Product Specification PE4270 SPST CATV UltraCMOS™ Switch DC - 3000 MHz Product Description The PE4270 is a is a high-isolation Switch designed for CATV applications, covering a broad frequency range from near DC up to 3000 MHz. This single-supply SPST switch offers a single-pin CMOS control interface with industry leading CTB performance. It also provides low insertion loss, high isolation and extremely low bias requirements while operating on a single 3-volt supply. In a typical CATV application, the PE4270 provides for a cost effective and manufacturable solution vs. mechanical relays. The PE4270 is manufactured on Peregrine’s UltraCMOS™ process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Features • Integrated 0.25 watt terminations • CTB performance of 90 dBc • High isolation: 90 dB at 5 MHz, 63 dB at 1000 MHz • Low insertion loss: 0.5 dB at 50 MHz, 0.70 dB at 1000 MHz • High input IP2: >80 dBm • CMOS/TTL single-pin control • Single +3-volt supply operation • Extremely low bias: 8 µA @ 3 V • Available in a 6-lead DFN package Figure 1. Functional Diagram Figure 2. Package Type 6-lead DFN RF1 RF2 75 CMOS Control Driver 75 CTRL Table 1. Electrical Specifications @ +25 °C (ZS = ZL = 75 Ω) Parameter Operating Frequency Condition 1 Minimum Typical DC Units 3000 MHz 0.65 0.85 dB Insertion Loss DC – 50 MHz 1000 MHz Isolation DC – 50 MHz 1000 MHz 85 60 90 63 dB Return Loss 5 - 1000 MHz, VCNTL = 3.0V 15 16 dB 1000 MHz 28 30 dBm -90 dBc 1 dB Compression 2,4 77 & 110 channels; PO = 44 dBmV CTB / CSO Input IP2 2 Input IP3 2 Video Feedthrough 0.50 0.70 Maximum 1000 MHz 80 dBm 1000 MHz 50 dBm 3 Switching Time 15 2 mVpp µS Notes: 1. Device linearity will begin to degrade below 1 MHz. 2. Measured in a 50 Ω system. 3. Measured with a 1 ns risetime, 0/3 V pulse and 500 MHz bandwidth. 4. Note Absolute Maximum ratings in Table 3. Document No. 70-0148-03 │ www.psemi.com ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8 PE4270 Product Specification Figure 3. Pin Configuration VDD 1 6 Table 4. DC Electrical Specifications RF2 Parameter Min Typ Max Unit VDD Power Supply 2.7 3.0 3.3 V 8 20 µA 0.7xVDD 5 V 0 0.3xVDD V IDD Power Supply Current GND 2 Exposed Solder Pad 5 (VDD = 3V, VCTRL = 3V) Control Voltage High GND (bottom side) Control Voltage Low 3 RF1 4 CTRL Table 5. Control Logic Truth Table Control Voltage (CTRL) Table 2. Pin Descriptions High 1 Signal Path (RF1 to RF2) ON Pin No. Pin Name 1 VDD 2 GND Ground connection. 2 3 RF1 RF port. 1 Electrostatic Discharge (ESD) Precautions 4 CTRL CMOS or TTL logic level: High = RF1 to RF2 signal path Low = RF1 isolated from RF2 5 GND Ground connection. 3 6 RF2 RF port. 1 When handling this UltraCMOS™ device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 3. Low Description Notes: 1. CTRL accepts both CMOS and TTL voltage leads. Nominal 3 V supply connection. Notes: 1. Both RF pins must be held at 0 VDC or require external DC blocking capacitors 2. The exposed pad must be soldered to the ground plane for proper switch performance. Min Max Unit Power supply voltage -0.3 4.0 V Voltage on CTRL input -0.3 5.5 V TST Storage temperature -65 150 °C TOP Operating temperature -40 85 °C PIN Input power (50 Ω), CTRL=1/CTRL=0 33/24 dBm 500 V VDD VI VESD Parameter/Condition ESD voltage (Human Body Model) Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Functional operation should be restricted to the limits in the DC Electrical Specifications table. Exposure to absolute maximum ratings for extended periods may affect device reliability. ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8 Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOS™ devices are immune to latch-up. Table 3. Absolute Maximum Ratings Symbol OFF Device Description The PE4270 high isolation SPST CATV Switch is designed to support CATV applications such as premise disconnect of a CATV signal path. This function is typically performed by bulky and expensive mechanical relays. The high isolation characteristics, high compression point, and integrated 75-ohm terminations make the PE4270 an ideal, cost effective and manufacturable product of choice. The control logic input pin (CTRL) is typically driven by a 3-volt CMOS logic level signal, and has a threshold of 50% of VDD. For flexibility to support systems that have 5-volt control logic drivers, the control logic input has been designed to handle a 5-volt logic HIGH signal. (A minimal current will be sourced out of the VDD pin when the control logic input voltage level exceeds VDD.) Document No. 70-0148-03 │ UltraCMOS™ RFIC Solutions PE4270 Product Specification Typical Performance Data @ -40 °C to 85 °C (Unless Otherwise Noted) (75 Ω impedance except as indicated) Figure 4. Insertion Loss - RF1 to RF2 Figure 5. 1dB Compression & 3rd Order Intercept Point (T = 25°C) Figure 6. Isolation - RF1 to RF2 Document No. 70-0148-03 │ www.psemi.com ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 8 PE4270 Product Specification Typical Performance Data @ -40 °C to 85 °C (Unless Otherwise Noted) (75-ohm impedance) Figure 7. RF1 Return Loss (Switch = ON) Figure 8. RF1 Return Loss (Switch = OFF) Figure 9. RF2 Return Loss (Switch = ON) Figure 10. RF2 Return Loss (Switch = OFF) ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 8 Document No. 70-0148-03 │ UltraCMOS™ RFIC Solutions PE4270 Product Specification Evaluation Kit Figure 11. Evaluation Board Layouts Peregrine Specification 101/0167 (with F connectors) The PE4270 EK board was designed to ease customer evaluation of Peregrine’s high performance SPST CATV MOSFET switch. RF1 is connected through a 75 Ω transmission line via the top left F connector, J1. RF2 is connected through a 75 Ω transmission line via the top right F connector, J2. A 75 Ω through transmission line is available via F connectors J3 and J4. This transmission line can be used to estimate the loss of the PCB over the environmental conditions being evaluated. VDD is supplied via J6-2, while the control logic voltage is supplied via J5-2. It is the responsibility of the customer to determine proper supply decoupling for their design application. It has been observed that by removing C1 and C2 from the evaluation board has not shown to degrade RF performance. The board is constructed of a two metal layer FR4 material with a total thickness of 0.031”. The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide model with trace width of 0.021”, trace gaps of 0.030”, dielectric thickness of 0.028”, metal thickness of 0.0021” and εr of 4.6. Note that the predominate mode for these transmission lines is coplanar waveguide with a ground plane. Figure 12. Evaluation Board Schematic Peregrine Specification 102/0224 Document No. 70-0148-03 │ www.psemi.com ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 8 PE4270 Product Specification Figure 13. Package Drawing 6-lead DFN -A- 3.00 6 5 CL -B4 0.125 CL 3.00 PIN MAR 1 K 0.10 C 4 1 2 3 0.10 C 4 0.125 10°+2° -10° TOP VIEW DETAIL C 0.025 ±0.025 0.100 C 0.70 ± 0.05 0.90 ±0.10 0.20 ±0.05 SEATING PLANE 0.080 C 3 SIDE VIEW SEE DETAIL B 0.025±0.025 CL +0.08 -0.02 0.10 0.05 C 0.95 0.17 MIN. 0.24 +0.20 -0.08 0.35 EXPOSED PAD 1 DETAIL B -C- 2 C A B 0.29 3 SEE DETAIL A +0.21 -0.08 0.125 EXPOSED SLUG/ HEAT SINK 0.17 0.30 R0.127 TYP R 0.15 TYP 1.21 ±0.10 0.605 ±0.05 EXPOSED (2X) 6 5 3 4 .20 MIN. THIS FEATURE APPLIES TO BOTH ENDS OF THE PKG. EXPOSED METALIZED FEATURE DETAIL A EDGE OF PLASTIC BODY 1.05±0.05 2.01±0.10 BOTTOM VIEW 1. DIMENSIONS AND TOLERANCES ARE PER ANSi Y14.5 2. DIMENSIONS ARE IN MILLIMETERS, ANGLES ARE IN DEGREES. 3 COPLANARITY APPLIES TO EXPOSED HEAT SLUG AS WELL AS THE TERMINALS. 4 PROFILE TOLERANCE APPLIES TO PLASTIC BODY ONLY. ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 8 Document No. 70-0148-03 │ UltraCMOS™ RFIC Solutions PE4270 Product Specification Figure 14. Tape and Reel Specifications 6-lead DFN Table 6. Dimensions Dimension DFN 3x3 mm Ao 3.23 ± 0.1 Bo 3.17 ± 0.1 Ko 1.37 ± 0.1 P 4 ± 0.1 W 8 +0.3, -0.1 T 0.254 ± 0.02 R7 Quantity 3000 R13 Quantity N.A. Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel Table 7. Ordering Information Order Code Part Marking Description Package Shipping Method 4270-01 4270 PE4270-06DFN 3x3mm-12800F 6-lead 3x3 mm DFN 12800 units / Canister 4270-02 4270 PE4270-06DFN 3x3mm-3000C 6-lead 3x3 mm DFN 3000 units / T&R 4270-00 PE4270-EK PE4270-06DFN 3x3mm-EK Evaluation Kit 1 / Box 4270-51 4270 PE4270G-06DFN 3x3mm-12800F Green 6-lead 3x3 mm DFN 12800 units / Canister 4270-52 4270 PE4270G-06DFN 3x3mm-3000C Green 6-lead 3x3 mm DFN 3000 units / T&R Document No. 70-0148-03 │ www.psemi.com ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 8 PE4270 Product Specification Sales Offices The Americas North Asia Pacific Peregrine Semiconductor Corp. Peregrine Semiconductor K.K. 9450 Carroll Park Drive San Diego, CA 92121 Tel 858-731-9400 Fax 858-731-9499 5A-5, 5F Imperial Tower 1-1-1 Uchisaiwaicho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Commercial Products: Bâtiment Maine 13-15 rue des Quatre Vents F- 92380 Garches, France Tel: +33-1-47-41-91-73 Fax : +33-1-47-41-91-73 Space and Defense Products: 180 Rue Jean de Guiramand 13852 Aix-En-Provence cedex 3, France Tel: +33(0) 4 4239 3361 Fax: +33(0) 4 4239 7227 South Asia Pacific Peregrine Semiconductor 28G, Times Square, No. 500 Zhangyang Road, Shanghai, 200122, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). ©2005 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 8 The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user’s own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS is a trademark of Peregrine Semiconductor Corp. Document No. 70-0148-03 │ UltraCMOS™ RFIC Solutions