60W Single Output Industrial DIN Rail Power Supply MDR-60 series Features : Universal AC input/Full range Protections: Short circuit / Overload / Over voltage Cooling by free air convection Can be installed on DIN rail TS-35/7.5 or 15 NEC class 2 / LPS compliant (24V,48V only) LED indicator for power on DC OK relay contact No load power consumption<0.75W 100% full load burn-in test 3 years warranty SPECIFICATION MODEL MDR-60-5 MDR-60-12 MDR-60-24 MDR-60-48 DC VOLTAGE 5V 12V 24V 48V RATED CURRENT 10A 5A 2.5A 1.25A CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~ 2.5A 0 ~ 1.25A RATED POWER 50W RIPPLE & NOISE (max.) Note.2 80mVp-p OUTPUT 12 ~ 15V 24 ~ 30V 2.0% 1.0% 1.0% 1.0% LINE REGULATION 1.0% 1.0% 1.0% 1.0% LOAD REGULATION 1.5% 1.0% 1.0% 1.0% Note.5 500ms, 30ms/230VAC HOLD UP TIME (Typ.) 50ms/230VAC VOLTAGE RANGE 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz 78% 1.8A/115VAC 1A/230VAC COLD START 30A/115VAC 60A/230VAC <1mA / 240VAC OVER VOLTAGE FUNCTION DC OK SIGNAL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY OTHERS 86% 88% 87% 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 6.25 ~ 7.25V 15.6 ~ 18V 31.2 ~ 36V 57.6 ~ 64.8V Protection type : Shut down o/p voltage, re-power on to recover Relay contact rating(max.): 30V/1A resistive -20 ~ +70 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 0.03%/ (0 ~ 50 Component : 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-6 UL508, UL60950-1, TUV EN60950-1 approved, NEC class 2 / LPS compliant (24V,48V only) EMS IMMUNITY Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, ENV50204, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A MTBF 299.2K hrs min. MIL-HDBK-217F (25 40*90*100mm (W*H*D) 0.33Kg; 42pcs/14.8Kg/0.82CUFT I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:>100M Ohms/500VDC 25 70%RH ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B Compliance to EN61000-3-2,-3 HARMONIC CURRENT DIMENSION PACKING NOTE 20ms/115VAC at full load 120 ~ 370VDC AC CURRENT (Typ.) INRUSH CURRENT (Typ.) PROTECTION (Note 4) 500ms, 30ms/115VAC at full load EFFICIENCY (Typ.) OVERLOAD EMC 60W 200mVp-p 48 ~ 56V 5 ~ 6V VOLTAGE ADJ. RANGE LEAKAGE CURRENT SAFETY & 60W 150mVp-p VOLTAGE TOLERANCE Note.3 SETUP, RISE TIME INPUT 60W 120mVp-p ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:MDR-60-SPEC 2008-03-10 MDR-60 60W Single Output Industrial DIN Rail Power Supply Mechanical Specification Case No.962A 35 40 series Unit:mm 100 5 5 5 5 5 +V +V -V -V DC OK DC OK + 90 +V ADJ N L 7.5 7.5 Install DIN rail TS35/7.5 or TS35/15 Block Diagram fosc : 60KHz DC OK RECTIFIERS & FILTER EMI FILTER I/P RECTIFIERS & FILTER POWER SWITCHING +V -V O.C.P. DETECTION CIRCUIT CONTROL O.L.P. O.V.P. DC OK Relay Contact Contact Close When the output voltage reaches the adjusted output voltage. Contact Open When the output voltage drop below 90% output voltage. Contact Ratings (max.) 30V/1A resistive load Derating Curve Output Derating VS Input Voltage Ta=25 100 100 12V,24V,48V 90 80 80 70 50 5V LOAD (%) LOAD (%) 60 40 20 -20 0 10 20 30 45 55 AMBIENT TEMPERATURE ( ) 60 70 (VERTICAL) 60 50 40 85 95 100 115 120 140 160 180 200 220 240 264 INPUT VOLTAGE (VAC) 60Hz File Name:MDR-60-SPEC 2008-03-10