TI UC2543DWG4

UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
Power Supply Supervisory Circuit
FEATURES
•
•
•
•
•
•
•
Both over- and under-voltage sensing circuits can be
externally programmed for minimum time duration of
fault before triggering. All functions contain open
collector outputs which can be used independently or
wire-or’ed together, and although the SCR trigger is
directly connected only to the over-voltage sensing
circuit, it may be optionally activated by any of the
other outputs, or from an external signal. The O.V.
circuit also includes an optional latch and external
reset capability.
Includes Over-Voltage, Under-Voltage, and
Current Sensing Circuits
Internal 1% Accurate Reference
Programmable Time Delays
SCR “Crowbar” Drive of 300 mA
Remote Activation Capability
Optional Over-Voltage Latch
Uncommitted Comparator Inputs for Low
Voltage Sensing (UC1544 Series Only)
DESCRIPTION
The monolithic integrated circuits contain all the
functions necessary to monitor and control the output
of a sophisticated power supply system.
Over-voltage (O.V.) sensing with provision to trigger
an external SCR “crowbar” shutdown; an
undervoltage (U.V.) circuit which can be used to
monitor either the output or to sample the input line
voltage; and a third op amp/comparator usable for
current sensing (C.L.) are all included in this device,
together with an independent, accurate reference
generator.
The UC1544/2544/3544 devices have the added
versatility of completely uncommitted inputs to the
voltage sensing comparators so that levels less than
2.5 V may be monitored by dividing down the internal
reference voltage. The current sense circuit may be
used with external compensation as a linear amplifier
or as a highgain comparator. Although nominally set
for zero input offset, a fixed threshold may be added
with an external resistor. Instead of current limiting,
this circuit may also be used as an additional voltage
monitor.
The reference generator circuit is internally trimmed
to eliminate the need for external potentiometers and
the entire circuit may be powered directly from either
the output being monitored or from a separate bias
voltage.
BLOCK DIAGRAM
NOTE:
For each terminal, first number refers to 1543 series, second to 1544 series.
*On 1543 series, this function is internally connected to VREF.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1997–2007, Texas Instruments Incorporated
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
Connection Diagrams
UC 1543
UC 2543
UC 3543
DIL-16, SOIC-16 (TOP VIEW)
J or N, DW Package
(Also W Package for the UC1543 Only)
DIL-18, SOIC-18 (TOP VIEW)
J or N, DW Package
SCR Trigger
SCR Trigger
1
16
VIN
Remote Activate
2
15
VREF
Reset
3
14
Ground
O.V. Indicate
4
13
C.L. Output
O.V. Delay
5
12
Offset/Comp
O.V. Input
6
11
C.L. N.I. Input
U.V. Input
7
10
C.L. INV. Input
U.V. Delay
8
9
U.V. Indicate
PLCC-20, LCC-20
(TOP VIEW)
Q or L Package
3
2
1
20
PACKAGE PIN FUNCTION
FUNCTION
PIN
19
4
18
5
17
6
16
7
15
8
14
9
10
11
12
13
N/C
SCR Trigger
Remote Activate
Reset
O.V. Indicate
N/C
O.V. Delay
O.V. Input
N/C
N/C
U.V. Input
U.V. Delay
U.V. Indicate
C.L. INV. Input
C.L. N.I. Input
Offset/Comp
C.L. Output
Ground
VREF
VIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
UC 1544
UC 2544
UC 3544
1
18
VIN
Remote Activate
2
17
VREF
Reset
3
16
Ground
O.V. Indicate
4
15
C.L. Output
O.V. Delay
5
14
Offset/Comp
O.V. N.I. Input
6
13
C.L. N.I. Input
O.V. Inv. Input
7
12
C.L. INV. Input
U.V. N.I. Input
8
11
U.V. Indicate
U.V. Inv. Input
9
10
U.V. Delay
PLCC-20, LCC-20
(TOP VIEW)
Q or L Package
3
2
1
20
PACKAGE PIN FUNCTION
FUNCTION
PIN
19
4
18
5
17
6
16
7
15
8
14
9
10
11
12
13
N/C
SCR Trigger
Remote Activate
Reset
O.V. Indicate
N/C
O.V. Delay
O.V. N.I. Input
O.V. INV. Input
U.V. N.I. Input
U.V. INV. Input
U.V. Delay
U.V. Indicate
C.L. INV. Input
C.L. N.I. Input
Offset/Comp
C.L. Output
Ground
VREF
VIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VALUE
VIN
Input supply voltage
40
Sense inputs, voltage range
SCR trigger current
0 to VIN
(2)
-600
Tstg
(1)
(2)
2
V
mA
Indicator output voltage
40
V
Indicator output sink current
50
mA
1000
mW
Power dissipation (package limitation)
TJ
UNIT
Operating temperature range
UC1543, UC1544
-55 to 125
UC2543, UC2544
-25 to 85
UC3543, UC3544
0 to 70
Storage temperature range
-65 to 150
Currents are positive-into, negative-out of the specified terminal.
At higher input voltages, a dissipation limiting resistor, RG, is required.
Submit Documentation Feedback
°C
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, these specifications apply for TA = -55°C to 125°C for theUC1543 and UC1544; -25°C to 85°C for
the UC2543 and UC2544; and 0°C to 70°C for the UC3543 and UC3544. Electrical tests are performed with VIN = 10 V and
2-kΩ pull-up resistors on all indicator outputs. All electrical specifications for the UC1544, UC2544, and UC3544 devices are
tested with the inverting over-voltage input and the non-inverting under-voltage input externallyconnected to the 2.5 V
reference. TA = TJ.
PARAMETER
TEST CONDITIONS
UC1543/UC1544/UC2543/
UC2544
MIN
VIN
Input voltage range
ICC
Supply current
TYP
UC3543/UC3544
MAX
MIN
TYP
UNIT
MAX
TJ = 25°C to TMAX
4.5
40
4.5
40
TMIN to TMAX
4.7
40
4.7
40
VIN = 40 V, output open,
TJ = 25°C
7
TMIN≤ TJ≤ TMAX
10
7
15
10
V
mA
15
Reference Section
VOUT
Output voltage
TJ = 25°C
2.48
Over temperature range
2.45
2.5
2.52
2.45
2.55
2.40
2.50
2.55
2.60
Line regulation
VIN = 5 to 30 V
1
5
1
5
Load regulation
IREF = 0 to 10 mA
1
10
1
10
Short circuit current
VREF = 0
-20
-40
-20
-40
-10
Temperature stability
-12
50
50
V
mV
mA
ppm/°C
SCR Trigger Section
Peak output current
VIN = 5V, RG = 0, VO = 0
Peak output voltage
VIN = 15 V, IO = -100 mA
-100
-300
12
13
-600
-100
-300
12
13
Output OFF voltage
VIN = 40 V
Remote activate current
R/A Pin = GND
Remote activate voltage
R/A Pin Open
Reset current
Reset = GND, R/A = GND
Reset voltage
Reset open, R/A = GND
Output current rise time
RL = 50, TJ = 25°C, CD = 0
400
400
Prop. delay from R/A
RL = 50, TJ = 25°C, CD = 0
300
300
Prop. delay from O/V input
RL = 50, TJ = 25°C, CD = 0
500
500
-600
0
0.1
0
0.1
-0.4
-0.8
-0.4
-0.8
2
6
2
6
-0.4
-0.8
-0.4
-0.8
2
6
2
6
mA
V
mA
V
mA
V
mA/µs
ns
Comparator Section
Input threshold (Input
voltage rising on O.V. and
falling on U.V.)
TJ = 25°C
2.45
Over temperature range
2.40
Input hysteresis
Input bias current
2.50
2.55
2.40
2.60
2.35
25
Sense input = 0 V
2.50
2.60
2.65
25
mV
-0.3
-1.0
-0.3
-1.0
Delay saturation
0.2
0.5
0.2
0.5
Delay high level
6
7
6
7
V
µA
VO = 0
-250
-300
-250
-300
Indicate saturation
IL = 10 mA
0.2
0.5
0.2
0.5
V
Indicate leakage
VIND = 40 V
0.01
1.0
0.01
1.0
µA
Input over drive = 200 mV,
TJ = 25°C, CD = 0
400
400
ns
Input over drive = 200 mV,
TJ = 25°C, CD = 1 µF
10
10
ms
Submit Documentation Feedback
-200
µA
Delay charging current
Propagation delay
-200
V
3
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise stated, these specifications apply for TA = -55°C to 125°C for theUC1543 and UC1544; -25°C to 85°C for
the UC2543 and UC2544; and 0°C to 70°C for the UC3543 and UC3544. Electrical tests are performed with VIN = 10 V and
2-kΩ pull-up resistors on all indicator outputs. All electrical specifications for the UC1544, UC2544, and UC3544 devices are
tested with the inverting over-voltage input and the non-inverting under-voltage input externallyconnected to the 2.5 V
reference. TA = TJ.
Current Limit Section
Input voltage range
Input Bias Current
Input offset voltage
VIN -3V
V
Offset pin open, VCM = 0
0
-0.3
VIN -3V
-1.0
0
-0.3
-1.0
µA
Offset pin open, VCM = 0
0
10
0
10
120
80
100
120
10k from offset pin to GND
80
100
CMRR
0 ≤ VCM≤ 12 V, VIN = 15 V
60
70
60
70
AVOL
Offset pin open, VCM = 0
V,
RL = 10 kΩ to 15 kΩ,
VOUT = 1 to 6 V
72
80
72
80
Output saturation
IL = 10 mA
0.2
0.5
0.2
0.5
Output leakage
VIND = 40 V
0.01
1.0
0.01
1.0
Small signal bandwidth
AV = 0dB, TJ = 25°C
Propagation delay
VOVERDRIVE = 100 mV,
TJ = 25°C
5
5
200
200
TYPICAL CHARACTERISTICS
Figure 1.
4
Figure 2.
Submit Documentation Feedback
mV
dB
V
µA
MHz
ns
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
Current Limit Input Threshold
ID
Figure 3.
Figure 4.
Current Limit Amplifier Gain
Current Limit Amplifier Frequency Response
Figure 5.
Figure 6.
Submit Documentation Feedback
5
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
APPLICATION INFORMATION
The values for the external components are determined as follows:
VTH =
Current limit input threshold,
1000
R1
CS is determined by the current loop dynamics
IP @
VTH VO æ R 2 ö
+
ç
÷
RSC RSC è R 2 + R3 ø
I SC =
VTH
RSC
Peak current to load,
Short circuit current,
VO( low ) =
Low output voltage limit,
2.5( R 4 + R5 + R6 )
R5 + R 6
VO( high ) =
High output voltage limit,
2 .5( R 4 + R 5 + R 6 )
R6
Voltage sensing delay, tD = 10,000Cd
RG >
SCR trigger power limiting resistor,
VIN - 5
0 .2
Figure 7. Typical Application
6
Submit Documentation Feedback
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
APPLICATION INFORMATION (continued)
Figure 8. Sensing Multiple Supply Voltages
Figure 9. Input Line Monitor
Submit Documentation Feedback
7
UC1543,, UC1544
UC2543, UC2544
UC3543, UC3544
www.ti.com
SLUS188A – APRIL 1997 – REVISED FEBRUARY 2007
APPLICATION INFORMATION (continued)
Figure 10. Overcurrent Shutdown
8
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
5962-8774001EA
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8774001EA
UC1543J/883B
5962-8774001FA
ACTIVE
CFP
W
16
25
TBD
A42
N / A for Pkg Type
5962-8774002VA
OBSOLETE
CDIP
J
18
TBD
Call TI
Call TI
-55 to 125
UC1543J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
UC1543J
UC1543J883B
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-55 to 125
5962-8774001EA
UC1543J/883B
UC1543L
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
UC1543L
UC1543L883B
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
UC1543L/
883B
UC1543W883B
ACTIVE
CFP
W
16
25
TBD
A42
N / A for Pkg Type
5962-8774001FA
UC1543W/883B
5962-8774001FA
UC1543W/883B
UC1544J
OBSOLETE
CDIP
J
18
TBD
Call TI
Call TI
-55 to 125
UC1544J883B
OBSOLETE
CDIP
J
18
TBD
Call TI
Call TI
-55 to 125
UC1544L
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
-55 to 125
UC1544L883B
OBSOLETE
LCCC
FK
20
TBD
Call TI
Call TI
-55 to 125
UC2543DW
NRND
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2543DW
UC2543DWG4
NRND
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2543DW
UC2543J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
-25 to 85
UC2543J
UC2543N
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2543N
UC2543NG4
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2543N
UC2544-W
ACTIVE
WAFERSALE
YS
0
TBD
Call TI
Call TI
UC2544DW
NRND
SOIC
DW
18
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2544DW
UC2544DWG4
NRND
SOIC
DW
18
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
UC2544DW
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
UC2544J
OBSOLETE
CDIP
J
18
TBD
Call TI
Call TI
-40 to 85
UC2544N
NRND
PDIP
N
18
20
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2544N
UC2544NG4
NRND
PDIP
N
18
20
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
-40 to 85
UC2544N
UC3543J
ACTIVE
CDIP
J
16
1
TBD
A42
N / A for Pkg Type
0 to 70
UC3543J
UC3543N
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3543N
UC3543NG4
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3543N
UC3544J
OBSOLETE
CDIP
J
18
TBD
Call TI
Call TI
0 to 70
UC3544N
NRND
PDIP
N
18
20
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3544N
UC3544NG4
NRND
PDIP
N
18
20
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
0 to 70
UC3544N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UC1543, UC1544, UC2543, UC2543M, UC3543, UC3543M, UC3544 :
• Catalog: UC3543, UC3544, UC2543, UC3543M, UC3543
• Military: UC2543M, UC1543, UC1543, UC1544
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Military - QML certified for Military and Defense Applications
Addendum-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated