Data Sheet Comlinear AD8052LV ® General Description The COMLINEAR AD8052LV is a low cost dual, voltage feedback amplifier. This amplifier is designed to operate on +2.7V to +5V, or ±2.5V supplies. The input voltage range extends 300mV below the negative rail and 1.2V below the positive rail. The AD8052LV offers superior dynamic performance with a 260MHz small signal bandwidth and 145V/μs slew rate. The combination of low power, high output current drive, and rail-to-rail performance make the AD8052LV well suited for battery-powered communication/computing systems. The combination of low cost and high performance make the AD8052LV suitable for high volume applications in both consumer and industrial applications such as wireless phones, scanners, and color copiers. APPLICATIONS n A/D driver n Active filters n CCD imaging systems n CD/DVD ROM n Coaxial cable drivers n High capacitive load driver n Portable/battery-powered applications n Twisted pair driver n Telecom and optical terminals n Video driver Output Swing Output Voltage (0.5V/div) 2.7 Vs = +2.7V RL = 2kΩ G = -1 0 Time (0.5μs/div) ® FEATURES n 260MHz bandwidth n Fully specified at +2.7V and +5V supplies n Output voltage range: 0.036V to 4.953V; Vs = +5; RL = 2kΩ n Input voltage range: -0.3V to +3.8V; Vs = +5 n 145V/μs slew rate n 4.2mA supply current per amplifier n ±55mA linear output current n ±85mA short circuit current n Directly replaces AD8052, AD8042 and AD8092 in single supply applications n Pb-free SOIC-8 package Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier Rev 1A Ordering Information Part Number Package Pb-Free RoHS Compliant Operating Temperature Range Packaging Method AD8052LVISO8 SOIC-8 Yes Yes -40°C to +85°C Rail AD8052LVISO8X SOIC-8 Yes Yes -40°C to +85°C Reel AD8052LVIMP8X* MSOP-8 Yes Yes -40°C to +85°C Reel Moisture sensitivity level for all parts is MSL-1. *Advance Information, contact CADEKA for availability. ©2011 CADEKA Microcircuits LLC www.cadeka.com Data Sheet AD8052LV Pin Configuration AD8052LV Pin Assignments SOIC-8, MSOP-8 SOIC-8, MSOP-8 1 -IN1 2 +IN1 3 -Vs 4 + + 8 +Vs 7 OUT2 6 -IN2 5 +IN2 Pin No. Pin Name Description 1 OUT1 Output, channel 1 2 -IN1 Negative input, channel 1 3 +IN1 Positive input, channel 1 4 -VS 5 +IN2 Positive input, channel 2 6 -IN2 Negative input, channel 2 7 OUT2 Output, channel 2 8 +VS Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier OUT1 Negative supply ® Positive supply Rev 1A ©2011 CADEKA Microcircuits LLC www.cadeka.com 2 Data Sheet Absolute Maximum Ratings Parameter Max Unit 0 -Vs -0.5V +6 +Vs +0.5V V V ® Supply Voltage Input Voltage Range Min Reliability Information Parameter Junction Temperature Storage Temperature Range Lead Temperature (Soldering, 10s) Package Thermal Resistance 8-Lead SOIC 8-Lead MSOP Min Typ -65 Max Unit 175 150 260 °C °C °C 100 TBD °C/W °C/W Notes: Package thermal resistance (θJA), JDEC standard, multi-layer test boards, still air. ESD Protection Product Human Body Model (HBM) Charged Device Model (CDM) SOIC-8 MSOP-8 2.5kV 2kV TBD TBD Recommended Operating Conditions Parameter Min Operating Temperature Range Supply Voltage Range -40 2.5 Typ Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the operating conditions noted on the tables and plots. Max Unit +85 5.5 °C V Rev 1A ©2011 CADEKA Microcircuits LLC www.cadeka.com 3 Data Sheet Electrical Characteristics at 2.7V Vs = +2.7V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response -3dB Bandwidth(2) G = +1, VOUT = 0.05Vpp 215 MHz BWSS -3dB Bandwidth G = +2, VOUT = 0.2Vpp 85 MHz BWLS Large Signal Bandwidth G = +2, VOUT = 2Vpp 36 MHz GBWP Gain Bandwidth Product 86 MHz ® Time Domain Response tR, tF Rise and Fall Time(2) VOUT = 0.2V step 3.7 ns tS Settling Time to 0.1% VOUT = 1V step 40 ns OS Overshoot VOUT = 0.2V step 9 % SR Slew Rate 2.7V step, G = -1 130 V/µs 1Vpp, 5MHz 79 dBc 1Vpp, 5MHz 82 dBc Distortion/Noise Response HD2 2nd Harmonic Distortion(2) HD3 3rd Harmonic Distortion(2) 1Vpp, 5MHz 77 dB en Input Voltage Noise > 1MHz 16 nV/√Hz in Input Current Noise > 1MHz 1.3 pA/√Hz XTALK Crosstalk(1) 10MHz 65 dB Input Offset Voltage -1.6 mV µV/°C DC Performance VIO dVIO Average Drift 10 Ib Input Bias Current 3 µA dIb Average Drift 7 nA/°C IIO Input Offset Current 0.1 µA PSRR Power Supply Rejection Ratio(1) 57 dB AOL Open-Loop Gain 75 dB IS Quiescent Current 3.9 mA 4.3 MΩ 1.8 pF DC 52 Per Amplifier Input Characteristics RIN Input Resistance CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio -0.3 to 1.5 V 87 dB RL = 10kΩ to Vs/2 0.023 to 2.66 V RL = 2kΩ to Vs/2 0.025 to 2.653 V RL = 150Ω to Vs/2 0.065 to 2.55 V ±55 mA ±50 mA ±85 mA DC, Vcm = 0V to Vs -1.5 Output Characteristics VOUT Output Voltage Swing Output Current ISC Short-Circuit Output Current Vs Power Supply Operating Range -40°C to +85°C 2.5 2.7 5.5 Rev 1A IOUT V Notes: 1. 100% tested at 25°C. 2. Rf = 1kΩ was used for optimal performance. (For G = +1, Rf = 0). ©2011 CADEKA Microcircuits LLC Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier UGBW www.cadeka.com 4 Data Sheet Electrical Characteristics at 5V Vs = 5V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response -3dB Bandwidth(2) G = +1, VOUT = 0.05Vpp 260 MHz BWSS -3dB Bandwidth G = +2, VOUT = 0.2Vpp 90 MHz BWLS Large Signal Bandwidth G = +2, VOUT = 2Vpp 40 MHz GBWP Gain Bandwidth Product 90 MHz ® Time Domain Response tR, tF Rise and Fall Time(2) VOUT = 0.2V step 3.6 ns tS Settling Time to 0.1% VOUT = 2V step 40 ns OS Overshoot VOUT = 0.2V step 7 % SR Slew Rate 5V step, G = -1 145 V/µs 2Vpp, 5MHz 71 dBc 2Vpp, 5MHz 78 dBc 2Vpp, 5MHz 70 dB NTSC (3.85MHz), AC-Coupled, RL = 150Ω 0.06 % NTSC (3.85MHz), DC-Coupled, RL = 150Ω 0.08 % NTSC (3.85MHz), AC-Coupled, RL = 150Ω 0.07 ° NTSC (3.85MHz), DC-Coupled, RL = 150Ω 0.06 ° Distortion/Noise Response HD2 HD3 DG 2nd Harmonic Distortion(2) 3rd Harmonic Distortion(2) Differential Gain DP Differential Phase en Input Voltage Noise >1MHz 16 nV/√Hz in Input Current Noise >1MHz 1.3 pA/√Hz XTALK Crosstalk(2) 10MHz 62 dB DC Performance VIO dVIO Ib dIb IIO Input Offset Voltage(1) -8 Average Drift -8 Average Drift Power Supply Rejection Open-Loop Gain(1) IS Quiescent Current(1) +8 3 Ratio(1) DC -0.8 0.1 52 57 68 78 Per Amplifier 4.2 mV µV/°C +8 7 Input Offset Current(1) AOL 1.4 10 Input Bias Current(1) PSRR µA nA/°C +0.8 µA dB dB 5.2 mA Input Characteristics RIN Input Resistance 4.3 MΩ CIN Input Capacitance 1.8 pF CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio(1) -0.3 to 3.8 V 87 dB RL = 10kΩ to Vs/2 0.027 to 4.97 V RL = 2kΩ to Vs/2 0.036 to 4.953 DC, Vcm = 0V to Vs -1.5 72 Output Characteristics Output Voltage Swing RL = 150Ω to Vs/2(1) IOUT Output Current ISC Short-Circuit Output Current Vs Power Supply Operating Range 0.3 -40°C to +85°C 0.12 to 4.8 V 4.625 V ±55 mA ±50 mA ±85 2.5 5 Rev 1A VOUT mA 5.5 V Notes: 1. 100% tested at 25°C. 2. Rf = 1kΩ was used for optimal performance. (For G = +1, Rf = 0). ©2011 CADEKA Microcircuits LLC Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier UGBW www.cadeka.com 5 Data Sheet Typical Performance Characteristics Vs = +5V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. G=5 Rf = 2kΩ 0.1 1 10 100 G = -1 Rf = 2kΩ G = -10 Rf = 2kΩ G = -5 Rf = 2kΩ G = -2 Rf = 2kΩ 0.1 Frequency (MHz) G=2 Rf = 1kΩ G = 10 Rf = 2kΩ G=5 Rf = 2kΩ 1 10 100 G = -10 Rf = 2kΩ G = -5 Rf = 2kΩ G = -2 Rf = 2kΩ 0.1 0.1 Magnitude (1dB/div) - CL = 20pF Rs = 20Ω CL 1kΩ 1kΩ 1 RL CL = 10pF Rs = 0Ω 10 Frequency (MHz) ©2011 CADEKA Microcircuits LLC 100 100 0.1 Vo = 1Vpp Rev 1A CL = 50pF Rs = 33Ω Rs 10 Large Signal Frequency Response CL = 100pF Rs = 25Ω + 1 Frequency (MHz) Frequency Response vs. CL Magnitude (1dB/div) 100 G = -1 Rf = 2kΩ Frequency (MHz) 10 Inverting Frequency Response Vs = +2.7V Normalized Magnitude (1dB/div) G=1 Rf = 0 0.1 1 Frequency (MHz) Non-Inverting Frequency Response Vs = +2.7V Normalized Magnitude (2dB/div) ® G = 10 Rf = 2kΩ Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier G=1 Rf = 0 G=2 Rf = 1kΩ Inverting Frequency Response Vs = +5V Normalized Magnitude (1dB/div) Non-Inverting Frequency Response Vs = +5V Normalized Magnitude (2dB/div) Vo = 2Vpp 1 10 100 Frequency (MHz) www.cadeka.com 6 Data Sheet Typical Performance Characteristics Vs = +5V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. Frequency Response vs. Temperature Input Voltage Noise Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier 100 Magnitude (0.5dB/div) 80 70 60 ® Voltage Noise (nV/√Hz) 90 50 40 30 20 10 0 1 10 1k 100 10k 2nd & 3rd Harmonic Distortion; Vs = +5V -20 -30 Distortion (dBc) -20 Vo = 2Vpp Rf = 1kΩ 2nd RL = 150Ω -40 3rd RL = 150Ω -60 2nd RL = 2kΩ 3rd RL = 2kΩ -80 -90 0 5 Vo = 1Vpp Rf = 1kΩ -30 -50 -70 3rd RL = 150Ω -40 -50 2nd RL = 150Ω -60 15 -90 20 3rd RL = 2kΩ 0 5 Frequency (MHz) -20 Rf = 1kΩ Rf = 1kΩ -50 Distortion (dBc) 20MHz 10MHz -60 -70 5MHz -80 2MHz 1.0 1.5 2.0 Output Amplitude (Vpp) ©2011 CADEKA Microcircuits LLC 20MHz -40 -50 10MHz -60 -70 5MHz -80 2.5 Rev 1A Distortion (dBc) 20 -30 -40 0.5 15 3rd Harmonic Distortion vs. Vo -20 -90 10 Frequency (MHz) 2nd Harmonic Distortion vs. Vo -30 2nd RL = 2kΩ -70 -80 10 1M 2nd & 3rd Harmonic Distortion; Vs = +2.7V Distortion (dBc) 100k Frequency (Hz) Frequency (MHz) 2MHz -90 0.5 1.0 1.5 2.0 2.5 Output Amplitude (Vpp) www.cadeka.com 7 Data Sheet Typical Performance Characteristics Vs = +5V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. PSRR CMRR 0 -10 Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier -40 -50 CMRR (dB) -30 -40 -60 ® PSRR (dB) -20 -70 -50 -80 -60 -70 1k 0.01 0.1 1 -90 0.01 100 10 0.1 Frequency (MHz) Open Loop Gain & Phase vs. Frequency 0.8 70 0.6 60 |Gain| 40 30 20 10 0 Phase -45 0 -90 -10 -20 0.01 0.1 1 10 100 Output Voltage (V) 80 50 Linear output current ±55mA 0.2 0 -0.2 Short circuit current ±85mA -0.4 -135 -0.6 -180 -0.8 -100 ©2011 CADEKA Microcircuits LLC 50 100 Rf = 1kΩ Rev 1A Time (20ns/div) 0 Small Signal Pulse Response Vs = +2.7V Output Voltage (0.05V/div) Rf = 1kΩ -50 Output Current (mA) Small Signal Pulse Response Vs = +5V Output Voltage (0.05V/div) 100 0.4 Frequency (MHz) 10 Output Current Phase (degrees) Open Loop Gain (dB) 1.0 Frequency (MHz) Time (20ns/div) www.cadeka.com 8 Data Sheet Typical Performance Characteristics Vs = +5V, G = 2, Rf = 2kΩ, RL = 2kΩ to Vs/2; unless otherwise noted. Large Signal Pulse Response Vs = +5V Output Swing Output Voltage (0.5V/div) Output Voltage (0.5V/div) ® Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier 2.7 Rf = 1kΩ Vs = +2.7V RL = 2kΩ G = -1 0 Time (20ns/div) Time (0.5μs/div) Channel Matching Vs = +5V Rf = 1kΩ RL = 2kΩ G=2 Magnitude (0.5dB/div) Channel 1 Channel 2 0.1 1 10 100 Frequency (MHz) Rev 1A ©2011 CADEKA Microcircuits LLC www.cadeka.com 9 Data Sheet Application Information +Vs General Description R1 Input +Vs Output - RL Rf 6.8μF ® Figures 1, 2, and 3 illustrate typical circuit configurations for non-inverting, inverting, and unity gain topologies for dual supply applications. They show the recommended bypass capacitor values and overall closed loop gain equations. Figure 4 shows the typical non-inverting gain circuit for single supply applicaitons. 0.1μF + 0.1μF The common mode input range extends to 300mV below ground and to 1.2V below Vs. Exceeding these values will not cause phase reversal. However, if the input voltage exceeds the rails by more than 0.5V, the input ESD devices will begin to conduct. The output will stay at the rail during this overdrive condition. The design uses a Darlington output stage. The output stage is short circuit protected and offers “soft” saturation protection that improves recovery time. Rg Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier The AD8052LV is a single supply, general purpose, voltage-feedback amplifier fabricated on a complementary bipolar process using a patent pending topography. They feature a rail-to-rail output stage and is unity gain stable. Both gain bandwidth and slew rate are insensitive to temperature. 6.8μF G = - (Rf/Rg) -Vs For optimum input offset voltage set R1 = Rf || Rg Figure 2. Typical Inverting Gain Circuit +Vs Input 6.8μF 0.1μF + Output - RL 0.1μF 6.8μF -Vs G=1 Figure 3. Unity Gain Circuit 6.8μF +Vs 6.8μF + Input 0.1μF + Output 0.1μF Rg 6.8μF -Vs In + RL - Rf G = 1 + (Rf/Rg) 0.01µF Out Rf Rg Figure 1. Typical Non-Inverting Gain Circuit Rev 1A Figure 4. Single Supply Non-Inverting Gain Circuit ©2011 CADEKA Microcircuits LLC www.cadeka.com 10 Data Sheet The effective load resistor (Rloadeff) will need to include the effect of the feedback network. For instance, Rloadeff in Figure 3 would be calculated as: RL || (Rf + Rg) G=2 RL = 2kΩ Vs = +5V Rf = 2kΩ These measurements are basic and are relatively easy to perform with standard lab equipment. For design purposes however, prior knowledge of actual signal levels and load impedance is needed to determine the dissipated power. Rf = 1kΩ Here, PD can be found from PD = PQuiescent + PDynamic - PLoad 1 10 100 Frequency (MHz) Figure 5: Frequency Response vs. Rf Quiescent power can be derived from the specified IS values along with known supply voltage, VSupply. Load power can be calculated as above with the desired signal amplitudes using: Power Dissipation Power dissipation should not be a factor when operating under the stated 2kΩ load condition. However, applications with low impedance, DC coupled loads should be analyzed to ensure that maximum allowed junction temperature is not exceeded. Guidelines listed below can be used to verify that the particular application will not cause the device to operate beyond it’s intended operating range. Maximum power levels are set by the absolute maximum junction rating of 150°C. To calculate the junction temperature, the package thermal resistance value ThetaJA (ӨJA) is used along with the total die power dissipation. TJunction = TAmbient + (ӨJA × PD) (VLOAD)RMS = VPEAK / √2 ( ILOAD)RMS = ( VLOAD)RMS / Rloadeff The dynamic power is focused primarily within the output stage driving the load. This value can be calculated as: PDYNAMIC = (VS+ - VLOAD)RMS × ( ILOAD)RMS Assuming the load is referenced in the middle of the power rails or Vsupply/2. The AD8052LV is short circuit protected. However, this may not guarantee that the maximum junction temperature (+150°C) is not exceeded under all conditions. Figure 6 shows the maximum safe power dissipation in the package vs. the ambient temperature for the packages available. 2.5 PD = Psupply - Pload Supply power is calculated by the standard power equation. Psupply = Vsupply × IRMS supply Vsupply = VS+ - VSPower delivered to a purely resistive load is: ©2011 CADEKA Microcircuits LLC 2 Rev 1A In order to determine PD, the power dissipated in the load needs to be subtracted from the total power delivered by the supplies. Maximum Power Dissipation (W) Where TAmbient is the temperature of the working environment. ® Magnitude (1dB/div) Pload = ((VLOAD)RMS2)/Rloadeff Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier At non-inverting gains other than G = +1, keep Rg below 1kΩ to minimize peaking; thus, for optimum response at a gain of +2, a feedback resistor of 1kΩ is recommended. Figure 5 illustrates the AD8052LV frequency response with both 1kΩ and 2kΩ feedback resistors. 1.5 SOIC-8 1 0.5 0 -40 -20 0 20 40 60 80 Ambient Temperature (°C) Figure 6. Maximum Power Derating www.cadeka.com 11 Data Sheet Increased phase delay at the output due to capacitive loading can cause ringing, peaking in the frequency response, and + Rs - Time (20ns/div) Output CL Rf Output ® Input RL = 2kΩ Vin =2Vpp G=5 Rf = 1kΩ Input RL Figure 8. Overdrive Recovery Rg Layout Considerations Figure 7. Addition of RS for Driving Capacitive Loads Table 1 provides the recommended RS for various capacitive loads. The recommended RS values result in approximately <1dB peaking in the frequency response. General layout and supply bypassing play major roles in high frequency performance. CADEKA has evaluation boards to use as a guide for high frequency layout and as an aid in device testing and characterization. Follow the steps below as a basis for high frequency layout: ▪▪Include 6.8µF and 0.1µF ceramic capacitors for power supply decoupling CL (pF) RS (Ω) -3dB BW (kHz) 10pF 0 100 20pF 20 94 50pF 33 72 100pF 25 58 Table 1: Recommended RS vs. CL For a given load capacitance, adjust RS to optimize the tradeoff between settling time and bandwidth. In general, reducing RS will increase bandwidth at the expense of additional overshoot and ringing. An overdrive condition is defined as the point when either one of the inputs or the output exceed their specified voltage range. Overdrive recovery is the time needed for the amplifier to return to its normal or linear operating point. The recovery time varies, based on whether the input or output is overdriven and by how much the range is exceeded. The AD8052LV will typically recover in less than 20ns from an overdrive condition. Figure 8 shows the AD8052LV in an overdriven condition. ©2011 CADEKA Microcircuits LLC ▪▪Place the 6.8µF capacitor within 0.75 inches of the power pin ▪▪Place the 0.1µF capacitor within 0.1 inches of the power pin ▪▪Remove the ground plane under and around the part, especially near the input and output pins to reduce parasitic capacitance ▪▪Minimize all trace lengths to reduce series inductances Refer to the evaluation board layouts below for more information. Evaluation Board Information The following evaluation boards are available to aid in the testing and layout of these devices: Evaluation Board # CEB006 CEB010 Products AD8052LV in SOIC AD8052LV in MSOP www.cadeka.com 12 Rev 1A Overdrive Recovery Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier possible unstable behavior. Use a series resistance, RS, between the amplifier and the load to help improve stability and settling performance. Refer to Figure 7. Input Voltage (0.5V/div) Driving Capacitive Loads Data Sheet Evaluation Board Schematics Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier Evaluation board schematics and layouts are shown in Figures 9-13. These evaluation boards are built for dualsupply operation. Follow these steps to use the board in a single-supply application: 1. Short -Vs to ground. ® 2. Use C3 and C4, if the -VS pin of the amplifier is not directly connected to the ground plane. Figure 11. CEB006 Bottom View Figure 12. CEB010 Top View Figure 10. CEB006 Top View Figure 13. CEB010 Bottom View Rev 1A Figure 9. CEB006 & CEB010 Schematic ©2011 CADEKA Microcircuits LLC www.cadeka.com 13 Data Sheet Mechanical Dimensions SOIC-8 Package ® Comlinear AD8052LV Low Cost, +2.7V to 5.5V, 260MHz Rail-to-Rail Amplifier MSOP-8 Package 3.00±0.10 (0.45) 0.65 A B (1.30) (5.50) (4.20) 4.90±0.15 3.00±0.10 PIN #1 ID QUADRANT LAND PATTERN RECOMMENDATION SEE DETAIL A TOP VIEW 1.10MAX 0.65 0.150 0.050 0.380 C 0.270 SIDE VIEW 0.10 0.23 0.13 12° TOP & BOTTOM A B C Gauge Plane Seating Plane 0.25 0.70 0.40 0.95 DETAIL A For additional information regarding our products, please visit CADEKA at: cadeka.com CADEKA Headquarters Loveland, Colorado T: 970.663.5452 T: 877.663.5452 (toll free) CADEKA, the CADEKA logo design, Comlinear, and the Comlinear logo design are trademarks or registered trademarks of CADEKA Microcircuits LLC. All other brand and product names may be trademarks of their respective companies. CADEKA reserves the right to make changes to any products and services herein at any time without notice. CADEKA does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by CADEKA; nor does the purchase, lease, or use of a product or service from CADEKA convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of CADEKA or of third parties. Copyright ©2011 by CADEKA Microcircuits LLC. All rights reserved. 8° 0° Rev 1A NOTES: A. CONFORMS TO JEDEC MO-187 B, DIMENSIONS ARE IN MM C. DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS D. DIMENSIONS AND TOLERANCES ARE PER ASME Y14.5M, 1994 E LANDPATTERN AS PER IPC7351 #TSOP65P490X110-8BL MKT-MUA08AREVB END VIEW