TI LM63

LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
LM63 ±1°C/±3°C Accurate Remote Diode Digital Temperature Sensor with Integrated Fan
Control
Check for Samples: LM63
FEATURES
DESCRIPTION
•
The LM63 is a remote diode temperature sensor with
integrated fan control. The LM63 accurately
measures: (1) its own temperature and (2) the
temperature of a diode-connected transistor, such as
a 2N3904, or a thermal diode commonly found on
Computer Processors, Graphics Processor Units
(GPU) and other ASIC's. The LM63 remote
temperature sensor's accuracy is factory trimmed for
the series resistance and 1.0021 non-ideality of the
Intel 0.13 µm Pentium 4 and Mobile Pentium 4
Processor-M thermal diode. The LM63 has an offset
register to correct for errors caused by different nonideality factors of other thermal diodes.
1
23
•
•
•
•
•
•
•
•
•
•
•
•
•
Accurately Senses Diode-Connected 2N3904
Transistors or Thermal Diodes On Board Large
Processors or ASICs
Accurately Senses its Own Temperature
Factory Trimmed for Intel® Pentium® 4 and
Mobile Pentium 4 Processor-M Thermal Diodes
Integrated PWM Fan Speed Control Output
Acoustic Fan Noise Reduction With UserProgrammable 8-Step Lookup Table
Multi-Function, User-Selectable Pin for Either
ALERT Output, or Tachometer Input,
Functions
Tachometer Input for Measuring Fan RPM
Smart-Tach Modes for Measuring RPM of Fans
With Pulse-Width-Modulated Power as Shown
in Typical Application
Offset Register can Adjust for a Variety of
Thermal Diodes
10 Bit Plus Sign Remote Diode Temperature
Data Format, With 0.125°C Resolution
SMBus 2.0 Compatible Interface, Supports
TIMEOUT
LM86-Compatible Pinout
LM86-Compatible Register Set
8-Pin SOIC Package
The LM63 also features an integrated, pulse-widthmodulated (PWM), open-drain fan control output. Fan
speed is a combination of the remote temperature
reading, the lookup table and the register settings.
The 8-step Lookup Table enables the user to
program a non-linear fan speed vs. temperature
transfer function often used to quiet acoustic fan
noise.
CONNECTION DIAGRAM
VDD
D+
DPWM
1
8
7
2
3
4
LM63
6
5
SMBCLK
SMBDAT
ALERT / TACH
GND
APPLICATIONS
•
•
•
•
•
•
Computer Processor Thermal Management
(Laptop, Desktop, Workstations, Servers)
Graphics Processor Thermal Management
Electronic Test Equipment
Projectors
Office Equipment
Industrial Controls
Figure 1. 8-Pin SOIC (D Package)
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Intel, Pentium are registered trademarks of Intel Corporation.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2013, Texas Instruments Incorporated
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
KEY SPECIFICATIONS
•
Remote Diode Temp Accuracy (with quantization error)
•
Ambient Temp
Diode Temp
IPWML Max
Version
Max Error
30 to 50°C
60 to 100°C
5 mA
LM63C
±1.0°C
30 to 50°C
60 to 100°C
5 mA
LM63D
±3.0°C
0 to 85°C
25 to 125°C
8 mA
All
±3.0°C
Local Temp Accuracy (includes quantization error)
•
•
Ambient Temp
Max Error
25°C to 125°C
±3.0°C
Supply Voltage: 3.0 V to 3.6 V
Supply Current: 1.3 mA (typ)
PIN DESCRIPTIONS
2
PIN
NAME
INPUT/OUTPUT
FUNCTION AND CONNECTION
1
VDD
Power Supply Input
2
D+
Analog Input
Connect to the anode (positive side) of the remote diode. A 2.2 nF ceramic capacitor
must be connected between pins 2 and 3.
3
D−
Analog Input
Connect to the cathode (negative side) of the remote diode. A 2.2 nF ceramic capacitor
must be connected between pins 2 and 3.
4
PWM
Open-Drain
Digital Output
Open-Drain Digital Output. Connect to fan drive circuitry. The power-on default for this
pin is low (pin 4 pulled to ground).
5
GND
Ground
6
ALERT/TACH
Digital I/O
7
SMBDAT
Digital Input/
Open-Drain Output
8
SMBCLK
Digital Input
Connect to a low-noise +3.3 ± 0.3 VDC power supply, and bypass to GND with a
0.1 µF ceramic capacitor in parallel with a 100 pF ceramic capacitor. A bulk
capacitance of 10 µF needs to be in the vicinity of the LM63's VDD pin.
This is the analog and digital ground return.
Depending on how the LM63 is programmed, this pin is either an open-drain ALERT
output or a tachometer input for measuring fan speed. The power-on default for this pin
is the ALERT function.
This is the bi-directional SMBus data line.
Digital Input. This is the SMBus clock input.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
SIMPLIFIED BLOCK DIAGRAM
Internal Diode
LM63
D+
D-
Diode
Bias and
Control
'6 ADC
Tachometer
Detection
SMBDAT
SMBCLK
2 - Wire
Serial
Interface
Temp Reading,
Temp Limit,
Hysteresis, and
Temp Sensor
Filter Registers
Comparators
Tach
ALERT/Tach
ALERT
Status and Status
Mask Registers
PWM
PWM Fan Control
Registers
PWM Fan
Control
Figure 2.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
3
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
TYPICAL APPLICATION
+3.3 VDC from motherboard
0.1
10 PF
These two capacitors
are close to Pin 1
ALERT to system
shutdown circuitry
Fan voltage
+12 or +5 VDC
100 pF
LM63
1
Processor
2
VDD
SMBCLK
D+
SMBDAT
D-
ALERT / Tach
8
7
To SMBus
interface
control
circuitry
2.2 nF
3
4
PWM
GND
6
13k
Tach In
5
10k
Fan V+
Tach. input
from Fan
Fan V-
+3.3 VDC
Remote diodeconnected transistor
inside of an Intel®
Pentium® 4 Processor
1k
0.2W
DC brushless
fan module with
Tachometer
470
PWM Output
10
MMBT2222A
Figure 3.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
4
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
ABSOLUTE MAXIMUM RATINGS (1) (2)
−0.3 V to 6.0 V
Supply Voltage, VDD
−0.5 V to 6.0 V
Voltage on SMBDAT, SMBCLK, ALERT/Tach, PWM Pins
−0.3 V to (VDD + 0. 3 V)
Voltage on Other Pins
Input Current, D− Pin
±1 mA
Input Current at All Other Pins
(3)
5 mA
Package Input Current (3)
30 mA
Package Power Dissipation
See (4)
SMBDAT, ALERT, PWM pins
Output Sink Current
10 mA
−65°C to +150°C
Storage Temperature
Human Body Model
ESD Susceptibility (5)
SOIC-8 Package (6)
Soldering Information, Lead Temperature
(1)
(2)
(3)
(4)
(5)
(6)
2000 V
Machine Model
200 V
Vapor Phase (60 seconds)
215°C
Infrared (15 seconds)
220°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure performance limits. For ensured specifications and test conditions, see the Electrical
Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade
when the device is not operated under the listed test conditions.
All voltages are measured with respect to GND, unless otherwise noted.
When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > V+), the current at that pin should be limited to
5 mA. Parasitic components and/or ESD protection circuitry for the LM63's pins are shown in Figure 4 and Table 1. The nominal
breakdown voltage of D3 is 6.5 V. Care should be taken not to forward bias the parasitic diode, D1, present on pins D+ and D−. Doing
so by more than 50 mV may corrupt temperature measurements. An "X" means it exists in the circuit.
Thermal resistance junction-to-ambient when attached to a printed circuit board with 2 oz. foil is 168°C/W.
Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin. See
Figure 4 and Table 1 for the ESD Protection Input Structure.
See the URL http://www.ti.com/packaging for other recommendations and methods of soldering surface mount devices.
V+
D1
D3
D4
D6
I/O
D2
ESD
Clamp
SNP
R1
D5
D7
GND
Figure 4. ESD Protection Input Structure
Table 1. ESD Protection Input Structure
PIN NAME
PIN #
VDD
1
D1
D2
D+
2
X
X
X
X
D3
D4
D5
D6
R1
X
X
X
X
X
SNP
X
ESD CLAMP
X
X
X
D−
3
PWM
4
X
X
X
X
X
ALERT/Tach
6
X
X
X
X
SMBDAT
7
X
X
X
X
SMBCLK
8
X
X
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
5
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
OPERATING RATINGS (1) (2)
Specified Temperature Range (TMIN ≤ TA ≤ TMAX)
0°C ≤ TA ≤ +85°C
LM63CIM, LM63DIM
0°C ≤ TA ≤ +125°C
Remote Diode Temperature Range
Supply Voltage Range (VDD)
(1)
(2)
+3.0 V to +3.6 V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure performance limits. For ensured specifications and test conditions, see the Electrical
Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade
when the device is not operated under the listed test conditions.
All voltages are measured with respect to GND, unless otherwise noted.
DC ELECTRICAL CHARACTERISTICS
TEMPERATURE-TO-DIGITAL CONVERTER CHARACTERISTICS
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = +25°C.
PARAMETER
CONDITIONS
LIMITS (2)
UNITS
(LIMITS)
LM63C
±1
°C (max)
LM63D
±3
°C (max)
All
±3
°C (max)
±3
°C (max)
VERSION
Temperature Error Using the
Remote Thermal Diode of an Intel
Pentium 4 or Mobile Pentium 4
Processor-M with typical nonideality of 1.0021.
TA = +30 to +50°C
IPWML ≤ 5 mA
TD = +60 to +100°C
TD = Remote Diode
Junction Temperature
TA = +0 to +85°C
IPWML ≤ 8 mA
TD = +25 to +125°C
Temperature Error Using the Local
Diode
TA = +25 to +125°C (3) (4)
All
Remote Diode Resolution
All
Local Diode Resolution
All
Conversion Time, All Temperatures
TYPICAL (1)
Fastest Setting
D− Source Voltage
(VD+ − VD−) = +0.65 V; High Current
±1
11
Bits
0.125
°C
8
Bits
1
All
31.25
All
0.7
All
160
°C
34.4
V
315
Diode Source Current
Low Current
(1)
(2)
(3)
(4)
All
ms (max)
µA (max)
110
µA (min)
20
µA (max)
7
µA (min)
13
“Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
Limits are specified to AOQL (Average Outgoing Quality Level).
Local temperature accuracy does not include the effects of self-heating. The rise in temperature due to self-heating is the product of the
internal power dissipation of the LM63 and the thermal resistance. For the thermal resistance to be used in the self-heating calculation,
see the table footnote about Thermal resistance junction-to-ambient.
Thermal resistance junction-to-ambient when attached to a printed circuit board with 2 oz. foil is 168°C/W.
OPERATING ELECTRICAL CHARACTERISTICS
PARAMETER
ALERT
ALERT and PWM Output Saturation Voltage
TYPICAL (1)
CONDITIONS
IOUT
4 mA
IOUT
6 mA
(1)
(2)
(3)
6
(3)
UNITS
PWM
5 mA
0.4
0.55
Power-On-Reset Threshold Voltage
Supply Current
LIMITS (2)
SMBus Inactive, 16 Hz
Conversion Rate
1.1
STANDBY Mode
300
V (max)
2.4
V (max)
1.8
V (min)
2.0
mA (max)
µA
“Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
Limits are specified to AOQL (Average Outgoing Quality Level).
The supply current will not increase substantially with an SMBus transaction.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
AC ELECTRICAL CHARACTERISTICS
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TMIN to TMAX; all other limits TA= +25°C.
LIMITS (2)
UNITS
(LIMIT)
Fan Control Accuracy
±10
% (max)
Fan Full-Scale Count
65535
(max)
SYMBOL
PARAMETER
CONDITIONS
TYPICAL (1)
TACHOMETER ACCURACY
Fan Counter Clock Frequency
90
kHz
Fan Count Update Frequency
1.0
Hz
FAN PWM OUTPUT
Frequency Accuracy
(1)
(2)
±10
% (max)
“Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
Limits are specified to AOQL (Average Outgoing Quality Level).
DIGITAL ELECTRICAL CHARACTERISTICS
SYMBOL
(1)
(2)
PARAMETER
CONDITIONS
TYPICAL (1)
UNITS
(LIMIT)
LIMITS (2)
VIH
Logical High Input Voltage
2.1
V (min)
VIL
Logical Low Input Voltage
0.8
V (max)
IIH
Logical High Input Current
VIN = VDD
0.005
+10
µA (max)
IIL
Logical Low Input Current
VIN = GND
−0.005
−10
µA (max)
CIN
Digital Input Capacitance
20
pF
“Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
Limits are specified to AOQL (Average Outgoing Quality Level).
SMBus LOGICAL ELECTRICAL CHARACTERISTICS
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = +25°C.
SYMBOL
PARAMETER
CONDITIONS
TYPICAL (1)
LIMITS (2)
UNITS
(LIMIT)
SMBDAT OPEN-DRAIN OUTPUT
VOL
Logic Low Level Output Voltage
IOL = 4 mA
IOH
High Level Output Current
VOUT = VDD
0.03
0.4
V (max)
10
µA (max)
SMBDAT, SMBCLK INPUTS
VIH
Logical High Input Voltage
2.1
V (min)
VIL
Logical Low Input Voltage
0.8
V (max)
VHYST
(1)
(2)
Logic Input Hysteresis Voltage
320
mV
“Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
Limits are specified to AOQL (Average Outgoing Quality Level).
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
7
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
SMBus DIGITAL SWITCHING CHARACTERISTICS
Unless otherwise noted, these specifications apply for VDD = +3.0 VDC to +3.6 VDC, CL (load capacitance) on output lines =
80 pF. Boldface limits apply for TA = TJ; TMIN ≤ TA ≤ TMAX; all other limits TA = TJ = +25°C, unless otherwise noted. The
switching characteristics of the LM63 fully meet or exceed the published specifications of the SMBus version 2.0. The
following parameters are the timing relationships between SMBCLK and SMBDAT signals related to the LM63. They adhere
to, but are not necessarily the same as the SMBus bus specifications.
SYMBOL
PARAMETER
CONDITIONS
LIMITS (1)
UNITS
(LIMIT)
10
100
kHz (min)
kHz (max)
fSMB
SMBus Clock Frequency
tLOW
SMBus Clock Low Time
From VIN(0) max to VIN(0) max
4.7
µs (min)
tHIGH
SMBus Clock High Time
From VIN(1) min to VIN(1) min
4.0
50
µs (min)
µs (max)
tR
SMBus Rise Time
See
(2)
1
µs (max)
tF
SMBus Fall Time
See
(3)
0.3
µs (max)
tOF
Output Fall Time
CL = 400 pF, IO = 3 mA
250
ns (max)
tTIMEOUT
SMBData and SMBCLK Time Low for Reset of
Serial Interface. See (4).
25
35
ms (min)
ms (max)
tSU:DAT
Data In Setup Time to SMBCLK High
250
ns (min)
tHD:DAT
Data Out Hold Time after SMBCLK Low
300
930
ns (min)
ns (max)
tHD:STA
Hold Time after (Repeated) Start Condition. After
this period the first clock is generated.
4.0
µs (min)
tSU:STO
Stop Condition SMBCLK High to SMBDAT Low
(Stop Condition Setup)
100
ns (min)
tSU:STA
SMBus Repeated Start-Condition Setup Time,
SMBCLK High to SMBDAT Low
4.7
µs (min)
tBUF
SMBus Free Time between Stop and Start
Conditions
4.7
µs (min)
(1)
(2)
(3)
(4)
Limits are specified to AOQL (Average Outgoing Quality Level).
The output rise time is measured from (VIL max - 0.15 V) to (VIH min + 0.15 V).
The output fall time is measured from (VIH min + 0.15 V) to (VIL min - 0.15 V).
Holding the SMBData and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will reset the LM63’s SMBus state machine,
therefore setting SMBDAT and SMBCLK pins to a high-impedance state.
tLOW
tR
tF
VIH
SMBCLK
VIL
tBUF
tHD;STA
tHIGH
tHD;DAT
tSU;STA
tSU;DAT
tSU;STO
VIH
SMBDAT
VIL
P
S
P
Figure 5. SMBus Timing Diagram for SMBCLK and SMBDAT Signals
8
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
FUNCTIONAL DESCRIPTION
The LM63 Remote Diode Temperature Sensor with Integrated Fan Control incorporates a ΔVBE-based
temperature sensor using a Local or Remote diode and a 10-bit plus sign ΔΣ ADC (Delta-Sigma Analog-to-Digital
Converter). The pulse-width modulated (PWM) open-drain output, with a pullup resistor, can drive a switching
transistor to modulate fan speed. When the ALERT/Tach is programmed to the Tach mode the LM63 can
measure the fan speed on the pulses from the fan’s tachometer output. The LM63 includes a smart-tach
measurement mode to accommodate the corrupted tachometer pulses when using switching transistor drive.
When the ALERT/Tach pin is programmed to the ALERT mode the ALERT open-drain output will be pulled low
when the measured temperature exceeds certain programmed limits when enabled. Details are contained in the
sections to follow.
The LM63's two-wire interface is compatible with the SMBus Specification 2.0. For more information the reader is
directed to www.smbus.org.
In the LM63 digital comparators are used to compare the measured Local Temperature (LT) to the Local High
Setpoint user-programmable temperature limit register. The measured Remote Temperature (RT) is digitally
compared to the Remote High Setpoint (RHS), the Remote Low Setpoint (RLS), and the Remote T_CRIT
Setpoint (RCS) user-programmable temperature limits. An ALERT output will occur when the measured
temperature is: (1) higher than either the High Setpoint or the T_CRIT Setpoint, or (2) lower than the Low
Setpoint. The ALERT Mask register allows the user to prevent the generation of these ALERT outputs.
The temperature hysteresis is set by the value placed in the Hysteresis Register (TH).
The LM63 may be placed in a low-power Standby mode by setting the Standby bit found in the Configuration
Register. In the Standby mode continuous conversions are stopped. In Standby mode the user may choose to
allow the PWM output signal to continue, or not, by programming the PWM Disable in Standby bit in the
Configuration Register.
The Local Temperature reading and setpoint data registers are 8-bits wide. The format of the 11-bit remote
temperature data is a 16-bit left justified word. Two 8-bit registers, high and low bytes, are provided for each
setpoint as well as the temperature reading. Two Remote Temperature Offset (RTO) Registers: High Byte and
Low Byte (RTOHB and RTOLB) may be used to correct the temperature readings by adding or subtracting a
fixed value based on a different non-ideality factor of the thermal diode if different from the 0.13 micron Intel
Pentium 4 or Mobile Pentium 4 Processor-M processor’s thermal diode. See the DIODE NON-IDEALITY section.
CONVERSION SEQUENCE
The LM63 takes approximately 31.25 ms to convert the Local Temperature (LT), Remote Temperature (RT), and
to update all of its registers. The Conversion Rate may be modified using the Conversion Rate Register. When
the conversion rate is modified a delay is inserted between conversions, the actual conversion time remains at
31.25 ms. Different Conversion Rates will cause the LM63 to draw different amounts of supply current as shown
in Figure 6.
2600
SUPPLY CURRENT (PA
2300
2000
1700
1400
1100
800
500
200
0.01
0.1
1.0
10
100
CONVERSION RATE (Hz)
Figure 6. Supply Current vs Conversion Rate
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
9
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
THE ALERT/TACH PIN AS ALERT OUTPUT
The ALERT/Tach pin is a multi-use pin. In this section, we will address the ALERT active-low open-drain output
function. When the ALERT/Tach Select bit is written as a zero in the Configuration Register the ALERT output is
selected. Also, when the ALERT Mask bit in the Configuration register is written as zero the ALERT interrupts
are enabled.
The LM63's ALERT pin is versatile and can produce three different methods of use to best serve the system
designer: (1) as a temperature comparator (2) as a temperature-based interrupt flag, and (3) as part of an
SMBus ALERT System. The three methods of use are further described in the following sections: ALERT
OUTPUT AS A TEMPERATURE COMPARATOR, ALERT OUTPUT AS AN INTERRUPT, and ALERT OUTPUT
AS AN SMBus ALERT. The ALERT and interrupt methods are different only in how the user interacts with the
LM63.
The remote temperature (RT) reading is associated with a T_CRIT Setpoint Register, and both local and remote
temperature (LT and RT) readings are associated with a HIGH setpoint register (LHS and RHS). The RT is also
associated with a LOW setpoint register (RLS). At the end of every temperature reading a digital comparison
determines whether that reading is above its HIGH or T_CRIT setpoint or below its LOW setpoint. If so, the
corresponding bit in the ALERT Status Register is set. If the ALERT mask bit is low, any bit set in the ALERT
Status Register, with the exception of Busy or Open, will cause the ALERT output to be pulled low. Any
temperature conversion that is out of the limits defined in the temperature setpoint registers will trigger an
ALERT. Additionally, the ALERT Mask Bit must be cleared to trigger an ALERT in all modes.
The three different ALERT modes will be discussed in the following sections: ALERT OUTPUT AS A
TEMPERATURE COMPARATOR, ALERT OUTPUT AS AN INTERRUPT, and ALERT OUTPUT AS AN SMBus
ALERT.
ALERT OUTPUT AS A TEMPERATURE COMPARATOR
When the LM63 is used in a system in which does not require temperature-based interrupts, the ALERT output
could be used as a temperature comparator. In this mode, once the condition that triggered the ALERT to go low
is no longer present, the ALERT is negated (Figure 7). For example, if the ALERT output was activated by the
comparison of LT > LHS, when this condition is no longer true, the ALERT will return HIGH. This mode allows
operation without software intervention, once all registers are configured during set-up. In order for the ALERT to
be used as a temperature comparator, the Comparator Mode bit in the Remote Diode Temperature Filter and
Comparator Mode Register must be asserted. This is not the power-on default state.
Temperature
Remote High Limit
RDTS Measurement
LM63 ALERT Pin
Status Register: RTDS High
Time
Figure 7. ALERT Output as Temperature Comparator Response Diagram
10
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
ALERT OUTPUT AS AN INTERRUPT
The LM63's ALERT output can be implemented as a simple interrupt signal when it is used to trigger an interrupt
service routine. In such systems it is desirable for the interrupt flag to repeatedly trigger during or before the
interrupt service routine has been completed. Under this method of operation, during the read of the ALERT
Status Register the LM63 will set the ALERT Mask bit in the Configuration Register if any bit in the ALERT
Status Register is set, with the exception of Busy and Open. This prevents further ALERT triggering until the
master has reset the ALERT Mask bit, at the end of the interrupt service routine. The ALERT Status Register bits
are cleared only upon a read command from the master (see Figure 8 ) and will be re-asserted at the end of the
next conversion if the triggering condition(s) persist(s). In order for the ALERT to be used as a dedicated
interrupt signal, the Comparator Mode bit in the Remote Diode Temperature Filter and Comparator Mode
Register must be set low. This is the power-on default state. The following sequence describes the response of a
system that uses the ALERT output pin as an interrupt flag:
1. Master senses ALERT low.
2. Master reads the LM63 ALERT Status Register to determine what caused the ALERT.
3. LM63 clears ALERT Status Register, resets the ALERT HIGH and sets the ALERT Mask bit in the
Configuration Register.
4. Master attends to conditions that caused the ALERT to be triggered. The fan is started, setpoint limits are
adjusted, etc.
5. Master resets the ALERT Mask bit in the Configuration Register.
Temperature
Remote High Limit
LM63
ALERT pin
RDTS Measurement
ALERT mask set in
response to reading of
status register by master
End of Temperature
conversion
Status Register: RTDS High
Time
Figure 8. ALERT Output as an Interrupt Temperature Response Diagram
ALERT OUTPUT AS AN SMBus ALERT
An SMBus alert line is created when the ALERT output is connected to: (1) one or more ALERT outputs of other
SMBus compatible devices, and (2) to a master. Under this implementation, the LM63's ALERT should be
operated using the ARA (Alert Response Address) protocol. The SMBus 2.0 ARA protocol, defined in the SMBus
specification 2.0, is a procedure designed to assist the master in determining which part generated an interrupt
and to service that interrupt.
The SMBus alert line is connected to the open-drain ports of all devices on the bus, thereby AND'ing them
together. The ARA method allows the SMBus master, with one command, to identify which part is pulling the
SMBus alert line LOW. It also prevents the part from pulling the line LOW again for the same triggering condition.
When an ARA command is received by all devices on the bus, the devices pulling the SMBus alert line LOW:
(1) send their address to the master and (2) release the SMBus alert line after acknowledgement of their
address.
The SMBus Specifications 1.1 and 2.0 state that in response to and ARA (Alert Response Address) “after
acknowledging the slave address the device must disengage its ALERT pulldown”. Furthermore, “if the host still
sees ALERT low when the message transfer is complete, it knows to read the ARA again.” This SMBus
“disengaging ALERT requirement prevents locking up the SMBus alert line. Competitive parts may address the
“disengaging of ALERT” differently than the LM63 or not at all. SMBus systems that implement the ARA protocol
as suggested for the LM63 will be fully compatible with all competitive parts.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
11
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
The LM63 fulfills “disengaging of ALERT” by setting the ALERT Mask Bit in the Configuration Register after
sending out its address in response to an ARA and releasing the ALERT output pin. Once the ALERT Mask bit is
activated, the ALERT output pin will be disabled until enabled by software. In order to enable the ALERT the
master must read the ALERT Status Register, during the interrupt service routine and then reset the ALERT
Mask bit in the Configuration Register to 0 at the end of the interrupt service routine.
The following sequence describes the ARA response protocol.
1. Master senses SMBus alert line low
2. Master sends a START followed by the Alert Response Address (ARA) with a Read Command.
3. Alerting Device(s) send ACK.
4. Alerting Device(s) send their address. While transmitting their address, alerting devices sense whether their
address has been transmitted correctly. (The LM63 will reset its ALERT output and set the ALERT Mask bit
once its complete address has been transmitted successfully.)
5. Master/slave NoACK
6. Master sends STOP
7. Master attends to conditions that caused the ALERT to be triggered. The ALERT Status Register is read and
fan started, setpoints adjusted, etc.
8. Master resets the ALERT Mask bit in the Configuration Register.
The ARA, 000 1100, is a general call address. No device should ever be assigned to this address.
The ALERT Configuration bit in the Remote Diode Temperature Filter and Comparator Mode Register must be
set low in order for the LM63 to respond to the ARA command.
The ALERT output can be disabled by setting the ALERT Mask bit in the Configuration Register. The power-on
default is to have the ALERT Mask bit and the ALERT Configuration bit low.
Temperature
Remote High Limit
RDTS Measurement
LM63
ALERT Pin
ALERT mask set in
response to ARA
from master
Status Register: Remote High
Time
Figure 9. ALERT Output as an SMBus ALERT Temperature Response Diagram
SMBus INTERFACE
Since the LM63 operates as a slave on the SMBus the SMBCLK line is an input and the SMBDAT line is bidirectional. The LM63 never drives the SMBCLK line and it does not support clock stretching. According to
SMBus specifications, the LM63 has a 7-bit slave address. All bits, A6 through A0, are internally programmed
and cannot be changed by software or hardware.
The complete slave address is:
12
A6
A5
A4
A3
A2
A1
A0
1
0
0
1
1
0
0
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
POWER-ON RESET (POR) DEFAULT STATES
For information on the POR default states, see REGISTER MAP IN FUNCTIONAL ORDER.
TEMPERATURE DATA FORMAT
Temperature data can only be read from the Local and Remote Temperature registers. The High, Low and
T_CRIT setpoint registers are Read/Write.
Remote temperature data is represented by an 11-bit, two's complement word with a Least Significant Bit (LSB)
equal to 0.125°C. The data format is a left justified 16-bit word available in two 8-bit registers:
TEMPERATURE
DIGITAL OUTPUT
BINARY
HEX
+125°C
0111 1101 0000 0000
7D00
+25°C
0001 1001 0000 0000
1900
+1°C
0000 0001 0000 0000
0100
+0.125°C
0000 0000 0010 0000
0020
0°C
0000 0000 0000 0000
0000
−0.125°C
1111 1111 1110 0000
FFE0
−1°C
1111 1111 0000 0000
FF00
−25°C
1110 0111 0000 0000
E700
−55°C
1100 1001 0000 0000
C900
Local Temperature data is represented by an 8-bit, two's complement byte with an LSB equal to 1°C:
TEMPERATURE
DIGITAL OUTPUT
BINARY
HEX
+125°C
0111 1101
7D
+25°C
0001 1001
19
+1°C
0000 0001
01
0°C
0000 0000
00
−1°C
1111 1111
FF
−25°C
1110 0111
E7
−55°C
1100 1001
C9
OPEN-DRAIN OUTPUTS
The SMBDAT, ALERT, and PWM outputs are open-drain outputs and do not have internal pullups. A “High” level
will not be observed on these pins until pullup current is provided by an internal source, typically through a pullup
resistor. Choice of resistor value depends on several factors but, in general, the value should be as high as
possible consistent with reliable operation. This will lower the power dissipation of the LM63 and avoid
temperature errors caused by self-heating of the device. The maximum value of the pullup resistor to provide the
2.1 V high level is 88.7 kΩ.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
13
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
DIODE FAULT DETECTION
The LM63 can detect fault conditions caused by the remote diode. If the D+ pin is detected to be shorted to VDD,
or open: (1) the Remote Temperature High Byte (RTHB) register is loaded with 127°C, (2) the Remote
Temperature Low Byte (RTLB) register is loaded with 0, and (3) the OPEN bit (D2) in the status register is set.
Therefore, if the Remote T_CRIT setpoint register (RCS): (1) is set to a value less than +127°C and (2) the
ALERT Mask is disabled, then the ALERT output pin will be pulled low. If the Remote High Setpoint High Byte
(RHSHB) is set to a value less than +127°C and (2) the ALERT Mask is disabled, then the ALERT will be pulled
low. The OPEN bit by itself will not trigger an ALERT.
If the D+ pin is shorted to either ground or D−, then the Remote Temperature High Byte (RTHB) register is
loaded with −128°C (1000 0000) and the OPEN bit in the ALERT Status Register will not be set. A temperature
reading of −128°C indicates that D+ is shorted to either ground or D-. If the value in the Remote Low Setpoint
High Byte (RLSHB) Register is more than −128°C and the ALERT Mask is Disabled, ALERT will be pulled low.
COMMUNICATING WITH THE LM63
Each data register in the LM63 falls into one of four types of user accessibility:
1. Read Only
2. Write Only
3. Read/Write same address
4. Read/Write different address
A Write to the LM63 is comprised of an address byte and a command byte. A write to any register requires one
data byte.
Reading the LM63 Registers can take place after the requisite register setup sequence takes place. See
REQUIRED INITIAL FAN CONTROL REGISTER SEQUENCE.
The data byte has the Most Significant Bit (MSB) first. At the end of a read, the LM63 can accept either
Acknowledge or No-Acknowledge from the Master. Note that the No-Acknowledge is typically used as a signal
for the slave indicating that the Master has read its last byte.
DIGITAL FILTER
The LM63 incorporates a user-configured digital filter to suppress erroneous Remote Temperature readings due
to noise. The filter is accessed in the Remote Diode Temperature Filter and Comparator Mode Register. The
filter can be set according to Table 2.
Level 2 is maximum filtering.
Table 2. Digital Filter Selection Table
14
D2
D1
FILTER
0
0
No Filter
0
1
Level 1
1
0
Level 1
1
1
Level 2
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
50
No Filter
TEMPERATURE (°C)
45
40
Filter Level 1
35
Filter Level 2
30
25
0
5
10
15
20
25
NUMBER OF SAMPLES
Figure 10. Step Response of the Digital Filter
50
TEMPERATURE (°C)
45
No Filter
40
Filter Level 1
35
Filter Level 2
30
25
0
5
10
15
20
25
NUMBER OF SAMPLES
Figure 11. Impulse Response of the Digital Filter
45
LM63
with
Filter Off
43
TEMPERATURE (oC)
41
39
37
35
LM63
with
Filter On
33
31
29
27
25
0
50
100
150
200
SAMPLE NUMBER
Figure 12. Digital Filter Response in an Intel Pentium 4 processor System. The Filter on and off curves
were purposely offset to better show noise performance.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
15
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
FAULT QUEUE
TEMPERATURE
The LM63 incorporates a Fault Queue to suppress erroneous ALERT triggering. The Fault Queue prevents false
triggering by requiring three consecutive out-of-limit HIGH, LOW, or T_CRIT temperature readings. See
Figure 13. The Fault Queue defaults to OFF upon power-up and may be activated by setting the RDTS Fault
Queue bit in the Configuration Register to a 1.
RDTS Measurement
Status Register: RTDS High
n
n+1
n+2
n+3
n+4
n+5
SAMPLE NUMBER
Figure 13. Fault Queue Temperature Response Diagram
ONE-SHOT REGISTER
The One-Shot Register is used to initiate a single conversion and comparison cycle when the device is in
standby mode, after which the data returns to standby. This is not a data register. A write operation causes the
one-shot conversion. The data written to this address is irrelevant and is not stored. A zero will always be read
from this register.
SERIAL INTERFACE RESET
In the event that the SMBus Master is reset while the LM63 is transmitting on the SMBDAT line, the LM63 must
be returned to a known state in the communication protocol. This may be done in one of two ways:
1. When SMBDAT is Low, the LM63 SMBus state machine resets to the SMBus idle state if either SMBData or
SMBCLK are held Low for more than 35 ms (tTIMEOUT). All devices are to timeout when either the SMBCLK or
SMBDAT lines are held Low for 25 ms – 35 ms. Therefore, to insure a timeout of all devices on the bus,
either the SMBCLK or the SMBData line must be held Low for at least 35 ms.
2. With both SMBDAT and SMBCLK High, the master can initiate an SMBus start condition with a High to Low
transition on the SMBDAT line. The LM63 will respond properly to an SMBus start condition at any point
during the communication. After the start the LM63 will expect an SMBus Address address byte.
16
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
LM63 REGISTERS
This section includes the following subsections: REGISTER MAP IN HEXADECIMAL ORDER, which shows a
summary of all registers and their bit assignments; REGISTER MAP IN FUNCTIONAL ORDER; and REGISTER
DESCRIPTIONS IN FUNCTIONAL ORDER, which provides a detailed explanation of each register. Do not
address the unused or manufacturer’s test registers.
REGISTER MAP IN HEXADECIMAL ORDER
Table 3 is a Register Map grouped in hexadecimal address order. Some address locations have been left blank
to maintain compatibility with LM86. Addresses in parenthesis are mirrors of “Same As” address for backwards
compatibility with some older software. Reading or writing either address will access the same 8-bit register.
Table 3. Register Map Grouped in Hexadecimal Address Order
REGISTER
0x[HEX]
REGISTER
NAME
00
DATA BITS
D7
D6
D5
D4
D3
D2
D1
D0
Local
Temperature
LT7
LT6
LT5
LT4
LT3
LT2
LT1
LT0
01
Rmt Temp MSB
RTHB±
RTHB14
RTHB13
RTHB12
RTHB11
RTHB10
RTHB9
RTHB8
02
ALERT Status
BUSY
LHIGH
0
RHIGH
RLOW
RDFA
RCRIT
TACH
03
Configuration
ALTMSK
STBY
PWMDIS
0
0
ALT/TCH
TCRITOV
FLTQUE
04
Conversion
Rate
0
0
0
0
CONV3
CONV2
CONV1
CONV0
05
Local High
Setpoint
LHS7
LHS6
LHS5
LHS4
LHS3
LHS2
LHS1
LHS0
06
[Reserved]
07
Rmt High
Setpoint MSB
RHSHB15
RHSHB14
RHHBS13
RHSHB12
RHSHB11
RHSHB10
RHSHB9
RHSHB8
08
Rmt Low
Setpoint MSB
RLSHB15
RLSHB14
RLSHB13
RLSHB12
RLHBS11
RLSHB10
RLSHB9
RLSHB8
(09)
Same as 03
(0A)
Same as 04
(0B)
Same as 05
0C
[Reserved]
(0D)
Same as 07
(0E)
Same as 08
Not Used
Not Used
0F
One Shot
10
Rmt Temp LSB
RTLB7
RTLB6
RTLB5
0
0
0
0
0
11
Rmt Temp
Offset MSB
RTOHB15
RTOHB14
RTOHB13
RTOHB12
RTOHB11
RTOHB10
RTOHB9
RTOHB8
12
Rmt Temp
Offset LSB
RTOLB7
RTOLB6
RTOLB5
0
0
0
0
0
13
Rmt High
Setpoint LSB
RHSLB7
RHSLB6
RHSLB5
0
0
0
0
0
14
Rmt Low
Setpoint LSB
RLSLB7
RLSLB6
RLSLB5
0
0
0
0
0
1
ALTMSK6
1
ALTMSK4
ALTMSK3
1
ALTMSK1
ALTMSK0
RCS3
RCS2
RCS1
RCS0
RTH3
RTH2
RTH1
RTH0
15
[Reserved]
16
ALERT Mask
17
[Reserved]
Write Only. Write command triggers one temperature conversion cycle.
Not Used
Not Used
18
[Reserved]
19
Rmt TCRIT
Setpoint
Not Used
1A–1F
[Reserved]
20
[Reserved]
21
Rmt TCRIT
Hysteresis
22–2F
[Reserved]
Not Used
30–3F
[Reserved]
Not Used
40–45
[Reserved]
46
Tach Count LSB
TCLB5
TCLB4
TCLB3
TCLB2
TCLB1
TCLB0
TEDGE1
TEDGE0
47
Tach Count
MSB
TCHB13
TCHB12
TCHB11
TCHB10
TCHB9
TCHB8
TCHB7
TCHB6
48
Tach Limit LSB
TLLB7
TLLB6
TLLB5
TLLB4
TLLB3
TLLB2
Not Used
Not Used
RCS7
RCS6
RCS5
RCS4
Not Used
Not Used
RTH7
RTH6
RTH5
RTH4
Not Used
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
17
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 3. Register Map Grouped in Hexadecimal Address Order (continued)
18
DATA BITS
REGISTER
0x[HEX]
REGISTER
NAME
D7
D6
D5
D4
D3
D2
D1
D0
49
Tach Limit MSB
TLHB15
TLHB14
TLHB13
TLHB12
TLHB11
TLHB10
TLHB9
TLHB8
4A
PWM and RPM
0
0
PWPGM
PWOUT±
PWCKSL
0
TACH1
TACH0
4B
Fan Spin-Up
Config
0
0
SPINUP
SPNDTY1
SPNDTY0
SPNUPT2
SPNUPT1
SPNUPT0
4C
PWM Value
0
0
PWVAL5
PWVAL4
PWVAL3
PWVAL2
PWVAL1
PWVAL0
4D
PWM
Frequency
0
0
0
PWMF4
PWMF3
PWMF2
PWMF1
PWMF0
0
0
0
LOOKH4
LOOKH3
LOOKH2
LOOKH1
LOOKH0
4E
[Reserved]
4F
Lookup Table
Hystersis
50–5F
Lookup Table
60–BE
[Reserved]
BF
Rmt Diode
Temp Filter
Not Used
Lookup Table of up to 8 PWM and Temp Pairs in 8-bit Registers
Not Used
0
0
0
0
0
RDTF1
RDTF0
ALTCOMP
C0–FD
[Reserved]
FE
Manufacturer’s
ID
0
0
0
0
Not Used
0
0
0
1
FF
Stepping/Die
Rev. ID
0
1
0
0
0
0
0
1
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
REGISTER MAP IN FUNCTIONAL ORDER
Table 4 is a Register Map grouped in Functional Order. Some address locations have been left blank to maintain
compatibility with LM86. Addresses in parenthesis are mirrors of named address. Reading or writing either
address will access the same 8-bit register. The Fan Control and Configuration Registers are listed first, as there
is a required order to setup these registers first and then setup the others (see REQUIRED INITIAL FAN
CONTROL REGISTER SEQUENCE). The detailed explanations of each register will follow the order shown in
Table 4.
Note: POR = Power-On-Reset.
Table 4. Register Map Grouped in Functional Order
REGISTER
[HEX]
REGISTER NAME
READ/WRITE
POR DEFAULT
[HEX]
FAN CONTROL REGISTERS
4A
PWM and RPM
R/W
20
4B
Fan Spin-Up Configuration
R/W
3F
4D
PWM Frequency
4C
50–5F
4F
R/W
17
Read Only
(R/W if Override Bit is Set)
00
Lookup Table
R/W
See Table
Lookup Table Hysteresis
R/W
04
R/W
00
PWM Value
CONFIGURATION REGISTER
03 (09)
Configuration
TACHOMETER COUNT AND LIMIT REGISTERS
46
Tach Count LSB
Read Only
N/A
47
Tach Count MSB
Read Only
N/A
48
Tach Limit LSB
R/W
FF
49
Tach Limit MSB
R/W
FF
LOCAL TEMPERATURE AND LOCAL SETPOINT REGISTERS
00
Local Temperature
Read Only
N/A
05 (0B)
Local High Setpoint
R/W
46 (70°)
REMOTE DIODE TEMPERATURE AND SETPOINT REGISTERS
01
Remote Temperature MSB
Read Only
N/A
10
Remote Temperature LSB
Read Only
N/A
11
Remote Temperature Offset MSB
R/W
00
12
Remote Temperature Offset LSB
R/W
00
07 (0D)
Remote High Setpoint MSB
R/W
46 (70°C)
13
Remote High Setpoint LSB
R/W
00
08 (0E)
Remote Low Setpoint MSB
R/W
00 (0°C)
14
Remote Low Setpoint LSB
R/W
00
19
Remote TCRIT Setpoint
R/W
55 (85°C)
21
Remote TCRIT Hys
R/W
0A (10°C)
BF
Remote Diode Temperature Filter
R/W
00
CONVERSION AND ONE-SHOT REGISTERS
04 (0A)
0F
Conversion Rate
One-Shot
R/W
08
Write Only
N/A
ALERT STATUS AND MASK REGISTERS
02
ALERT Status
Read Only
N/A
16
ALERT Mask
R/W
A4
Read Only
41
ID AND TEST REGISTERS
FF
Stepping/Die Rev. ID
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
19
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 4. Register Map Grouped in Functional Order (continued)
REGISTER
[HEX]
REGISTER NAME
READ/WRITE
POR DEFAULT
[HEX]
[RESERVED] REGISTERS—NOT USED
20
06
Not Used
N/A
N/A
0C
Not Used
N/A
N/A
15
Not Used
N/A
N/A
17
Not Used
N/A
N/A
18
Not Used
N/A
N/A
1A–1F
Not Used
N/A
N/A
20
Not Used
N/A
N/A
22–2F
Not Used
N/A
N/A
30–3F
Not Used
N/A
N/A
40–45
Not Used
N/A
N/A
4E
Not Used
N/A
N/A
60–BE
Not Used
N/A
N/A
C0–FD
Not Used
N/A
N/A
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
REGISTER DESCRIPTIONS IN FUNCTIONAL ORDER
The REGISTER DESCRIPTIONS IN FUNCTIONAL ORDER section shows a Register Map grouped in functional
order. Some address locations have been left blank to maintain compatibility with LM86. Addresses in
parenthesis are mirrors of named address for backwards compatibility with some older software. Reading or
writing either address will access the same 8-bit register.
Table 5. Fan Control Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
4AHEX FAN PWM AND TACHOMETER CONFIGURATION REGISTER
7:6
4A
R/W
00
These bits are unused and always set to 0.
5
1
0: the PWM Value (register 4C) and the Lookup Table (50–5F) are readonly. The PWM value (0 to 100%) is determined by the current remote
diode temperature and the Lookup Table, and can be read from the
PWM value register.
1: the PWM value (register 4C) and the Lookup Table (Register 50–5F)
are read/write enabled. Writing the PWM Value register will set the PWM
output. This is also the state during which the Lookup Table can be
written.
4
0
PWM
Output
Polarity
3
0
PWM Clock
Select
if 0, the master PWM clock is 360 kHz
if 1, the master PWM clock is 1.4 kHz.
2
0
[Reserved]
Always write 0 to this bit.
Tachometer
Mode
00: Traditional tach input monitor, false readings when under minimum
detectable RPM.
01: Traditional tach input monitor, FFFF reading when under minimum
detectable RPM.
10: Most accurate readings, FFFF reading when under minimum
detectable RPM. Smart-tach mode enabled. Use with direct PWM drive
of fan power.
11: Least effort on programmed PWM of fan, FFFF reading when under
minimum detectable RPM. Smart-tach mode enabled. Use with direct
PWM drive of fan power.
Note: If the PWM Clock is 360 kHz, mode 00 is used regardless of the
setting of these two bits.
1:0
00
PWM
Program
0: the PWM output pin will be 0 V for fan OFF and open for fan ON.
1: the PWM output pin will be open for fan OFF and 0 V for fan ON.
4BHEX FAN PWM AND TACHOMETER CONFIGURATION REGISTER
7:6
5
4B
0
These bits are unused and always set to 0
1
If 0, the fan spin-up uses the duty cycle and spin-up time, bits 0–4.
If 1, the LM63 sets the PWM output to 100% until the spin-up times out
(per bits 0–2) or the minimum desired RPM has been reached (per the
Tachometer Setpoint setting) using the tachometer input, whichever
happens first. This bit overrides the PWM Spin-Up Duty Cycle register
(bits 4:3)—PWM output is always 100%. Register x03, bit 2 = 1 for
Tachometer mode.
If PWM Spin-Up Time (bits 2:0) = 000, the Spin-Up cycle is bypassed,
regardless of the state of this bit.
R/W
4:3
2:0
11
111
Fast
Tachometer
Spin-Up
PWM
Spin-Up
Duty Cycle
PWM
Spin-Up
Time
00: Spin-Up cycle bypassed (no Spin-Up), unless Fast Tachometer
Terminated Spin-Up (bit 5) is set.
01: 50%
10: 75%–81% Depends on PWM Frequency. See the APPLICATION
NOTES section at the end of this datasheet.
11: 100%
000:
001:
010:
011:
100:
101:
110:
111:
Spin-Up cycle bypassed (No Spin-Up)
0.05 seconds
0.1 s
0.2 s
0.4 s
0.8 s
1.6 s
3.2 s
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
21
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 5. Fan Control Registers (continued)
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
4DHEX FAN PWM FREQUENCY REGISTER
7:5
4D
R/W
4:0
000
10111
These bits are unused and always set to 0
PWM
Frequency
The PWM Frequency = PWM_Clock / 2n, where PWM_Clock = 360 kHz
or 1.4 kHz (per the PWM Clock Select bit in Register 4A), and n = value
of the register.
Note: n = 0 is mapped to n = 1. See the APPLICATION NOTES section
at the end of this datasheet.
4CHEX PWM VALUE REGISTER
7:6
4C
22
Read
(Write only
if reg 4A
bit 5 = 1.)
5:0
00
000000
These bits are unused and always set to 0
PWM
Value
If PWM Program (register 4A, bit 5) = 0 this register is read only and
reflects the LM63’s current PWM value from the Lookup Table.
If PWM Program (register 4A, bit 5) = 1, this register is read/write and the
desired PWM value is written directly to this register, instead of from the
Lookup Table, for direct fan speed control.
This register will read 0 during the Spin-Up cycle.
See the APPLICATION NOTES section at the end of this datasheet for
more information regarding the PWM Value and Duty Cycle in %.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
Table 5. Fan Control Registers (continued)
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
50HEX to 5FHEX LOOKUP TABLE (7 Bits for Temperature and 6 Bits for PWM for each Temperature/PWM Pair)
50
51
52
53
54
55
56
57
58
Read.
(Write only
if reg 4A
bit 5 = 1.)
59
5A
5B
5C
5D
5E
5F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
7
0
6:0
0x7F
7:6
00
5:0
0x3F
Lookup Table
Temperature
Entry 1
This bit is unused and always set to 0.
Lookup Table
PWM Entry 1
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 2
This bit is unused and always set to 0.
Lookup Table
PWM Entry 2
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 3
This bit is unused and always set to 0.
Lookup Table
PWM Entry 3
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 4
This bit is unused and always set to 0.
Lookup Table
PWM Entry 4
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 5
This bit is unused and always set to 0.
Lookup Table
PWM Entry 5
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 6
This bit is unused and always set to 0.
Lookup Table
PWM Entry 6
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 7
This bit is unused and always set to 0.
Lookup Table
PWM Entry 7
These bits are unused and always set to 0.
Lookup Table
Temperature
Entry 8
This bit is unused and always set to 0.
Lookup Table
PWM Entry 8
These bits are unused and always set to 0.
Lookup
Table
Hysteresis
These bits are unused and always set to 0
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 51.
The PWM value corresponding to the temperature limit in register 50.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 53.
The PWM value corresponding to the temperature limit in register 52.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 55.
The PWM value corresponding to the temperature limit in register 54.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 57.
The PWM value corresponding to the temperature limit in register 56.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 59.
The PWM value corresponding to the temperature limit in register 58.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 5B.
The PWM value corresponding to the temperature limit in register 5A.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 5D.
The PWM value corresponding to the temperature limit in register 5C.
If the remote diode temperature exceeds this value, the PWM output will
be the value in Register 5F.
The PWM value corresponding to the temperature limit in register 5E.
4FHEX LOOKUP TABLE HYSTERESIS
4F
R/W
7:5
000
4:0
00100
The amount of hysteresis applied to the Lookup Table. (1 LSB = 1°C).
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
23
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 6. Configuration Register
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
03 (09)HEX CONFIGURATION REGISTER
7
0
0
STANDBY
5
0
PWM Disable
in STANDBY
When this bit is a 0, the LM63’s PWM output continues to output the
current fan control signal while in STANDBY.
When this bit is a 1, the PWM output is disabled (as defined by the
PWM polarity bit) while in STANDBY.
4:3
00
These bits are unused and always set to 0.
0
ALERT/Tach
Select
When this bit is a 0, the ALERT/Tach pin is an open drain ALERT
output.
When this bit is a 1, the ALERT/Tach pin is a high-impedance
Tachometer input.
Note that if this bit is set, the function of the ALERT/Tach pin must be
Tach input, so an external ALERT condition will not occur.
T_CRIT Limit
Override
The T_CRIT limit for the remote diode is nominally 85°C. This value
can be changed once after power-up by first setting this bit to a 1,
then programming a new T_CRIT value into the Remote Diode
T_CRIT Limit (register 0x19). The T_CRIT value can not be changed
again except by cycling power to the LM63.
RDTS Fault
Queue
0: an ALERT will be generated if any Remote Diode conversion result
is above the Remote High Set Point or below the Remote Low
Setpoint.
1: an ALERT will be generated only if three consecutive Remote
Diode conversions are above the Remote High Set Point or below
the Remote Low Setpoint.
R/W
2
1
0
24
When this bit is a 0, ALERT interrupts are enabled.
When this bit is set to a 1, ALERT interrupts are masked, and the
ALERT pin is always in a high-impedance (open) state.
When this bit is a 0, the LM63 is in operational mode, converting,
comparing, and updating the PWM output continuously.
When this bit is a 1, the LM63 enters a low-power standby mode.
In STANDBY, continuous conversions are stopped, but a
conversion/comparison cycle may be initiated by writing any value to
register 0x0F. Operation of the PWM output in STANDBY depends
on the setting of bit 5 in this register.
6
03 (09)
ALERT
Mask
0
0
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
Table 7. Tachometer Count And Limit Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
47HEX TACHOMETER COUNT (MSB) and 46HEX TACHOMETER COUNT (LSB) REGISTERS (16 bits: Read LSB first to lock MSB and
ensure MSB and LSB are from the same reading)
47
Read Only
7:0
N/A
Tachometer
Count (MSB)
Read Only
7:2
N/A
Tachometer
Count (LSB)
These registers contain the current 16-bit Tachometer
Count, representing the period of time between tach pulses.
Note that the 16-bit tachometer MSB and LSB are reversed
from the 16-bit temperature readings.
Bits
Edges Used
00:
46
Read Only
1:0
Tachometer
Edge Count
00
Tach_Count_Multiple
Reserved - do not use
01:
2
4
10:
3
2
11:
5
1
Note: If PWM_Clock_Select = 360 kHz, then
Tach_Count_Multiple = 1 regardless of the setting of these
bits.
49HEX TACHOMETER LIMIT (MSB) and 48HEX TACHOMETER LIMIT (LSB) REGISTERS
49
48
R/W
7:0
0xFF
Tachometer
Limit MSB)
R/W
7:2
0xFF
Tachometer
Limit (LSB)
R/W
1:0
[Reserved]
These registers contain the current 16-bit Tachometer
Count, representing the period of time between tach pulses.
Fan RPM = (f * 5,400,000) / (Tachometer Count), where f =
1 for 2 pulses/rev fan; f = 2 for 1 pulse/rev fan; and f = 2/3
for 3 pulses/rev fan. See the APPLICATION NOTES section
at the end of this datasheet for more tachometer
information. Note that the 16-bit tachometer MSB and LSB
are reversed from the 16 bit temperature readings.
Not Used.
Table 8. Local Temperature And Local High Setpoint Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
00HEX LOCAL TEMPERATURE REGISTER (8-bits)
00
Read Only
7:0
N/A
Local Temperature
Reading (8-bit)
8-bit integer representing the temperature of the LM63 die.
05 (0B)HEX LOCAL HIGH SETPOINT REGISTER (8-bits)
05
R/W
7:0
0x46 (70°) Local HIGH Setpoint High Setpoint for the internal diode.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
25
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 9. Remote Diode Temperature, Offset And Setpoint Registers
ADDRESS
HEX
01
READ/
WRITE
Read Only
10
Read Only
11
R/W
12
R/W
07 (0D)
R/W
13
R/W
08 (0E)
14
R/W
R/W
POR
VALUE
NAME
DESCRIPTION
7:0
N/A
Remote Diode
Temperature
Reading (MSB)
This is the MSB of the 2’s complement value, representing the
temperature of the remote diode connected to the LM63. Bit 7 is the
sign bit, bit 6 has a weight of 0x40 (64°), and bit 0 has a weight of 1°C.
This byte to be read first. The LM63C and LM63D will report the actual
thermal diode temperature.
7:5
N/A
4:0
00
BITS
Always 00.
Remote
Temperature
OFFSET (MSB)
These registers contain the value added to or subtracted from the
remote diode’s reading to compensate for the different non-ideality
factors of different processors, diodes, etc. The 2’s complement value,
in these registers is added to the output of the LM63’s ADC to form the
temperature reading contained in registers 01 and 10.
00
7:5
00
4:0
00
Remote
Temperature
OFFSET (LSB)
7:0
0x46
(70°C)
Remote HIGH
Setpoint (MSB)
7:5
00
4:0
00
Remote HIGH
Setpoint (LSB)
7:0
00
(0°C)
Remote LOW
Setpoint (MSB)
7:5
00
4:0
00
Remote LOW
Setpoint (LSB)
Remote Diode
T_CRIT Limit
This 8-bit integer storing the T_CRIT limit is nominally 85°C. This value
can be changed once after power-up by setting T_CRIT Limit Override
(bit 1) in the Configuration register to a 1, then programming a new
T_CRIT value into this register. The T_CRIT Limit can not be changed
again except by cycling power to the LM63.
Remote Diode
T_CRIT
Hysteresis
8-bit integer storing T_CRIT hysteresis. T_CRIT stays activated until
the remote diode temperature goes below [(T_CRIT Limit)—(T_CRIT
Hysteresis)].
19
R/W
7:0
21
R/W
7:0
0x0A
(10°C)
7:3
00000
2:1
Always 00.
High setpoint temperature for remote diode. Same format as Remote
Temperature Reading (registers 01 and 10).
Always 00.
Low setpoint temperature for remote diode. Same format as Remote
Temperature Reading (registers 01 and 10).
Always 00.
These bits are unused and should always set to 0.
00
Remote Diode
Temperature
Filter
0
Comparator
Mode
R/W
0
26
This is the LSB of the 2’s complement value, representing the
temperature of the remote diode connected to the LM63. Bit 7 has a
weight 0.5°C, bit 6 has a weight of 0.25°C, and bit 5 has a weight of
0.125°C.
7:5
0x55
(85°C)
BF
Remote Diode
Temperature
Reading (MSB)
00:
01:
10:
11:
Filter
Filter
Filter
Filter
Disabled
Level 1 (minimal filtering, same as 10)
Level 1 (minimal filtering, same as 01)
Level 2 (maximum filtering)
0: the ALERT/Tach pin functions normally.
1: the ALERTTach pin behaves as a comparator, asserting itself when
an ALERT condition exists, de-asserting itself when the ALERT
condition goes away.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
Table 10. ALERT Status and Mask Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
02HEX ALERT STATUS REGISTER (8-bits) (All Alarms are latched until read, then cleared if alarm condition was removed at the
time of the read.)
7
0
Busy
When this bit is a 0, the ADC is not converting.
When this bit is set to a 1, the ADC is performing a conversion. This bit
does not affect ALERT status.
6
0
Local
High Alarm
When this bit is a 0, the internal temperature of the LM63 is at or below
the Local High Setpoint.
When this bit is a 1, the internal temperature of the LM63 is above the
Local High Setpoint, and an ALERT is triggered.
5
0
4
3
0x02
This bit is unused and always read as 0.
0
Remote
High Alarm
When this bit is a 0, the temperature of the Remote Diode is at or
below the Remote High Setpoint.
When this bit is a 1, the temperature of the Remote Diode is above the
Remote High Setpoint, and an ALERT is triggered.
0
Remote
Low Alarm
When this bit is a 0, the temperature of the Remote Diode is at or
above the Remote Low Setpoint.
When this bit is a 1, the temperature of the Remote Diode is below the
Remote Low Setpoint, and an ALERT is triggered.
0
Remote Diode
Fault Alarm
When this bit is a 0, the Remote Diode appears to be correctly
connected.
When this bit is a 1, the Remote Diode may be disconnected or
shorted. This Alarm does not trigger an ALERT.
0
Remote
T_CRIT Alarm
When this bit is a 0, the temperature of the Remote Diode is at or
below the T_CRIT Limit.
When this bit is a 1, the temperature of the Remote Diode is above the
T_CRIT Limit, and an ALERT is triggered..
Tach Alarm
When this bit is a 0, the Tachometer count is lower than or equal to the
Tachometer Limit (the RPM of the fan is greater than or equal to the
minimum desired RPM).
When this bit is a 1, the Tachometer count is higher than the
Tachometer Limit (the RPM of the fan is less than the minimum
desired RPM), and an ALERT is triggered. Note that if this bit is set,
the function of the ALERT/Tach pin must be Tach input, so an external
ALERT condition will not be generated. The user may read the status
register periodically to find out if and ALERT condition has occurred.
Read Only
2
1
0
0
16HEX ALERT MASK REGISTER (8-bits)
7
16
1
This bit is unused and always read as 1.
Local High
Alarm Mask
When this bit is a 0, a Local High Alarm event will generate an ALERT.
When this bit is a 1, a Local High Alarm will not generate an ALERT
6
0
5
1
4
0
Remote
High Alarm Mask
When this bit is a 0, Remote High Alarm event will generate an
ALERT.
When this bit is a 1, a Remote High Alarm event will not generate an
ALERT.
3
0
Remote
Low Alarm
Mask
When this bit is a 0, a Remote Low Alarm event will generate an
ALERT.
When this bit is a 1, a Remote Low Alarm event will not generate an
ALERT.
2
1
1
0
Remote
T_CRIT
Alarm Mask
When this bit is a 0, a Remote T_CRIT event will generate an ALERT.
When this bit is a 1, a Remote T_CRIT event will not generate an
ALERT.
0
0
Tach
Alarm Mask
When this bit is a 0, a Tach Alarm event will generate an ALERT.
When this bit is a 1, a Tach Alarm event will not generate an ALERT.
This bit is unused and always read as 1.
R/W
This bit is unused and always read as 1.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
27
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
Table 11. Conversion Rate And One-Shot Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
04 (0A)HEX CONVERSION RATE REGISTER (8-bits)
04 (0A)
R/W
7:0
0x08
Conversion
Rate
Sets the conversion rate of the LM63.
00000000 = 0.0625 Hz
00000001 = 0.125 Hz
00000010 = 0.25 Hz
00000011 = 0.5 Hz
00000100 = 1 Hz
00000101 = 2 Hz
00000110 = 4 Hz
00000111 = 8 Hz
00001000 = 16 Hz
00001001 = 32 Hz
All other values = 32 Hz
04 (0A)HEX ONE-SHOT REGISTER (8-bits)
Write
Only
0F
7:0
One Shot
Trigger
N/A
With the LM63 in the STANDBY mode a single write to this register will
initiate one complete temperature conversion cycle.
Table 12. ID Registers
ADDRESS
HEX
READ/
WRITE
BITS
POR
VALUE
NAME
DESCRIPTION
FFHEX STEPPING / DIE REVISION ID REGISTER (8-bits)
Read
Only
FF
7:0
0x41
Stepping/Die
Revision ID
Version of LM63
FEHEX MANUFACTURER’S ID REGISTER (8-bits)
FE
28
Read
Only
7:0
0x01
Manufacturer’s ID
0x01 = Texas Instruments
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
APPLICATION NOTES
FAN CONTROL DUTY CYCLE VS. REGISTER SETTINGS AND FREQUENCY
PWM
FREQ AT
1.4 kHz
INTERNAL
CLOCK, Hz
ACTUAL
DUTY
CYCLE, %
WHEN
75% IS
SELECTED
180.0
703.1
50.0
90.00
351.6
75.0
3
60.00
234.4
83.3
4
45.00
175.8
75.0
8
5
36.00
140.6
80.0
12
9
6
30.00
117.2
75.0
14
11
7
25.71
100.4
78.6
6.25
16
12
8
22.50
87.9
75.0
9
5.56
18
14
9
20.00
78.1
77.8
10
5.00
20
15
10
18.00
70.3
75.0
11
4.54
22
17
11
16.36
63.9
77.27
12
4.16
24
18
12
15.00
58.6
75.00
13
3.85
26
20
13
13.85
54.1
76.92
14
3.57
28
21
14
12.86
50.2
75.00
15
3.33
30
23
15
12.00
46.9
76.67
16
3.13
32
24
16
11.25
43.9
75.00
17
2.94
34
26
17
10.59
41.4
76.47
18
2.78
36
27
18
10.00
39.1
75.00
19
2.63
38
29
19
9.47
37.0
76.32
20
2.50
40
30
20
9.00
35.2
75.00
21
2.38
42
32
21
8.57
33.5
76.19
22
2.27
44
33
22
8.18
32.0
75.00
23
2.17
46
35
23
7.82
30.6
76.09
24
2.08
48
36
24
7.50
29.3
75.00
25
2.00
50
38
25
7.20
28.1
76.00
26
1.92
52
39
26
6.92
27.0
75.00
27
1.85
54
41
27
6.67
26.0
75.93
28
1.79
56
42
28
6.42
25.1
75.00
29
1.72
58
44
29
6.21
24.2
75.86
30
1.67
60
45
30
6.00
23.4
75.00
31
1.61
62
47
31
5.81
22.7
75.81
STEP
RESOLUTION,
%
PWM
VALUE
4D [5:0]
FOR 100%
PWM
VALUE
4C [5:0] FOR
ABOUT 75%
1
50
2
1
1
2
25
4
3
2
3
16.7
6
5
4
12.5
8
6
5
10.0
10
6
8.33
7
7.14
8
PWM
FREQ
4D [4:0]
0
PWM
VALUE
4C [5:0]
FOR 50%
PWM
FREQ AT
360 kHz
INTERNAL
CLOCK, kHz
Address 0 is mapped to Address 1
COMPUTING DUTY CYCLES FOR A GIVEN FREQUENCY
Select a PWM Frequency from the first column corresponding to the desired actual frequency in columns 6 or 7.
Note the PWM Value for 100% Duty Cycle.
Find the Duty Cycle by taking the PWM Value of Register 4C and computing:
DutyCycle _(%) =
PWM _Value
PWM _Value _ for _ 100 %
u 100 %
(1)
Example: For a PWM Frequency of 24, a PWM Value at 100% = 48 and PWM Value actual = 28, then the Duty
Cycle is (28/48) × 100% = 58.3%.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
29
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
REQUIRED INITIAL FAN CONTROL REGISTER SEQUENCE
Important! The BIOS must follow the sequence listed in Table 13 to configure the following Fan Registers for the
LM63 before using any of the Fan or Tachometer or PWM registers.
Table 13. [Register]HEX and Setup Instructions
[Register]HEX AND SETUP INSTRUCTIONS (1)
STEP
(1)
1
[4A] Write bits 0 and 1; 3 and 4. This includes tach settings if used, PWM internal clock select (1.4 kHz or 360 kHz) and PWM
Output Polarity.
2
[4B] Write bits 0 through 5 to program the spin-up settings.
3
[4D] Write bits 0 through 4 to set the frequency settings. This works with the PWM internal clock select.
4
Choose, then write, only one of the following:
A. [4F–5F] the Lookup Table, or
B. [4C] the PWM value bits 0 through 5.
5
If Step 4A, Lookup Table, was chosen and written then write [4A] bit 5 = 0.
All other registers can be written at any time after the above sequence.
COMPUTING RPM OF THE FAN FROM THE TACH COUNT
The Tach Count Registers 46HEX and 47HEX count the number of periods of the 90 kHz tachometer clock in the
LM63 for the tachometer input from the fan assuming a 2 pulse per revolution fan tachometer, such as the fans
supplied with the Pentium 4 boxed processors. The RPM of the fan can be computed from the Tach Count
Registers 46HEX and 47HEX. This can best be shown through an example.
EXAMPLE:
Given: the fan used has a tachometer output with 2 per revolution.
Let:
• Register 46 (LSB) is BFHEX = Decimal (11 x 16) + 15 = 191 and
• Register 47 (MSB) is 7HEX = Decimal (7 x 256) = 1792.
The total Tach Count, in decimal, is 191 + 1792 = 1983.
The RPM is computed using the formula
f u 5, 400 , 000
Fan _ RPM =
,
Total _ Tach _ Count _( Decimal )
where
•
•
•
f = 1 for 2 pulses/rev fan tachometer output;
f = 2 for 1 pulse/rev fan tachometer output, and
f = 2 / 3 for 3 pulses/rev fan tachometer output
(2)
For our example
Fan _ RPM =
1 u 5, 400 , 000
= 2723 _ RPM
1983
30
(3)
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
USE OF THE LOOKUP TABLE FOR NON-LINEAR PWM VALUES VS TEMPERATURE
The Lookup Table, Registers 50 through 5F, can be used to create a non-linear PWM vs Temperature curve that
could be used to reduce the acoustic noise from processor fan due to linear or step transfer functions. An
example is given below.
EXAMPLE:
In a particular system it was found that the best acoustic fan noise performance was found to occur when the
PWM vs Temperature transfer function curve was parabolic in shape.
From 25°C to 105°C the fan is to go from 20% to 100%. Since there are 8 steps to the Lookup Table we will
break up the Temperature range into 8 separate temperatures. For the 80°C over 8-steps = 10°C per step. This
takes care of the x-axis.
