Preliminary October 22, 2010 Cree® XLamp® XM-L LEDs Data Sheet FEATURES • Maximum drive current: 3000 mA • Low thermal resistance: 2.5°C/W • Maximum junction temperature: 150°C • Viewing angle: 125° • Available in cool white • ANSI-compatible chromaticity bins • Unlimited floor life at ≤ 30ºC/85% RH • Reflow solderable - JEDEC J-STD-020C • Electrically neutral thermal path ev 0 CLD-DS33 R Data Sheet: Table of Contents Flux Characteristics (TJ = 25°C).................................................................................................. 2 Characteristics......................................................................................................................... 2 Relative Spectral Power Distribution............................................................................................ 3 Relative Flux vs. Junction Temperature (IF = 700 mA).................................................................... 3 Electrical Characteristics (TJ = 25°C)........................................................................................... 4 Relative Flux vs. Current (TJ = 25°C).......................................................................................... 5 Typical Spatial Distribution......................................................................................................... 5 Reflow Soldering Characteristics................................................................................................. 6 Notes...................................................................................................................................... 7 Performance Groups – Brightness............................................................................................... 8 Cree’s Standard Chromaticity Regions Plotted on the 1931 CIE Curve............................................ 10 Standard Order Codes and Bins (XM-L ANSI Cool White).............................................................. 11 Mechanical Dimensions........................................................................................................... 12 This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 1 Preliminary October 22, 2010 Flux Characteristics (TJ = 25°C) The following table provides several base order codes for XLamp XM-L LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. CCT Range Color Min. Cool White 5,000 K Max. 8,300 K Base Order Codes Min Luminous Flux @ 700 mA (lm) Order Code Group Flux (lm) T5 260 XMLAWT-00-0000-0000T5051 T6 280 XMLAWT-00-0000-0000T6051 Notes: • Cree maintains a tolerance of +/- 7% on flux and power measurements and +/- 2% on CRI measurements. • Typical CRI for Cool White (5,000 K - 8,300 K CCT) is 75. Characteristics Characteristics Thermal Resistance, junction to solder point Viewing Angle (FWHM) Temperature coefficient of voltage Unit Minimum °C/W 2.5 degrees 125 mV/°C -3.0 ESD Classification (HBM per Mil-Std-883D) DC Forward Current Typical Maximum Class 2 mA 3000 Reverse Voltage V 5 Forward voltage (@ 700 mA) V 2.9 Forward voltage (@ 1500 mA) V 3.1 Forward voltage (@ 3000 mA) V 3.35 LED Junction Temperature °C Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 2 CLD-DS33 Rev 0 3.5 150 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Relative Spectral Power Distribution Relative Radiant Power (%) 100 Relative Spectral Power 80 60 5000K - 8300K CCT 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) Relative Flux vs. Junction Temperature (IF = 700 mA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 3 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Electrical Characteristics (Tj = 25ºC) Electrical Characteristics (TJ = 25°C) 3000 2800 2600 Forward Current (mA) 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 Forward Voltage (V) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to Cool White ambient in order to optimize lamp life and optical characteristics. 3500 Maximum Current (mA) 3000 2500 2000 1500 Thermal Design 1000 Rj-a = 4°C/W Rj-a = 7°C/W Rj-a = 10°C/W 500 Rj-a = 15°C/W 0 0 20 40 60 80 100 120 140 Ambient Temperature (ºC) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 4 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Relative Flux vs. Current (TJ = 25°C) 350% Relative Luminous Flux (%) 325% 300% 275% 250% 225% 200% 175% 150% 125% 100% 75% Spatial Radiation Pattern Typical 50% 25% 0% 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 Forward Current (mA) Typical Spatial Distribution Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (º) Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 5 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3°C/second max. 3°C/second max. Preheat: Temperature Min (Tsmin) 100°C 150°C Preheat: Temperature Max (Tsmax) 150°C 200°C 60-120 seconds 60-180 seconds 183°C 217°C 60-150 seconds 60-150 seconds 215°C 260°C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 6 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Notes Lumen Maintenance Projections Cree currently recommends a maximum drive current of 1500 mA for XLamp XM-L white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating (≥ 94.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating (≥ 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp XM-L LEDs to have unlimited floor life in conditions ≤30ºC / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85ºC / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 7 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Performance Groups – Brightness XLamp XM-L LEDs are tested for luminous flux and placed into one of the following luminous-flux groups: Group Code Min. Luminous Flux @ 700 mA (lm) Max. Luminous Flux @ 700 mA (lm) T5 260 280 T6 280 300 U2 300 320 Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 8 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Performance Groups – Chromaticity Region 0A 0R 1A 1R 2A 2R 3A 3R x y 0.2950 0.2920 0.2984 0.3133 0.3009 0.2980 0.2950 0.2970 0.3009 0.3042 0.3037 Region x y 0.2970 0.2920 0.3060 0.2895 0.2962 0.3220 0.3042 0.2984 0.2880 0.2895 0.2870 0.3210 0.2937 0.3312 0.2937 0.2962 0.3220 0.3048 0.3207 0.3028 0.3130 0.3290 0.3115 0.3144 0.3186 0.3130 0.3290 0.3068 0.3113 0.3048 0.3207 0.3068 0.3113 0.3005 0.3415 0.3144 0.3186 0.3099 0.3509 0.3161 0.3059 0.3115 0.3391 0.3093 0.2993 0.3028 0.3215 0.3350 0.3207 0.3290 0.3417 0.3290 0.3538 0.3290 0.3300 0.3290 0.3417 0.3222 0.3243 0.3215 0.3350 0.3222 0.3243 0.3196 0.3290 0.3300 0.3290 0.3290 0.3180 0.3290 0.3538 0.3231 0.3120 0.3207 0.3462 0.3371 0.3490 0.3376 0.3616 0.3451 0.3554 0.3463 0.3687 0.3440 0.3427 0.3451 0.3554 0.3366 0.3369 0.3371 0.3490 0.3366 0.3369 0.3381 0.3762 0.3440 0.3428 0.3480 0.3840 0.3429 0.3307 0.3463 0.3687 0.3361 0.3245 0.3376 0.3616 0B 0S 1B 1S 2B 2S 3B 3S Region x y 0.3060 0.2984 0.3135 0.2962 0.3028 0.3304 0.3133 0.3048 0.3135 0.2962 0.2937 0.3312 0.3005 0.3415 0.3028 0.3304 0.3304 0.3115 0.3391 0.3205 0.3213 0.3373 0.3130 0.3290 0.3099 0.3509 0.3196 0.3602 0.3205 0.3481 0.3304 0.3115 0.3462 0.3290 0.3376 0.3616 0.3371 0.3490 0.3290 0.3417 0.3602 0.3290 0.3690 0.3381 0.3376 0.3616 0.3290 0.3538 0C 0T 1C 1T 2C 2T x y 0.3133 0.2984 0.3133 0.3220 0.3048 0.3207 0.3068 0.3113 0.3207 0.3009 0.3042 0.3220 0.3037 0.2937 0.3009 0.3042 0.3068 0.3113 0.3093 0.2993 0.3391 0.3130 0.3290 0.3481 0.3213 0.3373 0.3221 0.3261 0.3144 0.3186 0.3144 0.3186 0.3221 0.3261 0.3231 0.3120 0.3391 0.3161 0.3059 0.3538 0.3290 0.3417 0.3371 0.3490 0.3366 0.3369 0.3290 0.3300 0.3690 0.3290 0.3300 0.3762 0.3366 0.3369 0.3361 0.3245 0.3290 0.3180 Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 9 CLD-DS33 Rev 0 Region 0D 0U 1D 1U 2D 2U Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Cree’s Standard Chromaticity Regions Plotted on the 1931 CIE Curve ANSI Cool White 0.40 5000K 0.39 0.38 5700K 3S 0.37 6500K 2T 0.36 0.35 2C 1T 8000K CCy 3B 2S 1S 0.34 0T 0.33 0S 0.32 0B 0.31 3R 2A 1D 2U ANSI C78.377A 2R 1A 1U 0D 0A 2D 1C 1B 0C 3A 2B 1R 0U 0.30 0R 0.29 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.28 CCx Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 10 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Preliminary October 22, 2010 Standard Order Codes and Bins (XM-L ANSI Cool White) XLamp XM-L LED Standard Order Codes - White Min. Luminous Flux (lm) @ 700 mA* Chromaticity Regions Kit Number Group Flux (lm) T5 260 0A, 0B, 0C, 0D, 0R, 0S, 0T, 0U, 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 2U, 3A, 3B, 3R, 3S 0000T5051 T6 280 0A, 0B, 0C, 0D, 0R, 0S, 0T, 0U, 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 2U, 3A, 3B, 3R, 3S 0000T6051 ANSI Cool White (5000 K – 8300 K) For other flux and chromaticity combinations, contact Cree or an authorized distributor. * Cree XLamp XM-L order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity restrictions specified by the order code. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 11 CLD-DS33 Rev 0 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp C Preliminary October 22, 2010 Mechanical Dimensions 4.7 3.9 All measurements are ±.13 mm unless otherwise indicated. 0.6 B 6 5 4.7 0.4 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND 5 THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT NOTICE MAYTHE NOTINFORMATION BE COPIED, REPRODUCED OR DISCLOSED TO ANY CREE CONFIDENTIAL. THIS PLOT AND UNAUTHORIZED CONTAINED WITHIN ARE THE PROPRIETARY AND PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 6 0.4 0.4 3 4 2 REV 5.00 RECOMMENDED STENCIL PATTERN SHADED AREA IS OPEN 5.00 THIRD ANGLE PROJECTION 5.00 4 FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: B D. CRONIN DATE -- 0.57 DATE APPROVED -- 0.5 10/22/1 0.5 0.5 A OUTLINE DRAWING, 5050 XM -- SIZE FINAL PROTECTIVE FINISH -- 3 Fax (919) 313-5558 TITLE -- MATERIAL 1.6 0.57 DDS 0.5 Phone (919) 313-5300 -- DATE 4/15/1 2.8 2.8 4600 Silicon Drive Durham, N.C 27703 04/9/10 CHECK BY DC Added die ou Added die outline 3.8 3.8 3.02 DATE NEW RELEAS NEW RELEASE B DRAWN BY DESCRIPTION REVISONS DESCRIPTION A 3.02 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° REV A D D 2 3 SCALE C REV. DRAWING NO. 2610-00009 SHEET 16.000 2 B OF 1 /1 1 5.00 4.8 C C Top View Bottom View Side View 4.7 3.9 4.8 4.7 3.9 3.8 4.8 0.5 3.8 0.5 0.6 0.6 B B 0.5 0.4 4.8 0.5 4.8 4.7 0.5 2.782 0.5 0.4 A A 0.4 2.782 0.4 0.4 0.4 0.4 Recommended Solder RECOMMENDED PCB PCB SOLDER PAD RECOMMENDED PCB SOLDER PAD 4.7 0.4 UNLESS OTHERWISE SPECIFIED RECOMMENDED STENCIL PATTERN DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. SHADED AREA IS OPEN Pad Recommended Stencil Pattern TOLERANCE UNLESS SPECIFIED: UNLESS OTHERWISE SPECIFIED RECOMMENDED STENCIL PATTERN D. CRONIN 04/9/10 .XX ± .25 DIMENSIONS ARE IN .XXX ± .125 AND AFTER FINISH. SHADED AREA IS OPEN (Shaded AreaMILLIMETERS Is Open) THIRD ANGLE PROJECTION DRAWN BY DATE CHECK DATE X°-- ± .5 ° -TOLERANCE UNLESS SPECIFIED: THIRD ANGLE PROJECTION .XX ± .25 DATE METAL PARTS ONLY APPROVED FOR SHEET TITLE .XXX ± .125 .X-- ± 1.5 -X° ± .5 ° .XX ± .75 .XXX ± .25 FOR SHEET METAL PARTS ONLY MATERIAL X° ± .5 ° .X ± 1.5 SIZE 1.6 .XX ± .75 SURFACE FINISH: .XXX ± .25 FINAL PROTECTIVE FINISH 3 X° ± .5 ° 5 4 SURFACE FINISH: 1.6 6 5 4 3 Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. This is a preliminary, non-binding product specification provided for informational purposes only and is subject to change without notice. This product is unreleased and is provided “as is” without warranty. 12 CLD-DS33 Rev 0 D. CRONIN 04/9/10 DATE -- -DATE APPROVED -- -- MATERIAL 46 Du Ph Fa -OUTLINE DRAWING, -- 6 DATE DRAWN BY CHECK -- C SCALE FINAL PROTECTIVE FINISH DRAWING NO. 16.000 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp -- 2610-0000 2 SH