TUSB9260 USB 3.0 TO SATA BRIDGE Data Manual PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Literature Number: SLLS962C December 2009 – Revised July 2010 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 www.ti.com Contents 7 ................................................................................................................ 5 1.1 TUSB9260 Features ........................................................................................................ 5 1.2 Target Applications ......................................................................................................... 5 INTRODUCTION .................................................................................................................. 6 2.1 System Overview ........................................................................................................... 6 2.2 Device Block Diagram ...................................................................................................... 6 OPERATION ....................................................................................................................... 8 3.1 General Functionality ....................................................................................................... 8 3.2 Firmware Support ........................................................................................................... 9 3.3 GPIO/PWM LED Designations ............................................................................................ 9 3.4 Power Up and Reset Sequence ......................................................................................... 10 SIGNAL DESCRIPTIONS ..................................................................................................... 11 CLOCK CONNECTIONS ...................................................................................................... 15 5.1 Clock Source Requirements ............................................................................................. 15 5.2 Clock Source Selection Guide ........................................................................................... 15 5.3 Oscillator .................................................................................................................... 16 5.4 Crystal ....................................................................................................................... 16 ELECTRICAL SPECIFICATIONS .......................................................................................... 17 6.1 Absolute Maximum Ratings .............................................................................................. 17 6.2 Recommended Operating Conditions .................................................................................. 17 6.3 DC Electrical Characteristics for 3.3-V Digital I/O ..................................................................... 17 POWER CONSUMPTION ..................................................................................................... 18 2 Contents 1 2 3 4 5 6 MAIN FEATURES Copyright © 2009–2010, Texas Instruments Incorporated TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 List of Figures 2-1 Device Block Diagram ............................................................................................................. 7 5-1 Typical Crystal Connections .................................................................................................... 15 Copyright © 2009–2010, Texas Instruments Incorporated List of Figures 3 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 www.ti.com List of Tables 3-1 GPIO/PWM LED Designations ................................................................................................... 9 4-1 I/O Definitions ..................................................................................................................... 11 4-2 Clock and Reset Signals ........................................................................................................ 11 4-3 SATA Interface Signals .......................................................................................................... 11 4-4 USB Interface Signals ........................................................................................................... 12 4-5 Serial Peripheral Interface (SPI) Signals ...................................................................................... 12 4-6 JTAG, GPIO, and PWM Signals 4-7 5-1 5-2 7-1 7-2 4 ............................................................................................... Power and Ground Signals ..................................................................................................... Oscillator Specification .......................................................................................................... Crystal Specification ............................................................................................................. SuperSpeed USB Power Consumption ....................................................................................... High Speed USB Power Consumption ........................................................................................ List of Tables 13 14 16 16 18 18 Copyright © 2009–2010, Texas Instruments Incorporated TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 USB 3.0 TO SATA BRIDGE Check for Samples: TUSB9260 1 MAIN FEATURES 1.1 TUSB9260 Features • Universal Serial Bus (USB) – SuperSpeed USB 3.0 Compliant - TID 340000007 • Integrated Transceiver Supports SS/HS/FS Signaling – Best in Class Adaptive Equalizer • Allows for Greater Jitter Tolerance in the Receiver – USB Class Support • USB Attached SCSI Protocol (UASP) • USB Mass Storage Class Bulk-Only Transport (BOT) • Support for Error Conditions Per the 13 Cases (Defined in the BOT Specification) • USB Bootability Support • USB Human Interface Device (HID) – Supports Firmware Update Via USB, Using a TI Provided Application • SATA Interface – Serial ATA Specification Revision 2.6 • gen1i, gen1m, gen2i, and gen2m – Support for Mass-Storage Devices Compatible With the ATA/ATAPI-8 Specification • Integrated ARM Cortex M3 Core – Customizable Application Code Loaded From EEPROM Via SPI Interface – Two Additional SPI Port Chip Selects for Peripheral Connection – Up to 12 GPIOs for End-User Configuration • 2 GPIOs Have PWM Functionality for LED Blink Speed Control – Serial Communications Interface for Debug (UART) • General Features – Can Operate from Either a Single Low Cost Crystal or Clock Oscillator • Supports 40 MHz – A JTAG Interface is Used for IEEE1149.1 and IEEE1149.6 Boundary Scan – Available in a Fully RoHS Compliant Package 1 1.2 • • • • Target Applications External HDD/SSD External DVD External CD HDD-Based Portable Media Player 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009–2010, Texas Instruments Incorporated TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 2 INTRODUCTION 2.1 System Overview www.ti.com The TUSB9260 is an ARM cortex M3 microcontroller based USB 3.0 to serial ATA bridge. It provides the necessary hardware and firmware to implement a USB attached SCSI protocol (UASP) compliant mass storage device suitable for bridging hard disk drives (HDD), solid state disk drives (SSD), optical drives and other compatible SATA 1.5-Gbps or SATA 3.0-Gbps devices to a USB 3.0 bus. In addition to UASP support, the firmware implements the mass storage class bulk-only transport (BOT), and USB human in-terface device (HID) interfaces. USB 3.0 (1) SuperSpeed PC with USB 3.0 Support SATA Gen1/2 HDD USB 2.0 (1) High-speed TUSB9260 (1) 2.2 USB connection is made at either SuperSpeed or High-Speed depending on the upstream connection support. Device Block Diagram The major functional blocks are as follows: • Cortex M3 microcontroller subsystem including the following peripherals: – Time interrupt modules, including watchdog timer – Universal asynchronous receive/transmit (SCI) – Serial peripheral interface (SPI) – General purpose input/output (GPIO) – PWM for support of PWM outputs (PWM) • USB 3.0 core (endpoint controller) and integrated SuperSpeed PHY • AHCI compliant SATA controller and integrated SATA PHY – Supporting gen1i, gen1m, gen2i, and gen2m • Chip level clock generation and distribution • Support for JTAG 1149.1 and 1149.6 6 INTRODUCTION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 GRSTz ROM ARM Cortex M3 VDD3.3 VDD1.8 RAM Power and Reset Distribution TCK TMS TDO TDI TRST JTAG VDD1.1 Data Path RAM 80 kB XI Clock Generation XO USB 3.0 Device Controller SATA AHCI Timer Watchdog Timer USB_R1RTN USB_R1 DP/DM USB HS/FS PHY VBUS SSRX+ SSRX- USB SS PHY SSTX+ SSTX- SATARX+ SATARX- GPIO[11:0] SATA II PHY SATATX+ SATATX- SPI PWM[1:0] GPIO PWM SCLK DATA_OUT DATA_IN CS[2:0] UartRX UarTX SCI (UART) Figure 2-1. Device Block Diagram INTRODUCTION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 7 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 3 OPERATION 3.1 General Functionality www.ti.com The TUSB9260 ROM contains boot code that executes after a global reset which performs the initial con-figuration required to load a firmware image from an attached SPI flash memory to local RAM. In the ab-sence of an attached SPI flash memory or a valid image in the SPI flash memory, the firmware will idle and wait for a connection from a USB host through its HID interface which is also configured from the boot code. The latter can be accomplished using a custom application or driver to load the firmware from a file resident on the host system. Once the firmware is loaded it configures the SATA advanced host controller interface host bus adapter (AHCI) and the USB device controller. In addition, the configuration of the AHCI includes a port reset which initiates an out of band (OOB) TX sequence from the AHCI link layer to determine if a device is connected, and if so negotiate the connection speed with the device (3.0 Gbps or 1.5 Gbps). The configuration of the USB device controller includes creation of the descriptors and configuration of the device endpoints for support of UASP and USB mass storage class bulk-only transport (BOT). In addition, the firmware provides any other custom configuration required for application specific implementation, for example a HID interface for user initiated backup. After USB device controller configuration is complete, if a SATA device was detected during the AHCI con-figuration the firmware connects the device to the USB bus when VBUS is detected. According to the USB 3.0 specification, the TUSB9260 will initially try to connect at SuperSpeed, if successful it will enter U0; otherwise, after the training time out it will enable the DP pull up and connect as a USB 2.0 high-speed or full-speed device depending on the speed supported by host or hub port. When connected, the firmware presents the BOT interface as the primary interface and the UASP inter-face as the secondary interface. If the host stack is UASP aware, it can enable the UASP interface using a SET_INTERFACE request for alternate interface 1. Following speed negotiation, the device should transmit a device to host (D2H) FIS with the device signature. This first D2H FIS is received by the link layer and copied to the port signature register. When firmware is notified of the device connection it queries the device for capabilities using the IDENTIFY DEVICE command. Firmware then configures the device as appropriate for its interface and features supported, for example an HDD that supports native command queuing (NCQ). The configuration of the USB device controller includes creation of the descriptors, configuration of the device endpoints for support of UASP and USB mass storage class bulk-only transport (BOT), allocation of memory for the transmit request blocks (TRBs), and creation of the TRBs necessary to transmit and receive packet data over the USB. In addition, the firmware provides any other custom configuration required for application specific implementation, for example a HID interface for user initiated backup. After USB device controller configuration is complete, if a SATA device was detected during the AHCI configuration the firmware connects the device to the USB bus when VBUS is detected. According to the USB 3.0 specification, the TUSB9260 will initially try to connect at SuperSpeed, if successful it will enter U0; otherwise, after the training time out it will enable the DP pull up and connect as a USB 2.0 high-speed or full-speed device depending on the speed supported by host or hub port. When connected as a SuperSpeed device, the firmware presents the UASP interface as the primary interface, and the BOT interface as a secondary interface. If the host stack is not UASP aware, it can enable the BOT interface using a SET_INTERFACE request for alternate interface 1. 8 OPERATION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com 3.2 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 Firmware Support Default firmware support is provided for the following: • USB 3.0 SuperSpeed and USB 2.0 High-Speed and Full-Speed • USB Attached SCSI Protocol (UASP) • USB Mass Storage Class (MSC) Bulk-Only Transport (BOT) – Including the 13 Error Cases • USB Mass Storage Specification for Bootability • USB Device Class Definition for Human Interface Devices (HID) – Firmware Update and Custom Functionality (e.g. One-Touch Backup) • Serial ATA Advanced Host Controller Interface (AHCI) • General Purpose Input/Output (GPIO) – LED Control and Custom Functions (e.g. One-Touch Backup Control) • Pulse Width Modulation (PWM) – LED Dimming Control • Serial Peripheral Interface (SPI) – Firmware storage and storing Custom Device Descriptors • Serial Communications Interface (SCI) – Debug Output Only 3.3 GPIO/PWM LED Designations The default firmware provided by TI drives the GPIO and PWM outputs as listed in the table below. Table 3-1. GPIO/PWM LED Designations GPIO0 SW heartbeat 00: U3 state or default 01: U2 state GPIO1/GPIO5 USB3 power state (U0-U3) GPIO2 HS/FS suspend GPIO3 Push button input on customer board GPIO4 Not used GPIO6 FS/HS connected GPIO7 SS connected PWM0 Disk activity PWM1 U3 or HS/FS suspend state (fades high and low) GPIO10 (SPICS1) Not used GPIO11 (SPICS2) Not used 10: U1 state 11: U0 state The LED’s on the TUSB9260 Product Development Kit (PDK) board are connected as in the table above. Please see the TUSB9260 PDK Guide (SLLA303) for more information on GPIO LED connection and usage. This EVM is available for purchase, contact TI for ordering information. OPERATION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 9 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 3.4 www.ti.com Power Up and Reset Sequence The TUSB9260 does not have specific power sequencing requirements with respect to the core power (VDD), I/O power (VDD33), or analog power (VDDA11, VDDA33, VDDA18, and VDDR18). The core power (VDD) or IO power (VDD33) may be powered up for an indefinite period of time while others are not powered up if all of these constraints are met: • All maximum ratings and recommended operating conditions are observed. • All warnings about exposure to maximum rated and recommended conditions are observed, par-ticularly junction temperature. These apply to power transitions as well as normal operation. • Bus contention while VDD33 is powered up must be limited to 100 hours over the projected life-time of the device. • Bus contention while VDD33 is powered down may violate the absolute maximum ratings. A supply bus is powered up when the voltage is within the recommended operating range. It is powered down when it is below that range, either stable or in transition. A minimum reset duration of 1 ms is required. This is defined as the time when the power supplies are in the recommended operating range to the de-assertion of GRSTz. 10 OPERATION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com 4 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 SIGNAL DESCRIPTIONS Table 4-1. I/O Definitions I/O TYPE DESCRIPTION I Input O Output I/O Input - Output PU Internal pull-up resistor PD Internal pull-down resistor PWR Power signal Table 4-2. Clock and Reset Signals TERMINAL NAME PIN NO. I/O DESCRIPTION GRSTz 4 I PU Global power reset. This reset brings all of the TUSB9260 internal registers to their default states. When GRSTz is asserted, the device is completely nonfunctional. XI 52 I Crystal input. This terminal is the crystal input for the internal oscillator. The input may alternately be driven by the output of an external oscillator. When using a crystal a 1-MΩ feedback resistor is required between X1 and XO. XO 54 O Crystal output. This terminal is the crystal output for the internal oscillator. If XI is driven by an external oscillator this pin may be left unconnected. When using a crystal a 1-MΩ feedback resistor is required between X1 and XO. Frequency select. These terminals indicate the oscillator input frequency and are used to configure the correct PLL multiplier. The field encoding is as follows: FREQSEL[1:0] 31, 30 I PU FREQSEL[1] FREQSEL[0] INPUT CLOCK FREQUENCY 0 0 Reserved 0 1 Reserved 1 0 Reserved 1 1 40 MHz Table 4-3. SATA Interface Signals TERMINAL PIN NO. I/O SATA_TXP 57 O Serial ATA transmitter differential pair (positive) SATA_TXM 56 O Serial ATA transmitter differential pair (negative) SATA_RXP 60 I Serial ATA receiver differential pair (positive) SATA_RXM 59 I Serial ATA receiver differential pair (negative) NAME DESCRIPTION SIGNAL DESCRIPTIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 11 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 www.ti.com Table 4-4. USB Interface Signals TERMINAL PIN NO. I/O USB_SSTXP 43 O USB SuperSpeed transmitter differential pair (positive) USB_SSTXM 42 O USB SuperSpeed transmitter differential pair (negative) USB_SSRXP 46 I USB SuperSpeed receiver differential pair (positive) USB_SSRXM 45 I USB SuperSpeed receiver differential pair (negative) USB_DP 36 I/O USB High-speed differential transceiver (positive) USB_DM 35 I/O USB High-speed differential transceiver (negative) USB_VBUS 33 I USB bus power USB_R1 39 O Precision resistor reference. A 10-kΩ ±1% resistor should be connected between R1 and R1RTN. USB_R1RTN 40 I Precision resistor reference return NAME DESCRIPTION Table 4-5. Serial Peripheral Interface (SPI) Signals TERMINAL NAME PIN NO. I/O DESCRIPTION SPI_SCLK 17 O PU SPI clock SPI_DATA_IN 18 I PU SPI master data in SPI_DATA_OUT 20 O PU SPI master data out SPI_CS0 21 O PU Primary SPI chip select for Flash RAM 23 I/O PU SPCI chip select for additional peripherals. When not used for SPI chip select this pin may be used as general purpose I/O. 22 I/O PU SPCI chip select for additional peripherals. When not used for SPI chip select this pin may be used as general purpose I/O. SPI_CS2/ GPIO11 SPI_CS1/ GPIO10 12 SIGNAL DESCRIPTIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 Table 4-6. JTAG, GPIO, and PWM Signals TERMINAL NAME PIN NO. I/O DESCRIPTION JTAG_TCK 25 I PD JTAG test clock JTAG_TDI 26 I PU JTAG test data in JTAG_TDO 27 O PD JTAG test data out JTAG_TMS 28 I PU JTAG test mode select JTAG_TRSTz 29 I PD JTAG test reset GPIO9/UART_TX 6 I/O PU GPIO/UART transmitter. This terminal can be configured as a GPIO or as the transmitter for a UART channel. This pin defaults to a general purpose output. GPIO8/UART_RX 5 I/O PU GPIO/UART receiver. This terminal can be configured as a GPIO or as the receiver for a UART channel. This pin defaults to a general purpose output. GPIO7 16 I/O PD GPIO6 15 I/O PD GPIO5 14 I/O PD GPIO4 13 I/O PD GPIO3 11 I/O PD GPIO2 10 I/O PD GPIO1 9 I/O PD GPIO0 8 I/O PD PWM0 2 O PD (1) PWM1 3 O PD (1) (1) Configurable as general purpose input/outputs Pulse Width Modulation (PWM). Can be used to drive status LED's. PWM pull down resistors are disabled by default. A firmware modification is required to turn them on. All other internal pull up/down resistors are enabled by default. SIGNAL DESCRIPTIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 13 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 www.ti.com Table 4-7. Power and Ground Signals TERMINAL PIN NO. I/O VDDR18 48, 62 PWR 1.8-V power rail VDDA18 37 PWR 1.8-V analog power rail VDD 1, 12, 19, 32, 38, 41, 44, 47, 49, 55, 58, 61, 63, 64 PWR 1.1-V power rail VDD33 7, 24, 50, 51 PWR 3.3-V power rail VDDA33 34 PWR 3.3-V analog power rail VSSOSC 53 PWR Oscillator ground. If using a crystal, this should not be connected to PCB ground plane. If using an oscillator, this should be connected to PCB ground. See the Clock Source Requirements section for more details. VSS 65 PWR Ground - Thermal Pad NAME 14 DESCRIPTION SIGNAL DESCRIPTIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 5 CLOCK CONNECTIONS 5.1 Clock Source Requirements The TUSB9260 supports an external oscillator source or a crystal unit. If a clock is provided to XI instead of a crystal, XO is left open and VSSOSC should be connected to the PCB ground plane. Otherwise, if a crystal is used, the connection needs to follow the guidelines below. Since XI and XO are coupled to other leads and supplies on the PCB, it is important to keep them as short as possible and away from any switching leads. It is also recommended to minimize the capacitance be-tween XI and XO. This can be accomplished by connecting the VSSOSC lead to the two external capaci-tors CL1 and CL2 and shielding them with the clean ground lines. The VSSOSC should not be connected to PCB ground when using a crystal. Load capacitance (Cload) of the crystal varying with the crystal vendors is the total capacitance value of the entire oscillation circuit system as seen from the crystal. It includes two external capacitors CL1 and CL2 in Figure 5-1. The trace length between the decoupling capacitors and the corresponding power pins on the TUSB9260 needs to be minimized. It is also recommended that the trace length from the capacitor pad to the power or ground plane be minimized. Figure 5-1. Typical Crystal Connections 5.2 Clock Source Selection Guide Reference clock jitter is an important parameter. Jitter on the reference clock will degrade both the trans-mit eye and receiver jitter tolerance no matter how clean the rest of the PLL is, thereby impairing system performance. Additionally, a particularly jittery reference clock may interfere with PLL lock detection mechanism, forcing the Lock Detector to issue an Unlock signal. A good quality, low jitter reference clock is required to achieve compliance with supported USB3.0 standards. For example, USB3.0 specification requires the random jitter (RJ) component of either RX or TX to be 2.42 ps (random phase jitter calculated after applying jitter transfer function - JTF). As the PLL typically has a number of additional jitter compo-nents, the Reference Clock jitter must be considerably below the overall jitter budget. CLOCK CONNECTIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 15 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 5.3 www.ti.com Oscillator XI should be tied to the 1.8-V clock source and XO should be left floating. VSSOSC should be connected to the PCB ground plane. A 40-MHz clock can be used. Table 5-1. Oscillator Specification PARAMETER CXI XI input capacitance VIL Low-level input voltage VIH High-level input voltage Ttosc_i Frequency tolerance Tduty Duty cycle TR/TF Rise/Fall time RJ Reference clock RJ TJ Reference clock TJ Tp-p Reference clock jitter (1) (2) (3) (4) CONDITIONS MIN TYP VDDIO = 1.8 V, TJ = 25°C MAX UNIT 0.414 pF 0.35 x VDDR18 V 50 ppm 55 % 20% - 80 % 6 ns JTF (1 sigma) (1) (2) 0.8 ps JTF (total p-p) (2) (3) 25 ps (absolute p-p) (4) 50 ps 0.65 x VDDR18 Operational temperature V –50 45 50 Sigma value assuming Gaussian distribution After application of JTF Calculated as 14.1 x RJ + DJ Absolute phase jitter (p-p) 5.4 Crystal A parallel, 20-pF load capacitor should be used if a crystal source is used. VSSOSC should not be connected to the PCB ground plane. A 40-MHz crystal can be used. Table 5-2. Crystal Specification PARAMETER Ttosc_i Frequency tolerance Frequency stability CL 16 CONDITIONS MIN MAX UNIT Operational temperature –50 50 ppm 1 year aging –50 50 ppm 24 pF Load capacitance 12 CLOCK CONNECTIONS TYP 20 Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 TUSB9260 www.ti.com SLLS962C – DECEMBER 2009 – REVISED JULY 2010 6 ELECTRICAL SPECIFICATIONS 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) VALUE UNIT VDDR18/ VDDA18 Steady-state supply voltage –0.3 to 2.45 V VDD Steady-state supply voltage –0.3 to 1.4 V VDD33/ VDDA33 Steady-state supply voltage –0.3 to 3.8 V 6.2 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT 1.71 1.8 1.89 V Analog 1.8 supply voltage 1.62 1.8 1.89 V Digital 1.1 supply voltage 1.045 1.1 1.155 V VDD33 Digital 3.3 supply voltage 3 3.3 3.6 V VDDA33 Analog 3.3 supply voltage 3 3.3 3.6 V VBUS Voltage at VBUS PAD 0 1.155 V TA Operating free-air temperature range 0 70 °C TJ Operating junction temperature range 0 105 °C HBM ESD 1000 V CDM ESD 500 V VDDR18 Digital 1.8 supply voltage VDDA18 VDD 6.3 DC Electrical Characteristics for 3.3-V Digital I/O over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DRIVER TR Rise time 5 pF 1.5 TF Fall time 5 pF 1.53 IOL Low-level output current VDD33 = 3.3 V, TJ = 25°C 6 IOH High-level output current VDD33 = 3.3 V, TJ = 25°C –6 VOL Low-level output voltage IOL = 2 mA VOH High-level output voltage IOL = –2 mA VO Output voltage ns ns mA mA 0.4 2.4 V V 0 VDD33 V RECEIVER VI Input voltage 0 VDD33 V VIL Low-level input voltage 0 0.8 V VIH High-level input voltage Vhys Input hysteresis tT Input transition time (TR and TF) II Input current VI = 0 V to VDD33 CI Input capacitance VDD33 = 3.3 V, TJ = 25°C 2 V 200 mV 10 ns 12 µA 0.384 ELECTRICAL SPECIFICATIONS Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 pF 17 TUSB9260 SLLS962C – DECEMBER 2009 – REVISED JULY 2010 7 www.ti.com POWER CONSUMPTION All transfers are to a SATA Gen II SSD. A SATA Gen I target yields an approximate 10-mA power savings on the 1.1-V rail. Table 7-1. SuperSpeed USB Power Consumption POWER RAIL TYPICAL ACTIVE CURRENT (mA) (1) TYPICAL IDLE CURRENT (mA) (2) VDD11 (3) 319 308 VDD18 (4) 58 58 6 6 VDD33 (1) (2) (3) (4) (5) (5) Transferring data via SS USB to a SSD SATA Gen II device. No SATA power management, U0 only. SATA Gen II SSD attached no active transfer. No SATA power management, U0 only. All 1.1-V power rails connected together. All 1.8-V power rails connected together. All 3.3-V power rails connected together. Table 7-2. High Speed USB Power Consumption (1) (2) (3) (4) (5) 18 POWER RAIL TYPICAL ACTIVE CURRENT (mA) (1) TYPICAL IDLE CURRENT (mA) (2) VDD11 (3) 197 193 VDD18 (4) 45 36 VDD33 (5) 14 14 Transferring data via HS USB to a SSD SATA Gen II device. No SATA power management. SATA Gen II SSD attached no active transfer. No SATA power management. All 1.1-V power rails connected together. All 1.8-V power rails connected together. All 3.3-V power rails connected together. POWER CONSUMPTION Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TUSB9260 PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) TUSB9260PAP PREVIEW HTQFP PAP 64 160 TBD TUSB9260PVP ACTIVE HTQFP PVP 64 250 Green (RoHS & no Sb/Br) Lead/ Ball Finish Call TI MSL Peak Temp (3) Samples (Requires Login) Call TI CU NIPDAUAGLevel-4-260C-72 HR Samples Not Available Purchase Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated