BeRex BCT013 1500-4000 MHz Medium Power Amplifier Device Features • 45.0 dBm Output IP3 at 13dBm/tone • 15.0 dB Gain at 1900MHz • 27.5 dBm P1dB at 1900 MHz • Patented Over Voltage Protection Circuit •Application: commercial Target Device Performance (Ta = 25°C) Symbols Gain S11 S22 OIP3 P1dB NF Ic Vc Rth Parameters Test Conditions 1900MHz 2140MHz 2400MHz 3500MHz 1900MHz 2140MHz 2400MHz 3500MHz 1900MHz 2140MHz 2400MHz 3500MHz 1900MHz 2140MHz 2400MHz 3500MHz 1900MHz 2140MHz 2400MHz 3500MHz 1900MHz 2140MHz 2400MHz 3500MHz Vc = 5.0V Min Typ 14.0 13.0 12.2 9.7 15.1 14.0 13.3 10.7 -17.3 -12.0 -12.8 -25.3 -12.8 -12.0 -12.9 -25.3 45.0 45.2 43.1 40.2 27.5 27.1 27.2 25.9 42 42 40 37 26.5 26.2 26.0 25.0 Max dB dB dB dBm dBm 6.8 118 Thermal Resistance 138 5.0 50 Unit dB 158 mA V °C/W Test conditions unless otherwise noted. 1. T = 25°C, Vdevice = 5.0V, 50 ohm system. 2. OIP3 is measured on an eval-board with two tones separated by 1 MHz. http: //www.berex.com Confidential BeRex BCT013 Absolute Maximum Ratings Parameter Rating Operating Case temperature Storage Temperature Junction Temperature Supply Voltage Input RF Power -40 to +85°C -40 to +155°C +250°C 7V 23dBm Operation of this device above any of these parameters may result in permanent damage. Typical Device Data S-parameters (Vc=5V, Ic=138mA, T=25°C) -25 -30 S12 [dB] S(1,1) -35 m2 freq=4.000GHz m1 freq=50.00MHz -40 -45 -50 -55 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency [GHz] freq (50.00MHz to 4.000GHz) 14 12 m2 freq=4.000GHz 8 6 S(2,2) S21 [dB] 10 4 2 m1 freq=50.00MHz 0 -2 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Frequency [GHz] freq (50.00MHz to 4.000GHz) http: //www.berex.com Confidential BeRex BCT013 S-parameter test circuit Generic PF083 Evaluation Board I-V Characteristics PCB 31mil thick FR-4 • Current drop in between 5~6V is due to patented protection circuit. http: //www.berex.com Confidential BeRex BCT013 S-Parameter (5V/135mA) Freq [MHz] S11 [Mag] S11 [Ang] S21 [Mag] S21 [Ang] S12 [Mag] S12 [Ang] S22 [Mag] S22 [Ang] 100 500 1000 1500 2000 2500 3000 3500 4000 -0.046 -0.952 -1.111 -0.928 -1.240 -1.390 -1.669 -1.989 -2.281 -30.149 -116.77 -162.01 157.99 129.31 104.6 82.694 60.455 37.752 2.219 6.737 13.26 10.718 9.181 8.334 6.491 6.124 5.024 -128.4 -174.18 161.56 121.35 101.55 81.201 66.725 51.795 33.795 -41.958 -32.703 -32.513 -30.171 -28.599 -26.76 -26.706 -25.792 -24.653 66.107 25.318 76.255 46.516 42.527 37.808 32.623 26.141 20.698 -3.497 -3.457 -7.557 -7.780 -7.262 -7.180 -7.38 -7.336 -6.823 165.97 162.64 117.5 127.17 116.25 97.537 74.648 50.666 32.131 Application Circuit: 1900 MHz Schematic Diagram BOM Vcc L1 C1 C2 C3 C1 Tolerance 100pF ±5% C2 1000pF ±5% C3 10uF ±15% C4 22pF ±5% C5 22pF ±5% C6 3.0pF ±5% C7 0.5pF ±5% L1 100nH ±5% BT013 RF In C4 C5 C6 RF Out C7 Note: 1. Chip is mounted on the PF083 open PKG, and bonded with 2-wires at both input and output. 2. PCB: 31mil thick FR4 3. Distance between the center of the shunt cap(C6) and the input pin of BT013 is 3.2mm 4. Distance between the center of the shunt cap(C7) and the output pin of BT03 is 8.3mm http: //www.berex.com Confidential BeRex BCT013 Typical Performance http: //www.berex.com Confidential BeRex BCT013 Application Circuit: 2100 MHz Schematic Diagram Vcc L1 C1 C2 C3 BT013 RF In C4 C5 C6 RF Out C7 C1 BOM 100pF Tolerance ±5% C2 1000pF ±5% C3 10uF ±15% C4 24pF ±5% C5 24pF ±5% C6 3pF ±5% C7 0.5pF ±5% L1 33nH ±5% Note: 1. Chip is mounted on the PF083 open PKG, and bonded with 2-wires at Both input and output. 2. PCB: 31mil thick FR4 3. Distance between the center of the shunt cap(C6) and the input pin of BT013 is 1.5mm 4. Distance between the center of the shunt cap(C7) and the output pin of BT03 is 6.4mm http: //www.berex.com Confidential BeRex BCT013 Typical Performance http: //www.berex.com Confidential BeRex BCT013 Application Circuit: 2400MHz Schematic Diagram BOM C1 Tolerance 100pF ±5% C2 1000pF ±5% C3 10uF ±15% C4 100pF ±5% C5 100pF ±5% C6 2pF ±5% C7 0.5pF ±5% L1 33nH ±5% Note: 1. Chip is mounted on the PF083 open PKG, and bonded with 2-wires at Both input and output. 2 PCB: 31mil thick FR4 3 Distance between the center of the shunt cap(C6) and the input pin of BT013 is 0.7mm 4 Distance between the center of the shunt cap(C7) and the output pin of BT03 is 3.2mm http: //www.berex.com Confidential BeRex BCT013 Typical Performance http: //www.berex.com Confidential BeRex BCT013 Application Circuit: 3500MHz Schematic Diagram BOM Tolerance C1 22pF ±5% C2 0.75pF ±5% C3 0.5pF ±5% C4 100pF ±5% C5 1000pF ±5% C6 10uF ±20% C7 0.5pF ±5% C8 22pF ±5% L1 33nH ±5% Note: 1. Chip is mounted on the PF083 open PKG, and bonded with 2-wires at both input and output. 2 PCB: 31mil thick FR4 3 Distance between the center of the shunt cap(C2) and the input pin of BT013 is 10mm 4 Distance between the center of the series cap(C3) and the input pin of BT013 is 4mm 5 Distance between the center of the shunt cap(C7) and the output pin of BT03 is 3mm http: //www.berex.com Confidential BeRex BCT013 Typical Performance http: //www.berex.com Confidential BeRex BCT013 Die Outline NOTES: 1) DIE THICKNESS 100um 2) BONDPAD METAL THICKNESS 2.8um 3) BACKSIDE METAL Au, 5um 4) DEVICE IS GROUNDED THROUGH VIA HOLES MSL / ESD Rating ESD Rating Value Test Standard Class 1 Passes <1000V Human Body Model (HBM) JEDEC Standard JESD22-A114B MSL Rating Standard Level 1 at +265°C convection reflow JEDEC Standard J-STD-020 http: //www.berex.com Confidential BeRex BCT013 NATO CAGE code: 2 N 9 6 F NOTICE BeRex Corporation reserves the right to make changes of product specification or to discontinue product at any time without notice. http: //www.berex.com Confidential