Cree® XLamp® XP-G LEDs Data Sheet The XLamp XP-G LED delivers unprecedented levels of light output and efficacy for a single die LED. The XLamp XP-G LED continues Cree’s history of innovation in LEDs for lighting applications with wide viewing angle, symmetrical package, unlimited floor life and electrically neutral thermal path. XLamp XP-G LEDs are the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. FEATURES • Available in white and outdoor white • ANSI-compatible chromaticity bins • Maximum drive current: 1500 mA • Low thermal resistance: 6°C/W • Wide viewing angle: 125° • Unlimited floor life at ≤ 30ºC/85% RH • Reflow solderable - JEDEC J-STD-020C • Electrically neutral thermal path • RoHS and REACH-compliant • UL-recognized component (E326295) ev 3 CLD-DS20 R Data Sheet: Table of Contents Flux Characteristics (TJ = 25°C).................................................................................................................. 2 Characteristics......................................................................................................................................... 2 Relative Spectral Power Distribution............................................................................................................ 3 Relative Flux vs. Junction Temperature (IF = 350 mA).................................................................................... 3 Electrical Characteristics (TJ = 25°C)........................................................................................................... 4 Thermal Design........................................................................................................................................ 4 Relative Flux vs. Current (TJ = 25°C).......................................................................................................... 5 Typical Spatial Distribution......................................................................................................................... 5 Reflow Soldering Characteristics................................................................................................................. 6 Notes...................................................................................................................................................... 7 Mechanical Dimensions (TA = 25°C)............................................................................................................ 8 Tape and Reel.......................................................................................................................................... 9 Packaging.............................................................................................................................................. 10 Subject to change without notice. www.cree.com/xlamp 1 Flux Characteristics (TJ = 25°C) The following table provides several base order codes for XLamp XP-G LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. Color Min. Cool White Outdoor White Neutral White Warm White Base Order Codes Min Luminous Flux @ 350 mA (lm) CCT Range 5,000 K 4,000 K 3,700 K 2,600 K Max. 8,300 K 5,300 K 5,000 K 3,700 K Order Code Group Flux (lm) R2 114 XPGWHT-L1-0000-00E51 R3 122 XPGWHT-L1-0000-00F51 R4 130 XPGWHT-L1-0000-00G51 R5 139 XPGWHT-L1-0000-00H51 R2 114 XPGWHT-01-0000-00EC2 R3 122 XPGWHT-01-0000-00FC2 R4 130 XPGWHT-01-0000-00GC2 Q5 107 XPGWHT-L1-0000-00DE4 R2 114 XPGWHT-L1-0000-00EE4 R3 122 XPGWHT-L1-0000-00FE4 Q3 93.9 XPGWHT-L1-0000-00BE7 Q4 100 XPGWHT-L1-0000-00CE7 Q5 107 XPGWHT-L1-0000-00DE7 Notes: • Cree maintains a tolerance of +/- 7% on flux and power measurements. • Typical CRI for Cool White and Neutral White (3,700 K - 10,000 K CCT) is 75. • Typical CRI for Outdoor White (4,000 K - 5,300 K CCT) is 70. • Typical CRI for Warm White (2,600 K - 3,700 K CCT) is 80. Characteristics Characteristics Unit Thermal resistance, junction to solder point °C/W 6 degrees 125 mV/°C -2.1 Viewing angle (FWHM) Temperature coefficient of voltage ESD classification (HBM per Mil-Std-883D) DC forward current Minimum Typical Maximum Class 2 mA 1500 Reverse voltage V 5 Forward voltage (@ 350 mA) V 3.0 Forward voltage (@ 700 mA) V 3.2 Forward voltage (@ 1000 mA) V 3.3 LED junction temperature °C 3.75 150 * The increase of maximum forward current to 1500 mA for XLamp XP-G Cool White is retroactive and applies to all XLamp XP-G Cool White LEDs produced by Cree. The increase is the result of more extensive qualification testing that was performed after the initial product launch. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 2 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 60 5000K - 8300K CCT 3700K - 5000K CCT 2600K - 3700K CCT 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) Relative Flux vs. Junction Temperature (IF = 350 mA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 JunctionTemperature Temperature (°C) Junction (ºC) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 3 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Electrical Characteristics (TJ = 25°C) 1500 1400 1300 Forward Current (mA) 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 Forward Voltage (V) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1600 Maximum Current (mA) 1400 1200 1000 800 Rj-a = = 10°C/W 10°C/W Rj-a = = 15°C/W 15°C/W Rj-a = = 20°C/W 20°C/W Rj-a = = 25°C/W 25°C/W 600 400 200 0 0 20 40 60 80 100 120 140 Ambient Temperature (ºC) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 4 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Relative Flux vs. Current (TJ = 25°C) Relative Luminous Flux (%) 350% 300% 250% 200% 150% 100% 50% 0% 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 Forward Current (mA) Typical Spatial Distribution Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (º) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 5 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Reflow Soldering Characteristics In testing, Cree has found XLamp XP-G LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3°C/second max. 3°C/second max. Preheat: Temperature Min (Tsmin) 100°C 150°C Preheat: Temperature Max (Tsmax) 150°C 200°C 60-120 seconds 60-180 seconds 183°C 217°C 60-150 seconds 60-150 seconds 215°C 260°C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 6 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Notes Lumen Maintenance Projections Cree currently recommends a maximum drive current of 1000 mA for XLamp XP-G white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating (≥ 94.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating (≥ 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp XP-G LEDs to have unlimited floor life in conditions ≤30ºC / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85ºC / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/ EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 7 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp All Measurements are .13mm unless otherwise indicated Mechanical Dimensions (TA = 25°C) All measurements are ±.13 mm unless otherwise indicated. B 6 5 4 3 2 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND 3.2 CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. REV DESC A Re 2.3 D 2 HIRD ANGLE PROJECTION 4600 Silicon Drive Durham, N.C 27703 DATE Phone (919) 313-5300 .73 B. Stanton Fax (919) 313-5558 APPROVED DATE 0.5 .50 XPG Top Level Customer Drawing MATERIAL SIZE C FINAL PROTECTIVE FINISH SCALE 1.6 3 1.3 0.5 2.30 0.58 A TITLE FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: DATE D. Seibel CHECK 3.30 2.00 3.453.45 8/28/09 DRAWN BY UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° REV. DRAWING NO. 2601-00005 B SHEET 25.000 2 OF 1 /1 1 3.453.45 C 2.6 1.30 Top View Side View 3.3 .50 Bottom View .60 1.30 2.3 .65 0.5 .50 1.20 .60 3.2 2.4 0.6 .50 .40 B 3.20 3.30 0.5 3.3 1.65 .40 .40 .40 .50 0.4 1.3 RECOMMENDED Recommended PCB Solder Pad SCALE 3.20 0.4 1.2 0.4 3.30 0.5 A 1.60 3.2 0.4 PCB SOLDER PAD 20.000 RECOMMENDED STENCIL PATTERN UNLESS OTHERWISE SPECIFIED (HATCHED AREA IS OPENING) DIMENSIONS ARE IN Recommended Stencil Pattern Shaded area is open SCALE 20.000 THIRD ANGLE PROJECTION MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 6 5 4 Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 8 CLD-DS20 Rev 3 DATE DRAWN BY D. Seibel 8/28/09 CHECK DATE APPROVED DATE MATERIAL FINAL PROTECTIVE FINISH 1.6 3 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Tape and Reel All dimensions in mm. 1.5±.1 4.0±.1 8.0±.1 1.75±.10 2.5±.1 Cathode Side +.3 12.0 .0 Anode Side (denoted by + and circle) User Feed Direction END START Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) Loaded Pockets (1,000 Lamps) Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction Cover Tape Pocket Tape 13mm 7" Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 9 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Dessicant Desiccant (inside bag) (inside bag) Humidity Indicator Humidity Indicator Card (inside bag)bag) (inside Packaging All dimensions in mm. Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label Bin with Cree Bin CREE Code & Barcode Label Code, Qty, Lot # Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO## Code, Qty, Lot Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO# Label with Cree Bin Code, Qty, Lot # Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 10 CLD-DS20 Rev 3 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp