin
SEG0
SEG1
.
.
.
SEG30
SEG31
COM3
bit 3
0/1
0/1
.
.
.
0/1
0/1
COM2
bit 2
0/1
0/1
.
.
.
0/1
0/1
COM1
bit 1
0/1
0/1
.
.
.
0/1
0/1
COM0
bit 0
0/1
0/1
.
.
.
0/1
0/1
The LCDON instruction turns the LCD display on (even in HOLD mode), and the LCDOFF instruction
turns the LCD display off. At initial reset, all the LCD segments are lit. When the initial reset state ends,
the LCD display is turned off automatically. To turn on the LCD display, the instruction LCDON must be
executed. When the drive output pins are used as DC output ports (setting by option codes, please
refer the user's manual of ASM741S assembler for more detail), CMOS output type or NMOS output
type can be selected by executing the instruction MOV LCDM, #I. The relationship between the LCD
data RAM and segment/common pins is shown below. The data in LCDR00 are transferred to the
corresponding segment output port (SEG3 to SEG0) by a direct memory access. The other LCD data
RAM segments can be used as normal data RAM to store data.
LCD Data RAM
LCDR00
LCDR03-LCDR01
LCDR04
LCDR07-LCDR05
.
.
.
LCDR1C
LCDR1F-LCDR1D
Output Pin
SEG3-SEG0
SEG7-SEG4
.
.
.
SEG31-SEG30
-
Bit 3
SEG3
SEG7
.
.
.
SEG31
-
- 28 -
Bit 2
SEG2
SEG6
.
.
.
SEG30
-
Bit 1
SEG1
SEG5
.
.
.
SEG29
-
Bit 0
SEG0
SEG4
.
.
.
SEG28
-
W741E260
The relationship between the LCD drive mode and the maximum number of drivable LCD segments is
shown below.
LCD Drive Mode
Max. Number of Drivable
LCD Segment
STATIC
Connection at
Power Input
32 (COM0)
Connect VDD3, VDD2 to VDD1
1/2 Bias 1/2 Duty
64 (COM0-COM1)
Connect VDD3 to VDD2
1/2 Bias 1/3 Duty
96 (COM0-COM2)
Connect VDD3 to VDD2
1/3 Bias 1/3 Duty
96 (COM0-COM2)
-
1/3 Bias 1/4 Duty
128 (COM0-COM3)
-
LCD Output Mode Type Flag (LCDM)
The LCD output mode type flag is organized as an 8-bit binary register (LCDM.0 to LCDM.7). These
bits are used to control the LCD output pins architecture. When LCD output pins are set to DC output
mode by option codes, the architecture of these output pins (segment 0 to segment 31) can be
selected as CMOS or NMOS type. It is controlled by the MOV LCDM, #I instruction. The bit
descriptions are as follows:
LCDM
7
6
5
4
3
2
1
0
w
w
w
w
w
w
w
w
Note: W means write only.
LCDM.0 = 0 SEG0 to SEG3 work as CMOS output type.
= 1 SEG0 to SEG3 work as NMOS output type.
LCDM.1 = 0 SEG4 to SEG7 work as CMOS output type.
= 1 SEG4 to SEG7 work as NMOS output type.
LCDM.2 = 0 SEG8 to SEG11 work as CMOS output type.
= 1 SEG8 to SEG11 work as NMOS output type.
LCDM.3 = 0 SEG12 to SEG15 work as CMOS output type.
= 1 SEG12 to SEG15 work as NMOS output type.
LCDM.4 = 0 SEG16 to SEG19 work as CMOS output type.
= 1 SEG16 to SEG19 work as NMOS output type.
LCDM.5 = 0 SEG20 to SEG23 work as CMOS output type.
= 1 SEG20 to SEG23 work as NMOS output type.
LCDM.6 = 0 SEG24 to SEG27 work as CMOS output type.
= 1 SEG24 to SEG27 work as NMOS output type.
LCDM.7 = 0 SEG28 to SEG31 work as CMOS output type.
= 1 SEG28 to SEG31 work as NMOS output type.
The output waveforms for the five LCD driving modes are shown below.
- 29 -
Publication Release Date: March 1998
Revision A2
W741E260
Static Lighting System (Example)
Normal Operating Mode
VDD2
VDD1
VSS
COM0
VDD2
VDD1
VSS
Unlit LCD driver
outputs
Lit LCD driver
outputs
VDD2
VDD1
VSS
1/2 Bias 1/2 duty Lighting System (Example)
Normal Operating Mode
VDD2
VDD1
VSS
COM0
VDD2
VDD1
VSS
COM1
LCD driver
outputs for
seg. on COM0,
COM1 sides
being unlit
VDD2
VDD1
VSS
LCD driver
outputs for
only seg. on
COM0 side
being lit
VDD2
VDD1
VSS
- 30 -
W741E260
1/2 Bias 1/2 duty Lighting System (Example) - Normal Operating Mode, continued
LCD driver
outputs for
only seg. on
COM1 side
being lit
VDD2
VDD1
VSS
LCD driver
outputs for
seg. on COM0,
COM1 sides
being lit
VDD2
VDD1
VSS
1/2 Bias 1/3 duty Lighting System (Example)
Normal Operating Mode
VDD2
VDD1
VSS
COM0
COM1
VDD2
VDD1
VSS
COM2
VDD2
VDD1
VSS
VDD2
VDD1
VSS
LCD driver
outputs for all
seg. on COM0,1,2
sides being unlit
LCD driver
outputs for only
seg. on COM0
side being lit
VDD2
VDD1
VSS
LCD driver
outputs for only
seg. on COM1
side being lit
VDD2
VDD1
VSS
LCD driver
outputs for only
seg. on COM0,1
sides being lit
VDD2
VDD1
VSS
- 31 -
Publication Release Date: March 1998
Revision A2
W741E260
1/2 Bias 1/3 duty Lighting System (Example) - Normal Operating Mode, continued
LCD driver
outputs for only
seg. on COM2
side being lit
VDD2
VDD1
VSS
LCD driver
outputs for only
seg. on COM0,2
sides being lit
VDD2
VDD1
VSS
1/3 Bias 1/3 duty Lighting System (Example)
Normal Operating Mode
VDD3
VDD2
VDD1
VSS
COM0
VDD3
VDD2
VDD1
VSS
COM1
VDD3
VDD2
VDD1
VSS
COM2
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for all
seg. on COM0,1,2
sides being unlit
LCD driver
outputs for only
seg. on COM0
side being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for only
seg. on COM1
side being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for seg.
on COM0,2
sides being lit
VDD3
VDD2
VDD1
VSS
- 32 -
W741E260
1/3 Bias 1/3 duty Lighting System (Example) - Normal Operating Mode, continued
LCD driver
outputs for seg.
on COM1,2
sides being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for seg.
on COM0,1,2
sides being lit
VDD3
VDD2
VDD1
VSS
1/3 Bias 1/4 duty Lighting System (Example)
Normal Operating Mode
VDD3
VDD2
VDD1
VSS
COM0
VDD3
VDD2
VDD1
VSS
COM1
VDD3
VDD2
VDD1
VSS
COM2
VDD3
VDD2
VDD1
VSS
COM3
LCD driver
outputs for
only seg. on
COM0 side
being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for
only seg. on
COM1 side
being lit
VDD3
VDD2
VDD1
VSS
- 33 -
Publication Release Date: March 1998
Revision A2
W741E260
1/3 Bias 1/4 duty Lighting System (Example) - Normal Operating Mode, continued
LCD driver
outputs for
seg. on COM0,
COM1 sides
being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for
seg. on COM1,
COM2,3 sides
being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for
seg. on COM1
COM2 sides
being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for
seg. on COM0
COM2,3 sides
being lit
VDD3
VDD2
VDD1
VSS
LCD driver
outputs for
seg. on COM0
COM1,2,3 sides
being lit
VDD3
VDD2
VDD1
VSS
- 34 -
W741E260
The power connections for each LCD driving mode, which are determined by a mask option, are
shown below.
Static LCD Configuration
1/2 Bias LCD Configuration
DH1
DH1
0.1uF
DH1, DH2 floating
DH2
DH2
VSS
C
H
I
P
VSS
VDD
VDD
C
H
I
P
VDD
VDD
0.1uF
VDD1
VDD1
VDD2
VDD2
VDD3
VDD3
VDD1 = 1/2 VDD, VDD2 = VDD3 = VDD
VDD1 = VDD2 = VDD3 = VDD
1/3 Bias LCD Configuration
DH1
0.1uF
DH2
VSS
C
H
I
P
VDD
VDD
0.1uF
VDD1
VDD2
VDD3
VDD1 = 1/2 VDD, VDD2 = VDD, VDD3 = 3/2 VDD
- 35 -
Publication Release Date: March 1998
Revision A2
W741E260
LCD Configuration, continued
1/3 Bias LCD Configuration
DH1
0.1uF
DH2
VSS
C
H
I
P
VDD
VDD
0.1uF
VDD1
VDD2
VDD3
VDD1 = 1/3 VDD, VDD2 = 2/3 VDD, VDD3 = VDD
EEPROM Program/Erase Description
The built-in program code memory of the W741E260 is the EEPROM structure. This memory can be
programmed, erased and verified through the VPP, MODE and DATA pins. The on board
program/erase connection is shown below.
WHC4403
XTAL
58
Xin1
57
Xout1
55
Vdd
51
Mode
W741E260
1
Vss
Vpp
Data
5
6
7
JP9
Figure 14. The W741E260 Program/Erase Configuration
- 36 -
W741E260
ABSOLUTE MAXIMUM RATINGS
PARAMETER
RATING
UNIT
Supply Voltage to Ground Potential
-0.3 to +7.0
V
Applied Input/Output Voltage
-0.3 to +7.0
V
120
mW
0 to +70
°C
-55 to +150
°C
Power Dissipation
Ambient Operating Temperature
Storage Temperature
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.
DC CHARACTERISTICS
(VDD-VSS = 3.0V, Fm = 4.19 MHz, Fs = 32.768 KHz, Ta = 25° C, LCD on; unless otherwise specified)
PARAMETER
SYM.
CONDITIONS
MIN.
TYP.
MAX.
UNIT
-
2.4
-
5.5
V
Op. Voltage
VDD
Op. Current (Crystal type)
IOP1
No load (Ext-V)
In dual-clock normal
operation
-
0.6
2.5
mA
Op. Current (RC type)
IOP2
No load (Ext-V)
In dual-clock normal
operation
-
1
4
mA
Op. Current (Crystal type)
IOP3
No load (Ext-V)
In dual-clock slow operation
and Fm is stopped
-
8.5
20
µA
Hold Current (Crystal
type)
IHM1
Hold mode No load (Ext-V)
In dual-clock normal
operation
-
280
450
µA
Hold Current (RC type)
IHM2
Hold mode No load (Ext-V)
In dual-clock normal
operation
-
500
600
µA
Hold Current (Crystal
type)
IHM3
Hold mode No load (Ext-V)
In dual-clock slow operation
and Fm is stopped
-
4.0
6
µA
Stop Current (Crystal
type)
ISM1
Stop mode No load (Ext-V)
In dual-clock normal
operation
-
4.0
6
µA
Stop Current (Crystal
type)
ISM2
Stop mode No load (Ext-V)
In single-clock operation
-
0.1
2
µA
Input Low Voltage
VIL
-
VSS
-
0.3
VDD
V
- 37 -
Publication Release Date: March 1998
Revision A2
W741E260
DC Characteristics, continued
PARAMETER
SYM.
CONDITIONS
MIN.
TYP.
MAX.
UNIT
-
0.7
VDD
-
VDD
V
Input High Voltage
VIH
MFP Output Low Voltage
VML
IOL = 3.5 mA
-
-
0.4
V
MFP Output High Voltage
VMH
IOH = 3.5 mA
2.4
-
-
V
Port RA, RB Output Low
Voltage
VABL
IOL = 2.0 mA
-
-
0.4
V
Port RA, RB Output high
Voltage
VABH
IOH = 2.0 mA
2.4
-
-
V
LCD Supply Current
ILCD
All Seg. ON
-
-
6
µA
SEG0-SEG31 Sink
Current
(Used as LCD output)
IOL1
VOL = 0.4V
VLCD = 0.0V
0.4
-
-
µA
SEG0-SEG31 Drive
Current
(Used as LCD output)
IOH1
VOH = 2.4V
VLCD = 3.0V
0.3
-
-
µA
Segment output low
voltage
(Used as DC output)
VSL
IOL = 0.6 mA
-
-
0.4
V
Segment output high
voltage
(Used as DC output)
VSH
IOH = 3 µA
2.4
-
-
V
Port RE Sink Current
IEL
VOL = 0.9V
9
-
-
mA
Port RE Source Current
IEH
VOH = 2.4V
0.4
1.2
-
mA
Input Port Pull-up Resistor
RCD
Port RC, RD
100
350
1000
KΩ
INT Pull-up Resistor
RINT
-
50
250
1000
KΩ
RES Pull-up Resistor
RRES
-
20
100
500
KΩ
VPP Pull-down Resistor
RVPP
VDD = 5V
1.5
2
2.5
MΩ
MODE Pull-down Resistor
RMODE
VDD = 5V
1.5
2
2.5
MΩ
DATA Pull-down Resistor
RDATA
VDD = 5V
50
100
150
KΩ
- 38 -
W741E260
AC CHARACTERISTICS
(VDD-VSS = 3.0V, Ta = 25° C; unless otherwise specified)
PARAMETER
Op. Frequency
SYM.
FOSC
CONDITIONS
MIN.
TYP.
MAX.
RC type
-
-
4000
Crystal type 1 (Option low
speed type)
-
32.768
-
400
-
4190
-
-
10
%
Crystal type 2 (Option
high speed type)
Frequency Deviation by
Voltage Drop for RC
Oscillator
∆f
f
f(3V) − f(2.4V)
f(3V)
UNIT
KHz
Instruction Cycle Time
TI
One machine cycle
-
4/FOSC
-
mS
Reset Active Width
TRAW
FOSC = 32.768 KHz
1
-
-
µS
Interrupt Active Width
TIAW
FOSC = 32.768 KHz
1
-
-
µS
PAD ASSIGNMENT AND POSITIONS
2870 µm
73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58
57
56
55
54
53
52
51
50
49
48
1
2
3
4
5
Y
4840 µ m
6
7
8
9
(0,0)
X
47
10
11
12
13
14
15
16
17
18
19
46
45
44
43
42
41
40
39
20
38
21
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Note: The chip substrate must be connected to system ground (VSS).
- 39 -
Publication Release Date: March 1998
Revision A2
W741E260
PAD NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PAD NAME
RE2
RE3
VSS
VPP
DATA
COM3
COM2
COM1
COM0
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
X
-1227.80
-1227.80
-1227.80
-1223.25
-1234.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
-1227.80
Y
1810.50
1680.50
1550.50
1079.40
656.85
36.20
-93.80
-223.80
-353.80
-483.80
-613.80
-743.80
-873.80
-1003.80
-1133.80
-1263.80
PAD NO.
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
PAD NAME
SEG28
SEG29
SEG30
SEG31
VDD3
VDD2
VDD1
DH2
DH1
MODE
XOUT2
XIN2
VDD
XOUT1
XIN1
17
SEG7
-1227.80
-1393.80
54
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
-1227.80
-1227.80
-1227.80
-1227.80
-975.80
-845.80
-715.80
-585.80
-455.80
-325.80
-195.80
-65.80
64.20
194.20
324.20
454.20
584.20
714.20
844.20
974.20
-1523.80
-1653.80
-1783.80
-1913.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
-2163.80
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
INT
MFP
RA0
RA1
RA2
RA3
RB0
RB1
RB2
RB3
RC0
RC1
RC2
RC3
RD0
RD1
RD2
RD3
RE0
RE1
- 40 -
RES
X
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
1226.20
Y
-1913.80
-1783.80
-1653.80
-1523.80
-1393.80
-1263.80
-1133.80
-1003.80
-873.80
-112.50
640.50
770.50
900.50
1030.50
1160.50
1290.50
1226.20
1420.50
1226.20
1226.20
1226.20
1040.30
910.30
780.30
650.30
520.30
390.30
260.30
130.30
0.30
-129.70
-259.70
-389.70
-519.70
-649.70
-779.70
-909.70
1550.50
1680.50
1810.50
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
2141.70
W741E260
TYPICAL APPLICATION CIRCUIT
Vcc
VDD
RA0
COM0
RA3
COM3
RB0
RB1
RB2
RB3
SEG0
Output Signal
LCD
PANEL
(1/3 Bias
1/4 Duty)
SEG31
RC0
RC1
RC2
RC3
DH1
0.1 uF
DH2
VDD1
VDD2
VDD3
RD0
RD1
RD2
RD3
Connect to capacitor and VDD
to generate LCD voltage
Vcc
RES
0.1 uF
RE0
RE1
RE2
RE3
XOUT1
XIN1
Vcc
XOUT2
MFP
32.768
KHz
XIN2
470 W
VSS
- 41 -
0.1 uF
Publication Release Date: March 1998
Revision A2
W741E260
INSTRUCTION SET TABLE
Symbol Description
ACC:
ACC.n:
WR:
PAGE:
MR0:
MR1:
PM0:
PM1:
PM2:
PSR0:
PSR1:
R:
LCDR:
R.n:
I:
L:
Accumulator
Accumulator bit n
Working Register
Page Register
Mode Register 0
Mode Register 1
Port Mode 0
Port Mode 1
Port Mode 2
Port Status Register 0
Port Status Register 1
Memory (RAM) of address R
LCD data RAM of address LDR
Memory bit n of address R
Constant parameter
Branch or jump address
CF:
ZF:
Carry Flag
Zero Flag
PC:
TM0L:
TM0H:
TM1L:
TM1H:
TABL:
TABH:
IEF.n:
HCF.n:
HEF.n:
SEF.n:
PEF.n:
EVF.n:
Program Counter
Low nibble of the Timer 0 counter
High nibble of the Timer 0 counter
Low nibble of the Timer 1 counter
High nibble of the Timer 1 counter
Low nibble of the look-up table address buffer
High nibble of the look-up table address buffer
Interrupt Enable Flag n
HOLD mode release Condition Flag n
HOLD mode release Enable Flag n
STOP mode wake-up Enable Flag n
Port Enable Flag n
Event Flag n
! =:
&:
^:
EX:
←:
Not equal
AND
OR
Exclusive OR
Transfer direction, result
[PAGE*10H+()]:
[P()]:
Contents of address PAGE(bit2, bit1, bit0)*10H+()
Contents of port P
- 42 -
W741E260
INSTRUCTION SET TABLE 1
Mnemonic
Arithmetic
Function
Flag Affected
Cycle
ADD
R, ACC
ACC←(R) + (ACC)
ZF, CF
1
ADD
WR, #I
ACC←(WR) + I
ZF, CF
1
ADDR
R, ACC
ACC, R←(R) + (ACC)
ZF, CF
1
ADDR
WR, #I
ACC, WR←(WR) + I
ZF, CF
1
ADC
R, ACC
ACC←(R) + (ACC) + (CF)
ZF, CF
1
ADC
WR, #I
ACC←(WR) + I + (CF)
ZF, CF
1
ADCR
R, ACC
ACC, R←(R) + (ACC) + (CF)
ZF, CF
1
ADCR
WR, #I
ACC, WR←(WR) + I + (CF)
ZF, CF
1
ADU
R, ACC
ACC←(R) + (ACC)
ZF
1
ADU
WR, #I
ACC←(WR) + I
ZF
1
ADUR
R, ACC
ACC, R←(R) + (ACC)
ZF
1
ADUR
WR, #I
ACC, W R←(WR) + I
ZF
1
SUB
R, ACC
ACC←(R) - (ACC)
ZF, CF
1
SUB
WR, #I
ACC←(WR) - I
ZF, CF
1
SUBR
R, ACC
ACC, R←(R) - (ACC)
ZF, CF
1
SUBR
WR, #I
ACC, WR←(WR) - I
ZF, CF
1
SBC
R, ACC
ACC←(R) - (ACC) - (CF)
ZF, CF
1
SBC
WR, #I
ACC←(WR) - I - (CF)
ZF, CF
1
SBCR
R, ACC
ACC, R←(R) - (ACC) - (CF)
ZF, CF
1
SBCR
WR, #I
ACC, WR←(WR) - I - (CF)
ZF, CF
1
INC
R
ACC, R←(R) + 1
ZF, CF
1
DEC
R
ACC, R←(R) - 1
ZF, CF
1
- 43 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 1, continued
Mnemonic
Logic Operations
Function
Flag Affected
Cycle
ANL
R, ACC
ACC←(R) & (ACC)
ZF
1
ANL
WR, #I
ACC←(WR) & I
ZF
1
ANLR
R, ACC
ACC, R←(R) & (ACC)
ZF
1
ANLR
W, R #I
ACC, WR←(WR) & I
ZF
1
ORL
R, ACC
ACC←(R) ∧ (ACC)
ZF
1
ORL
WR, #I
ACC←(WR) ∧ I
ZF
1
ORLR
R, ACC
ACC, R←(R) ∧ (ACC)
ZF
1
ORLR
WR, #I
ACC, WR←(WR) ∧ I
ZF
1
XRL
R, ACC
ACC←(R) EX (ACC)
ZF
1
XRL
WR, #I
ACC←(WR) EX I
ZF
1
XRLR
R, ACC
ACC, R←(R) EX (ACC)
ZF
1
XRLR
WR, #I
ACC, WR←(WR) EX I
ZF
1
JMP
L
PC10~PC0←L10~L0
1
JB0
L
PC10~PC0←L10~L0; if ACC.0 = "1"
1
JB1
L
PC10~PC0←L10~L0; if ACC.1 = "1"
1
JB2
L
PC10~PC0←L10~L0; if ACC.2 = "1"
1
JB3
L
PC10~PC0←L10~L0; if ACC.3 = "1"
1
JZ
L
PC10~PC0←L10~L0; if ACC = 0
1
JNZ
L
PC10~PC0←L10~L0; if ACC ! = 0
1
JC
L
PC10~PC0←L10~L0; if CF = "1"
1
JNC
L
PC10~PC0←L10~L0; if CF != "1"
1
DSKZ
R
ACC, R←(R) - 1; skip if ACC = 0
ZF, CF
1
DSKNZ
R
ACC, R←(R) - 1; skip if ACC != 0
ZF, CF
1
SKB0
R
Skip if R.0 = "1"
1
SKB1
R
Skip if R.1 = "1"
1
SKB2
R
Skip if R.2 = "1"
1
SKB3
R
Skip if R.3 = "1"
1
Branch
- 44 -
W741E260
Instruction Set Table 1, continued
Mnemonic
Data Move
Function
Flag Affected
Cycle
MOV
WR, R
WR←(R)
1
MOV
R, WR
R←(WR)
1
MOVA
WR, R
ACC, WR←(R)
ZF
1
MOVA
R, WR
ACC, R←(WR)
ZF
1
MOV
R, ACC
R←(ACC)
MOV
ACC, R
ACC←(R)
MOV
R, #I
R←I
1
MOV
WR, @R
WR←[PR(bit2, bit1, bit0)x10H +(R)]
2
MOV
@R, WR
[PR(bit2, bit1, bit0)x10H +(R)]←WR
2
MOV
TABL, R
TABL←(R)
1
MOV
TABH, R
TABH←(R)
1
MOVC
R
R←[(TABH) × 10H + (TABL)]
2
MOVC
WR, #I
WR ← [(I6 ~ I0) × 10H + (ACC)]
2
1
ZF
1
Input & Output
MOVA
R, RA
ACC, R←[RA]
ZF
1
MOVA
R, RB
ACC, R←[RB]
ZF
1
MOVA
R, RC
ACC, R←[RC]
ZF
1
MOVA
R, RD
ACC, R←[RD]
ZF
1
MOV
RA, R
[RA]←(R)
1
MOV
RB R
[RB]←(R)
1
MOV
RE, R
[RE]←(R)
1
MOV
MFP, #I
[MFP]← I
1
Flag & Register
MOVA
R, PAGE
ACC, R←PAGE (Page Register)
MOV
PAGE, R
PAGE←(R)
1
MOV
MR0, #I
MR0←I
1
MOV
MR1, #I
MR1←I
1
MOV
PAGE, #I
PAGE←I
1
MOVA
R, CF
ACC.0, R.0←CF
ZF
1
MOV
CF, R
CF←(R.0)
CF
1
MOVA
R,HCFL
ACC, R←HCF0~HCF3
ZF
1
MOVA
R,HCFH
ACC, R←HCF4~HCF7
ZF
1
- 45 -
ZF
1
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 1, continued
CLR
Mnemonic
PMF, #I
Function
Clear Parameter Flag if In = 1
Flag Affected
Cycle
1 NOTE 2
SET
PMF, #I
Set Parameter Flag if In = 1
MOV
PM0, #I
Port Mode 0← I
1
MOV
PM1, #I
Port Mode 1← I
1
MOV
PM2, #I
Port Mode 2← I
1
CLR
EVF, #I
Clear Event Flag if In = 1
1
MOV
PEF, #I
Set/Reset Port Enable Flag
1
MOV
IEF, #I
Set/Reset Interrupt Enable Flag
1
MOV
HEF, #I
Set/Reset HOLD mode release
Enable Flag
1
MOV
SEF, #I
Set/Reset STOP mode wake-up
Enable Flag for RC port
1
MOV
SCR, #I
SCR←I
MOVA
R, PSR0
ACC, R←Port Status Register 0
CLR
PSR0
Clear Port Status Register 0
SET
CF
Set Carry Flag
CF
1
CLR
CF
Clear Carry Flag
CF
1
CLR
DIVR0
Clear the last 4-bit of the Divider 0
1
CLR
DIVR1
Clear the last 4-bit of the Divider 1
1 NOTE 1
CLR
WDT
Clear WatchDog Timer
1 NOTE 2
1 NOTE 1
ZF
1
1
1
Shift & Rotate
SHRC
R
ACC.n, R.n←(R.n+1);
ZF, CF
1
ZF, CF
1
ZF, CF
1
ZF, CF
1
ACC.3, R.3←0; CF←R.0
RRC
R
ACC.n, R.n←(R.n+1);
ACC.3, R.3←CF; CF←R.0
SHLC
R
ACC.n, R.n←(R.n-1);
ACC.0, R.0←0; CF←R.3
RLC
R
ACC.n, R.n←(R.n-1);
ACC.0, R.0←CF; CF←R.3
- 46 -
W741E260
Instruction Set Table 1, continued
Mnemonic
Function
Flag Affected
Cycle
LCD
MOV
LCDR, #I
LCDR← I
1
MOV
WR, LCDR
WR←(LCDR)
1
MOV
LCDR, WR
LCDR←(WR)
1
MOV
LCDR, ACC
LCDR←(ACC)
1
MOV
LCDM, #I
Select LCD output mode type
1
LCDON
LCD ON
1
LCDOFF
LCD OFF
1
Timer
MOV
TM0L, R
TM0L←(R)
1
MOV
TM0H, R
TM0H←(R)
1
MOV
TM0, #I
Timer 0 set
1
MOV
TM1L, R
TM1L←(R)
1
MOV
TM1H, R
TM1H←(R)
1
MOV
TM1, #I
Timer 1 set
1
L
STACK ← (PC)+1;
1
Subroutine
CALL
PC10 ~ PC0 ← L10 ~ L0
RTN
(PC)← STACK
1
HOLD
Enter Hold mode
1
STOP
Enter Stop mode
1
NOP
No Operation
1
Other
EN
INT
Enable Interrupt Function
1
DIS
INT
Disable Interrupt Function
1
Note:
1. These instructions are available in W741C260 body, but inhibited in W741C250 body.
2. The bit0, bit1 and bit2 of PMF are reserved in W741C250 and W741C260 body.
- 47 -
Publication Release Date: March 1998
Revision A2
W741E260
INSTRUCTION SET TABLE 2
ADC
R, ACC
Add R to ACC with CF
Machine Code:
0
0
0
0
1
0
0
0
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) + (ACC) + (CF)
Description:
The contents of the data memory location addressed by R6 to R0, ACC, and
CF are binary added and the result is loaded into the ACC.
Flag Affected:
CF & ZF
ADC
Add immediate data to WR with CF
WR, #I
Machine Code:
0
0
0
0
1
1
0
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) + I + (CF)
Description:
The contents of the Working Register (WR), I and CF are binary added and
the result is loaded into the ACC.
Flag Affected:
CF & ZF
ADCR R, ACC
Add R to ACC with CF
Machine Code:
0
0
0
0
1
0
0
1
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) + (ACC) + (CF)
Description:
The contents of the data memory location addressed by R6 to R0, ACC, and
CF are binary added and the result is placed in the ACC and the data
memory.
Flag Affected:
CF & ZF
- 48 -
W741E260
Instruction Set Table 2, continued
ADCR
WR, #I
Add immediate data to WR with CF
Machine Code:
0
0
0
0
1
1
0
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) + I + (CF)
Description:
The contents of the Working Register (WR), I, CF are binary added and the
result is placed in the ACC and the WR.
Flag Affected:
CF & ZF
ADD
Add R to ACC
R, ACC
Machine Code:
0
0
0
1
1
0
0
0
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) + (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and ACC
are binary added and the result is loaded into the ACC.
Flag Affected:
CF & ZF
ADD
Add immediate data to WR
WR, #I
Machine Code:
0
0
0
1
1
1
0
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) + I
Description:
The contents of the Working Register (WR) and the immediate data I are
binary added and the result is loaded into the ACC.
Flag Affected:
CF & ZF
- 49 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
ADDR
R, ACC
Add R to ACC
Machine Code:
0
0
0
1
1
0
0
1
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) + (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and ACC
are binary added and the result is placed in the ACC and the data memory.
Flag Affected:
CF & ZF
ADDR
Add immediate data to WR
WR, #I
Machine Code:
0
0
0
1
1
1
0
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) + I
Description:
The contents of the Working Register (WR) and the immediate data I are
binary added and the result is placed in the ACC and the WR.
Flag Affected:
CF & ZF
ADU
Add R to ACC and Carry Flag unchange
R, ACC
Machine Code:
0
0
1
0
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) + (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and ACC
are binary added and the result is loaded into the ACC.
Flag Affected:
ZF
- 50 -
W741E260
Instruction Set Table 2, continued
ADU
WR, #I
Add immediate data to WR and Carry Flag unchange
Machine Code:
0
0
1
0
1
1
0
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) + I
Description:
The contents of the Working Register (WR) and the immediate data I are
binary added and the result is loaded into the ACC.
Flag Affected:
ZF
ADUR
Add R to ACC and Carry Flag unchange
R, ACC
Machine Code:
0
0
1
0
1
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) + (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and ACC
are binary added and the result is placed in the ACC and the data memory.
Flag Affected:
ZF
ADUR
Add immediate data to WR and Carry Flag unchange
WR, #I
Machine Code:
0
0
1
0
1
1
0
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) + I
Description:
The contents of the Working Register (WR) and the immediate data I are
binary added and the result is placed in the WR and the ACC.
Flag Affected:
ZF
- 51 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
ANL
R, ACC
And R to ACC
Machine Code:
0
0
1
0
1
0
1
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) & (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are ANDed and the result is loaded into the ACC.
Flag Affected:
ZF
ANL
And immediate data to WR
WR, #I
Machine Code:
0
0
1
0
1
1
1
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) & I
Description:
The contents of the Working Register (WR) and the immediate data I are
ANDed and the result is loaded into the ACC.
Flag Affected:
ZF
ANLR
And R to ACC
R, ACC
Machine Code:
0
0
1
0
1
0
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) & (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are ANDed and the result is placed in the data memory and the ACC.
Flag Affected:
ZF
- 52 -
W741E260
Instruction Set Table 2, continued
ANLR
WR, #I
And immediate data to WR
Machine Code:
0
0
1
0
1
1
1
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) & I
Description:
The contents of the Working Register (WR) and the immediate data I are
ANDed and the result is placed in the WR and the ACC.
Flag Affected:
ZF
CALL
Call subroutine
L
Machine Code:
0
1
1
0
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
STACK ← (PC)+1;
PC10 ~ PC0 ← L10 ~ L0
Description:
The next program counter (PC10 to PC0) is saved in the STACK and then
the direct address (L10 to L0) is loaded into the program counter.
A subroutine is called.
CLR
Clear CF
CF
Machine Code:
0
1
0
1
0
0
Machine Cycle:
1
Operation:
Clear CF
Description:
Clear Carry Flag to 0.
Flag Affected:
CF
0
0
- 53 -
0
0
0
0
0
0
0
0
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
CLR
DIVR0
Reset the last 4 bits of the DIVideR 0
Machine Code:
0
0
0
1
0
1
1
1
0
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Reset the last 4 bits of the divider 0
Description:
When this instruction is executed, the last 4 bits of the divider 0 (14 bits) are
reset.
CLR
Reset the last 4 bits of the DIVideR 1
DIVR1
Machine Code:
0
1
0
1
0
1
0
1
1
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Reset the last 4 bits of the divider 1
Description:
When this instruction is executed, the last 4 bits of the divider 1 (14 bits) are
reset. This instruction is available in W741C260 body, but it is inhibited in
W741C250 body.
CLR
Clear ParaMeter Flag
PMF, #I
Machine Code:
0
0
0
1
0
1
1
Machine Cycle:
1
Operation:
Clear Parameter Flag
Description:
Description of each flag:
0
1
0
0
0
I3
I2
I1
I0, I1, I2 : Reserved
I3 = 1 : The input clock of the watchdog timer is Fosc/1024.
- 54 -
I0
W741E260
Instruction Set Table 2, continued
CLR
EVF, #I
Clear EVent Flag
Machine Code:
0
1
0
0
0
0
0
0
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Clear event flag
Description:
The condition corresponding to the data specified by I7 to I0 is controlled.
CLR
PSR0
I0~I7
Mode after execution of instruction
I0 = 1
EVF0 caused by overflow from the divider 0 is reset.
I1 = 1
EVF1 caused by underflow from the timer 0 is reset.
I2 = 1
EVF2 caused by the signal change at port RC is reset.
I3
Reserved
I4 = 1
EVF4 caused by overflow from the divider 1 is reset for W741C260 body;
EVF4 caused by the falling edge signal on INT pin is reset for W741C250 body.
I5 & I6
Reserved
I7 = 1
EVF7 caused by underflow from the timer 1 is reset.
Clear Port Status Register 0 (RC port signal change flag)
Machine Code:
0
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Clear Port Status Register 0 (RC port signal change flag)
Description:
When this instruction is executed, the RC port signal change flag (PSR0) is
cleared.
CLR
Reset the last 4 bits of the WatchDog Timer
WDT
Machine Code:
0
0
0
1
0
1
1
1
1
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Reset the last 4 bits of the watchdog timer
Description:
When this instruction is executed, the last 4 bits of the watchdog timer are
reset.
- 55 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
DEC
R
Decrement R content
Machine Code:
0
1
0
0
1
0
1
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) - 1
Description:
Decrement the data memory content and load result into the ACC and the
data memory.
Flag Affected:
CF & ZF
DIS
Disable Interrupt function
INT
Machine Code:
0
1
0
1
0
0
0
0
1
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Disable interrupt function
Description:
Interrupt function is inhibited by executing this instruction.
DSKNZ
Decrement R content then skip if ACC ! = 0
R
Machine Code:
0
1
0
0
1
0
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) - 1;
PC ← (PC) + 2 if ACC ! = 0
Description:
Decrement the data memory content and load result into the ACC and the
data memory. If ACC ! = 0, the program counter is incremented by 2 and
produces a skip.
Flag Affected:
CF & ZF
- 56 -
W741E260
Instruction Set Table 2, continued
DSKZ
R
Decrement R content then skip if ACC is zero
Machine Code:
0
1
0
0
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) - 1;
PC ← (PC) + 2 if ACC = 0
Description:
Decrement the data memory content and load result into the ACC and the
data memory. If ACC = 0, the program counter is incremented by 2 and
produces a skip.
Flag Affected:
CF & ZF
EN
Enable Interrupt function
INT
Machine Code:
0
1
0
1
0
0
0
0
1
1
0
0
Machine Cycle:
1
Operation:
Enable interrupt function
Description:
This instruction enables the interrupt function.
HOLD
Enter the HOLD mode
Machine Code:
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
Enter the HOLD mode
Description:
The following two conditions cause the HOLD mode to be released.
(1) An interrupt is accepted.
(2) The HOLD release condition specified by the HEF is met.
In HOLD mode, when an interrupt is accepted the HOLD mode will be
released and the interrupt service routine will be executed. After completing
the interrupt service routine by executing the RTN instruction, the µC will
enter HOLD mode again.
- 57 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
INC
R
Increment R content
Machine Code:
0
1
0
0
1
0
1
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) + 1
Description:
Increment the data memory content and load the result into the ACC and
the data memory.
Flag Affected:
CF & ZF
JB0
Jump when bit 0 of ACC is "1"
L
Machine Code:
1
0
0
0
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC.0 = "1"
Description:
If bit 0 of the ACC is "1," PC10 to PC0 of the program counter are replaced
with the data specified by L10 to L0 and a jump occurs. If bit 0 of the ACC is
"0," the program counter (PC) is incremented.
JB1
Jump when bit 1 of ACC is "1"
L
Machine Code:
1
0
0
1
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC.1 = "1"
Description:
If bit 1 of the ACC is "1," PC10 to PC0 of the program counter are replaced
with the data specified by L10 to L0 and a jump occurs. If bit 1 of the ACC is
"0," the program counter (PC) is incremented.
- 58 -
W741E260
Instruction Set Table 2, continued
JB2
L
Jump when bit 2 of ACC is "1"
Machine Code:
1
0
1
0
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC.2="1"
Description:
If bit 2 of the ACC is "1," PC10 to PC0 of the program counter are replaced
with the data specified by L10 to L0 and a jump occurs. If bit 2 of the ACC is
"0," the program counter (PC) is incremented.
JB3
Jump when bit 3 of ACC is "1"
L
Machine Code:
1
0
1
1
0
L10 L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC.3 = "1"
Description:
If bit 3 of the ACC is "1," PC10 to PC0 of the program counter are replaced
with the data specified by L10 to L0 and a jump occurs. If bit 3 of the ACC is
"0," the program counter (PC) is incremented.
JC
Jump when CF is "1"
L
Machine Code:
1
1
1
1
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if CF = "1"
Description:
If CF is "1," PC10 to PC0 of the program counter are replaced with the data
specified by L10 to L0 and a jump occurs. If the CF is "0," the program
counter (PC) is incremented.
- 59 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
JMP
L
Jump absolutely
Machine Code:
0
1
1
1
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0
Description:
PC10 to PC0 of the program counter are replaced with the data specified by
L10 to L0 and an unconditional jump occurs.
JNC
Jump when CF is not "1"
L
Machine Code:
1
1
0
1
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if CF = "0"
Description:
If CF is "0," PC10 to PC0 of the program counter are replaced with the data
specified by L10 to L0 and a jump occurs. If CF is "1," the program counter
(PC) is incremented.
JNZ
Jump when ACC is not zero
L
Machine Code:
1
1
0
0
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC ! = 0
Description:
If the ACC is not zero, PC10 to PC0 of the program counter are replaced
with the data specified by L10 to L0 and a jump occurs. If the ACC is zero,
the program counter (PC) is incremented.
- 60 -
W741E260
Instruction Set Table 2, continued
JZ
L
Jump when ACC is zero
Machine Code:
1
1
1
0
0
L10
L9
L8
L7
L6
L5
L4
L3
L2
L1
L0
Machine Cycle:
1
Operation:
PC10 ~ PC0 ← L10 ~ L0; if ACC = 0
Description:
If the ACC is zero, PC10 to PC0 of the program counter are replaced with
the data specified by L10 to L0 and a jump occurs. If the ACC is not zero,
the program counter (PC) is incremented.
LCDON
LCD ON
Machine Code:
0
0
0
0
0
0
Machine Cycle:
1
Operation:
LCD ON
Description:
Turn on LCD display.
LCDOFF
LCD OFF
Machine Code:
0
0
0
0
0
0
Machine Cycle:
1
Operation:
LCD OFF
Description:
Turn off LCD display.
1
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
- 61 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
ACC, R
Move R content to ACC
Machine Code:
0
1
0
0
1
1
1
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the ACC.
Flag Affected:
ZF
MOV
Move R.0 content to CF
CF, R
Machine Code:
0
1
0
1
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
CF ← (R.0)
Description:
The bit 0 content of the data memory location addressed by R6 to R0 is
loaded into CF.
Flag Affected:
CF
- 62 -
W741E260
Instruction Set Table 2, continued
MOV
HEF, #I
Set/Reset Hold mode release Enable Flag
Machine Code:
0
1
0
0
0
0
0
1
I7
Machine Cycle:
1
Operation:
Hold mode release enable flag control
Description:
I6
I5
I4
I3
I2
I1
I0
I0~I7
Operation
I0 = 1
The HEF0 is set so that overflow from the divider 0 caused
the HOLD mode to be released.
I1 = 1
The HEF1 is set so that underflow from the Timer 0 caused
the HOLD mode to be released.
I2 = 1
The HEF2 is set so that signal change at port RC caused
the HOLD mode to be released.
I3
Reserved
I4 = 1
The HEF4 is set so that overflow from the divider 1 caused
the HOLD mode to be released for W741C260 body;
The HEF4 is set so that the falling edge signal at the INT pin
caused the HOLD mode to be released for W741C250 body.
I5 & I6
Reserved
I7 = 1
The HEF7 is set so that underflow from the Timer 1 caused
the HOLD mode to be released.
- 63 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
IEF, #I
Set/Reset Interrupt Enable Flag
Machine Code:
0
1
0
1
0
0
0
1
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Interrupt Enable flag Control
Description:
The interrupt enable flag corresponding to the data specified by I7-I0 is
controlled:
I0~I7
Operation
I0 = 1
The IEF0 is set so that interrupt 0 (overflow from the
divider 0) is accepted.
I1 = 1
The IEF1 is set so that interrupt 1 (underflow from the
Timer 0) is accepted.
I2 = 1
The IEF2 is set so that interrupt 2 (signal change at port
RC) is accepted.
Reserved
I3
MOV
LCDM, #I
I4 = 1
The IEF4 is set so that interrupt 4 (overflow from the
divider 1) is accepted for W741C260 body;
the IEF4 is set so that interrupt 4 (falling edge signal
at the INT pin) is accepted for the W741C250 body.
I5 & I6
Reserved
I7 = 1
The IEF7 is set so that interrupt 7 (underflow from the
Timer 1) is accepted.
Select LCD output Mode type
Machine Code:
0
0
0
0
0
0
1
1
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Select LCD output mode type
Description:
When LCD output pins are set to DC output mode, user can select CMOS
or NMOS as output type.
I0~I7 = 0 => CMOS type; I0~I7 = 1 => NMOS type.
- 64 -
W741E260
Instruction Set Table 2, continued
MOV
LCDR, ACC
Move ACC content to LCDR
Machine Code:
0
0
0
0
0
1
1
D4
D3 D2 D1 D0
0
0
0
0
Machine Cycle:
1
Operation:
LCDR ← (ACC)
Description:
The contents of the ACC are loaded to the LCD data RAM (LCDR) location
addressed by D4 to D0.
MOV
Load WR content to LCDR
LCDR, WR
Machine Code:
0
1
0
0
0
1
0
D4
D3 D2 D1 D0 W3 W2 W1 W0
Machine Cycle:
1
Operation:
LCDR ← (WR)
Description:
The contents of the WR are loaded to the LCD data RAM (LCDR) location
addressed by D4 to D0.
MOV
Load immediate data to LCDR
LCDR, #I
Machine Code:
0
0
0
0
0
1
0
D4
D3 D2 D1 D0 I3
I2
I1
I0
Machine Cycle:
1
Operation:
LCDR ← I
Description:
The immediate data I are loaded to the LCD data RAM (LCDR) location
addressed by D4 to D0.
- 65 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
MFP, #I
Modulation Frequency Pulse generator
Machine Code:
0
0
0
1
0
0
1
0
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
[MFP] ← I
Description:
If the bit 2 of MR1 is "0," the waveform specified by I7 to I0 is delivered at
the MFP output pin (MFP). The relation between the waveform and
immediate data I is as follows:
I5~I0
I0 = 1
I1 = 1
I2 = 1
I3 = 1
Signal
Fosc
256
Fosc
512
Fosc
4096
Fosc
8192
I7
I6
Signal
0
0
Low
0
1
High
1
0
Fosc/16
1
1
Fosc/8
- 66 -
I4 = 1
Fosc
16384
I5 = 1
Fosc
32768
W741E260
Instruction Set Table 2, continued
MOV
MR0, #I
Load immediate data to Mode Register 0 (MR0)
Machine Code:
0
0
0
1
0
0
1
1
1
0
0
Machine Cycle:
1
Operation:
MR0 ← I
Description:
The immediate data I are loaded to the MR0.
0
I3
I2
I1
I0
MR0 bits description:
bit 0
= 0 The fundamental frequency of Timer 0 is Fosc/4
= 1 The fundamental frequency of Timer 0 is Fosc/1024
bit 1
Reserved
bit 2
Reserved
bit 3
= 0 Timer 0 stop down-counting
= 1 Timer 0 start down-counting
- 67 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
MR1, #I
Load immediate data to Mode Register 1 (MR1)
Machine Code:
0
0
0
1
0
0
1
1
0
0
0
Machine Cycle:
1
Operation:
MR1 ← I
Description:
The immediate data I are loaded to the MR1.
MR1 bit description:
0
I3
I2
I1
I0
bit0
= 0 The internal fundamental frequency of Timer 1 is Fosc
= 1 The internal fundamental frequency of Timer 1 is Fosc/64
bit1
= 0 The fundamental frequency source of Timer 1 is
internal clock
= 1 The fundamental frequency source of Timer 1 is
external clock via RC.0 input pin
bit2
= 0 The specified waveform of the MFP generator is
delivered at the MFP output pin
= 1 The specified frequency of the Timer 1 is delivered at
the MFP output pin
bit3
= 0 Timer 1 stop down-counting
= 1 Timer 1 start down-counting
- 68 -
W741E260
Instruction Set Table 2, continued
MOV PAGE, #I
Load immediate data to Page Register
Machine Code:
0
1
0
1
0
1
1
0
1
0
0
0
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Page Register ← I
Description:
The immediate data I are loaded to the PR.
Bit 3 is reserved.
Bit 0, bit 1, and bit 2 indirect addressing mode preselect bits:
bit2
bit1
bit0
0
0
0
= Page 0 (00H~0FH)
0
0
1
= Page 1 (10H~1FH)
0
1
0
= Page 2 (20H~2FH)
0
1
1
= Page 3 (30H~3FH)
1
0
0
= Page 4 (40H~4FH)
1
0
1
= Page 5 (50H~5FH)
1
1
0
= Page 6 (60H~6FH)
1
1
1
= Page 7 (70H~7FH)
- 69 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
PEF, #I
Set/Reset Port Enable Flag
Machine Code:
0
1
0
0
0
0
1
1
0
0
0
0
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Port enable flag control
Description:
The data specified by I can cause HOLD mode to be released or an
interrupt to occur. The signal change on port RC is specified.
I0~I7
MOV PM0, #I
Signal change at port RC
I0 = 1
RC0
I1 = 1
RC1
I2 = 1
RC2
I3 = 1
RC3
Set/Reset Port Mode 0 register
Machine Code:
0
1
0
1
0
0
1
1
0
0
0
0
I3
I2
I1
Machine Cycle:
1
Operation:
Set/Reset Port mode 0 register
Description:
I0 = 0: RA port is CMOS type; I0 = 1: RA port is NMOS type.
I1 = 0: RB port is CMOS type; I1 = 1: RB port is NMOS type.
I2 = 0: RC port pull-high resistor is disabled;
I2 = 1: RC port pull-high resistor is enabled.
I3 = 0: RD port pull-high resistor is disabled;
I3 = 1: RD port pull-high resistor is enabled.
- 70 -
I0
W741E260
Instruction set table 2, continued
MOV PM1, #I
RA port independent Input/Output control
Machine Code:
0
1
0
1
0
1
1
1
0
0
0
0
I3
I2
Machine Cycle:
1
Operation:
RA port 4 pins input/output control is independent.
Description:
I0 = 0: RA.0 is output pin; I0 = 1: RA.0 is input pin.
I1 = 0: RA.1 is output pin; I1 = 1: RA.1 is input pin.
I2 = 0: RA.2 is output pin; I2 = 1: RA.2 is input pin.
I3 = 0: RA.3 is output pin; I3 = 1: RA.3 is input pin.
Default condition RA port is input mode (PM = 1111B).
MOV PM2, #I
RB port independent Input/Output control
Machine Code:
0
1
0
1
0
1
1
1
1
0
0
0
I3
I2
Machine Cycle:
1
Operation:
RB port 4 pins input/output control is independent.
Description:
I0 = 0: RB.0 is output pin; I0 = 1: RB.0 is input pin.
I1 = 0: RB.1 is output pin; I1 = 1: RB.1 is input pin.
I2 = 0: RB.2 is output pin; I2 = 1: RB.2 is input pin.
I3 = 0: RB.3 is output pin; I3 = 1: RB.3 is input pin.
Default condition RB port is input mode (PM2 = 1111B).
- 71 -
I1
I0
I1
I0
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
R, ACC
Move ACC content to R
Machine Code:
0
1
0
1
1
0
0
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
R ← (ACC)
Description:
The contents of the ACC are loaded to the data memory location addressed
by R6 to R0.
MOVA R, RA
Input RA port data to ACC & R
Machine Code:
0
1
0
1
1
0
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC , R ← [RA]
Description:
The data on port RA are loaded into the data memory location addressed by
R6 to R0 and the ACC.
Flag Affected:
ZF
MOVA
Input RB port data to ACC & R
R, RB
Machine Code:
0
1
0
1
1
0
1
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC , R ← [RB]
Description:
The data on port RB are loaded into the data memory location addressed by
R6 to R0 and the ACC.
Flag Affected:
ZF
- 72 -
W741E260
Instruction Set Table 2, continued
MOVA R, RC
Input RC port data to ACC & R
Machine Code:
0
1
0
0
1
0
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC , R ← [RC]
Description:
The input data on the input port RC are loaded into the data memory
location addressed by R6 to R0 and the ACC.
Flag Affected:
ZF
MOVA R, RD
Input RD port data to ACC & R
Machine Code:
0
1
0
0
1
0
1
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC , R ← [RD]
Description:
The input data on the input port RD are loaded into the data memory
location addressed by R6 to R0 and the ACC.
Flag Affected:
ZF
MOV
Move WR content to R
R, WR
Machine Code:
1
1
1
1
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
R ← (WR)
Description:
The contents of the WR are loaded to the data memory location addressed
by R6 to R0.
- 73 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
R, #I
Load immediate data to R
Machine Code:
1
0
1
1
1
I3
I2
I1
I0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
R←I
Description:
The immediate data I are loaded to the data memory location addressed by
R6 to R0.
MOV
Output R content to RA port
RA, R
Machine Code:
0
1
0
1
1
0
1
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
[RA] ← (R)
Description:
The data in the data memory location addressed by R6 to R0 are output to
the port RA.
MOV
Output R content to RB port
RB, R
Machine Code:
Machine Cycle:
Operation:
Description:
MOV
RE, R
0
1
0
1
1
0
1
0
1
R6 R5 R4 R3 R2 R1 R0
6
1
[RB] ← (R)
The contents of the data memory location addressed by R6 to R0 are output
to the port RB.
Output R content to port RE
Machine Code:
0
1
0
1
1
1
1
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
[RE] ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are output
to port RE.
- 74 -
W741E260
Instruction Set Table 2, continued
MOV SCR, #I
System Clock Register control
Machine Code:
0
1
0
1
0
1
0
0
0
0
0
0
I3
I2
I1
I0
Machine Cycle:
1
Operation:
System clock control
Description:
If the operation mode is the dual clock operation selected by the option
codes, the system clock and oscillator can be arranged by controlling the
system clock register. This command is just for the W741C260 body.
SCR bits decription:
MOV SEF, #I
Bit 0
= 0, Fosc=Fm
= 1, Fosc=Fs
Bit 1
= 0, main oscillator is enabled
= 1, main oscillator is disabled
Bit 2
Reserved
Bit 3
= 0, divider 1 is 14-stage
= 1, divider 1 is 13-stage
Set/Reset STOP mode waked-up Enable Flag for port RC
Machine Code:
0
1
0
1
0
0
1
0
0
0
0
0
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Set/reset STOP mode wake-up enable flag for port RC
Description:
The data specified by I cause a wake-up from the STOP mode. The fallingedge signal on port RC can be specified independently.
I0~I7
Falling edge signal at port RC
I0 = 1
RC0
I1 = 1
RC1
I2 = 1
RC2
I3 = 1
RC3
- 75 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV TM0, #I
Timer 0 set
Machine Code:
0
0
0
1
0
0
0
0
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Timer 0 set
Description:
The data specified by I7 to I0 is loaded to the Timer 0 to start the timer.
MOV TM0L, R
Move R content to TM0L
Machine Code:
0
0
0
1
0
1
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TM0L ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TM0L.
MOV TM0H, R
Move R content to TM0H
Machine code:
0
0
0
1
0
1
0
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TM0H ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TM0H.
MOV TM1, #I
Timer 1 set
Machine Code:
0
0
0
1
0
0
0
1
I7
I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Timer 1 set
Description:
The data specified by I7 to I0 is loaded to the Timer 1 to start the timer.
- 76 -
W741E260
Instruction Set Table 2, continued
MOV TM1L, R
Move R content to TM1L
Machine Code:
0
0
0
1
0
1
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TM1L ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TM1L.
MOV TM1H, R
Move R content to TM1H
Machine code:
0
0
0
1
0
1
0
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TM1H ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TM1H.
MOV WR, LCDR
Load LCDR content to WR
Machine Code:
0
1
0
0
0
1
1
D4
D3 D2 D1 D0 W3 W2 W1 W0
Machine Cycle:
1
Operation:
WR ← (LCDR)
Description:
The contents of the LCD data RAM location addressed by D4 to D0 are
loaded to the WR.
MOV
Move R content to WR
WR, R
Machine Code:
1
1
1
0
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
WR ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded to the WR.
- 77 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV
WR, @R
Indirect load from R to WR
Machine Code:
1
1
0
0
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
2
Operation:
WR ← [PR (bit2, bit1, bit0) × 10H + (R)]
Description:
The data memory contents of address [PR (bit2, bit1, bit0) × 10H + (R)] are
loaded to the WR.
MOV
Indirect load from WR to R
@R, WR
Machine Code:
1
1
0
1
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
2
Operation:
[PR (bit2, bit1, bit0) × 10H + (R)] ← WR
Description:
The contents of the WR are loaded to the data memory location addressed
by [PR (bit2, bit1, bit0) × 10H + (R)] .
MOV PAGE, R
Move R content to Page Register
Machine Code:
0
1
0
1
1
1
1
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
PR ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded to the PR.
- 78 -
W741E260
Instruction Set Table 2, continued
MOVA
R, CF
Move CF content to ACC.0 & R.0
Machine Code:
0
1
0
1
1
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC.0, R.0 ← (CF)
Description:
The content of CF is loaded to bit 0 of the data memory location addressed
by R6 to R0 and the ACC. The other bits of the data memory and ACC are
reset to "0."
Flag Affected:
ZF
MOVA R, HCFH
Move HCF4~7 to ACC & R
Machine Code:
0
1
0
0
1
0
0
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← HCF4~7
Description:
The contents of HCF bit 4 to bit 7 (HCF4 to HCF7) are loaded to the data
memory location addressed by R6 to R0 and the ACC. The ACC contents
and the meaning of the bits after execution of this instruction are as follows:
Flag Affected:
Bit 0
HCF4: "1" when the HOLD mode is released by overflow from Divide r 1 for
the W741C260 body;
HCF4: "1" when the HOLD mode is released by the falling edge signal at the
INT pin for the W741C250 body.
Bit 1
HCF7: "1" when the HOLD mode is released by underflow from Timer 1.
Bit 2
Reserved.
Bit 3
Reserved.
ZF
- 79 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOVA R, HCFL
Move HCF0~3 to ACC & R
Machine Code:
0
1
0
0
1
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← HCF0~3
Description:
The contents of HCF bit 0 to bit 3 (HCF0 to HCF3) are loaded to the data
memory location addressed by R6 to R0 and the ACC. The ACC contents
and the meaning of the bits after execution of this instruction are as follows:
Bit 0
HCF0: "1" when the HOLD mode is released by
overflow from the Divider 0.
Bit 1
HCF1: "1" when the HOLD mode is released by
underflow from Timer 0.
Bit 2
HCF2: "1" when the HOLD mode is released by
a signal change on port RC.
Bit 3
Reserved.
Flag Affected:
ZF
MOVA R, PAGE
Move Page Register content to ACC & R
Machine Code:
0
1
0
1
1
1
1
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC , R ← (Page Register)
Description:
The contents of the Page Register (PR) are loaded to the data memory
location addressed by R6 to R0 and the ACC.
Flag Affected:
ZF
- 80 -
W741E260
Instruction Set Table 2, continued
MOVA R, PSR0
Move Port Status Register 0 content to ACC & R
Machine Code:
0
1
0
0
1
1
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← RC port signal change flag (PSR0)
Description:
The contents of the RC port signal change flag (PSR0) are loaded to the
data memory location addressed by R6 to R0 and the ACC. When the signal
changes on any pin of the RC port, the corresponding signal change flag
should be set to 1. Otherwise, it should be 0.
Flag Affected:
ZF
MOVA
Move WR content to ACC & R
R, WR
Machine Code:
0
1
1
1
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (WR)
Description:
The contents of the WR are loaded to the ACC and the data memory
location addressed by R6 to R0.
Flag Affected:
ZF
MOVA
Move R content to ACC & WR
WR, R
Machine Code:
0
1
1
0
1
W3
W2
W1
W0 R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, WR ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded to the WR and the ACC.
Flag Affected:
ZF
- 81 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
MOV TABL, R
Move R content to TABL
Machine Code:
1
0
0
1
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TABL ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TABL.
MOV TABH, R
Move R content to TABH
1
Machine code:
0
0
1
1
0
0
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
TABH ← (R)
Description:
The contents of the data memory location addressed by R6 to R0 are
loaded into the TABH.
MOVC R
Move look-up table ROM addressed by TABL and TABH to R
1
Machine code:
0
0
1
1
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
2
Operation:
WR ← [(TABH) × 10H + (TABL)]
Description:
The contents of the look-up table ROM location addressed by TABH and
TABL are loaded to R.
- 82 -
W741E260
Instruction Set Table 2, continued
MOVC WR, #I
Move look-up table ROM addressed by #I and ACC to WR
1
Machine code:
0
1
0
1
W3 W2 W1
W0 I6
I5
I4
I3
I2
I1
I0
Machine Cycle:
2
Operation:
WR ← [(I6 ~ I0) × 10H + (ACC)]
Description:
The contents of the look-up table ROM location addressed by I6 to I0 and
the ACC are loaded to R.
NOP
No Operation
0
Machine Code:
0
0
0
Machine Cycle:
1
Operation:
No Operation
ORL
OR R to ACC
R, ACC
0
Machine Code:
0
1
1
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) ∧ (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are ORed and the result is loaded into the ACC.
Flag Affected:
ZF
- 83 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
ORL
WR , #I
OR immediate data to WR
Machine Code:
0
0
1
1
1
1
1
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) ∧ I
Description:
The contents of the Working Register (WR) and the immediate data I are
ORed and the result is loaded into the ACC.
Flag Affected:
ZF
ORLR R, ACC
OR R to ACC
Machine Code:
0
0
1
1
1
0
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) ∧ (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are ORed and the result is placed in the data memory and the ACC.
Flag Affected:
ZF
ORLR WR , #I
OR immediate data to WR
0
Machine Code:
0
1
1
1
1
1
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) ∧ I
Description:
The contents of the Working Register(WR) and the immediate data I are
ORed and the result is placed in the WR and the ACC.
Flag Affected:
ZF
- 84 -
W741E260
Instruction Set Table 2, continued
RLC
R
Rotate Left R with CF
Machine Code:
0
1
0
0
1
1
0
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC.n, R.n ← (R.n-1); ACC.0, R.0 ← CF; CF ← R.3
Description:
The contents of the ACC and the data memory location addressed by R6 to
R0 are rotated left one bit, bit 3 is rotated into CF, and CF rotated into bit 0
(LSB). The same contents are loaded into the ACC.
Flag Affected:
CF & ZF
RRC
Rotate Right R with CF
R
Machine Code:
0
1
0
0
1
1
0
1
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC.n, R.n ← (R.n+1); ACC.3, R.3 ← CF; CF ← R.0
Description:
The contents of the ACC and the data memory location addressed by R6 to
R0 are rotated right one bit, bit 0 is rotated into CF, and CF is rotated into bit
3 (MSB). The same contents are loaded into the ACC.
Flag Affected:
CF & ZF
RTN
Return from subroutine
Machine Code:
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
Machine Cycle:
1
Operation:
(PC) ← STACK
Description:
The program counter (PC10 to PC0) is restored from the stack. A return
from a subroutine occurs.
- 85 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
SBC
R, ACC
Subtract ACC from R with Borrow
Machine Code:
0
0
0
0
1
0
1
0
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) - (ACC) - (CF)
Description:
The contents of the ACC and CF are binary subtracted from the contents of
the data memory location addressed by R6 to R0 and the result is loaded
into the ACC.
Flag Affected:
CF & ZF
SBC
Subtract immediate data from WR with Borrow
WR, #I
Machine Code:
0
0
0
0
1
1
1
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) - I - (CF)
Description:
The immediate data I and CF are binary subtracted from the contents of the
WR and the result is loaded into the ACC.
Flag Affected:
CF & ZF
SBCR R, ACC
Subtract ACC from R with Borrow
Machine Code:
0
0
0
0
1
0
1
1
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) - (ACC) - (CF)
Description:
The contents of the ACC and CF are binary subtracted from the contents of
the data memory location addressed by R6 to R0 and the result is placed in
the ACC and the data memory.
Flag Affected:
CF & ZF
- 86 -
W741E260
Instruction Set Table 2, continued
SBCR
WR, #I
Subtract immediate data from WR with Borrow
Machine Code:
0
0
0
0
1
1
1
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, R ← (WR) - I - (CF)
Description:
The immediate data I and CF are binary subtracted from the contents of the
WR and the result is placed in the ACC and the WR.
Flag Affected:
CF & ZF
SET
Set CF
CF
Machine Code:
0
1
0
1
0
Machine Cycle:
1
Operation:
Set CF
Description:
Set Carry Flag to 1.
Flag Affected:
CF
SET
Set ParaMeter Flag
PMF, #I
Machine Code:
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
I3
I2
I1
I0
Machine Cycle:
1
Operation:
Set Parameter Flag
Description:
Description of each flag:
I0, I1, I2 : Reserved
I3 = 1 : The input clock of the watchdog timer is Fosc/16384.
- 87 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
SHLC
R
SHift Left R with CF and LSB = 0
Machine Code:
0
1
0
0
1
1
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC.n, R.n ← (R.n-1); ACC.0, R.0 ← 0; CF ← R.3
Description:
The contents of the ACC and the data memory location addressed by R6 to
R0 are shifted left one bit, but bit 3 is shifted into CF, and bit 0 (LSB) is
replaced with "0." The same contents are loaded into the ACC.
Flag Affected:
CF & ZF
SHRC
SHift Right R with CF and MSB = 0
R
Machine Code:
0
1
0
0
1
1
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC.n, R.n ← (R.n+1); ACC.3, R.3 ← 0; CF ← R.0
Description:
The contents of the ACC and the data memory location addressed by R6 to
R0 are shifted right one bit, but bit 0 is shifted into CF, and bit 3 (MSB) is
replaced with "0." The same contents are loaded into the ACC.
Flag Affected:
CF & ZF
SKB0
If bit 0 of R is equal to 1 then skip
R
Machine Code:
1
0
0
0
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
PC ← (PC) + 2; if R.0 = 1“1”
Description:
If bit 0 of R is equal to 1, the program counter is incremented by 2 and a
skip is produced. If bit 0 of R is not equal to 1, the program counter (PC) is
incremented.
- 88 -
W741E260
Instruction Set Table 2, continued
SKB1
R
If bit 1 of R is equal to 1 then skip
Machine Code:
1
0
0
0
1
0
0
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
PC ← (PC) + 2; if R.1 = 1“1”
Description:
If bit 1 of R is equal to 1, the program counter is incremented by 2 and a
skip is produced. If bit 1 of R is not equal to 1, the program counter (PC) is
incremented.
SKB2
If bit 2 of R is equal to 1 then skip
R
Machine Code:
1
0
0
0
1
0
1
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
PC ← (PC) + 2; if R.2 = 1“1”
Description:
If bit 2 of R is equal to 1, the program counter is incremented by 2 and a
skip is produced. If bit 2 of R is not equal to 1. The program counter (PC) is
incremented.
SKB3
If bit 3 of R is equal to 1 then skip
R
Machine Code:
1
0
0
0
1
0
1
0
1
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
PC ← (PC) + 2; if R.3 = 1“1”
Description:
If bit 3 of R is equal to 1, the program counter is incremented by 2 and a
skip is produced. If bit 3 of R is not equal to 1, the program counter (PC) is
incremented.
- 89 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
STOP
Enter the STOP mode
Machine Code:
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
Machine Cycle:
1
Operation:
STOP oscillator
Description:
Device enters STOP mode. When the falling edge signal of RC port is
accepted, the µC will wake up and execute the next instruction.
SUB
Subtract ACC from R
R, ACC
Machine Code:
0
0
0
1
1
0
1
0
0
R6
R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) - (ACC)
Description:
The contents of the ACC are binary subtracted from the contents of the data
memory location addressed by R6 to R0 and the result is loaded into the
ACC.
Flag Affected:
CF & ZF
SUB
Subtract immediate data from WR
WR , #I
Machine Code:
0
0
0
1
1
1
1
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) - I
Description:
The immediate data I are binary subtracted from the contents of the WR
and the result is loaded into the ACC.
Flag Affected:
CF & ZF
- 90 -
W741E260
Instruction Set Table 2, continued
SUBR R, ACC
Subtract ACC from R
Machine Code:
0
0
0
1
1
0
1
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) - (ACC)
Description:
The contents of the ACC are binary subtracted from the contents of the data
memory location addressed by R6 to R0 and the result is placed in the ACC
and the data memory.
Flag Affected:
CF & ZF
SUBR
Subtract immediate data from WR
WR, #I
Machine Code:
0
0
0
1
1
1
1
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) - I
Description:
The immediate data I are binary subtracted from the contents of the WR
and the result is placed in the ACC and the WR.
Flag Affected:
CF & ZF
XRL
Exclusive OR R to ACC
R, ACC
Machine Code:
0
0
1
1
1
0
0
0
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC ← (R) EX (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are exclusive-ORed and the result is loaded into the ACC.
Flag Affected:
ZF
- 91 -
Publication Release Date: March 1998
Revision A2
W741E260
Instruction Set Table 2, continued
XRL
WR, #I
Exclusive OR immediate data to WR
Machine Code:
0
0
1
1
1
1
0
0
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC ← (WR) EX I
Description:
The contents of the Working Register (WR) and the immediate data I are
exclusive-ORed and the result is loaded into the ACC.
Flag Affected:
ZF
XRLR R, ACC
Exclusive OR R to ACC
Machine Code:
0
0
1
1
1
0
0
1
0
R6 R5 R4 R3 R2 R1 R0
Machine Cycle:
1
Operation:
ACC, R ← (R) EX (ACC)
Description:
The contents of the data memory location addressed by R6 to R0 and the
ACC are exclusive-ORed and the result is placed in the data memory and
the ACC.
Flag Affected:
ZF
XRLR
Exclusive OR immediate data to WR
WR, #I
Machine Code:
0
0
1
1
1
1
0
1
I3
I2
I1
I0
W3 W2 W1 W0
Machine Cycle:
1
Operation:
ACC, WR ← (WR) EX I
Description:
The contents of the Working Register(WR) and the immediate data I are
exclusive-ORed and the result is placed in the WR and the ACC.
Flag Affected:
ZF
- 92 -
W741E260
PACKAGE DIMENSIONS
80-Lead QFP
HD
D
80
65
64
1
E
E H
24
41
25
e
b
40
c
2
A A
Seating Plane
1
See Detail F
L
A
y
L1
Symbol
A
A1
A2
b
c
D
E
e
HD
HE
L
L1
y
0
Detail F
Dimension in mm
Dimension in inches
Min. Nom Max. Min. Nom Max.
0.130
3.30
0.004
0.10
0.107 0.112
0.117
2.73
2.85
2.97
0.012 0.014
0.018
0.30
0.35
0.45
0.004 0.006
0.010
0.10
0.15
0.25
0.546 0.551
0.556
13.87
14.00 14.13
20.00 20.13
0.782 0.787
0.792
19.87
0.025 0.031
0.037
0.65
0.80
0.728
0.740
0.752
18.49
18.80 19.10
0.964
0.976
0.988
24.49
24.80 25.10
0.039
0.047
0.055
1.00
1.20
1.40
0.087
0.094
0.103
2.21
2.40
2.62
0.004
0
12
0.95
0.10
0
- 93 -
12
Publication Release Date: March 1998
Revision A2
W741E260
NOTES:
Headquarters
Winbond Electronics (H.K.) Ltd.
Rm. 803, World Trade Square, Tower II,
No. 4, Creation Rd. III,
123 Hoi Bun Rd., Kwun Tong,
Science-Based Industrial Park,
Kowloon, Hong Kong
Hsinchu, Taiwan
TEL: 852-27513100
TEL: 886-3-5770066
FAX: 852-27552064
FAX: 886-3-5792766
http://www.winbond.com.tw/
Voice & Fax-on-demand: 886-2-27197006
Taipei Office
11F, No. 115, Sec. 3, Min-Sheng East Rd.,
Taipei, Taiwan
TEL: 886-2-27190505
FAX: 886-2-27197502
Note: All data and specifications are subject to change without notice.
- 94 -
Winbond Electronics North America Corp.
Winbond Memory Lab.
Winbond Microelectronics Corp.
Winbond Systems Lab.
2727 N. First Street, San Jose,
CA 95134, U.S.A.
TEL: 408-9436666
FAX: 408-5441798