For the PWM Value, we first select the PWM Frequency. In this example, we will make the PWM Frequency
(Register 4C) 20.
For 100% Duty Cycle then, the PWM value is 40. For 20%, the minimum is 40 x (0.2) = 8.
We can then arrange the PWM, Temperature pairs in a parabolic fashion in the form of y = 0.005 • (x −25)2 + 8
TEMPERATURE
PWM VALUE
CALCULATED
CLOSEST PWM
VALUE
25
8.0
8
35
8.5
9
45
10.0
10
55
12.5
13
65
16.0
16
75
20.5
21
85
26.0
26
95
32.5
33
105
40.0
40
We can then program the Lookup Table with the temperature and Closest PWM Values required for the curve
required in our example.
NON-IDEALITY FACTOR AND TEMPERATURE ACCURACY
The LM63 can be applied to remote diode sensing in the same way as other integrated-circuit temperature
sensors. It can be soldered to a printed-circuit board, and because the path of best thermal conductivity is
between the die and the pins, its temperature will effectively be that of the printed-circuit board lands and traces
soldered to its pins. This presumes that the ambient air temperature is nearly the same as the surface
temperature of the printed-circuit board. If the air temperature is much higher or lower than the surface
temperature, the actual temperature of the LM63 die will be an intermediate temperature between the surface
and air temperatures. Again, the primary thermal conduction path is through the leads, so the circuit board
surface temperature will contribute to the die temperature much more than the air temperature.
To measure the temperature external to the die use a remote diode. This diode can be located on the die of the
target IC, such as a CPU processor chip as shown in Figure 14, allowing measurement of the IC’s temperature,
independent of the LM63’s temperature. The LM63 has been optimized for use with the thermal diode on the die
of an Intel Pentium 4 or a Mobile Pentium 4 Processor-M processor.
2
IE = IF
3
PROCESSOR
IC
D+
2.2 nF
IR
D-
LM63
Figure 14. Processor Connection to LM63
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
31
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
A discrete diode can also be used to sense the temperature of external objects or ambient air. Remember that a
discrete diode’s temperature will be affected, and often dominated by, the temperature of its leads.
Most silicon diodes do not lend themselves well to this application. It is recommended that a diode-connected
2N3904 transistor be used, as shown in Figure 15. The base of the transistor is connected to the collector and
becomes the anode. The emitter is the cathode.
IF
MMBT3904
2
D+
2.2 nF
3
IR
D-
LM63
Figure 15. Processor Connection to LM63
A LM63 with a diode-connected 2N3904 transistor approximates the temperature reading of the LM63 with the
Pentium 4 processor by 1°C.
T2N3904 = TPENTIUM 4 − 1°C
(4)
DIODE NON-IDEALITY
When a transistor is connected to a diode the following relationship holds for Vbe, T, and IF:
ª §¨¨ Vbe ·¸¸
K ˜V
I S ˜ «e © T ¹
«
¬
IF
º
1»
»
¼
where
V =
T
•
•
•
•
•
•
•
(5)
kT
q
q = 1.6x10−19 Coulombs (the electron charge)
T = Absolute Temperature in Kelvin
k = 1.38x10−23 joules/K (Boltzmann’s constant)
η is the non-ideality factor of the manufacturing process used to make the thermal diode
Is = Saturation Current and is process dependent
If = Forward Current through the base emitter junction
Vbe = Base Emitter Voltage Drop
(6)
In the active region, the −1 term is negligible and may be eliminated, yielding the following equation
IF
ª §¨¨ Vbe ·¸¸º
K ˜V
IS ˜ «e © T ¹»
»
«
¼
¬
(7)
In Equation 7, η and Is are dependent upon the process that was used in the fabrication of the particular diode.
By forcing two currents with a very controlled ratio (N) and measuring the resulting voltage difference, it is
possible to eliminate the Is term. Solving for the forward voltage difference yields the relationship:
' Vbe
§ kT ·
¸ ˜ ln N
¨ q ¸
¹
©
K¨
(8)
32
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
The voltage seen by the LM63 also includes the IF×RS voltage drop across the internal series resistance of the
Pentium 4 processor’s thermal diode. The non-ideality factor, η, is the only other parameter not accounted for
and depends on the diode that is used for measurement. Since ΔVbe is proportional to both η and T, the
variations in η cannot be distinguished from variations in temperature. Since the temperature sensor does not
control the non-ideality factor, it will directly add to the inaccuracy of the sensor.
For the Intel Pentium 4 and Mobile Pentium 4 Processor-M processors Intel specifies a ±0.1% variation in η from
part to part. As an example, assume that a temperature sensor has an accuracy specification of ±1%°C at room
temperature of 25°C and process used to manufacture the diode has a non-ideality variation of ±0.1%. The
resulting accuracy will be:
TACC = ±1°C + (±0.1% of 298°K) = ±1.3°C
(9)
The additional inaccuracy in the temperature measurement caused by η, can be eliminated if each temperature
sensor is calibrated with the remote diode that it will be paired with. Refer to the processor datasheet for the nonideality factor.
COMPENSATING FOR DIODE NON-IDEALITY
In order to compensate for the errors introduced by non-ideality, the temperature sensor is calibrated for a
particular processor. Texas Instruments temperature sensors are always calibrated to the typical non-ideality of a
particular processor type.
The LM63 is calibrated for the non-ideality of the 0.13 micron Intel Pentium 4 and Mobile Pentium 4 Processor-M
processors.
When a temperature sensor, calibrated for a specific type of processor is used with a different processor type or
a given processor type has a non-ideality that strays form the typical value, errors are introduced.
Temperature errors associated with non-ideality may be introduced in a specific temperature range of concern
through the use of the Temperature Offset Registers 11HEX and 12HEX.
The user is encouraged to send an e-mail to [email protected] to further request information on
our recommended setting of the offset register for different processor types.
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
33
LM63
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
www.ti.com
PCB LAYOUT FOR MINIMIZING NOISE
Figure 16. Ideal Diode Trace Layout
In a noisy environment, such as a processor mother board, layout considerations are very critical. Noise induced
on traces running between the remote temperature diode sensor and the LM63 can cause temperature
conversion errors. Keep in mind that the signal level the LM63 is trying to measure is in microvolts. The following
guidelines should be followed:
1. Use a low-noise +3.3VDC power supply, and bypass to GND with a 0.1 µF ceramic capacitor in parallel with
a 100 pF ceramic capacitor. A bulk capacitance of 10 µF needs to be in the vicinity of the LM63's VDD pin.
2. Place the100 pF power supply bypass capacitor as close as possible to the VDD pin and the recommended
2.2 nF diode capacitor as close as possible to the LM63's D+ and D− pins. Make sure the traces to the
2.2 nF capacitor are matched.
3. Ideally, the LM63 should be placed within 10 cm of the Processor diode pins with the traces being as
straight, short and identical as possible. Trace resistance of 1 Ω can cause as much as 1°C of error. This
error can be compensated by using the Remote Temperature Offset Registers, since the value placed in
these registers will automatically be subtracted from or added to the remote temperature reading.
4. Diode traces should be surrounded by a GND guard ring to either side, above and below if possible. This
GND guard should not be between the D+ and D− lines. In the event that noise does couple to the diode
lines it would be ideal if it is coupled common mode. That is equally to the D+ and D− lines.
5. Avoid routing diode traces in close proximity to power supply switching or filtering inductors.
6. Avoid running diode traces close to or parallel to high-speed digital and bus lines. Diode traces should be
kept at least 2 cm apart from the high-speed digital traces.
7. If it is necessary to cross high-speed digital traces, the diode traces and the high-speed digital traces should
cross at a 90 degree angle.
8. The ideal place to connect the LM63's GND pin is as close as possible to the Processor's GND associated
with the sense diode.
9. Leakage current between D+ and GND should be kept to a minimum. One nano-ampere of leakage can
cause as much as 1°C of error in the diode temperature reading. Keeping the printed circuit board as clean
as possible will minimize leakage current.
Noise coupling into the digital lines greater than 400 mVp-p (typical hysteresis) and undershoot less than 500 mV
below GND, may prevent successful SMBus communication with the LM63. SMBus no acknowledge is the most
common symptom, causing unnecessary traffic on the bus. Although the SMBus maximum frequency of
communication is rather low (100 kHz max), care still needs to be taken to ensure proper termination within a
system with multiple parts on the bus and long printed circuit board traces. An RC lowpass filter with a 3 dB
corner frequency of about 40 MHz is included on the LM63's SMBCLK input. Additional resistance can be added
in series with the SMBData and SMBCLK lines to further help filter noise and ringing. Minimize noise coupling by
keeping digital traces out of switching power supply areas as well as ensuring that digital lines containing highspeed data communications cross at right angles to the SMBData and SMBCLK lines.
34
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
LM63
www.ti.com
SNAS190E – SEPTEMBER 2002 – REVISED MAY 2013
REVISION HISTORY
Changes from Revision D (May 2013) to Revision E
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 34
Submit Documentation Feedback
Copyright © 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM63
35
PACKAGE OPTION ADDENDUM
www.ti.com
3-May-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM63CIMA
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 125
LM63
CIMA
LM63CIMA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 125
LM63
CIMA
LM63CIMAX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 125
LM63
CIMA
LM63CIMAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 125
LM63
CIMA
LM63DIMA
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
0 to 125
LM63
DIMA
LM63DIMA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 125
LM63
DIMA
LM63DIMAX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
0 to 125
LM63
DIMA
LM63DIMAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
0 to 125
LM63
DIMA
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
3-May-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM63CIMAX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM63CIMAX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM63DIMAX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM63DIMAX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM63CIMAX
SOIC
D
8
2500
367.0
367.0
35.0
LM63CIMAX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM63DIMAX
SOIC
D
8
2500
367.0
367.0
35.0
LM63DIMAX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated