ISO-CMOS MT093 8 x 12 Analog Switch Array Features ISSUE 2 March 1997 Ordering Information • • • • • • • • • Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5V to 14.5V 3.5Vpp analog signal capability RON 65Ω max. @ VDD=14V, 25°C ∆RON ≤ 10Ω @ VDD=14V, 25°C Full CMOS switch for low distortion Minimum feedthrough and crosstalk Low power consumption ISO-CMOS technology Applications • PBX systems • • • • Mobile radio Test equipment /instrumentation Analog/digital multiplexers Audio/Video switching STROBE 40 Pin Plastic DIP 44 Pin PLCC 0° to 70°C Description The Zarlink MT093 is fabricated in Zarlink’s ISOCMOS technology providing low power dissipation and high reliability. The device contains a 8x12 array of crosspoint switches along with a 7 to 96 line decoder and latch circuits. Any one of the 96 switches can be addressed by selecting the appropriate seven input bits. The selected switch can be turned on or off by applying a logical one or zero to the DATA input. DATA RESET 1 AX0 MT093AE MT093AP VDD VSS 1 8 x 12 Switch Array AX2 AX3 7 to 96 Decoder Latches AY0 AY1 AY2 96 •••••••••••••••• AX1 Xi I/O (i=0-11) 96 ••••••••••••••••••• Yi I/O (i=0-7) Figure 1 - Functional Block Diagram 3-65 Y3 AY2 RESET AX3 AX0 NC NC X6 X7 X8 X9 X10 X11 NC Y7 NC Y6 STROBE Y5 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 VDD Y2 DATA Y1 NC Y0 NC X0 X1 X2 X3 X4 X5 NC NC AY1 AY0 AX2 AX1 Y4 NC AX0 AX3 RESET AY2 Y3 VDD Y2 DATA Y1 Y0 ISO-CMOS NC NC X6 XY X8 X9 X10 X11 NC NC NC 6 5 4 3 2 1 44 43 42 41 40 7 39 8 38 9 37 10 36 11 35 12 34 13 33 14 32 15 31 16 30 29 17 18 19 20 21 22 23 24 25 26 27 28 NC NC X0 X1 X2 X3 X4 X5 NC NC NC Y7 Y6 STROBE Y5 VSS Y4 AX1 AX2 AY0 AY1 NC MT093 40 PIN PLASTIC DIP 44 PIN PLCC Figure 2 - Pin Connections Pin Description Pin # Name PDIP PLCC 1 2 3 4,5 6,7 8-13 1 2 3 4,5 6-8 9-14 14 15 16 17 18 15-17 18 19 20 19 20 21 22, 23 24, 25 26, 27 28 - 33 21 22 23 24,25 26,27 28-31 32-37 34 35 38,39 40 36 37 41 3-66 Y3 AY2 RESET AX3,AX0 NC X6-X11 Description Y3 Analog (Input/Output): this is connected to the Y3 column of the switch array. Y2 Address Line (Input). Master RESET (Input): this is used to turn off all switches. Active High. X3 and X0 Address Lines (Inputs). No Connection. X6-X11 Analog (Inputs/Outputs): these are connected to the X6-X11 rows of the switch array. NC No Connection. Y7 Y7 Analog (Input/Output): this is connected to the Y7 column of the switch array. NC No Connection. Y6 Y6 Analog (Input/Output): this is connected to the Y6 column of the switch array. STROBE STROBE (Input): enables function selected by address and data. Address must be stable before STROBE goes high and DATA must be stable on the falling edge of the STROBE. Active High. Y5 Y5 Analog (Input/Output): this is connected to the Y5 column of the switch array. VSS Ground Reference. Y4 Y4 Analog (Input/Output): this is connected to the Y4 column of the switch array. AX1,AX2 X1 and X2 Address Lines (Inputs). AY0,AY1 Y0 and Y1 Address Lines (Inputs). NC No Connection. X5-X0 X5-X0 Analog (Inputs/Outputs): these are connected to the X5-X0 rows of the switch array. NC No Connection. Y0 Y0 Analog (Input/Output): this is connected to the Y0 column of the switch array. NC No Connection. Y1 Y1 Analog (Input/Output): this is connected to the Y1 column of the switch array. ISO-CMOS MT093 Pin Description Pin # Name Description 42 DATA 39 43 Y2 40 44 VDD DATA (Input): a logic high input will turn on the selected switch and a logic low will turn off the selected switch. Active High. Y2 Analog (Input/Output): this is connected to the Y2 column of the switch array. Positive Power Supply. PDIP PLCC 38 Functional Description Address Decode The MT093 is an analog switch matrix with an array size of 8 x 12. The switch array is arranged such that there are 8 columns by 12 rows. The columns are referred to as the Y input/output lines and the rows are the X input/output lines. The crosspoint analog switch array will interconnect any X line with any Y line when turned on and provide a high degree of isolation when turned off. The control memory consists of a 96 bit write only RAM in which the bits are selected by the address input lines (AY0-AY2, AX0-AX3). Data is presented to the memory on the DATA input line. Data is asynchronously written into memory whenever the STROBE input is high and is latched on the falling edge of STROBE. A logical “1” written into a memory cell turns the corresponding crosspoint switch on and a logical “0” turns the crosspoint off. Only the crosspoint switches corresponding to the addressed memory location are altered when data is written into memory. The remaining switches retain their previous states. Any combination of X and Y lines can be interconnected by establishing appropriate patterns in the control memory. A logical “1” on the RESET input line will asynchronously return all memory locations to logical “0” turning off all crosspoint switches. The seven address lines along with the STROBE input are logically ANDed to form an enable signal for the resettable transparent latches. The DATA input is buffered and is used as the input to all latches. To write to a location, RESET must be low while the address and data lines are set up. Then the STROBE input is set high and then low causing the data to be latched. The data can be changed while STROBE is high, however, the corresponding switch will turn on and off in accordance with the data. Data must be stable on the falling edge of STROBE in order for correct data to be written to the latch. 3-67 MT093 ISO-CMOS Absolute Maximum Ratings*- Voltages are with respect to VSS unless otherwise stated. Parameter Symbol Min Max Units 1 Supply Voltage VDD VSS -0.3 -0.3 16.0 VDD+0.3 V V 2 Analog Input Voltage VINA -0.3 VDD+0.3 V 3 Digital Input Voltage VIN VSS-0.3 VDD+0.3 V 4 Current on any I/O Pin ±15 mA 5 Storage Temperature +150 °C 6 Package Power Dissipation 0.6 W I TS PLASTIC DIP -65 PD * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Recommended Operating Conditions - Voltages are with respect to VSS unless otherwise stated. Characteristics Sym Min Typ Max Units TO 0 25 70 °C 1 Operating Temperature 2 Supply Voltage VDD 4.5 14.5 V 3 Analog Input Voltage VINA VSS 3.5 V 4 Digital Input Voltage VIN VSS VDD V DC Electrical Characteristics†Characteristics 1 Voltages are with respect to VSS=0V, VDD =14V unless otherwise stated. Sym Quiescent Supply Current Test Conditions Min IDDQ Typ‡ Max Units Test Conditions 1 100 µA All digital inputs at VIN=VSS or VDD 7 15 mA All digital inputs at VIN=2.4V IVXi - VYjI = VDD - VSS 2 Off-state Leakage Current IOFF ±1 µA 3 Input Logic “0” level VIL 0.8 V 4 Input Logic “1” level VIH 5 Input Leakage (digital pins) 2.4 V µA 10 ILEAK All digital inputs at VIN = VSS or VDD † DC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. DC Electrical Characteristics- Switch Resistance - VIDC/VODC is the external DC offset applied at the analog I/O pins. Characteristics Sym 25°C Typ Max 1 On-state VDD=14V Resistance RON 45 65 2 Difference in on-state resistance between two switches ∆RON 5 10 3-68 60°C Typ Max 10 70°C Typ Units Test Conditions Max 75 Ω VSS=0V, IVXi-VYjI = 0.25V VIDC=6.75V VODC=6.5V 10 Ω VDD=14V, VSS=0, VIDC=6.75V VODC=6.5V IVXi-VYjI = 0.25V ISO-CMOS MT093 AC Electrical Characteristics† - Crosspoint Performance-VDC is the external DC offset applied at the analog I/O pins. Voltages are with respect to VDD=7V, VDC=0V, VSS=-7V, unless otherwise stated. Characteristics Sym Min Typ‡ Max Units Test Conditions 1 Switch I/O Capacitance CS 20 pF f=1 MHz 2 Feedthrough Capacitance CF 0.2 pF f=1 MHz 3 Frequency Response Channel “ON” 20LOG(VOUT/VXi)=-3dB F3dB 45 MHz Switch is “ON”; VINA = 2Vpp sinewave; RL = 1kΩ 4 Total Harmonic Distortion THD 0.05 % Switch is “ON”; VINA = 2Vpp sinewave f= 1kHz; RL=1kΩ 5 Feedthrough Channel “OFF” Feed.=20LOG (VOUT/VXi) FDT -95 dB All Switches “OFF”; VINA= 2Vpp sinewave f= 1kHz; RL= 1kΩ. 6 Crosstalk between any two channels for switches Xi-Yi and Xj-Yj. Xtalk -45 dB VINA=2Vpp sinewave f= 10MHz; RL = 75Ω. -90 dB VINA=2Vpp sinewave f= 10kHz; RL = 600Ω. -85 dB VINA=2Vpp sinewave f= 10kHz; RL = 1kΩ. -80 dB VINA=2Vpp sinewave f= 1kHz; RL = 10kΩ. ns RL=1kΩ; CL=50pF Xtalk=20LOG (VYj/VXi). 7 Propagation delay through switch tPS 50 † Timing is over recommended temperature range. ‡ Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. Crosstalk measurements are for Plastic DIPS only, crosstalk values for PLCC packages are approximately 5dB better. AC Electrical Characteristics† - Control and I/O Timings- VDC is the external DC offset applied at the analog I/O pins. Voltages are with respect to VDD=7V, VDC=0V, VSS=-7V, unless otherwise stated. Characteristics 1 Control Input crosstalk to switch (for DATA, STROBE, Address) 2 Sym Min Typ‡ Max Units Test Conditions CXtalk 50 mVpp Digital Input Capacitance CDI 10 pF 3 Switching Frequency FO 4 Setup Time DATA to STROBE tDS 20 ns RL= 1kΩ, CL=50pF 5 Hold Time DATA to STROBE tDH 20 ns RL= 1kΩ, CL=50pF 6 Setup Time Address to STROBE tAS 20 ns RL= 1kΩ, CL=50pF 7 Hold Time Address to STROBE tAH 20 ns RL= 1kΩ, CL=50pF 8 STROBE Pulse Width tSPW 40 ns RL= 1kΩ, CL=50pF 9 RESET Pulse Width tRPW 80 ns RL= 1kΩ, CL=50pF 10 STROBE to Switch Status Delay tS 80 200 ns RL= 1kΩ, CL=50pF 11 DATA to Switch Status Delay tD 100 200 ns RL= 1kΩ, CL=50pF 12 RESET to Switch Status Delay tR 70 200 ns RL= 1kΩ, CL=50pF 10 VIN=3V+VDC squarewave; RIN=1kΩ, RL=10kΩ. f=1MHz MHz † Timing is over recommended temperature range. Digital Input rise time (tr) and fall time (tf) = 10ns. ‡ Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. * 3-69 MT093 ISO-CMOS tRPW 50% RESET 50% tSPW STROBE 50% 50% 50% tAS ADDRESS 50% 50% tAH DATA 50% 50% tDS tDH ON SWITCH* OFF tR tS tD tR Figure 3 - Control Memory Timing Diagram AX0 AX1 AX2 AX3 AY0 AY1 AY2 Connection 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 X0-Y0 X1-Y0 X2-Y0 X3-Y0 X4-Y0 X5-Y0 ➀ No Connection ➀ No Connection X6-Y0 X7-Y0 X8-Y0 X9-Y0 X10-Y0 X11-Y0 ➀ No Connection ➀ No Connection 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 0 ↓ 0 ↓ X0-Y1 1 0 1 1 1 0 0 X11-Y1 0 ↓ 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 0 ↓ X0-Y2 1 0 1 1 0 1 0 X11-Y2 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 1 ↓ 0 ↓ X0-Y3 1 0 1 1 1 1 0 X11-Y3 0 ↓ 0 ↓ 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ X0-Y4 1 0 1 1 0 0 1 X11-Y4 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 0 ↓ 1 ↓ X0-Y5 1 0 1 1 1 0 1 X11-Y5 0 ↓ 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 1 ↓ X0-Y6 1 0 1 1 0 1 1 X11-Y6 0 ↓ 0 ↓ 0 ↓ 0 ↓ 1 ↓ 1 ↓ 1 ↓ X0-Y7 1 0 1 1 1 1 1 X11-Y7 Table 1. Address Decode Truth Table ➀ This address has no effect on device status. 3-70 ↓↓ ↓↓ ↓↓ ↓↓ ↓↓ ↓↓ ↓↓ For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE