AKM AKD4753-A

[AKD4753-A]
AKD4753-A
AK4753 Evaluation Board Rev.2
GENERAL DESCRIPTION
The AKD4753-A is an evaluation board for AK4753, 2-in, 4-out CODEC with DSP Functions. The
AKD4753-A has the Digital Audio I/F and can achieve the interface with digital audio systems via
optical connector.
■ Ordering guide
AKD4753-A
---
Evaluation Board for AK4753
(Control software and USB cable are packed with this.)
FUNCTION
• RCA connectors for analog audio input/output
• Optical connector for digital audio input
• On-board digital audio interface (AK4118A)
• Potentiometers for Volume and Bass gain control
• USB connector for serial control interface
•1k bits EEPROM
D3.3V
DVDD AVDD
Regulator
3.3V
+5V
GND
Regulator
USB 3.3V
EEPROM
USB
PIC4550
AINL
AINR
PORT4
LOUT1
AK4753
Opt In
AK4118A
(DIR)
ROUT1
ROUT2
PORT1
LOUT1
SAIN1
Volume
SAIN2
Bass Gain
Potentiometer
10 Pin Header
DSP
I2C
PORT3
PORT2
10 Pin Header
Figure 1. AKD4753-A Block Diagram
* Circuit diagram and PCB layout are attached at the end of this manual.
KM103902
2011/01
-1-
[AKD4753-A]
Evaluation Board Manual
■ Operation sequence
1)
Set up the power supply lines
Name of
jack
+5V
Color of
jack
Red
Used for
Open / Connect
Regulator T2:
AVDD, DVDD of AK4753,
Digital Logic
Should be always connected When default
setting.
AVDD
Red
AVDD of AK4753
DVDD
Red
DVDD of AK4753
D3.3V
Red
Digital Logic
AGND
Black
Analog Ground
Should be always connected when AVDD of
AK4753 is not supplied from regulator T2.
In this case “JP13” is set to “Open”.
Should be always connected when DVDD of
AK4753 is not supplied from regulator T2.
In this case “JP14” is set to “Open”.
Should be always connected when Digital
Logic is not supplied from regulator T2.
In this case “JP15” is set to “Open.”
Should be always connected.
DGND
Black
Digital Ground
Should be always connected.
Default
Setting
+5V
Open
Open
Open
GND
GND
Table 1. Set up the power supply lines
Each supply line should be distributed from the power supply unit.
2)
Setup the evaluation mode, jumper pins
(2-1) External Slave Mode
(a) Evaluation of using DIR of AK4118A <default>
(b) All interface signals including master clock are fed externally
(2-2) External Master Mode
(a) Evaluation of using DIR of AK4118A
(2-3) PLL Slave Mode
(a) Evaluation of using DIR AK4118A
(b) All interface signals including master clock are fed externally
(2-4) PLL Master Mode
(a) All interface signals including master clock are fed externally
3)
Power on
The AK4118A should be reset once bringing S1 (AK4118-PDN) “L” upon power-up.
The AK4753 should be reset once bringing S2 (AK4753-PDN) “L” upon power-up.
KM103902
2011/01
-2-
[AKD4753-A]
■ Evaluation mode
1)
External Slave Mode
(a) Evaluation of D/A using DIR of AK4118A. <default>
In case of AK4753 evaluation using AK4118A, it is necessary to correspond to audio interface format for
AK4753 and AK4118A.Please use AK4118A in the master mode.
PORT1(RX) is used. Nothing should be connected to PORT3(DSP) and J7(MCKI).
XTL
EXT
GND
JP4
AK4753-BICK
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
JP6
AK4753-LRCK
DIR
JP7
AK4753-MCLK
MCKI
DIR
EXT
JP3
EXT
Figure 2. Setting of D/A using DIR of AK4118A
(b) All interface signals including master clock are fed externally.
PORT3(DSP) is used. Nothing should be connected to PORT1(RX) and J7(MCKI).
JP4
AK4753-BICK
XTL
EXT
GND
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
SLAVE
DIR
JP7
AK4753-MCLK
EXT
JP18
MCLK_SEL
JP17
MODE_SEL
MASTER
JP6
AK4753-LRCK
MCKI
DIR
EXT
JP3
MUTEN
MCLK
Figure 3. Setting of all interface signals including master clock are fed externally
KM103902
2011/01
-3-
[AKD4753-A]
2)
External Master Mode
(a) Evaluation of D/A using DIR of AK4118A.
In case of AK4753 evaluation using AK4118A, it is necessary to correspond to audio interface format for
AK4753 and AK4118A.Please use AK4118A in the slave mode.
PORT1(RX) is used. Nothing should be connected to PORT3(DSP) and J7(MCKI).
XTL
EXT
GND
JP4
AK4753-BICK
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
JP6
AK4753-LRCK
DIR
JP7
AK4753-MCLK
MCKI
DIR
EXT
JP3
EXT
Figure 4. Setting of D/A using DIR of AK4118A
3)
PLL Slave Mode
(a) Evaluation of D/A using DIR of AK4118A.
In case of AK4753 evaluation using AK4118A, it is necessary to correspond to audio interface format for
AK4753 and AK4118A.Please use AK4118A in the master mode.
PORT1(RX) is used. Nothing should be connected to PORT3(DSP) and J7(MCKI).
XTL
EXT
GND
JP4
AK4753-BICK
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
JP6
AK4753-LRCK
DIR
JP7
AK4753-MCLK
MCKI
DIR
EXT
JP3
EXT
Figure 5. Setting of D/A using DIR of AK4118A
(b) All interface signals including master clock are fed externally.
PORT3(DSP) is used. Nothing should be connected to PORT1(RX) and J7(MCKI).
JP4
AK4753-BICK
XTL
EXT
GND
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
SLAVE
DIR
JP7
AK4753-MCLK
EXT
JP18
MCLK_SEL
JP17
MODE_SEL
MASTER
JP6
AK4753-LRCK
MCKI
DIR
EXT
JP3
MUTEN
MCLK
Figure 6. Setting of all interface signals including master clock are fed externally
KM103902
2011/01
-4-
[AKD4753-A]
4)
PLL Master Mode
(a) All interface signals including master clock are fed externally.
(a-1) Setup the MCKI.
X1(X’Tal) or J7(MCKI) are used. Nothing should be connected to PORT1(RX).
(a) When using X1(X’Tal)
JP7
AK4753-MCLK
JP3
JP7
AK4753-MCLK
XTL
EXT
GND
XTL
EXT
GND
MCKI
DIR
EXT
MCKI
DIR
EXT
JP3
(b) When using J7(MCKI)
Figure 7. Setup the MCKI
(a-2) Other Setting (BICK, LRCK and SDATA).
PORT3(DSP) is used. Nothing should be connected to PORT1(RX).
JP4
AK4753-BICK
DIR
EXT
JP5
AK4753-SDATA
DIR
EXT
JP17
MODE_SEL
MASTER
SLAVE
JP6
AK4753-LRCK
DIR
EXT
JP18
MCLK_SEL
MUTEN
MCLK
Figure 8. Other Setting (BICK, LRCK and SDATA)
KM103902
2011/01
-5-
[AKD4753-A]
■ EEP-ROM operation setting
JP8
JP10
JP9
WP
PC-SCL
PC-SDA
1) When you write the setting from Control Soft to EEPROM.
At this time, please fix the EXTEE switch (See Table 5) to "L".
Figure 9. Setting of EEP-ROM operation1
JP9
PC-SCL
JP8
WP
PC-SDA
JP10
2) When you load the setting from EEPROM to AK4753.
Please change the EXTEE switch (See Table 5) from "L" to "H" after setting JP8, JP9 and JP10.
Figure 10. Setting of EEP-ROM operation2
KM103902
2011/01
-6-
[AKD4753-A]
■ Jumper pins setting
[JP1 (SAIN1)]: The selection of connection to SAIN1 pin.
SHORT : Connection. (Default)
OPEN : Unconnection.
[JP2 (SAIN2)]: The selection of connection to SAIN2 pin.
SHORT : Connection. (Default)
OPEN : Unconnection.
[JP8 (PC-SCL)]: The selection of SCL signal.
SHORT : When you write the setting in EEPROM.
OPEN : When you load the setting from EEPROM. (Default)
[JP9 (WP)]: The selection of Write Protect setting of EEPROM.
SHORT : Write protect is Disable.
OPEN : Write protect is Enable. (Default)
[JP10 (PC-SDA)]: The selection of SDA signal.
SHORT : When you write the setting in EEPROM.
OPEN : When you load the setting from EEPROM. (Default)
[JP11]: Not to use.
[JP12 (GND)]: Analog ground and Digital ground.
SHORT : Common. (Default)
OPEN : Separated.
[JP16 (TEST)]: The selection of connection to TEST pin.
SHORT : Connect to VDD.
OPEN : Connect to GND. (Default)
■ Potentiometer setting
[R5]: Volume control
Upper - side: 0dB
Lower - side: Mute (-∞)
[R7]: Bass control
Upper - side: +12dB
Lower - side: -12dB
R5
SAIN1
R7
SAIN2
Figure 11. Potentiometers
KM103902
2011/01
-7-
[AKD4753-A]
■ DIR SW Setting
Upper-side is “ON(H)” and lower-side is “OFF(L)”.
[S3] (SW DIP-4): Mode setting for AK4118A.
No.
Name
ON (“H”)
1
2
3
4
OCKS0
OCKS1
DIF0
DIF1
OFF (“L”)
AK4118A Master Clock Setting
See Table 3
AK4118A Audio Interface Format Setting
See Table 4
Default
OFF
OFF
ON
OFF
Table 2. Mode Setting for AK4118A
OCKS1
OCKS0
MCKO1
L
H
H
L
L
H
256fs
512fs
Not to use
Default
Table 3. Setting for AK4118A Master Clock Setting
DIF2
Fixed
”H”
DIF1
L
L
H
H
DIF0
L
H
L
H
SDTO
24bit, Left justified
24bit, I2S
24bit, Left justified
24bit, I2S
LRCK
H/L O
L/H O
H/L
I
L/H
I
BICK
64fs
64fs
64-128fs
64-128fs
O
O
I
I
Default
Table 4. Setting for AK4118A Audio Interface Format Setting
[S4] (SW DIP-2): Mode setting for AK4753.
No.
Name
ON (“H”)
OFF (“L”)
Default
1
2
EXTEE
BYPASS
EEP-ROM Download Mode
DSP Bypass Mode
Serial Control Mode
Normal Operation
OFF
OFF
Table 5. Mode Setting for AK4753
KM103902
2011/01
-8-
[AKD4753-A]
■ Function of the Toggle SW
Upper-side is “H” and lower-side is “L”.
[S1] (AK4118-PDN): Resets the AK4118A. Keep “H” during normal operation.
The AK4118A should be resets once bringing “L” upon power-up.
[S2] (AK4753-PDN): Resets the AK4753. Keep “H” during normal operation.
The AK4753 should be resets once bringing “L” upon power-up.
■ Indication for LED
[LED1] (STO): Monitor STO pin of the AK4753.
LED turns on when Read error of EEPROM has occurred to AK4753.
[LED2] (EFR): Monitor INT0 pin of the AK4118A.
LED turns on when some error has occurred to AK4118A.
■ Control Port
It is possible to control AKD4753-A via general USB port. Connect cable with the USB port on board and PC.
Control software is packed with this board. The software operation sequence is included in the evaluation board
manual.
KM103902
2011/01
-9-
[AKD4753-A]
■ Analog Input / Output Circuits
1) Analog Inputs
(a) AINL, AINR
J1
AINR
C2
+
2
3
4
5
1
AINR
1u
R1
(open)
J3
AINL
C4
+
2
3
4
5
1
AINL
1u
R3
(open)
Figure 12. Circuit diagram of AINL and AINR
(b) SAIN1, SAIN2
SAIN1
R5
AVDD
10k
C9
(OPEN)
SAIN2
R7
10k
C12
(OPEN)
Figure 13. Circuit diagram of SAIN1 and SAIN2
KM103902
2011/01
- 10 -
[AKD4753-A]
2) Analog Outputs
(a) STEREO Mode (Full-differential)
LOUT+
TEST1
LOUT+
C1
+
J2
LOUT1
ROUT-
10u
C3
(OPEN)
LOUT-
J5
ROUT2
10u
R2
C8
(OPEN)
(open)
TEST2
LOUT-
C5
+
J4
ROUT1
ROUT+
10u
C6
(OPEN)
TEST3
ROUT-
C7
+
R6
(open)
TEST4
ROUT+
C10
+
J6
LOUT2
10u
R4
C11
(OPEN)
(open)
R8
(open)
Figure 14. Circuit diagram of STEREO Mode
(b) 2.1-channel Mode
LOUT1
TEST1
LOUT+
C1
+
J2
LOUT1
SW-
10u
C3
(OPEN)
ROUT1
10u
C8
(OPEN)
R2
(open)
TEST2
LOUT-
C5
+
J4
ROUT1
SW+
10u
C6
(OPEN)
(open)
J5
ROUT2
R6
(open)
TEST4
ROUT+
C10
+
10u
C11
(OPEN)
R4
TEST3
ROUT-
C7
+
J6
LOUT2
R8
(open)
Figure 15. Circuit diagram of 2.1-channel Mode
(c) 4-channel Mode (Single-ended)
LOUT1
TEST1
LOUT+
C1
+
J2
LOUT1
ROUT2
10u
C3
(OPEN)
ROUT1
J5
ROUT2
10u
R2
C8
(OPEN)
(open)
TEST2
LOUT-
C5
+
J4
ROUT1
LOUT2
10u
C6
(OPEN)
TEST3
ROUT-
C7
+
R6
(open)
TEST4
ROUT+
C10
+
J6
LOUT2
10u
R4
C11
(OPEN)
(open)
R8
(open)
Figure 16. Circuit diagram of 4-channel Mode
KM103902
2011/01
- 11 -
[AKD4753-A]
Control Soft Manual
■ Evaluation Board and Control Soft Settings
1. Set an evaluation board properly.
2. Connect Evaluation board to PC with USB cable.
USB control is recognized as HID (Human Interface Device) on the PC.
When it can not be recognized correctly please Connect Evaluation board to PC with USB cable.
3. Proceed evaluation by following the process below.
■Operation Screen
1. Start up the control program following the process above.
2. After the evaluation board’s power is supplied, the AK4753 must be reset once bring S2 (AK4753-PDN) “L” to
“H”.
3. The operation screen is shown below.
Figure 17. Window of Control Soft
KM103902
2011/01
- 12 -
[AKD4753-A]
■Operation Overview
Function, register map and testing tool can be controlled by this control soft. These controls are selected by upper tabs.
Buttons which are frequently used such as register initializing button “Write Default”, are located outside of the
switching tab window. Refer to the “■Dialog Boxes” for details of each dialog box setting.
1.
[Port Reset]: For when connecting to USB I/F board (AKDUSBIF-B)
Click this button after the control soft starts up when connecting USB I/F board (AKDUSBIF-B).
2.
[Write Default]: Register Initializing
When the device is reset by a hardware reset, use this button to initialize the registers.
3.
[All Write]: Executing write commands for all registers displayed.
4.
[All Read]: Executing read commands for all registers displayed.
5.
[Save]: Saving current register settings to a file.
6.
[Load]: Executing data write from a saved file.
7.
[All Reg Write]: “All Reg Write” dialog box is popped up.
8.
[Data R/W]: “Data R/W” dialog box is popped up.
9.
[Sequence]: “Sequence” dialog box is popped up.
10. [Sequence(File)]: “Sequence(File)” dialog box is popped up.
11. [EEPROM Write]: Executing EEPROM write.
12. [Read]: Reading current register settings and display on to the Register area on the right of the main window.
This is different from [All Read] button, it does not reflect to a register map, only displaying
hexadecimal.
KM103902
2011/01
- 13 -
[AKD4753-A]
■ Tab Functions
1. [Function]: Function control
This tab is for function control.
Each operation is executed by the function buttons on the left side of the screen.
Figure 18.Window of [Function]
KM103902
2011/01
- 14 -
[AKD4753-A]
1-1. [Mode Setting]: Power Management and Signal Path Setting
When [Mode Setting] button is clicked, the window as shown in opens.
This window is for Power Management and Signal Path Setting.
Refer to the datasheet for register settings of the AK4753.
Figure 19. Window of [Mode Setting]
1-2. [PLL Setting]: System Clock and Audio I/F Setting
When [PLL Setting] button is clicked, the window as shown in opens.
This window is for System Clock and Audio I/F Setting.
Refer to the datasheet for register settings of the AK4753.
Figure 20. Window of [PLL Setting]
KM103902
2011/01
- 15 -
[AKD4753-A]
1-3. [Volume Setting]: Volume Setting
When [Volume Setting] button is clicked, the window as shown in opens.
This window is for Volume Setting.
Refer to the datasheet for register settings of the AK4753.
Figure 21. Window of [Volume Setting]
1-3-1. Register map
The volume can be controlled by slide bars.
A register writing is made on every slide bar move.
After the volume slide is moved, it is reflected on to the register map and data writing dialog box.
1-3-2. Volume Control by Slide bar
Slide bar is moved to the selected value
Figure 22. Volume Control by Slide bar
The volume can also be changed by writing a value in a dialog box. The slide bar is moved to the value that
written in the dialog box. Use the mouse or arrow keys on the keyboard for small adjustments.
KM103902
2011/01
- 16 -
[AKD4753-A]
1-4. [Digital Filter Setting]: Filter Setting
A calculation of a coefficient of Digital Programmable Filters such as HPF / LPF and EQ filters,
a register writing and a frequency response checking of HPF / LPF and EQ filters can be made.
When [Digital Filter Setting] button is clicked, the window as shown in opens.
Refer to the datasheet for register settings of the AK4753.
Figure 23. Window of [Digital Filter Setting]
KM103902
2011/01
- 17 -
[AKD4753-A]
1-4-1. Parameter Setting
(1)
Please set a parameter of each Filter.
Parameter
Function
Sampling Rate
HPF
Cut Off Frequency
Setting Range
Sampling frequency (fs)
7350Hz ≤ fs ≤ 48000Hz
High pass filter cut off frequency
1.042x10-3 ≤ fc/fs ≤ 0.24
LPF
Cut Off Frequency
Low pass filter cut off frequency
5.208x10-3 ≤ fc/fs ≤ 0.24
5 Band Equalizer
EQ1-5 Center Frequency
EQ1-5 Band Width
EQ1-5 Gain
EQ1-5 Center Frequency
EQ1-5 Band Width
EQ1-5 Gain
(Note 1)
(Note 2)
3.125x10-3 ≤ fon/fs < 0.4969
fbn/fs ≤ 0.25
-1≤ Gain < 3
Table 6. Parameter Setting
Note 1. A gain difference is a bandwidth of 3dB from center frequency.
Note 2. When a gain is smaller than 0 , EQ becomes a notch filter.
(2) “HPF LPF Enable” , “HPF” ,”LPF” , “EQ1”, “EQ2”, “EQ3”, “EQ4”, “EQ5”
Please set ON/OFF of Filter with a check button. When checked it, Filter becomes ON.
When “Notch Filter Auto Correction” is checked, perform automatic correction of the center frequency
of the notch filter is executed.
Figure 24. Filter ON/OFF setting button
KM103902
2011/01
- 18 -
[AKD4753-A]
1-4-2. A calculation of a register
A register set value is displayed when push a [Register Setting] button. When a value out of a setting range is
set, error message is displayed, and a calculation of register setting is not carried out.
Figure 25. A register setting calculation result
Followings are the cases when a register set value is updated.
(1) When [Register Setting] button was pushed.
(2) When [F Response] button was pushed.
(3) When [UpDate] button was pushed on a frequency characteristic indication window.
(4) When set ON/OFF of a check button “HPF LPF Enable”, “HPF” ,”LPF”,“EQ1”, “EQ2”, “EQ3”,
“EQ4”, “EQ5”
KM103902
2011/01
- 19 -
[AKD4753-A]
1-4-3. Indication of a frequency characteristic
A frequency characteristic is displayed when push a [F Response] button. Then, a register set point is also
updated.
Change "Frequency Range", and indication of a frequency characteristic is updated when push a [UpDate]
button.
Figure 26. A frequency characteristic indication result
Followings are the cases when a register set value is updated.
(1) When [Register Setting] button was pushed.
(2) When [F Response] button was pushed.
(3) When [UpDate] button was pushed on a frequency characteristic indication window.
(4) When set ON/OFF of a check button “HPF LPF Enable”, “HPF” ,”LPF”,“EQ1”, “EQ2”, “EQ3”,
“EQ4”, “EQ5”
KM103902
2011/01
- 20 -
[AKD4753-A]
1-4-4. Filter Setting
The filter setting can be executed by dragging the number to 1-5 in the mouse.
Band Width can be adjusted in the operation of Center Frequency and Gain right-clicking in the operation of
the left-click.
After it moves, a set
value is reflected.
It moves by the left-click.
Figure 27. Filter Setting(Left-clicking operation)
Band Width is revokable when
sideways moving to right-click.
Figure 28. Filter Setting(Right-clicking operation)
KM103902
2011/01
- 21 -
[AKD4753-A]
1-5. [Limiter Setting]: Limiter Setting
When [Limiter Setting] button is clicked, the window as shown in opens.
This window is for Limiter Setting.
Refer to the datasheet for register settings of the AK4753.
Figure 29. Window of [Limiter Setting]
KM103902
2011/01
- 22 -
[AKD4753-A]
2. [REG]: Register Map
This tab is for a register writing and reading.
Each bit on the register map is a push-button switch.
Button Down indicates “H” or “1” and the bit name is in red (when read only it is in deep red).
Button Up indicates “L” or “0” and the bit name is in blue (when read only it is in gray)
Grayout registers are Read Only registers. They can not be controlled.
The registers which is not defined in the datasheet are indicated as “---”.
Figure 30. Window of [REG]
KM103902
2011/01
- 23 -
[AKD4753-A]
2-1. [Write]: Data Writing Dialog
It is for when changing two or more bits on the same address at the same time.
Click [Write] button located on the right of the each corresponded address for a pop-up dialog box.
When checking the checkbox, the register will be “H” or “1”, when not checking the register will be “L”
or ”0”.
Click [OK] to write setting value to the registers, or click [Cancel] to cancel this setting.
Figure 31. Window of [Register Set]
2-2. [Read]: Data Read
Click [Read] button located on the right of the each corresponded address to execute register reading.
After register reading, the display will be updated regarding to the register status.
Button Down indicates “H” or “1” and the bit name is in red (when read only it is in deep red).
Button Up indicates “L” or “0” and the bit name is in blue (when read only it is in gray)
Please be aware that button statuses will be changed by Read command.
KM103902
2011/01
- 24 -
[AKD4753-A]
3. [Tool]: Testing Tools
This tab screen is for evaluation testing tool.
Click buttons for each testing tool.
Figure 32. Window of [Tool]
KM103902
2011/01
- 25 -
[AKD4753-A]
3-1. [Repeat Test]: Repeat Test Dialog
Click [Repeat Test] button to open repeat test setting dialog box.
Figure 33. Window of [Repeat Test]
3-2. [Loop Setting]: Loop Setting Dialog
Click [Loop Setting] button to open loop setting dialog box.
Figure 34. Window of [Loop]
KM103902
2011/01
- 26 -
[AKD4753-A]
■Dialog Boxes
1. [All Reg Write]: ALL Register Write
Click [All Reg Write] button in the main window to open register setting files.
Register setting files saved by [SAVE] button can be applied.
Figure 35. Window of [All Reg Write]
[Open (left)]
[Write]
[Write All]
[Help]
[Save]
[Open (right)]
[Close]
: Selecting a register setting file (*.akr).
: Executing register writing.
: Executing all register writings.
Writings are executed in descending order.
: Help window is popped up.
: Saving the register setting file assignment. The file name is “*.mar”.
: Opening a saved register setting file assignment “*. mar”.
: Closing the dialog box and finish the process.
*Operating Suggestions
(1) Those files saved by [Save] button and opened by [Open] button on the right of the dialog “*.mar”
should be stored in the same folder.
(2) When register settings are changed by [Save] button in the main window, re-read the file to reflect
new register settings.
KM103902
2011/01
- 27 -
[AKD4753-A]
2. [Data R/W]: Data Read/Write
Click the [Data R/W] button in the main window for data read/write dialog box.
Data write is available to specified address.
Figure 36. Window of [Data R/W]
Address Box
Data Box
Mask Box
[Write]
[Close]
: Input data address in hexadecimal numbers for data writing.
: Input data in hexadecimal numbers.
: Input mask data in hexadecimal numbers.
This is “AND” processed input data.
: Writing to the address specified by “Address” box.
: Closing the dialog box and finish the process.
Data writing can be cancelled by this button instead of [Write] button.
*The register map will be updated after executing [Write] or [Read] commands.
KM103902
2011/01
- 28 -
[AKD4753-A]
3. [Sequence]: Sequence
Click [Sequence] button to open register sequence setting dialog box.
Register sequence can be set in this dialog box.
Figure 37. Window of [Sequence]
3-1. Sequence Setting
Set register sequence by following process bellow.
(1)Select a command
Use [Select] pull-down box to choose commands.
Corresponding boxes will be valid.
< Select Pull-down menu >
· No_use
· Register
· Reg(Mask)
· Interval
· Stop
· End
: Not using this address
: Register writing
: Register writing (Masked)
: Taking an interval
: Pausing the sequence
: Finishing the sequence
KM103902
2011/01
- 29 -
[AKD4753-A]
(2)Input sequence
[Address] : Data address
[Data]
: Writing data
[Mask]
: Mask
[Data] box data is ANDed with [Mask] box data. This is the actual writing data.
When Mask = 0x00, current setting is hold.
When Mask = 0xFF, the 8bit data which is set in the [Data] box is written.
When Mask =0x0F, lower 4bit data which is set in the [Data] box is written.
Upper 4bit is hold to current setting.
[Interval] : Interval time
Valid boxes for each process command are shown bellow.
· No use
· Register
· Reg(Mask)
· Interval
· Stop
· End
: None
: [Address], [Data], [Interval]
: [Address], [Data], [Mask], [Interval]
: [Interval]
: None
: None
3-2. Control Buttons
The function of Control Button is shown bellow.
[Start]
[Help]
[Save]
[Open]
[Close]
: Executing the sequence
: Opening a help window
: Saving sequence settings as a file. The file name is “*.aks”.
: Opening a sequence setting file “*.aks”.
: Closing the dialog box and finish the process.
3-3. Stop of the sequence
When “Stop” is selected in the sequence, processing is paused and it starts again when [Start] button is
clicked. Restarting step number is shown in the “Start Step” box. When finishing the process until the end of
sequence, “Start Step” will return to “1”.
The sequence can be started from any step by writing the step number to the “Start Step” box.
Write “1” to the “Start Step” box and click [Start] button, when restarting the process from the beginning.
KM103902
2011/01
- 30 -
[AKD4753-A]
4. [Sequence(File)] : Sequence(File)
Click [Sequence(File)] button to open sequence setting file dialog box.
Those files saved in the “Sequence setting dialog” can be applied in this dialog.
Figure 38. Window of [Sequence(File)]
[Open (left)]
[Start]
[Start All]
[Help]
[Save]
[Open(right)]
[Close]
: Opening a sequence setting file (*.aks).
: Executing the sequence setting.
: Executing all sequence settings.
Sequences are executed in descending order.
: Pop up the help window.
: Saving sequence setting file assignment. The file name is “*.mas”.
: Opening a saved sequence setting file assignment “*. mas”.
: Closing the dialog box and finish the process.
*Operating Suggestions
(1) Those files saved by [Save] button and opened by [Open] button on the right of the dialog
“*.mas” should be stored in the same folder.
(2) When “Stop” is selected in the sequence the process will be paused and a pop-up message will appear.
Click “OK” to continue the process.
Figure 39. Window of [Sequence Pause]
KM103902
2011/01
- 31 -
[AKD4753-A]
5. [EEPROM] : Write
Press the [EEPROM Write] button. Register setting wrings to EEPROM.
The following messages are displayed according to the result of processing.
・Writing failure
Figure 40. Window of [Writing failure]
・Writing success
Figure 41. Window of [Writing success]
KM103902
2011/01
- 32 -
[AKD4753-A]
Measurement Result
[Measurement condition]
• Measurement Unit
• MCLK
• BICK
• fs
• Power Supply
• Band Width
• Measurement Mode
• Temperature
: Audio Precession System Two Cascade
: 11.2896MHz (DAC)
12.288MHz (ADC to DAC)
: 64fs
: 44.1kHz
: AVDD=DVDD=3.3V
: 22Hz ~ 22kHz
: External Slave Mode (DAC)
External Slave Mode (ADC to DAC)
: Room Temperature
[Measurement Result]
1. DAC
a). Single-ended, LOUT1/ROUT1, LOUT2/ROUT2 RL=Open
Parameter
S/(N+D)
(0dBFS Input)
D-Range
(-60dB Input, A-weighted)
S/N
(No Signal, A-weighted)
Output Voltage
Lch1
Result
/
Rch1
Lch2
Result
/
Rch2
Unit
88.7
/
88.1
88.3
/
88.1
dB
99.2
/
98.7
99.2
/
98.3
dB
99.2
/
98.7
99.2
/
98.5
dB
2.40
/
2.40
2.40
/
2.40
Vpp
Lch
Result
/
b). Differential, LOUT/ROUT, RL=Open
Parameter
Rch
Unit
S/(N+D)
(0dBFS Input)
D-Range
(-60dB Input, A-weighted)
S/N
(No Signal, A-weighted)
87.5
/
87.8
dB
102.8
/
103.3
dB
103.1
/
103.3
dB
Output Voltage
±2.40
/
±2.40
Vpp
KM103902
2011/01
- 33 -
[AKD4753-A]
2. ADC to DAC
a). Single-ended, LOUT1/ROUT1, LOUT2/ROUT2 RL=Open
Parameter
S/(N+D)
(-1dBFS Input)
D-Range
(-60dB Input, A-weighted)
S/N
(No Signal, A-weighted)
Lch1
Result
/
Rch1
Lch2
Result
/
Rch2
Unit
86.4
/
86.3
86.5
/
86.3
dB
95.1
/
95.0
95.1
/
95.0
dB
95.1
/
95.0
95.1
/
95.0
dB
Lch
Result
/
b). Differential, LOUT/ROUT, RL= Open
Parameter
S/(N+D)
(-1dBFS Input)
D-Range
(-60dB Input, A-weighted)
S/N
(No Signal, A-weighted)
KM103902
Rch
Unit
85.8
/
85.7
dB
96.5
/
96.5
dB
96.5
/
96.5
dB
2011/01
- 34 -
[AKD4753-A]
PLOT DATA
1-a). DAC Single-ended [LOUT1/ROUT1 pins]
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz 0dBFS Input, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
10k
20k
Hz
Figure 42. FFT(0dBFS Input)
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, -60dBFS Input, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
Hz
Figure 43. FFT(-60dB Input)
KM103902
2011/01
- 35 -
[AKD4753-A]
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, No Signal, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 44. FFT(No Signal)
AK4753 THD+N vs. Input Level [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, External Slave Mode
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
-140
-120
-100
-80
-60
-40
-20
+0
dBFS
Figure 45. THD+N vs. Input Level
KM103902
2011/01
- 36 -
[AKD4753-A]
AK4753 THD+N vs. Input Frequency [LOUT1/ROUT1]
fs=44.1kHz, 0dBFS Input, External Slave Mode
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 46. THD+N vs. Input Frequency
AK4753 Linearity [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, EXT Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 47. Linearity
KM103902
2011/01
- 37 -
[AKD4753-A]
AK4753 Frequency Response [LOUT1/ROUT1]
fs=44.1kHz, 0dBFS Input, External Slave Mode
+1
+0.8
+0.6
+0.4
+0.2
d
B
r
+0
A
-0.2
-0.4
-0.6
-0.8
-1
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 48. Frequency Response
AK4753 Crosstalk [LOUT1/ROUT1]
fs=44.1kHz, 0dBFS Input, External Slave Mode
+0
T TT
T T
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 49. Crosstalk
KM103902
2011/01
- 38 -
[AKD4753-A]
PLOT DATA
1-b). DAC Differential [LOUT/ROUT pins]
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, 0dBFS Input, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
10k
20k
Hz
Figure 50. FFT(0dBFS Input)
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, -60dBFS Input, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
Hz
Figure 51. FFT(-60dB Input)
KM103902
2011/01
- 39 -
[AKD4753-A]
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, No Signal, External Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 52. FFT(No Signal)
AK4753 THD+N vs. Input Level [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, External Slave Mode
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
-140
-120
-100
-80
-60
-40
-20
+0
dBFS
Figure 53. THD+N vs. Input Level
KM103902
2011/01
- 40 -
[AKD4753-A]
AK4753 THD+N vs. Input Frequency [LOUT+-/ROUT+-]
fs=44.1kHz, 0dBFS Input, External Slave Mode
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 54. THD+N vs. Input Frequency
AK4753 Linearity [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, EXT Slave Mode
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 55. Linearity
KM103902
2011/01
- 41 -
[AKD4753-A]
AK4753 Frequency Response [LOUT+-/ROUT+-]
fs=44.1kHz, 0dBFS Input, External Slave Mode
+1
+0.8
+0.6
+0.4
+0.2
d
B
r
+0
A
-0.2
-0.4
-0.6
-0.8
-1
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 56. Frequency Response
AK4753 Crosstalk [LOUT+-/ROUT+-]
fs=44.1kHz, 0dBFS Input, External Slave Mode
+0
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 57. Crosstalk
KM103902
2011/01
- 42 -
[AKD4753-A]
PLOT DATA
2-a). ADC to DAC Single-ended [LOUT1/ROUT1 pins]
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, -1dBFS Input
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 58. FFT(-1dBFS Input)
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, -60dBFS Input
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 59. FFT(-60dBFS Input)
KM103902
2011/01
- 43 -
[AKD4753-A]
AK4753 FFT [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz, No Signal
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 60. FFT(No Signal)
AK4753 THD+N vs. Input Level [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
-140
-120
-100
-80
-60
-40
-20
dBr
Figure 61. THD+N vs. Input Level
KM103902
2011/01
- 44 -
[AKD4753-A]
AK4753 THD+N vs. Input Frequency [LOUT1/ROUT1]
fs=44.1kHz, -1dBFS Input
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 62. THD+N vs. Input Frequency
AK4753 Linearity [LOUT1/ROUT1]
fs=44.1kHz, fin=1kHz
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBr
Figure 63. Linearity
KM103902
2011/01
- 45 -
[AKD4753-A]
AK4753 FrequencyResponse [LOUT1/ROUT1]
fs=44.1kHz, -1dBFS Input
+0
-0.2
-0.4
-0.6
-0.8
-1
-1.2
d
B
r
-1.4
-1.6
A
-1.8
-2
-2.2
-2.4
-2.6
-2.8
-3
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 64. Frequency Response
AK4753 Crosstalk [LOUT1/ROUT1]
fs=44.1kHz, -1dBFS Input
+0
TT TTT T
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 65. Crosstalk
KM103902
2011/01
- 46 -
[AKD4753-A]
PLOT DATA
2-b). ADC to DAC Differential [LOUT/ROUT pins]
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, -1dBFS Input
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 66. FFT(-1dBFS Input)
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, -60dBFS Input
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 67. FFT(-60dBFS Input)
KM103902
2011/01
- 47 -
[AKD4753-A]
AK4753 FFT [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz, No Signal
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 68. FFT(No Signal)
AK4753 THD+N vs. Input Level [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
-140
-120
-100
-80
-60
-40
-20
dBr
Figure 69. THD+N vs. Input Level
KM103902
2011/01
- 48 -
[AKD4753-A]
AK4753 THD+N vs. Input Frequency [LOUT+-/ROUT+-]
fs=44.1kHz, -1dBFS Input
-50
-55
-60
-65
-70
-75
d
B
r
-80
A
-90
-85
-95
-100
-105
-110
-115
-120
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 70. THD+N vs. Input Frequency
AK4753 Linearity [LOUT+-/ROUT+-]
fs=44.1kHz, fin=1kHz
+0
-10
-20
-30
-40
-50
d
B
r
-60
A
-80
-70
-90
-100
-110
-120
-130
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBr
Figure 71. Linearity
KM103902
2011/01
- 49 -
[AKD4753-A]
AK4753 FrequencyResponse [LOUT+-/ROUT+-]
fs=44.1kHz, -1dBFS Input
+0
-0.2
-0.4
-0.6
-0.8
-1
-1.2
d
B
r
-1.4
-1.6
A
-1.8
-2
-2.2
-2.4
-2.6
-2.8
-3
20
50
100
200
500
1k
2k
5k
10k
20k
5k
10k
20k
Hz
Figure 72. Frequency Response
AK4753 Crosstalk [LOUT+-/ROUT+-]
fs=44.1kHz, -1dBFS Input
+0
T TT
T TT
T
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
20
50
100
200
500
1k
2k
Hz
Figure 73. Crosstalk
KM103902
2011/01
- 50 -
[AKD4753-A]
Revision History
Date
(YY/MM/DD)
10/09/17
10/09/30
Manual
Revision
KM103900
KM103901
Board
Revision
0
1
Reason
Contents
First Edition
Description Change Measurement results ware changed.
Board Modification Schematic circuit diagram was changed.
11/01/28
KM103902
2
Description Change Control soft manual was changed.
Measurement results ware changed.
Board Modification AK4753: Rev.A → Rev.B
IMPORTANT NOTICE
! These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
! Descriptions of external circuits, application circuits, software and other related information contained in this
document are provided only to illustrate the operation and application examples of the semiconductor products.
You are fully responsible for the incorporation of these external circuits, application circuits, software and other
related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by
you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of
any patent, intellectual property, or other rights in the application or use of such information contained herein.
! Any export of these products, or devices or systems containing them, may require an export license or other
official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency
exchange, or strategic materials.
! AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support,
or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system
containing it, and which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to
function or perform may reasonably be expected to result in loss of life or in significant injury or damage to
person or property.
! It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise
places the product with a third party, to notify such third party in advance of the above content and conditions, and
the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from
any and all claims arising from the use of said product in the absence of such notification.
KM103902
2011/01
- 51 -
5
4
3
2
J1
+
C2
1
J2
LOUT1
1
LOUT1
+
2
3
4
5
D
LOUT+
TEST1
C1
AINR
1
2
3
4
5
AINR
10u
R1
1u
C3
(OPEN)
(open)
R2
(open)
D
VSS1
VSS1
LOUTTEST2
J3
AINL
C4
C5
+
+
2
3
4
5
1
AINL
R3
1
ROUT1
1u
10u
C6
(OPEN)
(open)
J4
ROUT1
2
3
4
5
R4
(open)
C
C
VSS1
ROUTTEST3
VSS1
+
C7
J5
ROUT2
1
ROUT2
2
3
4
5
SAIN1
10u
R5
C8
(OPEN)
AVDD
10k
R6
(open)
VSS1
C9
(OPEN)
VSS1
B
B
+
SAIN2
10u
10k
C11
(OPEN)
VSS1
J6
LOUT2
1
LOUT2
R7
C12
ROUT+
TEST4
C10
R8
2
3
4
5
(open)
(OPEN)
VSS1
A
A
Title
AKD4753-A
- 52 5
4
3
Size
A
Date:
Document Number
Rev
1
AIN / AOUT
Wednesday, September 29, 2010
2
Sheet
of
1
1
5
3
2
SAIN1
VSS2
1
SAIN2
4
AK4753-PDN
5
VSS1
VSS1
CN1
TEST5
PDN
12
SAIN2
TEST8
VSS1
13
D
VSS1
VSS2
JP16
TEST
R52
5
4
3
2
1
CD
NC
VSS
VDD
OUT
TEST7
AVDD
DVDD
14
15
17
18
19
16
TEST6
SAIN1
U2
S-80923CNMC
20
D
21
22
44pin_2
R10
C72
(open)
EXTEE
C16
(OPEN)
11
9
10
TEST12
AINR
SAIN2
SAIN1
TEST
11
12
FLT
14
PDN
51
EXTEE
R12
13
16
EESDA
24
15
EESDA
TEST11
EESDA
(OPEN)
CN3
23
VSS2
C14
R11
10k
VSS2
CN2
JP2
SAIN2
TEST10
TEST
C71
(open)
TEST9
FLT
C15
4.7n
JP1
SAIN1
10k
C13
4.7n
100k
TEST15
EESCL
51
17
EESCL
AINL
8
TEST14
SDA
18
SDA
VSS1
7
8
C17
0.1u
R15
27
51
19
SCL
MUTEN
20
28
29
R16
STO
LOUT1
5
ROUT1
4
ROUT2
3
0
30
R18
51
22
R20
51
23
LRCK
LOUT2
2
R22
51
24
BICK
VCOM
1
SDTI
TEST25
0
31
32
TEST27
TEST28
ROUT1
4
ROUT2
3
LOUT2
BYPASS
TEST26
0
LOUT2
C22
(OPEN)
C23
C24
0.1u
2.2u
TEST29
VSS1
2
TEST30
VSS1
DVDD
DVDD
32
NC
1
31
REG
VSS2
30
XTO
DVDD
29
28
44pin_3
27
NC
B
26
25
VSS2
5
ROUT2
VCOM
XTI/MCKI
BICK
33
LOUT1
TEST24
C21
(OPEN)
R21
LRCK
AK4753-BICK
6
ROUT1
C20
(OPEN)
R19
SDTI
AK4753-LRCK
AVDD
TEST22
C19
(OPEN)
R17
TEST23
AK4753-SDTI
7
LOUT1
0
AK4753
STO
6
VSS1
AVDD
10u
TEST20
MUTEN
TEST21
21
AVDD
U1
TEST19
TEST18
C18
+
51
SCL
STO
C
VSS1
R13
TEST17
MUTEN
AINL
TEST16
26
SCL
AINR
9
AINL
R14
25
SDA
10
TEST13
EESCL
C
VSS1
AINR
B
44pin_1
XTL
EXT
GND
C25
0.1u
JP3
DVDD
2.2u
+
C27
X1
1
C26
2
TEST31
10u
12.288MHz
C28
C29
10p
10p
REG
DVDD
VSS2
TEST37
44
EXTEE
TEST36
43
42
41
40
VSS2
TEST34
39
38
MCLK
TEST33
37
36
35
VSS2
TEST32
34
BYPASS
TEST35
EXTEE
R23
0
CN4
44pin_4
A
A
EXTEE
VSS2
BYPASS
AK4753-MCLK
VSS2
VSS2
Title
AKD4753-A
- 53 -
Size
C
Date:
5
4
3
2
Document Number
Rev
1
AK4753
Wednesday, September 29, 2010
1
Sheet
2
of
5
5
4
3
2
1
47u L1
2
D3.3V
1
DVDD
PORT1
RX
3
GND
OUT
2
1
4118-VCC
U3
10u
0.1u
TORX147
D3.3V
+ C31
C30
C32
+
VCC
C33
10u
D3.3V
10k
R27
470
R28
10k
R29
470
1
2
3
4
5
6
7
0.1u
DGND
DGND
R30
10k
51
+
2
10
8
6
4
2
37
38
INT1
39
R
AVDD
41
R24
R25
2.2k
2.2k
PC-SCL
VCC
6A
6Y
5A
5Y
4A
4Y
14
13
12
11
10
9
8
SCL
C34
SDA
0.1u
PC-SDA
D
AK4753-PDN
74HC07
A1-10PA-2.54DSA
40
VSS3
1A
1Y
2A
2Y
3A
3Y
GND
PORT2
VCOM
42
RX0
NC
43
44
RX1
TEST1
46
RX2
VSS4
RX3
1
4118-VCC
45
C35
10u
48
R31
47
D
R26
INT0
36
OCKS0/CSN/CAD0
35
AK4118-OCKS0
OCKS1/CCLK/SCL
34
AK4118-OCKS1
IPS0/RX4
NC
EFR
DGND
9
7
5
3
1
SCL
SDA
SDA(ACK)
DGND
uP-I/F
D3.3V
3
AK4118-DIF0
DIF0/RX5
K
D3.3V
CM0/CDTO/CAD1
PDN
31
XTI
30
XTO
29
R32
D1
HSU119
DIF1/RX6
6
VSS1
7
DIF2/RX7
8
IPS1/IIC
10k
AK4118-PDN
A
33
32
LED1
LED2
STO
U4
AK4118A
1
3
ATE1D-2M3
AK4118-PDN
H
S1
2
L
AK4118-PDN
EFR
U5
1
2
3
4
5
6
7
C36
0.1u
C
DGND
9
P/SN
DAUX
28
10
XTL0
MCKO2
27
XTL1
BICK
26
SDTO
25
51
D2
HSU119
A
0.1u
C39
AK4753-SDTI
1
L
ATE1D-2M3
AK4753-PDN
R38
24
51
AK4753-LRCK
DIR
+
R40
C
C37
0.1u
DGND
10k
H
S2
C38
0.1u
DGND
S3
JP7
R39
EXT
DIR
MCKI
4118-VCC
D3.3V
R34
1k
EFR
JP6 AK4753-LRCK
EXT
10u
C42
+
51
3
R37
DIR
0.1u
C40
10u
C41
R33
1k
D3.3V
STO
JP5 AK4753-SDTI
LRCK
MCKO1
VSS2
22
23
DVDD
VOUT/GP7
21
20
COUT/GP5
UOUT/GP6
19
18
TX1/GP3
TX0/GP2
BOUT/GP4
17
16
15
DGND
14
13
TVDD
NC/GP1
VIN/GP0
14
13
12
11
10
9
8
R36
AK4753-BICK
EXT
12
VCC
6A
6Y
5A
5Y
4A
4Y
74HC14
K
R35
DIR
2
11
1A
1Y
2A
2Y
3A
3Y
GND
D3.3V
JP4 AK4753-BICK
EXT
DGND
K
CM1/CDTI/SDA
K
5
A
TEST2
A
4
AK4118-DIF1
51
D3.3V
5.1
8
7
6
5
4118-VCC
AK4753-MCLK
AK4753-MCLK
1
OCKS0
OCKS1
DIF0
DIF1
AK4118-OCKS0
AK4118-OCKS1
AK4118-DIF0
AK4118-DIF1
RP1
SW DIP-4
H
B
1
2
3
4
4
3
2
1
L
J7
B
MCKI
47k
2
3
4
5
DGND
DGND
D3.3V
DGND
R57
10k
10
8
6
4
2
9
7
5
3
1
U9
SDATA
LRCK
BICK
MCLK
PORT3
DGND
A1-10PA-2.54DSA
DSP
D3.3V
C68
0.1u
4
1A1
1B1
13
5
1A2
1B2
12
2
1DIR
1OE
15
6
2A1
2B1
11
STO
7
2A2
2B2
10
MUTEN
3
2DIR
2OE
14
1
VCCA
VCCB
16
8
GND
GND
9
D3.3V
C67
0.1u
74AVC4T245
DGND
A
JP18
JP17
MCLK
U10
4
1A1
1B1
13
5
1A2
1B2
12
2
1DIR
1OE
15
6
2A1
2B1
11
7
2A2
2B2
3
2DIR
2OE
14
SEL
D3.3V
C69
0.1u
A
10
1
VCCA
VCCB
16
8
GND
GND
9
D3.3V
C70
0.1u
Title
74AVC4T245
DGND
5
4
- 54 3
Size
A2
Date:
2
AKD4753-A
Document Number
Rev
1
DIR (AK4118)
Wednesday, September 29, 2010
1
Sheet
3
of
5
5
4
3
2
1
S4
1
2
DVDD
DVDD
4
3
EXTEE
BYPASS
SW DIP-2
H
EEPROM
R41
R42
R43
47k
2.2k
2.2k
L
R44
47k
U6
D
R45
47k
D
C66
0.1u
1
A0
VCC
8
2
A1
WP
7
3
A2
SCL
6
4
VSS
SDA
5
24LC01B
D3.3V
DGND
EESCL
JP8
PC-SCL
JP10
PC-SDA
PC-SCL
JP9
WP
EESDA
PC-SDA
DGND
C
C
+
+
USB-VDD
C43
10u
C44
10u
DGND
USB-RST
18
C47
0.1u
VDD1
VSS1
29
6
VSS0
MCLR_N/Vpp/RE3
12
13
33
34
NC/ICCK/ICPGC
NC/ICDT/ICPGD
NC/ICRST_N/ICVpp
NC/ICPORTS
30
31
OSC1/CLKI
OSC2/CLKO/RA6
25
26
27
RE0/AN5/CK1SPP
RE1/AN6/CK2SPP
RE2/AN7/OESPP
RB7/KBI3/PGD
RB6/KBI2/PGC
RB5/KBI1/PGM
RB4/AN11/KBI0/CSSPP
RB3/AN9/CPP2/VPO
RB2/AN8/INT2/VMO
RB1/AN10/INT1/SCK/SCL
RB0/AN12/INT0/FLT0/SDI/SDA
DGND
B
28
C46
0.1u
VDD0
U7
R47
100k
DGND
C45
0.1u
7
R46
4.7k
JP11
1
2
3
4
5
17
16
15
14
11
10
9
8
SILK-SCREEN
1: VDD
2: MCLR
3: PGD
4: PGC
5: GND
HEADER 5
DGND
B
C48 22p
C54
X2
20MHz
470n
37
PIC18F4550
TQFP 44-PIN
PC-SCL
PC-SDA
51
51
19
20
21
22
23
24
38
39
40
41
2
3
4
5
RC0/T1OSO/T13CKI
RC1/T1OSI/CCP2/UOE_N
RC2/CCP1/P1A
32
35
36
RC4/D-/VM
RC5/D+/VP
RC6/TX/CK
RC7/RX/DT/SDO
42
43
44
1
T1
+5V LM1084
1
+
VUSB
DGND
R48
R49
RD0/SPP0
RD1/SPP1
RD2/SPP2
RD3/SPP3
RD4/SPP4
RD5/SPP5/P1B
RD6/SPP6/P1C
RD7/SPP7/P1D
RA0/AN0
RA1/AN1
RA2/AN2/Vref-/CVref
RA3/AN3/Vref+
RA4/T0CKI/C1OUT/RCV
RA5/AN4/SS_N/HLVDIN/C2OUT
C51
C50
10u
0.1u
GND
C49 22p
IN
+3.3V
OUT
3
C52
2
XTI
XTO
+
0.1u
C53
10u
PORT4
DGND
R50
R51
1
2
3
4
22
22
VUSB
DD+
GND
A
A
USB(B type)
DGND
PIC18F4550
Title
AK4753-A
Size
B
Date:
5
4
3
- 55 -
2
Document Number
Rev
1
EEPROM
Wednesday, September 29, 2010
Sheet
1
4
of
5
5
4
3
2
1
D
D
T2
5V
8
7
6
5
+5V
C55
+
C56
0.1u
10u
3.3V
NC
NC
Vin
Vout
Vcont PCL
NC
GND
VSS1
1
2
3
4
VSS2
TK73633AME
C57
0.1u
+
C58
10u
R53
0
JP12
GND
VSS1
R54
0
DGND
VSS1
DGND
VSS1
AVDD
T3
LM1084
IN
OUT
(open)
C
(open)
C61
C60
C62
(open)
(open)
+5V
J8
1
+
2
AVDD
1
TJ-563 (RED)
DVDD
+
C59
47u
C63
J9
(open)
1
TJ-563 (RED)
2
+
L2
(short)
3
2
(open)
R56
3.3V
1
GND
5V
1
R55
JP13
AVDD
VSS1
C
AVDD
J10
1
TJ-563 (RED)
DVDD
VSS1
JP14
DVDD
L3
(short)
J11
2
DVDD
D3.3V
1
TJ-563 (RED)
1
1
+
2
C64
47u
VSS2
J12
AGND
1
TJ-563 (BLACK)
VCC
JP15
D3.3V
L4
(short)
2
B
VSS1
1
J13
DGND
D3.3V
1
TJ-563 (BLACK)
+
C65
B
DGND
47u
DGND
A
A
Title
Size
A3
- 56 -
Date:
5
4
3
2
AKD4753-A
Document Number
Rev
1
POWER
Wednesday, September 29, 2010
Sheet
1
5
of
5
- 57 -
- 58 -
- 59 -
- 60 -