TI LM3914VX

LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
LM3914 Dot/Bar Display Driver
Check for Samples: LM3914
FEATURES
1
•
•
2
•
•
•
•
•
•
•
•
•
•
Drives LEDs, LCDs or Vacuum Fluorescents
Bar or Dot Display Mode Externally Selectable
by User
Expandable to Displays of 100 Steps
Internal Voltage Reference from 1.2V to 12V
Operates with Single Supply of Less than 3V
Inputs Operate Down to Ground
Output Current Programmable from 2 mA to 30
mA
No Multiplex Switching or Interaction Between
Outputs
Input Withstands ±35V without Damage or
False Outputs
LED Driver Outputs are Current Regulated,
Open-collectors
Outputs can Interface with TTL or CMOS Logic
The Internal 10-step Divider is Floating and
can be Referenced to a Wide Range of
Voltages
DESCRIPTION
The LM3914 is a monolithic integrated circuit that
senses analog voltage levels and drives 10 LEDs,
providing a linear analog display. A single pin
changes the display from a moving dot to a bar
graph. Current drive to the LEDs is regulated and
programmable, eliminating the need for resistors.
This feature is one that allows operation of the whole
system from less than 3V.
The circuit contains its own adjustable reference and
accurate 10-step voltage divider. The low-bias-current
input buffer accepts signals down to ground, or V−,
yet needs no protection against inputs of 35V above
or below ground. The buffer drives 10 individual
comparators referenced to the precision divider.
Indication non-linearity can thus be held typically to
½%, even over a wide temperature range.
Versatility was designed into the LM3914 so that
controller, visual alarm, and expanded scale functions
are easily added on to the display system. The circuit
can drive LEDs of many colors, or low-current
incandescent lamps. Many LM3914s can be
“chained” to form displays of 20 to over 100
segments. Both ends of the voltage divider are
externally available so that 2 drivers can be made
into a zero-center meter.
The LM3914 is very easy to apply as an analog
meter circuit. A 1.2V full-scale meter requires only 1
resistor and a single 3V to 15V supply in addition to
the 10 display LEDs. If the 1 resistor is a pot, it
becomes the LED brightness control. The simplified
block diagram illustrates this extremely simple
external circuitry.
When in the dot mode, there is a small amount of
overlap or “fade” (about 1 mV) between segments.
This assures that at no time will all LEDs be “OFF”,
and thus any ambiguous display is avoided. Various
novel displays are possible.
Much of the display flexibility derives from the fact
that all outputs are individual, DC regulated currents.
Various effects can be achieved by modulating these
currents. The individual outputs can drive a transistor
as well as a LED at the same time, so controller
functions including “staging” control can be
performed. The LM3914 can also act as a
programmer, or sequencer.
The LM3914 is rated for operation from 0°C to +70°C.
The LM3914N-1 is available in an 18-lead PDIP
(NFK) package.
The following typical application illustrates adjusting
of the reference to a desired value, and proper
grounding for accurate operation, and avoiding
oscillations.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
TYPICAL APPLICATIONS
Note: Grounding method is typical of all uses. The 2.2μF tantalum or 10 μF aluminum electrolytic capacitor is needed
if leads to the LED supply are 6″ or longer.
Figure 1. 0V to 5V Bar Graph Meter
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1) (2)
Power Dissipation
PDIP (NFK)
(3)
1365 mW
Supply Voltage
25V
Voltage on Output Drivers
Input Signal Overvoltage
25V
(4)
±35V
Divider Voltage
−100 mV to V+
Reference Load Current
10 mA
Storage Temperature Range
−55°C to +150°C
Soldering Information
PDIP Package
Soldering (10 seconds)
260°C
PLCC Package
Vapor Phase (60 seconds)
215°C
Infrared (15 seconds)
220°C
See http://www.ti.com for other methods of soldering surface mount devices.
(1)
(2)
(3)
(4)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication
of device performance.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The maximum junction temperature of the LM3914 is 100°C. Devices must be derated for operation at elevated temperatures. Junction
to ambient thermal resistance is 55°C/W for the PDIP (NFK package).
Pin 5 input current must be limited to ±3mA. The addition of a 39k resistor in series with pin 5 allows ±100V signals without damage.
ELECTRICAL CHARACTERISTICS (1) (2)
Parameter
Conditions
(1)
Min
Typ
Max
Units
COMPARATOR
Offset Voltage, Buffer and First
Comparator
0V ≤ VRLO = VRHI ≤ 12V,
ILED = 1 mA
3
10
mV
Offset Voltage, Buffer and Any Other
Comparator
0V ≤ VRLO = VRHI ≤ 12V,
ILED = 1 mA
3
15
mV
Gain (ΔILED/ΔVIN)
IL(REF) = 2 mA, ILED = 10 mA
Input Bias Current (at Pin 5)
0V ≤ VIN ≤ V+ − 1.5V
Input Signal Overvoltage
No Change in Display
3
8
25
mA/mV
100
nA
35
V
12
17
kΩ
0.5
2
%
−35
VOLTAGE-DIVIDER
Divider Resistance
Accuracy
(1)
(2)
(3)
Total, Pin 6 to 4
(3)
8
Unless otherwise stated, all specifications apply with the following conditions:
3 VDC ≤ V+ ≤ 20 VDC
VREF, VRHI, VRLO ≤ (V+ − 1.5V)
3 VDC ≤ VLED ≤ V+
0V ≤ VIN ≤ V+ − 1.5V
−0.015V ≤ VRLO ≤ 12VDC
TA = +25°C, IL(REF) = 0.2 mA, VLED = 3.0V, pin 9 connected to pin 3 (Bar Mode).
−0.015V ≤ VRHI ≤ 12 VDCFor higher power dissipations, pulse testing is used.
Pin 5 input current must be limited to ±3mA. The addition of a 39k resistor in series with pin 5 allows ±100V signals without damage.
Accuracy is measured referred to +10.000VDC at pin 6, with 0.000 VDC at pin 4. At lower full-scale voltages, buffer and comparator offset
voltage may add significant error.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
3
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2) (continued)
Parameter
Conditions
(1)
Min
Typ
Max
Units
1.2
1.28
1.34
V
VOLTAGE REFERENCE
Output Voltage
0.1 mA ≤ IL(REF) ≤ 4 mA,
V+ = VLED = 5V
Line Regulation
3V ≤ V+ ≤ 18V
0.01
0.03
%/V
Load Regulation
0.1 mA ≤ IL(REF) ≤ 4 mA,
V+ = VLED = 5V
0.4
2
%
Output Voltage Change with
Temperature
0°C ≤ TA ≤ +70°C, IL(REF) = 1 mA,
V+ = 5V
1
Adjust Pin Current
75
%
120
μA
mA
OUTPUT DRIVERS
LED Current
V+ = VLED = 5V, IL(REF) = 1 mA
LED Current Difference (Between
Largest and Smallest LED Currents)
VLED = 5V
LED Current Regulation
2V ≤ VLED ≤ 17V
10
13
ILED = 2 mA
0.12
0.4
ILED = 20 mA
1.2
3
ILED = 2 mA
0.1
0.25
ILED = 20 mA
1
3
Dropout Voltage
ILED(ON) = 20 mA, VLED = 5V,
ΔILED = 2 mA
Saturation Voltage
ILED = 2.0 mA, IL(REF) = 0.4 mA
Output Leakage, Each Collector
(Bar Mode)
(4)
Output Leakage
(Dot Mode)
(4)
7
1.5
mA
mA
V
0.15
0.4
V
0.1
10
μA
0.1
10
μA
150
450
μA
V+ = 5V,
IL(REF) = 0.2 mA
2.4
4.2
mA
V+ = 20V,
IL(REF) = 1.0 mA
6.1
9.2
mA
Pins 10–18
Pin 1
60
SUPPLY CURRENT
Standby Supply Current
(All Outputs Off)
(4)
4
Bar mode results when pin 9 is within 20mV of V+. Dot mode results when pin 9 is pulled at least 200mV below V+ or left open circuit.
LED No. 10 (pin 10 output current) is disabled if pin 9 is pulled 0.9V or more below VLED.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
DEFINITION OF TERMS
Accuracy: The difference between the observed threshold voltage and the ideal threshold voltage for each
comparator. Specified and tested with 10V across the internal voltage divider so that resistor ratio
matching error predominates over comparator offset voltage.
Adjust Pin Current: Current flowing out of the reference adjust pin when the reference amplifier is in the linear
region.
Comparator Gain: The ratio of the change in output current (ILED) to the change in input voltage (VIN) required
to produce it for a comparator in the linear region.
Dropout Voltage: The voltage measured at the current source outputs required to make the output current fall
by 10%.
Input Bias Current: Current flowing out of the signal input when the input buffer is in the linear region.
LED Current Regulation: The change in output current over the specified range of LED supply voltage (VLED)
as measured at the current source outputs. As the forward voltage of an LED does not change
significantly with a small change in forward current, this is equivalent to changing the voltage at the LED
anodes by the same amount.
Line Regulation: The average change in reference output voltage over the specified range of supply voltage
(V+).
Load Regulation: The change in reference output voltage (VREF) over the specified range of load current
(IL(REF)).
Offset Voltage: The differential input voltage which must be applied to each comparator to bias the output in
the linear region. Most significant error when the voltage across the internal voltage divider is small.
Specified and tested with pin 6 voltage (VRHI) equal to pin 4 voltage (VRLO).
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
5
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
6
Supply Current vs Temperature
Operating Input Bias Current vs Temperature
Figure 2.
Figure 3.
Reference Voltage vs Temperature
Reference Adjust Pin Current vs Temperature
Figure 4.
Figure 5.
LED Current-Regulation Dropout
LED Driver Saturation Voltage
Figure 6.
Figure 7.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Input Current Beyond Signal Range (Pin 5)
LED Current vs Reference Loading
Figure 8.
Figure 9.
LED Driver Current Regulation
Total Divider Resistance vs Temperature
Figure 10.
Figure 11.
Common-Mode Limits
Output Characteristics
Figure 12.
Figure 13.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
7
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
BLOCK DIAGRAM
(Showing Simplest Application)
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
FUNCTIONAL DESCRIPTION
The simplified LM3914 block diagram is to give the general idea of the circuit's operation. A high input
impedance buffer operates with signals from ground to 12V, and is protected against reverse and overvoltage
signals. The signal is then applied to a series of 10 comparators; each of which is biased to a different
comparison level by the resistor string.
In the example illustrated, the resistor string is connected to the internal 1.25V reference voltage. In this case, for
each 125mV that the input signal increases, a comparator will switch on another indicating LED. This resistor
divider can be connected between any 2 voltages, providing that they are 1.5V below V+ and no less than V−. If
an expanded scale meter display is desired, the total divider voltage can be as little as 200mV. Expanded-scale
meter displays are more accurate and the segments light uniformly only if bar mode is used. At 50mV or more
per step, dot mode is usable.
INTERNAL VOLTAGE REFERENCE
The reference is designed to be adjustable and develops a nominal 1.25V between the REF OUT (pin 7) and
REF ADJ (pin 8) terminals. The reference voltage is impressed across program resistor R1 and, since the
voltage is constant, a constant current I1 then flows through the output set resistor R2 giving an output voltage of:
Since the 120μA current (max) from the adjust terminal represents an error term, the reference was designed to
minimize changes of this current with V+ and load changes.
CURRENT PROGRAMMING
A feature not completely illustrated by the block diagram is the LED brightness control. The current drawn out of
the reference voltage pin (pin 7) determines LED current. Approximately 10 times this current will be drawn
through each lighted LED, and this current will be relatively constant despite supply voltage and temperature
changes. Current drawn by the internal 10-resistor divider, as well as by the external current and voltage-setting
divider should be included in calculating LED drive current. The ability to modulate LED brightness with time, or
in proportion to input voltage and other signals can lead to a number of novel displays or ways of indicating input
overvoltages, alarms, etc.
MODE PIN USE
Pin 9, the Mode Select input controls chaining of multiple LM3914s, and controls bar or dot mode operation. The
following tabulation shows the basic ways of using this input. Other more complex uses will be illustrated in the
applications.
Bar Graph Display: Wire Mode Select (pin 9) directly to pin 3 (V+ pin).
Dot Display, Single LM3914 Driver: Leave the Mode Select pin open circuit.
Dot Display, 20 or More LEDs: Connect pin 9 of the first driver in the series (i.e., the one with the lowest input
voltage comparison points) to pin 1 of the next higher LM3914 driver. Continue connecting pin 9 of lower input
drivers to pin 1 of higher input drivers for 30, 40, or more LED displays. The last LM3914 driver in the chain will
have pin 9 wired to pin 11. All previous drivers should have a 20k resistor in parallel with LED No. 9 (pin 11 to
VLED).
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
9
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
MODE PIN FUNCTIONAL DESCRIPTION
This pin actually performs two functions. Refer to the simplified block diagram below.
*High for bar
Figure 14. Block Diagram of Mode Pin Description
DOT OR BAR MODE SELECTION
The voltage at pin 9 is sensed by comparator C1, nominally referenced to (V+ − 100mV). The chip is in bar mode
when pin 9 is above this level; otherwise it's in dot mode. The comparator is designed so that pin 9 can be left
open circuit for dot mode.
Taking into account comparator gain and variation in the 100mV reference level, pin 9 should be no more than
20mV below V+ for bar mode and more than 200mV below V+ (or open circuit) for dot mode. In most
applications, pin 9 is either open (dot mode) or tied to V+ (bar mode). In bar mode, pin 9 should be connected
directly to pin 3. Large currents drawn from the power supply (LED current, for example) should not share this
path so that large IR drops are avoided.
DOT MODE CARRY
In order for the display to make sense when multiple LM3914s are cascaded in dot mode, special circuitry has
been included to shut off LED No. 10 of the first device when LED No. 1 of the second device comes on. The
connection for cascading in dot mode has already been described and is depicted below.
As long as the input signal voltage is below the threshold of the second LM3914, LED No. 11 is off. Pin 9 of
LM3914 No. 1 thus sees effectively an open circuit so the chip is in dot mode. As soon as the input voltage
reaches the threshold of LED No. 11, pin 9 of LM3914 No. 1 is pulled an LED drop (1.5V or more) below VLED.
This condition is sensed by comparator C2, referenced 600mV below VLED. This forces the output of C2 low,
which shuts off output transistor Q2, extinguishing LED No. 10.
VLED is sensed via the 20k resistor connected to pin 11. The very small current (less than 100μA) that is diverted
from LED No. 9 does not noticeably affect its intensity.
An auxiliary current source at pin 1 keeps at least 100μA flowing through LED No. 11 even if the input voltage
rises high enough to extinguish the LED. This ensures that pin 9 of LM3914 No. 1 is held low enough to force
LED No. 10 off when any higher LED is illuminated. While 100μA does not normally produce significant LED
illumination, it may be noticeable when using high-efficiency LEDs in a dark environment. If this is bothersome,
the simple cure is to shunt LED No. 11 with a 10k resistor. The 1V IR drop is more than the 900mV worst case
required to hold off LED No. 10 yet small enough that LED No. 11 does not conduct significantly.
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
OTHER DEVICE CHARACTERISTICS
The LM3914 is relatively low-powered itself, and since any number of LEDs can be powered from about 3V, it is
a very efficient display driver. Typical standby supply current (all LEDs OFF) is 1.6mA (2.5mA max). However,
any reference loading adds 4 times that current drain to the V+ (pin 3) supply input. For example, an LM3914
with a 1mA reference pin load (1.3k), would supply almost 10mA to every LED while drawing only 10mA from its
V+ pin supply. At full-scale, the IC is typically drawing less than 10% of the current supplied to the display.
The display driver does not have built-in hysteresis so that the display does not jump instantly from one LED to
the next. Under rapidly changing signal conditions, this cuts down high frequency noise and often an annoying
flicker. An “overlap” is built in so that at no time between segments are all LEDs completely OFF in the dot mode.
Generally 1 LED fades in while the other fades out over a mV or more of range (1). The change may be much
more rapid between LED No. 10 of one device and LED No. 1 of a second device “chained” to the first.
The LM3914 features individually current regulated LED driver transistors. Further internal circuitry detects when
any driver transistor goes into saturation, and prevents other circuitry from drawing excess current. This results in
the ability of the LM3914 to drive and regulate LEDs powered from a pulsating DC power source, i.e., largely
unfiltered. (Due to possible oscillations at low voltages a nominal bypass capacitor consisting of a 2.2μF solid
tantalum connected from the pulsating LED supply to pin 2 of the LM3914 is recommended.) This ability to
operate with low or fluctuating voltages also allows the display driver to interface with logic circuitry, opto-coupled
solid-state relays, and low-current incandescent lamps.
Figure 15. Cascading LM3914s in Dot Mode
(1)
Accuracy is measured referred to +10.000VDC at pin 6, with 0.000 VDC at pin 4. At lower full-scale voltages, buffer and comparator offset
voltage may add significant error.
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
11
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
Typical Applications
Figure 16. Zero-Center Meter, 20-Segment
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
*This application illustrates that the LED supply needs practically no filtering
Calibration: With a precision meter between pins 4 and 6 adjust R1 for voltage VD of 1.20V. Apply 4.94V to pin 5,
and adjust R4 until LED No. 5 just lights. The adjustments are non-interacting.
Figure 17. Expanded Scale Meter, Dot or Bar
Table 1. Application Example: Grading 5V Regulators
Highest No.
LED on
Color
VOUT(MIN)
10
Red
5.54
9
Red
5.42
8
Yellow
5.30
7
Green
5.18
6
Green
5.06
5V
5
Green
4.94
4
Green
4.82
3
Yellow
4.7
2
Red
4.58
1
Red
4.46
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
13
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
LEDs light up as illustrated with the upper lit LED indicating the actual input voltage. The display appears to increase
resolution and provides an analog indication of overrange.
Figure 18. “Exclamation Point” Display
*The input to the Dot-Bar Switch may be taken from cathodes of other LEDs. Display will change to bar as soon as
the LED so selected begins to light.
Figure 19. Indicator and Alarm, Full-Scale Changes Display from Dot to Bar
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
Full-scale causes the full bar display to flash. If the junction of R1 and C1 is connected to a different LED cathode, the
display will flash when that LED lights, and at any higher input signal.
Figure 20. Bar Display with Alarm Flasher
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
15
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
Hysteresis is 0.5 mV to 1 mV
Figure 21. Adding Hysteresis (Single Supply, Bar Mode Only)
16
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
Figure 22.
The LED currents are approximately 10mA, and the LM3914 outputs operate in saturation for minimum dissipation.
*This point is partially regulated and decreases in voltage with temperature. Voltage requirements of the LM3914 also
decrease with temperature.
Figure 23. Operating with a High Voltage Supply (Dot Mode Only)
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
17
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
*The exact wiring arrangement of this schematic shows the need for Mode Select (pin 9) to sense the V+ voltage
exactly as it appears on pin 3.
Programs LEDs to 10mA
Figure 24. 20-Segment Meter with Mode Switch
APPLICATION HINTS
Three of the most commonly needed precautions for using the LM3914 are shown in the first typical application
drawing showing a 0V–5V bar graph meter. The most difficult problem occurs when large LED currents are being
drawn, especially in bar graph mode. These currents flowing out of the ground pin cause voltage drops in
external wiring, and thus errors and oscillations. Bringing the return wires from signal sources, reference ground
and bottom of the resistor string (as illustrated) to a single point very near pin 2 is the best solution.
Long wires from VLED to LED anode common can cause oscillations. Depending on the severity of the problem
0.05μF to 2.2μF decoupling capacitors from LED anode common to pin 2 will damp the circuit. If LED anode line
wiring is inaccessible, often similar decoupling from pin 1 to pin 2 will be sufficient.
18
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
If LED turn ON seems slow (bar mode) or several LEDs light (dot mode), oscillation or excessive noise is usually
the problem. In cases where proper wiring and bypassing fail to stop oscillations, V+ voltage at pin 3 is usually
below suggested limits. Expanded scale meter applications may have one or both ends of the internal voltage
divider terminated at relatively high value resistors. These high-impedance ends should be bypassed to pin 2
with at least a 0.001μF capacitor, or up to 0.1μF in noisy environments.
Power dissipation, especially in bar mode should be given consideration. For example, with a 5V supply and all
LEDs programmed to 20mA the driver will dissipate over 600mW. In this case a 7.5Ω resistor in series with the
LED supply will cut device heating in half. The negative end of the resistor should be bypassed with a 2.2μF solid
tantalum capacitor to pin 2 of the LM3914.
Turning OFF of most of the internal current sources is accomplished by pulling positive on the reference with a
current source or resistance supplying 100μA or so. Alternately, the input signal can be gated OFF with a
transistor switch.
Other special features and applications characteristics will be illustrated in the following applications schematics.
Notes have been added in many cases, attempting to cover any special procedures or unusual characteristics of
these applications. A special section called APPLICATION TIPS FOR THE LM3914 ADJUSTABLE REFERENCE
has been included with these schematics.
APPLICATION TIPS FOR THE LM3914 ADJUSTABLE REFERENCE
Greatly Expanded Scale (Bar Mode Only)
Placing the LM3914 internal resistor divider in parallel with a section (≃230Ω) of a stable, low resistance divider
greatly reduces voltage changes due to IC resistor value changes with temperature. Voltage V1 should be
trimmed to 1.1V first by use of R2. Then the voltage V2 across the IC divider string can be adjusted to 200mV,
using R5 without affecting V1. LED current will be approximately 10mA.
Non-Interacting Adjustments For Expanded Scale Meter (4.5V to 5V, Bar or Dot Mode)
This arrangement allows independent adjustment of LED brightness regardless of meter span and zero
adjustments.
First, V1 is adjusted to 5V, using R2. Then the span (voltage across R4) can be adjusted to exactly 0.5V using
R6 without affecting the previous adjustment.
R9 programs LED currents within a range of 2.2mA to 20mA after the above settings are made.
Figure 25. Greatly Expanded Scale (Bar Mode Only)
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
19
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
ADJUSTING LINEARITY OF SEVERAL STACKED DIVIDERS
Three internal voltage dividers are shown connected in series to provide a 30-step display. If the resulting analog
meter is to be accurate and linear the voltage on each divider must be adjusted, preferably without affecting any
other adjustments. To do this, adjust R2 first, so that the voltage across R5 is exactly 1V. Then the voltages
across R3 and R4 can be independently adjusted by shunting each with selected resistors of 6kΩ or higher
resistance. This is possible because the reference of LM3914 No. 3 is acting as a constant current source.
The references associated with LM3914s No. 1 and No. 2 should have their Ref Adj pins (pin 8) wired to ground,
and their Ref Outputs loaded by a 620Ω resistor to ground. This makes available similar 20mA current outputs to
all the LEDs in the system.
If an independent LED brightness control is desired (as in the previous application), a unity gain buffer, such as
the LM310, should be placed between pin 7 and R1, similar to the previous application.
(4.5V to 5V, Bar or Dot Mode)
Figure 26. Non-Interacting Adjustments for Expanded Scale Meter
20
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
Figure 27. Adjusting Linearity of Several Stacked Dividers
OTHER APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
“Slow”—fade bar or dot display (doubles resolution)
20-step meter with single pot brightness control
10-step (or multiples) programmer
Multi-step or “staging” controller
Combined controller and process deviation meter
Direction and rate indicator (to add to DVMs)
Exclamation point display for power saving
Graduations can be added to dot displays. Dimly light every other LED using a resistor to ground
Electronic “meter-relay”—display could be circle or semi-circle
Moving “hole” display—indicator LED is dark, rest of bar lit
Drives vacuum-fluorescent and LCDs using added passive parts
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
21
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
CONNECTION DIAGRAM
Figure 28. Top View
PLCC Package
See Package Number FN0020A
Figure 29. PDIP Package
Top View
See Package Number NFK0018A
22
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
LM3914
www.ti.com
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
LM3914 MDC MWC DOT/BAR DISPLAY DRIVER
Figure 30. Die Layout (D - Step)
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
23
LM3914
SNVS761B – JANUARY 2000 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
•
24
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 23
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3914
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jul-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
LM3914N-1
ACTIVE
PDIP
NFK
18
20
TBD
Call TI
Call TI
0 to 70
LM3914N-1
LM3914N-1/NOPB
ACTIVE
PDIP
NFK
18
20
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
0 to 70
LM3914N-1
LM3914V
ACTIVE
PLCC
FN
20
40
TBD
Call TI
Call TI
0 to 70
LM3914V
LM3914V/NOPB
ACTIVE
PLCC
FN
20
40
Green (RoHS
& no Sb/Br)
CU SN
Level-2A-250C-4
WEEK
0 to 70
LM3914V
LM3914VX
ACTIVE
PLCC
FN
20
1000
TBD
Call TI
Call TI
0 to 70
LM3914V
LM3914VX/NOPB
ACTIVE
PLCC
FN
20
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-2A-250C-4
WEEK
0 to 70
LM3914V
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jul-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
NFK0018A
N0018A
NA18A (Rev B)
www.ti.com
MECHANICAL DATA
MPLC004A – OCTOBER 1994
FN (S-PQCC-J**)
PLASTIC J-LEADED CHIP CARRIER
20 PIN SHOWN
Seating Plane
0.004 (0,10)
0.180 (4,57) MAX
0.120 (3,05)
0.090 (2,29)
D
D1
0.020 (0,51) MIN
3
1
19
0.032 (0,81)
0.026 (0,66)
4
E
18
D2 / E2
E1
D2 / E2
8
14
0.021 (0,53)
0.013 (0,33)
0.007 (0,18) M
0.050 (1,27)
9
13
0.008 (0,20) NOM
D/E
D2 / E2
D1 / E1
NO. OF
PINS
**
MIN
MAX
MIN
MAX
MIN
MAX
20
0.385 (9,78)
0.395 (10,03)
0.350 (8,89)
0.356 (9,04)
0.141 (3,58)
0.169 (4,29)
28
0.485 (12,32)
0.495 (12,57)
0.450 (11,43)
0.456 (11,58)
0.191 (4,85)
0.219 (5,56)
44
0.685 (17,40)
0.695 (17,65)
0.650 (16,51)
0.656 (16,66)
0.291 (7,39)
0.319 (8,10)
52
0.785 (19,94)
0.795 (20,19)
0.750 (19,05)
0.756 (19,20)
0.341 (8,66)
0.369 (9,37)
68
0.985 (25,02)
0.995 (25,27)
0.950 (24,13)
0.958 (24,33)
0.441 (11,20)
0.469 (11,91)
84
1.185 (30,10)
1.195 (30,35)
1.150 (29,21)
1.158 (29,41)
0.541 (13,74)
0.569 (14,45)
4040005 / B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated