SAMPLING DEVICE SERIES FOR GAS ANALYZER DATA SHEET GAS EXTRACTOR (model: ZBA) Page 2 GAS FILTER GAS WASHING SEPARATOR AND WASHING NOZZLE SO3 MIST CATCHER (model: ZBB ) Page 6 PELTIER GAS COOLER (model: ZBC) GAS DRYER (model: ZBJ) (Semi-permeable membrane vapor phase dehumidifier) Page 9 FLOW METER AND REGULATOR (model: ZBD) Page 12 BALL VALVES AND SELECTOR VALVES (model: ZBF) Page 14 GAS ASPIRATOR (model: ZBG) Page 15 DRAININGS & OTHERS (model: ZBH) Page 16 GAS CONVERTER (model: ZDL) Page 18 STANDARD GAS (model: ZBM) Page 20 EDS3-1i Date Aug. 29, 2011 ■ GAS EXTRACTOR (model: ZBA) SPECIFICATIONS Type System Gas temperature ZBAK2 ZBAS1 ZBAB Electric heating (Standard type) Electric heating (Applicable to high dust) For cleaning gas extraction (Without filter) 800°C max./SUS probe 1300°C max./SiC probe (Note 1) 800°C max./SUS probe 100°C to 800°C (ZBAB0W) 100°C to 1000°C (ZBAB1T) Electric heating system applicable to high temperature Amount of dust (guideline): Up to 100mg/N m 3 Features Applicable to large amount of dust Amount of dust (guideline): Up to 20g/Nm 3 Simple type intended for the environment relatively small in amount of dust Amount of dust (guideline): Up to 10mg/Nm 3 Material of part contacting gas SUS316, Viton SUS316, Viton SUS316, 304 (ZBAB0W) Titanium (ZBAB1T) Sampling pipe SUS 316, SiC SUS 316 SUS316, 304 (ZBAB0W) Titanium (ZBAB1T) JIS 5k 65AFF (Note 2) JIS 10k 50AFF (Note 2) Companion flange SUS316 mesh, Filtering capacity: 40µm Filter Response time (excluding sampling pipe) Mass (approx.) Sample gas outlet Heater JIS 5k 65AFF (ZBAB0W) JIS 5k 25AFF (ZBAB1T) SUS316 mesh, Filtering capacity: 10µm (Note 2) — 90% response at 3L/min: Approx. 25s 90% response at 3L/min: Approx. 16s 90% response at 3L/min: Approx. 8s 9kg (Excluding sampling pipe) 20kg (Excluding sampling pipe) 3.5kg (Excluding sampling pipe) Rc1/2 Rc1/2 Rc1/2 100V AC 100VA 100V AC 400VA — Installation Outdoor installation Note 1) The flow rate of sample gas should be kept at 1L/min. or lower for applications to high temperature gases. Contact us for applications to gases at flow rate higher than 1L/min. Note 2) Flange of other specifications are also available. Contact us for details. CODE SYMBOLS 1 2 3 4 5 6 7 8 ZBA 9 10 11 Description 5 B B K S System (4th, 5th, and 6th digits) Unheated type, SUS Unheated type, titanium Electric heating type (Standard) Electric heating type (Applicable to high dust) Insertion length (L) (7th digit) 0mm 300mm L 400mm 600mm 800mm Gas temperature: 800°C max. (Material: SUS316) 1000mm 0W 1T 2W 1W Y A B C E G H J K D F 0 2 5 7 A A G Y A 2 1200mm 1500mm 2000mm 700mm ZBAK gas temperature: 1300°C max. (Material: SUS, SiC) 900mm Gas output joint (9th digit) Nipple Current tap socket ZBAS: Specify this. Without Without ZBAB0: Specify either For ø10/ø8mm Teflon tube Without one of the two. Without With ZBAK For ø10/ø8mm Teflon tube With For ø10/ø8mm Teflon tube (Elbow) Without Flange (10th digit) JIS 5k 65AFF JIS 5k 25AFF Heating tube terminal support (11th digit) Without ZBAB0, 1: Specify this. With Details of selection *ZBAS: Specify one from Y to K. *ZBAB: Specify one from Y to G. *Material of ZBAB1: Titanium Gas temperature: 1000°C max. *ZBAK: Any one can be specified. *ZBAS: Specify 0. *ZBAB0: Specify either 0 or 2. *ZBAB1: Specify A. *ZBAK: Specify one from 0, 2, 5, and 7. When 5 or 7 is specified, the 11th digit is set to Y. A is unavailable. *ZBAS: Specify up to the 9th digit. (Not required) *ZBAB1: Specify G. *ZBAS: Specify up to the 9th digit. (Not required) *ZBAB0, 1: Specify Y. OUTLINE (Unit: mm) ø155 Rc 1/2 gas outlet Top Handle for filter replacement Cover (750) 357 Heating tube support (when heating tube is provided) 212 Wiring port G1/2 293 Terminal box (76) Rc 3/4 Main nameplate Packing Flange JIS 5K 65AFF SUS316 Sampling pipe 20A 4-ø15 ø130 ø155 Code for 7th digit Y: (Not supplied) A (300) G (1000) B (400) H (1200) C (600) J (1500) E (800) K (2000) Z: (By order) Gas inlet ø27 Packing SiC sampling pipe Code for 7th digit Y (Not supplied) D (700) F (900) ø30 Gas inlet Electric heating type (For high temperature application) (ZBAK2) Lock Approx. 88 125 300 ø155 ø120 Pipe Blow2 Blow1 Gas outlet (Rc1/2) Code for 7th digit C (600) E (800) G (1000) Packing Terminal Flange 3-Rc 1/2 Sample Cable glands Approx. 216 With ø10 teflon join Cable Sampling pipe ø21.7 Gas inlet Blow2 Cover Case 4–ø15 ø13 0 2-A15c 60 Sample ø34 4-ø19 250 (Rc1/2 with plug) 14 (600) Thermostat Approx. 350 Approx. 1003 120 280 16 Heater ø155 For cable Approx. 177 2-A30a Blow1 (ZBAS1) Flange JIS 5K 65AFF (ZBAB0W) 3 Gas outlet joint 43 (300) (400) (600) (800) (1000) ø8 ø10 10 33 (67) Coupling for ø10/ø8 (internal diameter) Teflon tube A B C E G : : : : : R1/2 Material: Teflon ø22 ø10 (For ZBAK, ZBAB0) Code for 7th digit 31 (ø21.7) Gas inlet ø8 32 4-ø12 RC1/2 R1/2 Material: Teflon Current tap socket ø75 R1/2 Flange Approx. 47 Approx. 120 Rc1/2 95 (ZBAB1) Rc1/2 Material: Teflon (Unit: mm) SCOPE OF DELIVERY ZBAK2 : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4, O-ring (G50, G45) × 1 each or 2 each (for high temperature application) ZBAS1 : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4, O-ring (G50) × 1, O-ring (G65) × 1 ZBAB : Main unit, sampling pipe, packing for flange × 1, bolt and nut × 4 CONSUMABLE PARTS/SPARE PARTS Name Spare parts of ZBAK2 for 1 year (for general application) ZBN5BA3 Wire mesh filter 40µm × 1, O-ring (G50, G45) × 1 each, Packing for wire mesh filter × 1 Spare parts of ZBAK2 for 1 year (for high temperature application) ZBN5BA4 Wire mesh filter × 1, O-ring (G50, G45) × 2 each, Packing for wire mesh filter × 2 Spare parts of ZBAS1 for 1 year ZBN3BA6 Wire mesh filter 10µm × 2, O-ring (G50) × 4, O-ring (G65) × 4 Wire mesh filter 40µm (for ZBAK2) ZBNL1012 For ZBAK1, 2 O-ring (G50) (Pack of 10) ZBNN1152 For ZBAK2, ABAS1 O-ring (G45) (Pack of 10) ZBNN1182 For ZBAK2 Packing for wire mesh filter (Pack of 10) ZBNN1162 For ZBAK2 Coupling for ø10/ø8mm Teflon tube 4 Order code TK745559P1 TK745559P2 TK745559P10 For ZBAK1 (R1/4) For ZBAK2, ABAB0 (R1/2) For ZBAB1 (R1/2 elbow) ■ GAS FILTER (model: ZBB) SPECIFICATIONS 1. Gas Filter Model ZBBB1V03-0 / ZBBB1V13-2 Application Primary filter for gas without drain Filter material Glass wool ZBBB2V03-0 For elimination of SO2 and SO3 For elimination of SO3 PVC (transparent) , chloroprene (O-ring) PVC (transparent) Operating temperature 0°C to 45°C Withstanding pressure 50kPa Required when about half of the filter element is contaminated by dust. Steel wool filter requires replacement when it is deteriorated. Connection port Gas inlet and outlet Rc 1/4 Mass (approx.) Ceramic Steel wool (Bonstar #0) (about 200 g) Materials of gas-contacting parts Filter replacement ZBBB3V03-0 / ZBBB4V03-0 0.8 kg / 0.6 kg At SO3 concentration of 30ppm: Replace once in 4 months (ZBBB3). Replace once in 8 months (ZBBB4). Hose end ø6, Upright attachment 1 kg Response time (at flow rate 1L/min) 0.1 kg / 0.3 kg About 30 sec for 90% indication Pressure resistance About 0.1 kPa (at 5L/min) About 4 kPa (at 1L/min) CONSUMABLE AND SPARE PARTS For 1-year analysis • ZBN3BB12 (for ZBBB1V03) Glass wool × 36, O-ring (G65) × 2 • ZBN3BBC2 (for ZBBB1V13) Glass wool × 12, O-ring (G65) × 2 • ZBN3BB22 (for ZBBB2V) Steel wool × 3, O-ring × 2 • ZBN3BB82 (for ZBBB3V) Replacement mist catcher × 3, Ancillary fitting × 1 • ZBN3BB92 (for ZBBB4V) Replacement mist catcher × 2, Ancillary fitting × 1 2. Membrane Filter ZBBM2V 3-0 Type Application ZBBM6V03-0 ZBBM4V 3-0 ZBBM7V03-0 Final-stage filter and monitoring filter of analyzer Main materials of gas-contacting parts Connection port Filter element: Glass fiber filter paper (ø55) O-ring : Chloroprene Body : PVC (transparent) Gas inlet and outlet Rc1/4 Gas inlet and outlet ø6.4 hose port Filter element: Teflon (ø55) O-ring : Chloroprene Body : PVC (transparent) Gas inlet and outlet Rc1/4 : CODE 0 : general 1 : small volume type 2 : 30kpa pressure type 3 : 1+ 2 Gas inlet and outlet ø6.4 hose port Operating temperature -10°C to 45°C 30 kPa (7th code 2 or 3) Withstanding pressure 5 kPa (7th code 0) Response for 90% indication Approx. 3 sec (at 1L/min) with standard type (7th code 0) Approx. 1.5 sec (at 1L/min) with high speed type (7th code 1 or 3) Installation On vertical panel face (gas inlet being bottom, outlet being top) Mass Approx. 160 g Pressure resistance Approx. 0.1 kPa (at 1L/min) Approx. 4.3 kPa (at 1L/min) CONSUMABLE AND SPARE PARTS Body type Part name Filter paper ZBNC6102 Fluoropore filter paper ZBN C6302 ZBBM2V ZBBM6V ZBBM4V ZBBM7V Remarks 100 sheet / 1 box 12 to 50 sheet /year 6 to 24 sheets /year 10 sheet / 1 box For 1-year analysis • ZBN3BB52 (for ZBBM2) Filter paper 25 sheets, O-ring G65 × 1, P49 x 1 • ZBN3BB72 (for ZBBM4) Fluoropore filter 12 sheets, O-ring G65 x 1, P49 x 1 • ZBN3BBA2 (for ZBBM6) Filter paper 25 sheets, O-ring G65 x 1, Rubber ring x 1 • ZBN3BBB2 (for ZBBM7) Fluoropore filter 12 sheets, O-ring G65 x 1, Rubber ring x 1 5 3. Mist filter Model ZBBK1V03-0 ZBBK2V03-0 Drain separation, mist/dust removal, for general exhaust gas Drain separation, dust Same as left (with space removal, for SO2 analysis, for drain separation) for comparatively clean exhaust gas Main materials of gas-contacting parts Glass fiber Cellulose Phenol resin Chloroprene PVC Polyethylene Pore size Double structure of approx. 40 and 5µm Application PVC (2)O-ring (JISG65) •ZBNN1012 (For ZBBK1, 2, 4) (10 pcs/set) approx. 5µm 0°C to 45°C Inlet/outlet Rc1/4 Drain port: ø13 hose port Rc1/4 Connection port Withstanding pressure 20kPa Internal volume Approx. 200 cm 3 Approx. 300 cm3 Approx. 4 sec for 90% indication (at flow rate 5L/min) Installation Approx. 7 sec Vertical installation on wall face Mass Pressure resistance (1)Filter element •ZBNH2012 (for ZBBK2, 4) 2 pcs/set •ZBNH1002 (for ZBBK1) 1 pc./set •ZBNH2002 (for ZBBK2) 1 pc./set Chloroprene Operating temperature Response time CONSUMABLE AND SPARE PARTS ZBBK4V03-0 (3)Requirement for 1 year (guideline when used for oil burning exhaust gas) •ZBN3BB32 (for ZBBK1) (Filter × 3, O-ring G65 × 2) •ZBN3BB42 (for ZBBK2, 4) (Filter × 3, O-ring G65 × 2) Approx. 0.6 kg Approx. 0.1 kPa (Dry) (flow rate 5L/min) Approx. 0.4 kPa (Wet) (flow rate 5L/min) Approx. 0.35 kPa (flow rate 5L/min) Approx. 2.6 kPa (flow rate 5L/min) 4. Gas Washing Separator and Washing Nozzle Washing nozzle (ZBBH2 W03-0) Gas washing separator (ZBBF W03- ) Suction of dusty gas, washing with water and separation of water and gas Washing water: 100 to 200 kPa, Typically 5 to 10L/min depending on furnace pressure and sampling pressure loss Suction rate: Approx. 8L/min (water volume 8R/min, 160 mm water sealing, vertical piping of 1 m length) Ambient temperature: 0°C to 60°C Ambient temperature: 0°C to 60°C Connection port:Washing nozzle; Washing nozzle inlet Rc1/2 Gas inlet Rc11/4 Outlet Rc1/2 Blowback air inlet Rc1/2 Gas washing separator; Inlet R1/2 Gas outlet R1/2 Water outlet R1 Drain port Rc1/2 Main material of gas-contacting parts: SUS 316 Mass: Washing nozzle; approx. 3 kg Gas washing separator; approx. 15 kg (ZBBF2W) Discharge pressure: 2.1kPa at max. (When 2 is selected as the 5th digit of the code symbols) 5kPa at max. (When 5 is selected as the 5th digit of the code symbols) 2.1 to 6kPa (When 9 is selected as the 5th digit of the code symbols) Gas outlet coupling: None (When 0 is selected as the 9th digit of the code symbols) For ø10/ø8 mm Teflon tube (When 2, 3 is Model: Functions: 6 selected as the 9th digit of the code symbols) Note: For washing, use the water that has undergone degassing processing. Otherwise indication error of O2 gauge (in the case of micro O2 gauge) of decrease of suction flow rate may result. Application Example Washing water Valve Washing nozzle (ZBBH2W) Gas extractor Blowback air inlet 1 m or longer vertical pipe required Avoid use of an elbow. Union R100 min. Gas outlet Gas washing separator (ZBBF W) Water outlet Drain The asterisked parts and pipes are optional parts. OUTLINE ( Unit : mm ) 16 200 16 200 Space for filter replacement ø100 Space for filter replacement ø100 25 30 18 10 INLET ø60 Drain port 105 Gas outlet Rc1/4 2-ø7 mounting hole Rc1/4 Gas inlet A B ZBBK1, 2 ZBBK4 36 54 160 212 (ZBBK1,2) Rc1/4 55 Transparent 25 Approx. 34 A 80 This part is made of PVC (transparent) . Gas inlet Rc1/4 DRAIN 55 30 55 ø60 Drain port DRAIN (ZBBK4) 105 INLET 50 228 80 OUTLET Gas outlet Rc1/4 2-ø7 mounting hole B 10 30 OUTLET 100 Rc1/4 30 Drain ø13 100 Gas filter (ZBBB1V03-0) (ZBBB2V03-0) Space for filter replacement Gas outlet Gas inlet 25 2-ø7 mounting hole Transparent ø10/ø8 coupling for Teflon tube 100 C 55 B A 150 80 ø60 17 30 18 55 INLET 10 16 ø100 200 Mist filter (ZBBK) 2-Rc1/4 Gas outlet OUTLET 105 Gas inlet ø6 hose end (with cap) A Gas filter (ZBBB1V13-2) B ZBBB3 Approx. 242 ø22 ZBBB4 Approx. 272 ø48 C Mass ø29 ø57 0.1kg 0.3kg SO3 Mist catcher (ZBBB3V) (ZBBB4V) 7 36 24.4 13.2 3 4-ø5 (or 4-M4) 2-ø25 hole UP 20 60 28 28 ø20 20 ø8 ø4.5 ø100 40 Gas outlet Gas inlet Rc1/4 60 112 Panel mounting dimensions (ZBBM2V, ZBBM4V) Membrane filter (ZBBM2V, ZBBM4V) Approx. 29 10 4-ø5 (or 4-M4) 18 Gas outlet 29.5 20 63.6 29.5 20 ø6.4 2-ø25 hole Gas inlet 63.6 6 Membrane filter (ZBBM6V, ZBBM7V) Panel mounting dimensions (ZBBM6V, ZBBM7V) Washing water inlet R1/2 To gas washing separator Rc1/2 Washing nozzle (ZBBH2W) Rc1/2 Drain L = 210 (ZBBF2W ) L = 500 (ZBBF5W ) L = as specified (ZBBF9W) Ball valve 1/2 for water discharge 9th digit code 0, 1 and 2: Ball valve 108 102 Approx. L + 271 Approx.132 4-ø10 mounting hole Water discharge Rc1/2 Drain 9th digit code 3: Ball valve Gas washing separator (ZBBF) 4 100 to 150 Approx. L + 229 60° Blowback air inlet Rc1/2 8 R1 20 220 Approx. 90 Approx. 200 Sampling gas inlet Rc11/4 Gas outlet Rc1/2 94 55 R1/2 Approx. 130 Gas+ water Approx. 120 ø100 ■ GAS DRYER, GAS COOLER (model: ZBJ / ZBC) SPECIFICATIONS PRINCIPLE OF GAS DRYER Purge gas outlet Wet sample gas 1. Gas dryer (Semi-permeable membrane vapor phase dehumidifier) Type ZBJ02503-72P ZBJ16253-48P Application Dehumidify sample gas such as flue gas or atmospheric air Measuring components SO2, NO, CO, CO2, O2, HC, H2, etc. Operating temperature -15°C to +80°C (No freezing allowed.) Mounting angle Not restricted Working pressure -0.04MPa to +0.5MPa (at 25°C) Material Dehumidification dew point (Note) Standard flow rate Pressure resistance (at gas flow rate 1L/min) Internal volume (sample side) Mass Polypropylene, Fluororesin, Viton -10°C or lower -20°C or lower 0.5L/min. Approx. 0.8 kPa 1.0L/min. Approx. 2.8 kPa Approx. 12 cm3 Approx. 20 cm3 Approx. 50 g Approx. 400 g Header Shell Semi-permeable membrane tube Dry sample gas Purge gas inlet The Gas dryer utilizes the characteristic of the semipermeable membrane tube that a certain component in a mixed gas is permeated from its higher partial pressure to the lower one. In the figure, the sample gas containing moisture is introduced through the inlet at the left end. Through the bottom right of the figure, the purge gas having a lower pressure and less moisture than the sample gas is injected. Then, moisture is removed from the wet sample gas due to the action of the semi-permeable membrane tube and discharged through the purge gas outlet. Thus, the sample gas is dried and becomes the dry sample gas to be discharged. (Note) Dehumidification conditions; Depend on the system in application example 2 under flow rate 0.5L/min, pressure 50 kPa and ambient temperature 20 to 22°C. Dehumidification Characteristic for Gas Dryer (typical example) Pressure: 0.05 MPa Ambient temperature: 20°C to 22°C GAS DRYER Application example 1: When dry purge gas is supplied separately; Pressure gauge 10 Sample Flowmeter Dehumidification dew point (°C) 2P 0 25 JO ZB -7 03 Purge gas Purge outlet Sample gas –10 P Pump –20 8P 253-4 ZBJ16 –30 –40 0.5 1.0 1.5 Flow rate (L/min) 2.0 Gas dryer Drain separator Restrictor Drain bypass 1) The purge outlet must be open to the atmosphere. 2) Although a higher sample pressure is preferable, it should normally be 0.1 MPa at maximum and atmospheric pressure at minimum. 3) The pressure gauge, when provided, is helpful for monitoring the operational status. 4) If drain occurs due to pressurization by the pump, it should partially be bypassed with the drain separator. 5) The volume of purge gas should be 2 to 5 times as large as that of sample gas. 9 Application example 2: When all volume of sample gas is usable for purge gas; Pressure gauge 1) The purge outlet must always be open to the atmosphere. 2) A higher sample pressure is advantageous. The pressure should normally be 0.1 MPa at maximum and 0.05 MPa at minimum. If the pressure is low, an adequate dehumidification effect may not be obtainable. 3) The pressure gauge, when provided, is helpful for monitoring the operational status. 4) If drain occurs due to pressurization by the pump, it should partially be bypassed with the drain separator. Filter F Analyzer Flowmeter Purge outlet Sample gas Gas dryer Drain separator P Pump Restrictor Drain bypass Caution on Use 1. Establish the flow path so dry gas flows on the face opposite to the semi-transparent face that contact the gas to be dried as shown by the example of use. 2.Dust should be removed by installing a filter of filtration accuracy 5µm or less before the dryer. Oil mist should also be disposed before the dryer. 3.If water drops enters the semi-permeable membrane tube, only the water permeates the membrane and the salts dissolved in the water are precipitated to cause clogging. Therefore, the flow path should be designed so as not to allow entrance of water drops. 4.This dryer has a large drying capacity and can reduce humidity, but cannot maintain humidity at a constant level by the ordinary usage. For using this dryer as a humidity conditioner, the flow rate, pressure and temperature need to be kept constant. 5.This dryer is unusable for gases of alcohol, ketone, and high-concentration ammonia, and those containing steam and NO 2 more than 100 ppm. OUTLINE ( Unit : mm ) Gas dryer Purge gas inlet Coupling for ø6.35 tube ø6.35 28 Purge gas outlet Coupling for ø6.35 tube Inlet of gas to be dehumidified External cylinder tube (PP) Coupling for ø6.35 tube Dry gas outlet Coupling for ø6.35 tube 1800 1890 Coupling (fluorocarbon polymers) Model : ZBJ02503-72P Coupling (fluorocarbon polymers) A B RC1/4 ø20 RC1/4 Coupling for ø6 tube Spring pin (SUS) ø38 ø38 Cap (PP) 86 Casing (PP) ZBJ16253-24P A APPROX. 714 B APPROX. 600 MASS APPROX. 250g ZBJ16253-48P 1314 1200 355g Model Model : ZBJ16253- 24 P 48 10 2-RC1/4 2. Peltier gas cooler Model ZBC91004 ZBC92004 System 1-channel corrosion-proof type 2-channel corrosion-proof type Flow rate (max.) (For constant dehumidification) (max.) Outlet gas dew point Short-time ripple 1.5L/min Parallel piping 1.5L/min (1-channel)×2 Flow rate (max.) (For prevention of condensation) (max.) 5.0L/min (dew point 0.5°C to 10°C) Dehumidification level check function T thermocouple (built in) Series piping 3L/min 1°C to 3°C ±0.1°C Limit conditions Ambient temperature (max.) Inlet gas temperature (max.) Inlet gas dew point (max.) 10L/min (dew point 0.5°C to 10°C) 40°C 40°C 40°C Main materials of gas-contacting parts Carbon, Fluoro rubber, Fluoro resin, HDPE, PVC Enclosure material SUS430 Gas inlet/outlet Rc1/4 Working pressure (max.) 60kPa Ambient temperature 2°C to 40°C Ambient humidity (max.) 90%RH Power supply 100V10V AC, 50/60Hz Power consumption (approx.) 140VA 200VA Mass (approx.) 4kg 5kg Scope of delivery Body, spiral pulling out tool x 1 (Note) Do not use gases containing organic solvent such as toluene, xylene, etc. OUTLINE ( Unit : mm ) Electronic gas cooler 1) Model: ZBC91004 2) Model: ZBC92004 Outlet Rc1/4 Inlet Rc1/4 Inlet A Outlet A Outlet B Inlet B 41 38 OUTLET B 6-Rc1/4 INLET B mounting hole 2×5.5 238 218 41 mounting hole 4-ø5.5 Drain 5 22 27.5 240 6 OUTLET A 255 245 206 Power terminal INLET A (20) 167.4 11.4 250 238 C−C+ Power terminal 202 182 161 17 10 C−C+ 167.4 162 50 50 50 23 38 34 38 8.5 5.5 200 217 Drain A Drain B Wiring diagram For internal connection + – H T G C+ C– G V U AC100V 50/60Hz output for T thermocouple 11 ■ FLOWMETETER, REGULATOR (model: ZBD) SPECIFICATIONS 1. Pressure Regulator ZBD61003 Type Application ZBD62003 ZBD63003 Left-hand thread for pressure adjustment of standard gas For general use (note) Right-hand thread for pressure adjustment of standard gas For general use (note) ZBD64003 Right-hand thread for pressure adjustment of standard gas For corrosion prevention (note) Left-hand thread for pressure adjustment of standard gas For corrosion prevention (note) Primary pressure Max. 14.7 MPa Max. 14.7 MPa Max. 14.7 MPa Max. 14.7 MPa Secondary pressure Variable from 0 to 0.12MPa Variable from 0 to 0.12MPa Variable from 0 to 0.15MPa Variable from 0 to 0.15MPa Connection Standard gas container Standard gas container Right-hand 22/14 threads Left-hand 22/14 threads Gas outlet Rc 1/4 Gas outlet Rc 1/4 Standard gas container Standard gas container Right-hand 22/14 threads Left-hand 22/14 threads Gas outlet Rc 1/4 Gas outlet Rc 1/4 Main materials of C3604 gas-contacting parts NBR C3604 NBR SUS316 Teflon SUS316 Teflon Mass (approx.) 2.2 kg 2.2 kg 2.2 kg 2.2 kg Scope of delivery Main unit and accessory (nylon packing for standard gas connection x 3) Main unit and accessory (Teflon packing for standard gas connection x 3) Note) Thread for connection with standard gas container: Right-hand thread when the specified combustible gas concentration of standard gas is less than 5% in total, and left-hand thread when it is 5% or more. Application: For general use; for other than corrosion prevention For corrosion prevention; When the specified gas concentration of standard gas is 1% CO or more (due to corrosion prevention) or when specifying corrosion prevention 3. Relief Valve 2. Needle Valve Model ZBD23003 Application Withstanding pressure ZBD24003 ZBD25003 0.1MPa Application 1.0MPa Ambient temperature -10°C to 45°C -10°C to 60°C Rc1/4 Connection port ø6 hose port Materials of gas-contacting parts PVC Viton rubber BSBM2 SUS316 100 g 150 g 130 g Mass (approx.) Scope of delivery 40 to 60kPa Ambient temperature 0°C to 45°C Connection port Rc1/4 Materials of gas-contacting parts PVC Viton rubber Hastelloy C Mass (approx.) 200 g Main unit 5. Flow Checker ZBD5 Model ZBD4 03 For general exhaust gas (metal joint unusable) 0.49MPa Ambient temperature -10°C to 60°C Rc1/4 Connection port Mass (approx.) 12 Model ZBD71003 ZBD72003 Application Flow rate monitoring Flow rate monitoring Operating pressure Atmospheric pressure Atmospheric pressure Ambient -10°C to 60°C -10°C to 60°C temperature POM, hard glass, fluoro rubber SUS304, hard glass, fluoro rubber Connection port 6th code ( (air, atmospheric pressure, 20°C) Material of Glass SUS316 Glass SUS316 part contact- Polyethylene Polyethylene Chloroprene ing gas Chloroprene ) Flow rate scale Flow regulating needle valve 03 For dangerous gas, corrosive gas (metal joint usable) Withstanding pressure Materials of gas-contacting parts Sample gas and drain relief Settable pressure 4. Flow Meter Application ZBD35103 Model Flow rate regulation 5th code ( 100 g ) 1 : 0.1 to 1L/min 2 : 0.2 to 2L/min 3 : 0.5 to 5L/min 4 : 1 to 10L/min 5 : 2 to 20L/min 9 : As specified 2 : With needle valve (at inlet) 4 : With needle valve (at outlet){when pump is installed after it} 7 : Without needle valve 500 g ø6 hose port ø6 hose port Flow rate range White zone Yellow zone 0.3 to 0.7L/min 0.7 to 1.3L/min Mass Approx. 100 g Approx. 100 g Scope of delivery Main unit Main unit OUTLINE ( Unit : mm ) Outlet pressure indicator Inlet pressure indicator Pressure regulation handle ZBD61 Right-hand thread ZBD62 Left-hand thread W22-14 110 Stop valve handle Rc1/4 163 Cylinder packing (Dyfron) 82 OUT 173 H.P. safety valve L.P. safety valve Rc1/4 Rc1/4 12 Pressure regulator (ZBD61/ZBD62) Inlet pressure indicator Gas inlet Gas outlet ø70 83 Stop valve handle 30 Outlet pressure indicator 13 104 78 91 Max . 114 IN 158 Cylinder packing Mounting screw 2–M5 Relief valve (ZBD35) Pressure regulation handle Connecting screw W22, 14 threads ZBD63 Right-hand thread ZBD64 Left-hand thread 188 Gas outlet Rc1/4 Pressure regulator (ZBD63/ZBD64) ø22.5 panel cutout, ø24 hole 18 ø6 30 18 18 30 54 Approx. 24 ø16.5 panel cutout, ø18 hole Gas inlet Rc1/4 Gas outlet Rc1/4 ø13 Gas inlet ø22 14 ø43 18 2-ø4.5 Gas outlet Rc1/4 22 (Fully closed) Needle valve (ZBD23) 9.5 55 (Fully open) 22 12 ø43 Panel cutout 53 (Fully open) ø6 Gas outlet Panel 13 Mounting screw 2-M4 38 Needle valve (ZBD24) 40 Gas inlet Rc1/4 Needle valve (ZBD25) Rc1/4 Top Gas outlet Flow meter (ZBD44) 114 19 (with needle valve on upper) 34 31 5 Gas inlet Gas inlet ø18 Ø18 38 146 38 Mounting hole 2–ø4.5 38 Mounting direction Gas outlet Rc1/4 25 Flow meter (ZBD47) Flow meter (ZBD42) (with needle valve on lower) Panel Flow meter (ZBD57) 10 Max. Gas outlet 44 60 95 8 Gas inlet Approx. 23 (full open) Flow meter (ZBD52) 15.6 Gas inlet ø6 2–ø4.5 ø18 ø22 2–M4 Rc1/4 Mounting screw 2-M4 30 2–ø24 80 30 112 25 Gas outlet ø6 ø18 Rc1/4 Mounting direction 22 Approx. 23 (full open) 5 25 32 25 28 Top Flow meter (ZBD54) 8 8 30 24 16 Panel cutout (ZBD5) 13 ■ Ball valves and selector valves (model: ZBF) SPECIFICATIONS Kind Item Ball valve 2-way valve 4-way valve 4-way valve Model ZBFB1003 ZBFB2003 ZBFB3003 ZBFB4003 ZBFH2003 Application General ball valve Selection between sample Selection between sample Selection between sample gas and standard gas gas and standard gas gas and standard gas (for metal joint) Withstanding pressure ZBFB1, 2; 2.0MPa ZBFB3, 4; 4.0MPa 0.3MPa 0.15MPa 0.5MPa -10°C to 120°C -5°C to 45°C -10°C to 80°C Rc1/8 Rc1/8 Rc1/4 Ambient temperature -10°C to 80°C Rc1/4 ZBFH4003 ZBFH5003 Connection port ZBFB1, 3 ; ZBFB2, 4 ; Rc1/2 Materials of gas-contacting parts ZBFB1, 2 ; Brass, Teflon SUS316 ZBFB3, 4 ; SUS316, Teflon Teflon PVC Teflon SUS316 Teflon Mass (approx.) 200g 250g 500g 230g OUTLINE ( Unit : mm ) ZBFB1, 3 : 31 ZBFB2, 4 : 42 ZBFB1, 3 : 60 ZBFB2, 4 : 80 ZBFB1, 3 : Rc1/4 ZBFB2, 4 : Rc1/2 (at both inlet and outlet) ZBFB1, 3 : 19 ZBFB2, 4 : 26.5 ZBFB1, 3 : 40 ZBFB2, 4 : 54.6 Ball valve (ZBFB) 5-Rc1/4 (ZBFH5) 5-Rc1/8 (ZBFH4) M4 for removing knob 36 ø28 25 49 B Type ZBFH4 ZBFH5 Rc1/8 2-way valve (ZBFH2) 14 C 40 A B C 22 38 70 19 41 73 2-ø4.5 hole Mounting dimensions 40 ø18 ø32 Panel cutout, ø15 hole 2-M4 72 12 36 Locking pin ø3x2 M14 P=1 Handle fastening screw ø50 ø30 A Gas inlet 1 ø3 le ho 4-way valve (ZBFH4/ZBFH5) ■ GAS ASPIRATOR (model: ZBG) SPECIFICATIONS Model Materials of gas-contacting parts ZBG62004 ZBG52004 Diaphragm, valve: Viton Pump head: PP 100V±10V AC, 50/60Hz, approx. 50W Power supply ZBG80004 Diaphragm, valve: Viton Pump head: PPS 100V±10V AC, 50/60Hz, approx. 30W Max. vacuum Max. pressure (in continuous use) Approx. -59.9kPa Approx. -26.6kPa Approx. -26.6kPa Approx. 98.0kPa Approx. 29.4kPa Approx. 29.4kPa Max. EX-flow Approx. 8L/10L/min Approx. 3L/3.6L/min Approx. 2.0L/min So as to set the motor shaft horizontal Mounting 0°C to 40°C Ambient temperature Rc1/4 2.2kg Connection port Mass (approx.) GA-380VF-DA (Discrimination) Rc1/8 1.7kg GA-330V GS-3FD-F 80 −13 −27 −40 60 40 20 1 2 3 4 5 6 7 Discharge flow rate (L/min) ZBG5 50 40 OUTLET Rc 1/4 106 90 9.5 4-ø4.4 mounting hole 73 58 22 Power terminal 19.5 0 −7 −13 −20 30 20 10 1.0 2.0 3.0 Discharge flow rate (L/min) 0 ZBG6 OUTLINE ( Unit : mm ) ZBG80 INLET Rc 1/8 OUTLET Rc 1/8 120 58 113 Capacitor Nameplate 14.5 85 100 50Hz 60Hz 104 0 Suction resistance [kPa] [kPa] 12 Discharge pressure 100 [kPa] 50 Suction resistance 45 [kPa] 50Hz 0 40 60Hz 35 −13.3 30 −26.6 25 −39.9 20 15 10 5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Discharge flow rate (L/min) Discharge pressure Suction resistance 50Hz [kPa] 60Hz 0 {0} [kPa] Discharge pressure PERFORMANCE CURVE (at ambient temperature 20 ) 39 INLET Rc 1/4 UL3266AWG22 170 78 ø70 Ground terminal Mount with this surface facing down. 102 84 (7) 90 78 E 133 E 7 9 ø4-7 (Mounting hole) 4-ø4.4 4-Rubber bush (accessories) ZBG52, ZBG62 SCOPE OF DELIVERY ZBG5, 6 main unit Accessories: Diaphragm Mounting tool Rubber foot ZBG main unit Accessories: Rubber foot Usage and caution in use 1 1 4 4 Consumable parts/spare parts For ZBG5 For ZBG6 For ZBG8 Diaphragm Valve ZBG80 ZBNG1012 (set of 5), Consumption: 1 to 2 pcs./year ZBNG1022 (set of 5), Consumption: 1 to 2 pcs./year 1) Since aspiration pressure of the aspirator is large, be sure to install a safety drain trap for draining process before the aspirator to prevent drain from being sucked up. 2) The diaphragm and the valve should be replaced periodically. Be sure to allow space for the replacement above the pump head. (Space sufficient for attachment/detachment of screws with a driver, 150mm or larger, is required.) Spare parts for 1 year (For ZBG5, ZBG6, and ZBG8) ZBN3BG52: Diaphragm × 2, Valve × 1 15 ■ DRAIN TRAP/POT/SEPARATOR (model: ZBH) SPECIFICATIONS 1. Safety Drain Trap 5. Bubbler Model: ZBH51603 Suction sample gas flow rate: Max. 3L/min Working pressure: -5.78kPa Water sealing: 0.98kPa Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size:Drain inlet ;Rc 1/4 Drain outlet;Rc 1/4 Mass: Approx. 0.6 kg Model: ZBH65003 Gas outlet pressure: Approx. +3.7kPa Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size: Gas inlet/outlet Rc 1/4 Drain inlet/outlet Rc 1/4 Mass: Approx. 0.6kg 2. Drain Pot Model; Length ZBH13 03 255mm (ZBH130) 405mm (ZBH131) 650mm (ZBH133) Material: PVC (transparent) Ambient temperature: 1°C to 40°C Connection port size: Drain outlet;Rc 1/4 Inlet ;ø39 Mass: Approx. 0.8kg (ZBH130) 3. Sealed Drain Pot 0 ZBH3 03 1 0 Working pressure: 1.0 MPa (material SUS) 0.1 MPa (material PVC) Material: SUS304 or PVC (transparent) Ambient temperature : 1°C to 40°C Connection port size: Rc 1/4 Internal volume: 280 cc for material SUS 370 cc for material PVC Mass: Approx. 0.4kg (material PVC) Approx. 1.5kg (material SUS) Model: 4. Drain Separator Model: ZBH81333 (1.1m dripping tube) ZBH81533 (1.3m dripping tube) Material: PVC (self-color) Ambient temperature: 1°C to 40°C Connection port size: Gas inlet/outlet Rc 1/2 (with joint for ø10 Teflon tube) Mass: Approx. 0.8kg To analyzer Exhaust Drain discharge Bubbler ZBH65 Peltier gas cooler ZBC Usage of Bubbler 6. Tank Model: ZBH41003 Internal volume: Approx. 1.5L Material: PVC (non-transparent) Ambient temperature: 1°C to 40°C Connection port size: Rc 1/4 Mass: Approx. 0.5kg 7. Gas Conditioner Model: ZBH91003 Sample gas pressure: Approx. -3kPa to +3kPa Outlet gas pressure: Approx. +4.5kPa Materials: Main unit; PVC (transparent) Filter; Polyethylene O-ring; Chloroprene Pore size of filter:Approx. 5µm Ambient temperature: 1°C to 40°C Connection port size: Sample gas inlet ; Gas inlet/sample gas outlet ; Drain outlet ; Drain inlet ; Mass: Approx.1.5kg Rc 3/8 ø6.5mm Rc 3/8 Rc 1/4 CODE SYMBOLS (ZBH) CONSUMABLE AND SPARE PARTS 1 2 34 5678 Z BH 3 Filter element for ZBH9 ZBNH2012 (2pcs/1set) O-ring for ZBH9 ZBNN1012 (10pcs/1set) JIS G65 Spare parts for 1 year for ZBH9 ZBN3BB42 Filter × 3, O-ring × 2 Description Part name 16 Pump ZBG Application/specification 1 1 1 1 3 3 3 3 0 1 3 9 0 0 0 0 Drain pot Length 255mm Length 405mm Length 650mm Length as specified 3 3 3 3 0 0 1 1 0 9 0 9 0 0 0 0 Sealed drain pot Material SUS 304, length L = 120mm Material SUS 304, length L = as specified (within 1m) Material PVC, length L = 200 mm Material PVC, length L = as specified (within 1m) 3 5 00 Demister Drain separation, PVC 4 1 00 Tank Buffer tank for paramagnetic oxygen analyzer 5 160 5 190 Safety drain trap Length X = 590mm, Y = 120mm Length X, Y specifiable (X + Y within 800mm) 6 5 00 6 5 90 Bubbler Length L = 400mm Length L, specifiable 8 133 8 1 53 Drain separator With 1.1 m dripping tube (with joint for ø10mm tube) With 1.3 m dripping tube (with joint for ø10mm tube) 9 100 Gas conditioner Mist filter, safety drain trap and bubbler combined into integral body OUTLINE ( Unit : mm ) Drain discharge port 15 2–Rc1/4 5 Rc1/4 40 Air inlet Drain inlet Rc1/4 Rc1/4 807 10 21 L=650/ZBH133 L=by order/ZBH139 ø60 ø22 L=405/ZBH131 Drain pot (ZBH13 ) 2–Rc1/4 Safety drain trap (ZBH51) Joint (teflon) ø61 200 Sealed drain pot (ZBH30) Gas inlet 4–M4 2–Rc1/2 ø60 Rc1/4 L=200/ZBH310 L=by order/ZBH319 Rc1/4 L=120/ZBH300 L=by order/ZBH309 ø95 ø10/ø8 Teflon tube L Drain outlet 120(Y) L L=255/ZBH130 590(X) ø60 ø39 hole 35 10 10 Cartride filter 108 195 ø67 Approx. 96 Rc1/2 Approx. 34 ø22 Gas inlet ø6.5 Drain outlet ø8.5 Y=450 2–ø9 Sample gas outlet Rc 1/4 Sample gas inlet Rc 3/8 X=690 ZBH81333: Approx. 1250 ZBH81533: Approx. 1450 70 90 5 1504 1450 142 30 60 Gas outlet (ZBH31) ø48 Drain separator (ZBH81) Drain inlet ø6.5 Gas conditioner (ZBH91) Rc1/4 inlet Exhaust Gas inlet 30 ø1 14 5 80 2-Rc1/4 With 1 plug 40 Rc1/4 Transparent ø60 31 Approx. 137 Bubbler (ZBH65) L=400/ZBH650 L=by order/ZBH659 4-Rc1/4 outlet and inlet of exhaust gas from other analyzer Mounting hole 2-ø9 0 20 2-Rc1/4 Drain inlet ø8 L L+150 270 240 210 Drain outlet Tank (ZBH41) 17 ■ GAS CONVERTER (model: ZDL) SPECIFICATIONS 1. NO2/NO CONVERTER Type Mounting Target gas Catalyst Temperature controller Material of part contacting gas Exchange efficiency Gas flow rate Ambient temperature Power supply Power consumption Mass (approx.) Gas condition Overseas use 2. CO/CO2 CONVERTER ZDL03001 ZDL04001 Indoor surface mounting Exhaust gas from general boilers/ atmosphere (Contact us for applications to gases other than those.) Usage: 2cm3 Replacement cycle: About 12 months (When O2 concentration reaches 5%, NO2 concentration 10ppm and flow rate 0.3L/min.) Temperature setting: 210±10°C (Detection terminal: K thermocouple) Built in Microcontroller X (Type: PXR4) Type Mounting Target gas Catalyst Temperature controller Material of part contacting gas Exchange efficiency Ceramic, Viton, glass filter, SUS316 90% or higher, Conforming to JIS 0.5L/min -5°C to +45°C 100V AC, 50/60Hz 100 to 240V AC, 50/60Hz Approx. 85VA 1.1kg 1.2kg Gases with dust and drain removed at 150°C or lower CE mark compliant STANDARD ACCESSORIES Gas flow rate Ambient temperature Power supply Power consumption Mass Gas condition ZDL21001 Indoor surface mounting Atmosphere (Contact us for applications for other gases.) Usage: 3cm3 Replacement cycle: About 6 months (Varies depending on usage conditions.) Temperature setting: 210±20°C (Detection terminal: K thermocouple) To be installed separately Microcontroller X (Type: PXR4) SUS316, Viton, glass wool 99% or higher (100ppm CO or lower) (Standard: 99.9%) Standard: 0.5L/min. or 1L/min. -5C to +45°C 100V AC, 50/60Hz Approx. 45VA Approx. 2kg Gases with dust and drain removed at 150C or lower SPARE PARTS FOR 1-YEAR OPERATION ZDL03, 4 ZDL21 Spare part model ZBN1DL72 ZBN1DL82 ZBN1DL42 CO/CO2 catalyst (for 1 cycle) –– 1 Converter type ZDL03 ZDL04 ZDL21 Glass wool –– 1 1 2 Converter type NO2/NO catalyst 2 CO/CO2 catalyst Glass wool 1 2 2 4 Catalyst fixture Joint 18 2 1 OUTLINE ( Unit : mm ) [150] 135 148 135 124 AL2 AL3 220 7 8 SEL PXR-4 Gas inlet ø9.5/ø5.5 Approx. 130 27 (NP) 4-ø5 LNE 100V AC (shared with internal wiring) 4-ø5 Gas inlet ø9.5/5.5 Power terminal 100 to 240V AC Right side view Front view NO2/NO converter ZDL03001 NO2/NO converter ZDL04001 19 103 2.3 104 70 94 R3 ø9.5 13 Gas outlet 8 ø1 1 Connection diagram K 55 30 17 370 CO/CO2 E converter SSR 25 300 240 270 1 2 3 4 5 30 110 Gas outlet ø9.5/5.5 (212) AL1 SV (12) C2 (NP) Connection diagram 105 [120] [210] C1 PV 130 105 160 Gas outlet ø9.5/ø5.5 Temperature controller 100V AC power supply AC 32 Gas inlet CO/CO2 converter ZDL21001 19 ■ STANDARD GAS (model: ZBM) CODE SYMBOLS 1. Pure Gas in volume of 3.4 or 10Lcylinder 1 2 3 4 5 6 7 8 9 10 Z BM Y04 - Description 1 2 3 4 5 6 7 8 9 10 Z BM N 4 - Cylinder size 10L 3.4L 1 3 AY BY EY KY LY MY PY SY NY TY 0 0 0 0 0 0 0 0 0 0 4 4 4 4 4 4 4 4 4 4 - TY04 - 4 RY0 4 - 0 VY04 - 0 VY04 - 4 ZY04 - 0 1 2 3 4 Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread Export certificate None None Provided Provided GY 0 4 - 0 HY 0 4 - 0 HY 0 4 - 4 ZY04 - 0 1 2 3 4 Description Description O2 N2 (B) For general use N2 (A) Equivalent to zero gas for generation source with certification N2 (A) Zero gas for generation source with certification AIR (B) For general use AIR (A) Equivalent to zero gas for generation source with certification AIR (A) Zero gas for generation source with certification Others Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread OUTLINE ( Unit : mm ) øD L Approx. weight [kg] 10L 140 965 15 3.4L 140 425 6 øD, L Internal volume Note1) 1 2 3 4 Export certificate None None Provided Provided Cap With/without of specification None Approved class 1 standard gas for general use Approved class 2 standard gas for general use 0 1 2 Connection thread Right-hand thread Left-hand thread Right-hand thread Left-hand thread Export certificate None None Provided Provided 4. Canned Standard Gas in volume of 0.7Lcylinder Approx. 50 DY 0 4 - 4 Concentration 45 to 50ppm 90 to 100ppm 180 to 200ppm 225 to 250ppm 450 to 500ppm 900 to 1000ppm 1800 to 2000ppm 0.45% to 0.5% 0.9% to 1% 1.8% to 2% 4.5% to 5% 9% to 10% 18% to 20% 45% to 50% Other as specified A B C D E F G H J K L M N P Z 1 2 3 4 5 6 7 8 9 10 Z BM4 4 - 00 WY 0 NAG NZ Z Description Component and concentration N2 (B) CO2 1800 to 2000ppm/N2 Specified component/concentration (Contact Fuji.) Note) Canned standard gas is available in dozen (12). L QY 0 4 - 0 CY0 4 - 0 DY 0 4 - 0 Gas component and residual gas CO2 N2 CO N2 CH4 N2 H2 N2 Ar N2 He N2 NH3 N2 O2 N2 SO2 N2 NO N2 Other N2 A B E K L M P S T U Z 3. Pure Gas in volume of 47Lcylinder 1 2 3 4 5 6 7 8 9 10 Z BM2 Y 0 4 - Description Cylinder size 10L 3.4L 1 3 Component and application CO2 CO CH4 H2 Ar He NH3 O2 N2 (B) For general use N2 (A) Equivalent to zero gas for generation source with certification N2 (A) Zero gas for generation source with certification AIR (B) For general use AIR (A) Equivalent to zero gasfor generation source with certification AIR (A) Zero gas for generation source with certification Others 0 0 0 0 0 0 0 0 0 0 2. 2-Component Mixture Gas in volume of 3.4 or 10Lcylinder øD Two-component mixed gas (3.4, 10L), Deviation Gas with class 1 certification :1% of labeled value Others :2% Valid term :1 year Note2) Thread for connection (22/14 thread): Left-hand screw :lncluded 5% more combustible gas (except NH3) Right-hand screw :Other gases Caution on Safety *Before using this product, be sure to read its instruction manual in advance. International Sales Div Sales Group Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan http://www.fujielectric.com Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425 http://www.fjielectric.com/products/instruments/ Information in this catalog is subject to change without notice. Printed in Japan