TI MSP-FET430PIF

MSP430 Hardware Tools
User's Guide
Literature Number: SLAU278F
May 2009 – Revised December 2010
2
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Contents
....................................................................................................................................... 9
Get Started Now! ............................................................................................................... 13
1.1
Flash Emulation Tool (FET) Overview .................................................................................. 14
1.2
Kit Contents, MSP-FET430PIF .......................................................................................... 14
1.3
Kit Contents, eZ430-F2013 .............................................................................................. 14
1.4
Kit Contents, eZ430-T2012 .............................................................................................. 14
1.5
Kit Contents, eZ430-RF2500 ............................................................................................ 15
1.6
Kit Contents, eZ430-RF2500T ........................................................................................... 15
1.7
Kit Contents, eZ430-RF2500-SEH ...................................................................................... 15
1.8
Kit Contents, eZ430-Chronos-xxx ....................................................................................... 15
1.9
Kit Contents, MSP-FET430UIF .......................................................................................... 15
1.10 Kit Contents, MSP-FET430xx ............................................................................................ 16
1.11 Kit Contents, FET430Fx137RF900 ..................................................................................... 17
1.12 Kit Contents, MSP-TS430xx ............................................................................................. 17
1.13 Kit Contents, EM430Fx137RF900 ....................................................................................... 19
1.14 Hardware Installation, MSP-FET430PIF ............................................................................... 19
1.15 Hardware Installation, MSP-FET430UIF ............................................................................... 20
1.16 Hardware Installation, eZ430-F2013, eZ430-RF2500, eZ430-Chronos ............................................ 20
1.17 Hardware Installation, MSP-FET430Uxx, MSP-TS430xxx, FET430Fx137RF900, EM430Fx137RF900 ...... 20
1.18 Important MSP430 Documents on the CD-ROM and Web .......................................................... 21
Design Considerations for In-Circuit Programming ............................................................... 23
2.1
Signal Connections for In-System Programming and Debugging ................................................... 24
2.2
External Power ............................................................................................................. 27
2.3
Bootstrap Loader (BSL) .................................................................................................. 27
Frequently Asked Questions and Known Issues ................................................................... 29
A.1
Hardware FAQs ............................................................................................................ 30
A.2
Known Issues .............................................................................................................. 32
Hardware .......................................................................................................................... 33
B.1
MSP-TS430PW14 ......................................................................................................... 34
B.2
MSP-TS430L092 .......................................................................................................... 37
B.3
MSP-TS430L092 Active Cable .......................................................................................... 40
B.4
MSP-TS430PW24 ......................................................................................................... 43
B.5
MSP-TS430DW28 ......................................................................................................... 46
B.6
MSP-TS430PW28 ......................................................................................................... 49
B.7
MSP-TS430PW28A ....................................................................................................... 52
B.8
MSP-TS430DA38 .......................................................................................................... 55
B.9
MSP-TS430QFN23x0 ..................................................................................................... 58
B.10 MSP-TS430RSB40 ........................................................................................................ 61
B.11 MSP-TS430RHA40A ...................................................................................................... 64
B.12 MSP-TS430DL48 .......................................................................................................... 67
B.13 MSP-TS430RGZ48B ...................................................................................................... 70
B.14 MSP-TS430PM64 ......................................................................................................... 73
B.15 MSP-TS430PM64A ....................................................................................................... 76
B.16 MSP-TS430RGC64B ..................................................................................................... 79
Preface
1
2
A
B
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Contents
© 2009–2010, Texas Instruments Incorporated
3
www.ti.com
B.17
B.18
B.19
B.20
B.21
B.22
B.23
B.24
B.25
B.26
B.27
B.28
B.29
MSP-TS430RGC64USB .................................................................................................. 82
MSP-TS430PN80 .......................................................................................................... 86
MSP-TS430PN80A ........................................................................................................ 89
MSP-TS430PN80USB .................................................................................................... 91
MSP-TS430PZ100 ........................................................................................................ 96
MSP-TS430PZ100A ....................................................................................................... 99
MSP-TS430PZ100B ..................................................................................................... 102
MSP-TS430PZ5x100 .................................................................................................... 105
MSP-TS430PZ100USB ................................................................................................. 107
EM430F5137RF900 ..................................................................................................... 112
EM430F6137RF900 ..................................................................................................... 116
MSP-FET430PIF ......................................................................................................... 120
MSP-FET430UIF ......................................................................................................... 122
B.29.1 MSP-FET430UIF Revision History .......................................................................... 127
.............................................................................................. 129
C.1
Hardware Installation .................................................................................................... 130
Document Revision History ........................................................................................................ 136
C
Hardware Installation Guide
4
Contents
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
www.ti.com
List of Figures
2-1.
Signal Connections for 4-Wire JTAG Communication ................................................................ 25
2-2.
Signal Connections for 2-Wire JTAG Communication (Spy-Bi-Wire) ............................................... 26
B-1.
MSP-TS430PW14 Target Socket Module, Schematic
B-2.
MSP-TS430PW14 Target Socket Module, PCB
B-3.
B-4.
B-5.
B-6.
B-7.
B-8.
B-9.
B-10.
B-11.
B-12.
B-13.
B-14.
B-15.
B-16.
B-17.
B-18.
B-19.
B-20.
B-21.
B-22.
B-23.
B-24.
B-25.
B-26.
B-27.
B-28.
B-29.
B-30.
B-31.
B-32.
B-33.
B-34.
B-35.
B-36.
B-37.
B-38.
B-39.
B-40.
B-41.
B-42.
B-43.
B-44.
B-45.
............................................................... 34
...................................................................... 35
MSP-TS430L092 Target Socket Module, Schematic ................................................................. 37
MSP-TS430L092 Target Socket Module, PCB ........................................................................ 38
MSP-TS430L092 Active Cable Target Socket Module, Schematic ................................................. 40
MSP-TS430L092 Active Cable Target Socket Module, PCB ........................................................ 41
MSP-TS430PW24 Target Socket Module, Schematic ............................................................... 43
MSP-TS430PW24 Target Socket Module, PCB ...................................................................... 44
MSP-TS430DW28 Target Socket Module, Schematic ............................................................... 46
MSP-TS430DW28 Target Socket Module, PCB ...................................................................... 47
MSP-TS430PW28 Target Socket Module, Schematic ............................................................... 49
MSP-TS430PW28 Target Socket Module, PCB ...................................................................... 50
MSP-TS430PW28A Target Socket Module, Schematic .............................................................. 52
MSP-TS430PW28A Target Socket Module, PCB (Red) ............................................................. 53
MSP-TS430DA38 Target Socket Module, Schematic ................................................................ 55
MSP-TS430DA38 Target Socket Module, PCB ....................................................................... 56
MSP-TS430QFN23x0 Target Socket Module, Schematic ........................................................... 58
MSP-TS430QFN23x0 Target Socket Module, PCB .................................................................. 59
MSP-TS430RSB40 Target Socket Module, Schematic .............................................................. 61
MSP-TS430RSB40 Target Socket Module, PCB ..................................................................... 62
MSP-TS430RHA40A Target Socket Module, Schematic ............................................................ 64
MSP-TS430RHA40A Target Socket Module, PCB ................................................................... 65
MSP-TS430DL48 Target Socket Module, Schematic ................................................................ 67
MSP-TS430DL48 Target Socket Module, PCB ....................................................................... 68
MSP-TS430RGZ48B Target Socket Module, Schematic ............................................................ 70
MSP-TS430RGZ48B Target Socket Module, PCB ................................................................... 71
MSP-TS430PM64 Target Socket Module, Schematic ................................................................ 73
MSP-TS430PM64 Target Socket Module, PCB ....................................................................... 74
MSP-TS430PM64A Target Socket Module, Schematic .............................................................. 76
MSP-TS430PM64A Target Socket Module, PCB ..................................................................... 77
MSP-TS430RGC64B Target Socket Module, Schematic ............................................................ 79
MSP-TS430RGC64B Target Socket Module, PCB ................................................................... 80
MSP-TS430RGC64USB Target Socket Module, Schematic ........................................................ 82
MSP-TS430RGC64USB Target Socket Module, PCB ............................................................... 83
MSP-TS430PN80 Target Socket Module, Schematic ................................................................ 86
MSP-TS430PN80 Target Socket Module, PCB ....................................................................... 87
MSP-TS430PN80A Target Socket Module, Schematic .............................................................. 89
MSP-TS430PN80A Target Socket Module, PCB ..................................................................... 90
MSP-TS430PN80USB Target Socket Module, Schematic .......................................................... 92
MSP-TS430PN80USB Target Socket Module, PCB.................................................................. 93
MSP-TS430PZ100 Target Socket Module, Schematic ............................................................... 96
MSP-TS430PZ100 Target Socket Module, PCB ...................................................................... 97
MSP-TS430PZ100A Target Socket Module, Schematic ............................................................. 99
MSP-TS430PZ100A Target Socket Module, PCB ................................................................... 100
MSP-TS430PZ100B Target Socket Module, Schematic............................................................ 102
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
List of Figures
© 2009–2010, Texas Instruments Incorporated
5
www.ti.com
B-46. MSP-TS430PZ100B Target Socket Module, PCB ................................................................... 103
B-47. MSP-TS430PZ5x100 Target Socket Module, Schematic
..........................................................
105
B-48. MSP-TS430PZ5x100 Target Socket Module, PCB.................................................................. 106
B-49. MSP-TS430PZ100USB Target Socket Module, Schematic ........................................................ 108
B-50. MSP-TS430PZ100USB Target Socket Module, PCB ............................................................... 109
B-51. EM430F5137RF900 Target Socket Module, Schematic ............................................................ 112
B-52. EM430F5137RF900 Target Socket Module, PCB ................................................................... 113
B-53. EM430F6137RF900 Target Socket Module, Schematic ............................................................ 116
B-54. EM430F6137RF900 Target Socket Module, PCB ................................................................... 117
B-55. MSP-FET430PIF FET Interface Module, Schematic ................................................................ 120
B-56. MSP-FET430PIF FET Interface Module, PCB ....................................................................... 121
122
B-58. MSP-FET430UIF USB Interface, Schematic (2 of 4)
123
B-59.
124
B-60.
B-61.
C-1.
C-2.
C-3.
C-4.
C-5.
C-6.
C-7.
6
...............................................................
...............................................................
MSP-FET430UIF USB Interface, Schematic (3 of 4) ...............................................................
MSP-FET430UIF USB Interface, Schematic (4 of 4) ...............................................................
MSP-FET430UIF USB Interface, PCB ................................................................................
Windows XP Hardware Recognition...................................................................................
Windows XP Hardware Wizard ........................................................................................
Windows XP Driver Location Selection Folder .......................................................................
Windows XP Driver Installation ........................................................................................
Device Manager Using MSP-FET430UIF or eZ430-F2013 (CCE and CCS Only) ..............................
Device Manager Using MSP-FET430UIF or eZ430-F2013 (IAR Only) ...........................................
Device Manager Using eZ430-RF2500 (CCE/CCS and IAR) ......................................................
B-57. MSP-FET430UIF USB Interface, Schematic (1 of 4)
List of Figures
125
126
130
130
131
132
133
134
135
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
www.ti.com
List of Tables
..................................................................................
1-1.
Flash Emulation Tool (FET) Features
1-2.
Individual Kit Contents, MSP-TS430xx ................................................................................. 18
B-1.
MSP-TS430PW14 Bill of Materials ...................................................................................... 36
B-2.
MSP-TS430L092 Bill of Materials ....................................................................................... 39
B-3.
MSP-TS430L092 JP1 Settings .......................................................................................... 41
B-4.
MSP-TS430L092 Active Cable Bill of Materials ....................................................................... 42
B-5.
MSP-TS430PW24 Bill of Materials ...................................................................................... 45
B-6.
MSP-TS430DW28 Bill of Materials...................................................................................... 48
B-7.
MSP-TS430PW28 Bill of Materials
B-8.
MSP-TS430PW28A Bill of Materials .................................................................................... 54
B-9.
MSP-TS430DA38 Bill of Materials ...................................................................................... 57
.....................................................................................
14
51
B-10. MSP-TS430QFN23x0 Bill of Materials.................................................................................. 60
B-11. MSP-TS430RSB40 Bill of Materials
....................................................................................
63
B-12. MSP-TS430RHA40A Bill of Materials................................................................................... 66
B-13. MSP-TS430DL48 Bill of Materials ....................................................................................... 69
B-14. MSP-TS430RGZ48B Bill of Materials................................................................................... 72
B-15. MSP-TS430PM64 Bill of Materials ...................................................................................... 75
B-16. MSP-TS430PM64A Bill of Materials .................................................................................... 78
B-17. MSP-TS430RGC64B Bill of Materials .................................................................................. 81
B-18. MSP-TS430RGC64USB Bill of Materials............................................................................... 84
B-19. MSP-TS430PN80 Bill of Materials ...................................................................................... 88
....................................................................................
MSP-TS430PN80USB Bill of Materials .................................................................................
MSP-TS430PZ100 Bill of Materials .....................................................................................
MSP-TS430PZ100A Bill of Materials ..................................................................................
MSP-TS430PZ100B Bill of Materials ..................................................................................
MSP-TS430PZ5x100 Bill of Materials .................................................................................
MSP-TS430PZ100USB Bill of Materials ..............................................................................
EM430F5137RF900 Bill of Materials ..................................................................................
EM430F6137RF900 Bill of Materials ..................................................................................
B-20. MSP-TS430PN80A Bill of Materials
B-21.
B-22.
B-23.
B-24.
B-25.
B-26.
B-27.
B-28.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
List of Tables
© 2009–2010, Texas Instruments Incorporated
91
94
98
101
104
107
110
114
118
7
8
List of Tables
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Preface
SLAU278F – May 2009 – Revised December 2010
Read This First
About This Manual
This manual describes the hardware of the Texas Instruments MSP-FET430 Flash Emulation Tool (FET).
The FET is the program development tool for the MSP430 ultra-low-power microcontroller. Both available
interface types, the parallel port interface and the USB interface, are described.
How to Use This Manual
Read and follow the instructions in Chapter 1. This chapter lists the contents of the FET, provides
instructions on installing the hardware and according software drivers. After you see how quick and easy it
is to use the development tools, TI recommends that you read all of this manual.
This manual describes the setup and operation of the FET but does not fully describe the MSP430™
microcontrollers or the development software systems. For details of these items, see the appropriate TI
documents listed in Section 1.18.
This manual applies to the following tools (and devices):
• MSP-FET430PIF (debug interface with parallel port connection, for all MSP430 flash-based devices)
• MSP-FET430UIF (debug interface with USB connection, for all MSP430 flash-based devices)
• eZ430-F2013 (USB stick form factor interface with attached MSP430F2013 target, for all
MSP430F20xx, MSP430G2x01, MSP430G2x11, MSP430G2x21 and MSP430G2x31 devices)
• eZ430-T2012 (three MSP430F2012 based target boards)
• eZ430-RF2500 (USB stick form factor interface with attached MSP430F2274/CC2500 target, for all
MSP430F20xx, MSP430F21x2, MSP430F22xx, MSP430G2x01, MSP430G2x11, MSP430G2x21 and
MSP430G2x31 devices)
• eZ430-RF2500T (one MSP430F2274/CC2500 target board including battery pack)
• eZ430-RF2500-SEH (USB stick form factor interface with attached MSP430F2274/CC2500 target and
solar energy harvesting module)
• eZ430-Chronos-xxx (USB stick form factor interface with CC430F6137 based development system
contained in a watch. Includes <1 GHz RF USB access point)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Read This First
© 2009–2010, Texas Instruments Incorporated
9
How to Use This Manual
www.ti.com
The following tools contain the USB debug interface (MSP-FET430UIF) and the respective target socket
module:
• MSP-FET430U14 (for MSP430F20xx, MSP430F20xx, MSP430G2x01, MSP430G2x11, MSP430G2x21
and MSP430G2x31 devices in 14-pin PW packages)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
MSP-FET430U092 (for MSP430FL092 devices in 14-pin PW packages)
MSP-FET430U24 (for MSP430AFE2xx devices in 24-pin PW packages)
MSP-FET430U28 (for MSP430F11xx(A) devices in 20- and 28-pin DW or PW packages)
MSP-FET430U28A (for MSP430F20xx and MSP430G2xxx devices in 14-, 20-, and 28-pin PW)
MSP-FET430U38 (for MSP430F22x2 and MSP430F22x4 devices in 38-pin DA packages)
MSP-FET430U23x0 (for MSP430F23x0 devices in 40-pin RHA packages)
MSP-FET430U40 (for MSP430F51x1, MSP430F51x2 devices in 40-pin RSB packages)
MSP-FET430U40A (for MSP430FR572x, MSP430FR573x devices in 40-pin RHA packages)
MSP-FET430U48 (for MSP430F22x2 and MSP430F22x4 devices in 48-pin DL packages)
MSP-FET430U48B (for MSP430F534x devices in 48-pin RGZ packages)
MSP-FET430U64 (for MSP430F13x, MSP430F14x, MSP430F14x1, MSP430F15x, MSP430F16x(1),
MSP430F23x, MSP430F24x, MSP430F24xx, MSP430F261x, MSP430F41x, MSP430F42x(A),
MSP430FE42x(A), MSP430FE42x2, and MSP430FW42x devices in 64-pin PM packages)
MSP-FET430U64A (for MSP430F41x2 devices in 64-pin PM packages)
MSP-FET430U64B (for MSP430F530x devices in 64-pin RGC packages)
MSP-FET430U64USB (for MSP430F550x, MSP430F551x, MSP430552x, devices in 64-pin RGC
packages
MSP-FET430U80 (for MSP430F241x, MSP430F261x, MSP430F43x, MSP430F43x1, MSP430FG43x,
MSP430F47x, and MSP430FG47x devices in 80-pin PN packages)
MSP-FET430U80A (for MSP430F532x devices in 80-pin PN packages)
MSP-FET430U80USB (for MSP430F552x devices with USB peripheral in 80-pin PN packages)
MSP-FET430U100 (for MSP430F43x, MSP430F43x1, MSP430F44x, MSP430FG461x, and
MSP430F47xx devices in 100-pin PZ packages)
MSP-FET430U100A (for MSP430F471xx devices in 100-pin PZ packages - red PCB)
MSP-FET430U5x100 (for MSP430F54xx(A) devices and the MSP430BT5190 in 100-pin PZ packages)
MSP-FET430U100USB (for MSP430F663x and MSP430F563x devices in 100-pin PZ packages)
FET430F5137RF900 (for CC430F513x devices in 48-pin RGZ packages)
FET430F6137RF900 (for CC430F612x and CC430F613x devices in 64-pin RGC packages)
Stand-alone target-socket modules (without debug interface):
• MSP-TS430PW14 (for MSP430F20xx, MSP430G2x01, MSP430G2x11, MSP430G2x21 and
MSP430G2x31 devices in 14-pin PW packages)
• MSP-TS430L092 (for MSP430FL092 devices in 14-pin PW packages)
• MSP-TS430PW24 (for MSP430AFE2xx devices in 24-pin PW packages)
• MSP-TS430DW28 (for MSP430F11xx(A) devices in 28-in DW packages)
• MSP-TS430PW28 (for MSP430F11xx(A) devices in 28-in PW packages)
• MSP-TS430PW28A (for MSP430F20xx and MSP430G2xxx devices in 14, 20 and 28-pin PW)
• MSP-TS430DA38 (for MSP430F22x2 and MSP430F22x4 devices in 38-pin DA packages)
• MSP-TS430QFN23x0 (for MSP430F23x0 devices in 40-pin RHA packages)
• MSP-TS430RSB40 (for MSP430F51x1, MSP430F51x2 devices in 40-pin RSB packages)
• MSP-TS430RHA40A ((for MSP430FR572x, MSP430FR573x devices in 40-pin RHA packages)
• MSP-TS430DL48 (for MSP430F22x2 and MSP430F22x4 devices in 48-pin DL packages)
• MSP-TS430RGZ48B (for MSP430F534x devices in 48-pin RGZ packages)
• MSP-TS430PM64 (for MSP430F13x, MSP430F14x, MSP430F14x1, MSP430F15x, MSP430F16x(1),
MSP430F23x, MSP430F24x, MSP430F24xx, MSP430F261x, MSP430F41x, MSP430F42x(A),
MSP430FE42x(A), MSP430FE42x2, and MSP430FW42x devices in 64-pin PM packages)
• MSP-TS430PM64A (for MSP430F41x2 devices in 64-pin PM packages)
10
Read This First
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Information About Cautions and Warnings
www.ti.com
•
•
•
•
MSP-TS430RGC64B (for MSP430F530x devices in 64-pin RGC packages)
MSP-TS430RGC64USB (for MSP430F550x, MSP430F551x, MSP430552x, devices in 64-pin RGC
packages)
MSP-TS430PN80 (for MSP430F241x, MSP430F261x, MSP430F43x, MSP430F43x1, MSP430FG43x,
MSP430F47x, and MSP430FG47x devices in 80-pin PN packages)
MSP-TS430PN80A (for MSP430F532x devices in 80-pin PN packages)
MSP-TS430PN80USB (for MSP430F552x devices with USB peripheral in 80-pin PN packages)
MSP-TS430PZ100 (for MSP430F43x, MSP430F43x1, MSP430F44x, MSP430FG461x, and
MSP430F47xx devices in 100-pin PZ packages)
MSP-TS430PZ100A (for MSP430F471xx devices in 100-pin PZ packages — red PCB)
MSP-TS430PZ5x100 (for MSP430F54xx(A) and the MSP430BT5190 devices in 100-pin PZ packages)
•
•
•
MSP-TS430PZ100USB (for MSP430F663x and MSP430F563x devices in 100-pin PZ packages)
EM430F5137RF900 (with integrated CC430F5137 IC in a 48-pin RGZ package)
EM430F6137RF900 (with integrated CC430F6137 IC in a 64-pin RGC package)
•
•
•
•
These tools contain the most up-to-date materials available at the time of packaging. For the latest
materials (data sheets, user's guides, software, application information, etc.), visit the TI MSP430 web site
at www.ti.com/msp430 or contact your local TI sales office.
Information About Cautions and Warnings
This document may contain cautions and warnings.
CAUTION
This is an example of a caution statement.
A caution statement describes a situation that could potentially damage your
software or equipment.
WARNING
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection. Read each caution and warning
carefully.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Read This First
© 2009–2010, Texas Instruments Incorporated
11
Related Documentation From Texas Instruments
www.ti.com
Related Documentation From Texas Instruments
MSP430 development tools documentation:
CCS for MSP430 User's Guide, literature number SLAU157
Code Composer Studio v4.x Core Edition, CCS Mediawiki
IAR for MSP430 User's Guide, literature number SLAU138
IAR Embedded Workbench KickStart, SLAC050
eZ430-F2013 Development Tool User's Guide, literature number SLAU176
eZ430-RF2480 User's Guide, literature number SWRA176
eZ430-RF2500 Development Tool User's Guide, literature number SLAU227
eZ430-RF2500-SEH Development Tool User's Guide, literature number SLAU273
eZ430-Chronos Development Tool User's Guide, literature number SLAU292
MSP430xxxx device user's guides:
MSP430x1xx Family User's Guide, literature number SLAU049
MSP430x2xx Family User's Guide, literature number SLAU144
MSP430x3xx Family User's Guide, literature number SLAU012
MSP430x4xx Family User's Guide, literature number SLAU056
MSP430x5xx Family User's Guide, literature number SLAU208
CC430 Family User's Guide, literature number SLAU259
If You Need Assistance
Support for the MSP430 devices and the FET development tools is provided by the Texas Instruments
Product Information Center (PIC). Contact information for the PIC can be found on the TI web site at
www.ti.com/support. The Texas Instruments E2E Community support forums for the MSP430 provide
open interaction with peer engineers, TI engineers, and other experts. Additional device-specific
information can be found on the MSP430 web site.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It generates, uses, and can
radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable
protection against radio-frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case, the user is required to take whatever
measures may be required to correct this interference at his own expense.
12
Read This First
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Chapter 1
SLAU278F – May 2009 – Revised December 2010
Get Started Now!
This chapter lists the contents of the FET and provides instruction on installing the hardware.
Topic
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.18
...........................................................................................................................
Flash Emulation Tool (FET) Overview ..................................................................
Kit Contents, MSP-FET430PIF .............................................................................
Kit Contents, eZ430-F2013 ..................................................................................
Kit Contents, eZ430-T2012 ..................................................................................
Kit Contents, eZ430-RF2500 ................................................................................
Kit Contents, eZ430-RF2500T ..............................................................................
Kit Contents, eZ430-RF2500-SEH ........................................................................
Kit Contents, eZ430-Chronos-xxx ........................................................................
Kit Contents, MSP-FET430UIF .............................................................................
Kit Contents, MSP-FET430xx ..............................................................................
Kit Contents, FET430Fx137RF900 ........................................................................
Kit Contents, MSP-TS430xx ................................................................................
Kit Contents, EM430Fx137RF900 .........................................................................
Hardware Installation, MSP-FET430PIF ................................................................
Hardware Installation, MSP-FET430UIF ................................................................
Hardware Installation, eZ430-F2013, eZ430-RF2500, eZ430-Chronos ........................
Hardware Installation, MSP-FET430Uxx, MSP-TS430xxx, FET430Fx137RF900,
EM430Fx137RF900 ............................................................................................
Important MSP430 Documents on the CD-ROM and Web .......................................
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Get Started Now!
© 2009–2010, Texas Instruments Incorporated
Page
14
14
14
14
15
15
15
15
15
16
17
17
19
19
20
20
20
21
13
Flash Emulation Tool (FET) Overview
1.1
www.ti.com
Flash Emulation Tool (FET) Overview
TI offers several flash emulation tools according to different requirements.
Table 1-1. Flash Emulation Tool (FET) Features
eZ430-F2013
eZ430-RF2500
eZ430-Chronos
MSPFET430UIF
MSP-FET430PIF
X
X
Supports all MSP430 and CC430
flash-based devices ('F1xx, 'F2xx,
'F4xx, 'F5xx, 'F6xx, 'G2xx, 'L092)
Supports only 'F20xx, 'G2x01,
'G2x11, 'G2x21, 'G2x31
X
Supports only MSP430F20xx,
'F21x2, 'F22xx, 'G2x01, 'G2x11,
'G2x21, 'G2x31
X
Supports only
CC430F51xx, 'F61xx,
MSP430F20xx, 'F21x2, 'F22xx,
'F41x2, 'F54xx, 'F54xxA, 'F55xx
X
Allows fuse blow
X
Adjustable target supply voltage
X
Fixed 2.8-V target supply voltage
X
Fixed 3.6-V target supply voltage
X
X
X
X
X
X
X
X
4-wire JTAG
X
2-wire JTAG (1)
Application UART
Supported by CCE
X
X
Supported by CCS
X
X
Supported by IAR
X
X
(1)
(2)
1.2
X
X
X (2)
X
X
X
The 2-wire JTAG debug interface is also referred to as Spy-Bi-Wire (SBW) interface.
Not supported by default. Driver installation needs to be selected manually during the CCS installation process.
One
One
One
One
One
READ ME FIRST document
MSP430 CD-ROM
MSP-FET430PIF interface module
25-conductor cable
14-conductor cable
One QUICK START GUIDE document
One eZ430-F2013 CD-ROM
One eZ430-F2013 development tool including one MSP430F2013 target board
Kit Contents, eZ430-T2012
•
14
X
Kit Contents, eZ430-F2013
•
•
•
1.4
X
Kit Contents, MSP-FET430PIF
•
•
•
•
•
1.3
X
X
Three MSP430F2012-based target boards
Get Started Now!
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Kit Contents, eZ430-RF2500
www.ti.com
1.5
Kit Contents, eZ430-RF2500
•
•
•
•
•
1.6
One eZ430-RF2500T target board
One AAA battery pack with expansion board (batteries included)
Kit Contents, eZ430-RF2500-SEH
•
•
•
•
•
1.8
QUICK START GUIDE document
eZ430-RF2500 CD-ROM
eZ430-RF2500 development tool including one MSP430F2274/CC2500 target board
eZ430-RF2500T target board
AAA battery pack with expansion board (batteries included)
Kit Contents, eZ430-RF2500T
•
•
1.7
One
One
One
One
One
One MSP430 development tool CD containing documentation and development software
One eZ430-RF USB debugging interface
Two eZ430-RF2500T wireless target boards
One SEH-01 solar energy harvester board
One AAA battery pack with expansion board (batteries included)
Kit Contents, eZ430-Chronos-xxx
'433, '868, '915
• One QUICK START GUIDE document
• One eZ430-Chronos CD-ROM
• One ez430-Chronos emulator
• One screwdriver
• Two spare screws
eZ430-Chronos-433:
– One 433-MHz eZ430-Chronos watch (battery included)
– One 433-MHz eZ430-Chronos access point
eZ430-Chronos-868:
– One 868-MHz eZ430-Chronos watch (battery included)
– One 868-MHz eZ430-Chronos access point
eZ430-Chronos-915:
– One 915-MHz eZ430-Chronos watch (battery included)
– One 915-MHz eZ430-Chronos access point
1.9
Kit Contents, MSP-FET430UIF
•
•
•
•
•
One
One
One
One
One
READ ME FIRST document
MSP430 CD-ROM
MSP-FET430UIF interface module
USB cable
14-conductor cable
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Get Started Now!
© 2009–2010, Texas Instruments Incorporated
15
Kit Contents, MSP-FET430xx
www.ti.com
1.10 Kit Contents, MSP-FET430xx
'U14, 'U092, 'U24, 'U28, 'U28A, 'U38, 'U23x0, 'U40, 'U40A, 'U48, 'U48B, 'U64, 'U64A, 'U64USB, 'U80,
'U80USB, 'U100, 'U100A, 'U100B, 'U5x100, 'U100USB
• One READ ME FIRST document
• One MSP430 CD-ROM
• One MSP-FET430UIF USB interface module. This is the unit that has a USB B-connector on one end
of the case, and a 2×7-pin male connector on the other end of the case.
• One USB cable
• One 32.768-kHz crystal from Micro Crystal (except MSP-FET430U24)
• A 2×7-pin male JTAG connector is also present on the PCB (see different setup for L092)
• One 14-Pin JTAG conductor cable
• One small box containing two MSP430 device samples (See table for Sample Type)
• One target socket module. To check the devices used for each board and a summary of the board,
see Table 1-2. MSP-TS430xx below is the target socket module for each MSP-FET430Uxx kit.
MSP-FET430U14: One MSP-TS430PW14 target socket module.
MSP-FET430U092: One MSP-TS430L092 target socket module with Active Cable.
MSP-FET430U24: One MSP-TS430PW24 target socket module.
MSP-FET430U28: One MSP-TS430PW28 target socket module.
MSP-FET430U28A: One MSP-TS430PW28A target socket module.
MSP-FET430U38: One MSP-TS430DA38 target socket module..
MSP-FET430U23x0: One MSP-TS430QFN23x0 (former name MSP-TS430QFN40) target socket
module.
MSP-FET430U40: One MSP-TS430RSB40 target socket module.
MSP-FET430U48: One MSP-TS430DL48 target socket module.
MSP-FET430U48B: One MSP-TS430RGZ48B target socket module.
MSP-FET430U64: One MSP-TS430PM64 target socket module.
MSP-FET430U64A: One MSP-TS430PM64A target socket module.
MSP-FET430U64B: One MSP-TS430RGC64B target socket module.
MSP-FET430U64USB: One MSP-TS430RGC64USB target socket module.
MSP-FET430U80: One MSP-TS430PN80 target socket module.
MSP-FET430U80A: One MSP-TS430PN80A target socket module.
MSP-FET430U80USB: One MSP-TS430PN80USB target socket module.
MSP-FET430U100: One MSP-TS430PZ100 target socket module.
MSP-FET430U100A: One MSP-TS430PZ100A target socket module
MSP-FET430U100B: One MSP-TS430PZ100B target socket module
MSP-FET430U5x100: One MSP-TS430PZ5x100 target socket module.
MSP-FET430U100USB: One MSP-TS430PZ100USB target socket module.
Consult the device data sheets for device specifications. Device errata can be found in the respective
device product folder on the web provided as a PDF document. Depending on the device, errata may also
be found in the device bug database at www.ti.com/sc/cgi-bin/buglist.cgi.
16
Get Started Now!
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Kit Contents, FET430Fx137RF900
www.ti.com
1.11 Kit Contents, FET430Fx137RF900
•
•
•
•
•
•
•
•
•
•
•
•
One READ ME FIRST document
One legal notice
One MSP430 CD-ROM
One MSP-FET430UIF interface module
Two target socket module
MSP-FET430F5137RF900: Two EM430F5137RF900 target socket modules. This is the PCB on which
is soldered a CC430F5137 device in a 48-pin RGZ package. A 2×7-pin male connector is also present
on the PCB
MSP-FET430F6137RF900: Two EM430F6137RF900 target socket modules. This is the PCB on which
is soldered a CC430F6137 device in a 64-pin RGC package. A 2×7-pin male connector is also present
on the PCB
Two CC430EM battery packs
Four AAA batteries
Two 868-/915-MHz antennas
Two 32.768-kHz crystals
18 PCB 2x4-pin headers
One USB cable
One 14-Pin JTAG conductor cable
1.12 Kit Contents, MSP-TS430xx
'PW14, 'L092, 'PW24, 'DW28, 'PW28, 'PW28A, 'DA38, 'QFN32x0, 'RSB40, 'DL48, 'RGZ48B, 'PM64,
'PM64A, 'RGC64B, 'RGC64USB, 'PN80, 'PN80A, 'PN80USB, 'PZ100, 'PZ100A, 'PZ100B, 'PZ5x100,
'PZ100USB
• One READ ME FIRST document
• One MSP430 CD-ROM
• One 32.768-kHz crystal from Micro Crystal (except MSP-TS430PW24)
• One target socket module
• A 2×7-pin male JTAG connector is also present on the PCB (see different setup for L092)
• One small box containing two MSP430 device samples (See table for Sample Type)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Get Started Now!
© 2009–2010, Texas Instruments Incorporated
17
Kit Contents, MSP-TS430xx
www.ti.com
Table 1-2. Individual Kit Contents, MSP-TS430xx
18
Target Socket
Module
Socket Type
Supported Devices
MSP-TS430PW14
14-pin PW
(TSSOP ZIF)
MSP430F20xx, 'G2x01,
'G2x11, 'G2x21, 'G2x31
Included Devices
Headers / Comment
2 x MSP430F2013IPW
Four PCB 1×7-pin headers (two
male and two female
MSP-TS430L092
14-pin PW
(TSSOP ZIF)
MSP-TS430L092
2 x MSP430L092IPW
Four PCB 1×7-pin headers (two
male and two female). A
"Micro-MaTch" 10-pin female
connector is also present on the
PCB which connects the kit with an
'Active Cable' PCB, this 'Active
Cable' PCB is connected by 14 Pin
JTAG cable with the FET430UIF
MSP-TS430PW24
24-pin PW
(TSSOP ZIF)
MSP430AFE2xx
2 x MSP430AFE253IPW
Four PCB 1×12-pin headers (two
male and two female
MSP-TS430DW28
28-pin DW
(SSOP ZIF)
MSP-TS430PW28
MSP430F11x1, 'F11x2,
'F12x 'F12x2 'F21xx.
2 x MSP430F123IDW
Supports devices in 20and 28-pin DA packages
Four PCB 1×12-pin headers (two
male and two female
28-pin PW
(TSSOP ZIF)
MSP430F11x1, 'F11x2,
'F12x, 'F12x2, 'F21xx
2 x MSP430F2132IPW
Four PCB 1×12-pin headers (two
male and two female
MSP-TS430PW28A
28-pin PW
(TSSOP ZIF)
MSP430F20xx,
MSP430G2xxx in 14-,
20-, and 28-pin PW
packages
2x
MSP430G2452IPW28
Four PCB 1×12-pin headers (two
male and two female
MSP-TS430DA38
38-pin DA
(TSSOP ZIF)
MSP430F22xx
2 x MSP430F2274IDA
Four PCB 1×19-pin headers (two
male and two female
MSPTS430QFN23x0
40-pin RHA
(QFN ZIF)
MSP430F23x0
2 x MSP430F2370IRHA
Eight PCB 1×10-pin headers (four
male and four female
MSP-TS430RSB40
40-pin RSB
(QFN ZIF)
MSP430F51x1, 'F51x2
2 x MSP430F5172IRSB
Eight PCB 1×10-pin headers (four
male and four female
MSP-TS430RHA40A
40-pin RHA
(QFN ZIF)
MSP430FR572x,
'FR573x
2x
MSP430FR5739IRHA
Eight PCB 1×10-pin headers (four
male and four female
MSP-TS430DL48
48-pin DL
(TSSOP ZIF)
MSP430F42x0
2 x MSP430F4270IDL
Four PCB 2×12-pin headers (two
male and two female
MSP-TS430RGZ48B
48-pin RGZ
(QFN ZIF)
MSP430F534x
2 x MSP430F5342IRGZ
Eight PCB 1×12-pin headers (four
male and four female
MSP-TS430PM64
64-pin PM
(QFP ZIF)
MSP430F13x, 'F14x,
'F14x1, 'F15x, 'F16x(1),
'F23x, 'F24x, 'F24xx,
'F261x, 'F41x, 'F42x(A),
'FE42x(A), 'FE42x2,
'FW42x
TS Kit: 2 x
MSP430F2618IPM;
FET Kit: 2 x
MSP430F417IPM and 2
x MSP430F169IPM
Eight PCB 1×16-pin headers (four
male and four female
MSP-TS430PM64A
64-pin PM
(QFP ZIF)
MSP430F41x2
2 x MSP430F4152IPM
Eight PCB 1×16-pin headers (four
male and four female
MSPTS430RGC64B
64-pin RGC
(QFN ZIF)
MSP430F530x
2 x MSP430F5310IRGC
Eight PCB 1×16-pin headers (four
male and four female
MSPTS430RGC64USB
64-pin RGC
(QFN ZIF)
MSP430F550x, 'F551x,
'F552x
2 x MSP430F5510IRGC
and/or 2 x
MSP430F5528IRGC
Eight PCB 1×16-pin headers (four
male and four female
MSP-TS430PN80
80-pin PN
(QFP ZIF)
MSP430F241x, 'F261x,
'F43x, 'F43x1, 'FG43x,
'F47x, 'FG47x
2 x MSP430FG439IPN
Eight PCB 1×20-pin headers (four
male and four female
MSP-TS430PN80A
80-pin PN
(QFP ZIF)
MSP430F532x
2 x MSP430F5329IPN
Eight PCB 1×20-pin headers (four
male and four female
MSPTS430PN80USB
80-pin PN
(QFP ZIF)
MSP430F552x, 'F551x
2 x MSP430F5529IPN
Eight PCB 1×20-pin headers (four
male and four female
MSP-TS430PZ100
100-pin PZ
(QFP ZIF)
MSP430F43x, 'F43x1,
'F44x, 'FG461x, 'F47xx
2 x MSP430FG4619IPZ
Eight PCB 1×25-pin headers (four
male and four female
MSP-TS430PZ100A
100-pin PZ
(QFP ZIF)
MSP430F471xx
2 x MSP430F47197IPZ
Eight PCB 1×25-pin headers (four
male and four female
Get Started Now!
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Kit Contents, EM430Fx137RF900
www.ti.com
Table 1-2. Individual Kit Contents, MSP-TS430xx (continued)
Target Socket
Module
Socket Type
Supported Devices
MSP-TS430PZ100B
100-pin PZ
(QFP ZIF)
MSP430F67xx
MSPTS430PZ5x100
MSPTS430PZ100USB
Included Devices
Headers / Comment
2 x MSP430F6733IPZ
Eight PCB 1×25-pin headers (four
male and four female
100-pin PZ
(QFP ZIF)
MSP430F543x,MSP430
2 x MSP430F5438IPZ
BT5190IPZ
Eight PCB 1×25-pin headers (four
male and four female
100-pin PZ
(QFP ZIF)
MSP430F663x, 'F563x
Eight PCB 1×25-pin headers (four
male and four female
2 x MSP430F6638IPZ
See the device data sheets for device specifications. Device errata can be found in the respective device
product folder on the web provided as a PDF document. Depending on the device, errata may also be
found in the device bug database at www.ti.com/sc/cgi-bin/buglist.cgi.
1.13 Kit Contents, EM430Fx137RF900
•
•
•
•
•
•
•
•
•
One READ ME FIRST document
One legal notice
One MSP430 CD-ROM
Two target socket module
MSP-EM430F5137RF900: Two EM430F5137RF900 target socket modules. This is the PCB on which
is soldered a CC430F5137 device in a 48-pin RGZ package. A 2×7-pin male connector is also present
on the PCB
MSP-EM430F6137RF900: Two EM430F6137RF900 target socket modules. This is the PCB on which
is soldered a CC430F6137 device in a 64-pin RGC package. A 2×7-pin male connector is also present
on the PCB
Two CC430EM battery packs
Four AAA batteries
Two 868-/915-MHz antennas
Two 32.768-kHz crystals
18 PCB 2×4-pin headers
1.14 Hardware Installation, MSP-FET430PIF
Follow these steps to install the hardware for the MSP-FET430PIF tools:
1. Use the 25-conductor cable to connect the FET interface module to the parallel port of the PC. The
necessary driver for accessing the PC parallel port is installed automatically during CCE/CCS or IAR
Embedded Workbench installation. Note that a restart is required after the CCE/CCS or IAR
Embedded Workbench installation for the driver to become active.
2. Use the 14-conductor cable to connect the parallel-port debug interface module to a target board, such
as an MSP-TS430xxx target socket module. Module schematics and PCBs are shown in Appendix B.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Get Started Now!
© 2009–2010, Texas Instruments Incorporated
19
Hardware Installation, MSP-FET430UIF
www.ti.com
1.15 Hardware Installation, MSP-FET430UIF
Follow these steps to install the hardware for the MSP-FET430UIF tool:
1. Use the USB cable to connect the USB-FET interface module to a USB port on the PC. The USB FET
should be recognized, as the USB device driver should have been installed with the IDE (Code
Composer Essentials/Studio or IAR Embedded Workbench).. If the install wizard starts, follow the
prompts and point the wizard to the driver files.
The default location for CCE is C:\Program Files\Texas Instruments\MSP430_USB_DRIVERS_v3\.
The default location for CCS is C:\Program Files\Texas Instruments\ccs4\emulation\drivers\msp430\.
The default location for IAR Embedded Workbench is <Installation Root>\Embedded Workbench x.x\
430\bin\WinXP.
Detailed driver installation instructions can be found in Appendix C.
2. After connecting to a PC, the USB FET performs a self-test during which the red LED flashes for
approximately two seconds. If the self-test passes successfully, the green LED stays on.
3. Use the 14-conductor cable to connect the USB-FET interface module to a target board, such as an
MSP-TS430xxx target socket module.
4. Ensure that the MSP430 device is securely seated in the socket, and that its pin 1 (indicated with a
circular indentation on the top surface) aligns with the "1" mark on the PCB.
5. Compared to the parallel-port debug interface, the USB FET has additional features including JTAG
security fuse blow and adjustable target VCC (1.8 V to 3.6 V). Supply the module with up to 100 mA.
1.16 Hardware Installation, eZ430-F2013, eZ430-RF2500, eZ430-Chronos
Follow these steps to install the hardware for the eZ430-F2013 and eZ430-RF2500 tools:
1. Connect the eZ430-F2013, eZ430-RF2500 and eZ430-Chronos to a USB port of the PC.
2. The USB FET should be recognized by the PC. The USB device driver should have been installed with
the IDE (Code Composer Studio or IAR Embedded Workbench - Code Composer Essentials only
supports eZ430-F2013 and eZ430-RF2500). If the install wizard starts, follow the prompts and point
the wizard to the driver files.
The default location for CCE is C:\Program Files\Texas Instruments\MSP430_USB_DRIVERS_v3\.
The default location for CCS is C:\Program Files\Texas Instruments\ccs4\emulation\drivers\msp430\.
The default location for IAR Embedded Workbench is <Installation Root>\Embedded Workbench x.x\
430\bin\WinXP.
Detailed driver installation instructions can be found in Appendix C.
1.17 Hardware Installation, MSP-FET430Uxx, MSP-TS430xxx, FET430Fx137RF900,
EM430Fx137RF900
MSP-FET430Uxx – 'U14, 'U092, ,U24, 'U28, 'U28A, 'U38, 'U23x0, 'U40, 'U40A, 'U48, 'U48B, 'U64,
'U64A, 'U64USB, 'U80, 'U80USB, 'U100, 'U100A, 'U100B, 'U5x100, 'U100USB
TS430xxx – 'PW14, 'L092, 'PW24, 'DW28, 'PW28, 'PW28A, 'DA38, 'QFN32x0, 'RSB40, 'DL48,
'RGZ48B, 'PM64, 'PM64A, 'RGC64B, 'RGC64USB, 'PN80, 'PN80A, 'PN80USB, 'PZ100, 'PZ100A,
'PZ100B, 'PZ5x100, 'PZ100USB
Follow these steps to install the hardware for the MSP-FET430Uxx and MSP-TS430xxx tools:
1. Connect the MSP-FET430PIF or MSP-FET430UIF debug interface to the appropriate port of the PC.
Use the 14-conductor cable to connect the FET interface module to the supplied target socket module.
2. Ensure that the MSP430 device is securely seated in the socket and that its pin 1 (indicated with a
circular indentation on the top surface) aligns with the "1" mark on the PCB.
3. Ensure that the two jumpers (LED and VCC) near the 2×7-pin male connector are in place. Illustrations
of the target socket modules and their parts are found in Appendix B.
NOTE: Regarding 'U38, see FAQ Hardware #2 in Appendix A.
20
Get Started Now!
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
www.ti.com
Important MSP430 Documents on the CD-ROM and Web
1.18 Important MSP430 Documents on the CD-ROM and Web
The primary sources of MSP430 information are the device-specific data sheet and user's guide. The most
up-to-date versions of these documents that are available at the time of production are provided on the
CD-ROM included with this tool. The MSP430 web site (www.ti.com/msp430) contains the most recent
version of these documents.
PDF documents describing the CCS tools (CCS IDE, the assembler, the C compiler, the linker, and the
librarian) are in the msp430\documentation folder. A Code Composer Studio specific Wiki page (FAQ) is
available, and the Texas Instruments E2E Community support forums for the MSP430 and Code
Composer Studio v4 provide additional help besides the product help and Welcome page.
PDF documents describing the IAR tools (Workbench/C-SPY, the assembler, the C compiler, the linker,
and the librarian) are in the common\doc and 430\doc folders. Supplements to the documents (i.e., the
latest information) are available in HTML format in the same directories. 430\doc\readme_start.htm
provides a convenient starting point for navigating the IAR documentation.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Get Started Now!
© 2009–2010, Texas Instruments Incorporated
21
22
Get Started Now!
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Chapter 2
SLAU278F – May 2009 – Revised December 2010
Design Considerations for In-Circuit Programming
This chapter presents signal requirements for in-circuit programming of the MSP430.
Topic
2.1
2.2
2.3
...........................................................................................................................
Page
Signal Connections for In-System Programming and Debugging ............................ 24
External Power .................................................................................................. 27
Bootstrap Loader (BSL) ..................................................................................... 27
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
23
Signal Connections for In-System Programming and Debugging
2.1
www.ti.com
Signal Connections for In-System Programming and Debugging
MSP-FET430PIF, MSP-FET430UIF, MSP-GANG430, MSP-PRGS430
With the proper connections, the debugger and an FET hardware JTAG interface (such as the
MSP-FET430PIF and MSP-FET430UIF) can be used to program and debug code on the target board. In
addition, the connections also support the MSP-GANG430 or MSP-PRGS430 production programmers,
thus providing an easy way to program prototype boards, if desired.
Figure 2-1 shows the connections between the 14-pin FET interface module connector and the target
device required to support in-system programming and debugging for 4-wire JTAG communication.
Figure 2-2 shows the connections for 2-wire JTAG mode (Spy-Bi-Wire). While 4-wire JTAG mode is
supported on all MSP430 devices, 2-wire JTAG mode is available on selected devices only. See the CCS
User's Guide for MSP430 (SLAU157) or IAR for MSP430 User's Guide (SLAU138) for information on
which interface method can be used on which device.
The connections for the FET interface module and the MSP-GANG430 or MSP-PRGS430 are identical.
Both the FET interface module and MSP-GANG430 can supply VCC to the target board (via pin 2). In
addition, the FET interface module and MSP-GANG430 have a VCC-sense feature that, if used, requires
an alternate connection (pin 4 instead of pin 2). The VCC-sense feature senses the local VCC present on the
target board (i.e., a battery or other local power supply) and adjusts the output signals accordingly. If the
target board is to be powered by a local VCC, then the connection to pin 4 on the JTAG should be made,
and not the connection to pin 2. This utilizes the VCC-sense feature and prevents any contention that might
occur if the local on-board VCC were connected to the VCC supplied from the FET interface module or the
MSP-GANG430. If the VCC-sense feature is not necessary (i.e., the target board is to be powered from the
FET interface module or the GANG430) the VCC connection is made to pin 2 on the JTAG header and no
connection is made to pin 4. Figure 2-1 and Figure 2-2 show a jumper block that supports both scenarios
of supplying VCC to the target board. If this flexibility is not required, the desired VCC connections may be
hard-wired eliminating the jumper block. Pins 2 and 4 must not be connected simultaneously.
Note that in 4-wire JTAG communication mode (see Figure 2-1), the connection of the target RST signal
to the JTAG connector is optional when using devices that support only 4-wire JTAG communication
mode. However, when using devices that support 2-wire JTAG communication mode in 4-wire JTAG
mode, the RST connection must be made. The MSP430 development tools and device programmers
perform a target reset by issuing a JTAG command to gain control over the device. However, if this is
unsuccessful, the RST signal of the JTAG connector may be used by the development tool or device
programmer as an additional way to assert a device reset.
24
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Signal Connections for In-System Programming and Debugging
www.ti.com
VCC
J1 (see Note A)
VCC/AVCC/DVCC
J2 (see Note A)
R1
47 kW
(see Note B)
C2
10 µF
C3
0.1 µF
MSP430Fxxx
JTAG
VCC TOOL
VCC TARGET
TEST/VPP
RST/NMI
2
1
4
3
6
5
8
7
10
9
12
11
14
13
TDO/TDI
TDO/TDI
TDI/VPP
TDI/VPP
TMS
TMS
TCK
TCK
GND
RST (see Note D)
TEST/VPP (see Note C)
C1
10 nF/2.2 nF
(see Notes B and E)
VSS/AVSS/DVSS
A
Make either connection J1 in case a local target power supply is used or connection J2 to power target from the
debug/programming adapter.
B
The RST/NMI pin R1/C1 configuration is device family dependent. See the respective MSP430 family user's guide for
the recommended configuration.
C
The TEST pin is available only on MSP430 family members with multiplexed JTAG pins. See the device-specific data
sheet to determine if this pin is available.
D
The connection to the JTAG connector RST pin is optional when using 4-wire JTAG communication mode
capable-only devices and not required for device programming or debugging. However, this connection is required
when using 2-wire JTAG communication mode capable devices in 4-wire JTAG mode.
E
When using 2-wire JTAG communication capable devices in 4-wire JTAG mode, the upper limit for C1 should not
exceed 2.2 nF. This applies to both TI FET interface modules (LPT/USB FET).
Figure 2-1. Signal Connections for 4-Wire JTAG Communication
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
25
Signal Connections for In-System Programming and Debugging
www.ti.com
VCC
J1 (see Note A)
VCC/AVCC/DVCC
J2 (see Note A)
R1
47 kW
(see Note B)
C2
10 µF
C3
0.1 µF
MSP430Fxxx
JTAG
VCC TOOL
VCC TARGET
TEST/VPP
2
1
4
3
6
5
8
7
10
9
12
11
14
13
TDO/TDI
RST/NMI/SBWTDIO
TCK
GND
R2
330 W
(see Note C)
TEST/SBWTCK
C1
2.2 nF
(see Note B)
VSS/AVSS/DVSS
A
Make either connection J1 in case a local target power supply is used or connection J2 to power target from the
debug/programming adapter.
B
The device RST/NMI/SBWTDIO pin is used in 2-wire mode for bidirectional communication with the device during
JTAG access and that any capacitance attached to this signal may affect the ability to establish a connection with the
device. The upper limit for C1 is 2.2 nF when using current TI FET interface modules (USB FET).
C
R2 protects the JTAG debug interface TCK signal from the JTAG security fuse blow voltage that is supplied by the
TEST/VPP pin during the fuse blow process. If fuse blow functionality is not needed, R2 is not required (populate
0 ?), and do not connect TEST/VPP to TEST/SBWTCK.
Figure 2-2. Signal Connections for 2-Wire JTAG Communication (Spy-Bi-Wire)
26
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
External Power
www.ti.com
2.2
External Power
The PC parallel port can source a limited amount of current. Because of the ultra-low-power requirement
of the MSP430, a standalone FET does not exceed the available current. However, if additional circuitry is
added to the tool, this current limit could be exceeded. In this case, external power can be supplied to the
tool via connections provided on the target socket modules. See the schematics and pictorials of the
target socket modules in Appendix B to locate the external power connectors.
The MSP-FET430UIF can supply targets with up to 100 mA through pin 2 of the 14-pin connector. VCC for
the target can be selected between 1.8 V and 5 V in steps of 0.1 V. Alternatively, the target can be
supplied externally. In this case, the external voltage should be connected to pin 4 of the 14-pin connector.
The MSP-FET430UIF then adjusts the level of the JTAG signals to external VCC automatically. Only pin 2
(MSP-FET430UIF supplies target) or pin 4 (target is externally supplied) must be connected; not both at
the same time.
When a target socket module is powered from an external supply, the external supply powers the device
on the target socket module and any user circuitry connected to the target socket module, and the FET
interface module continues to be powered from the PC via the parallel port. If the externally supplied
voltage differs from that of the FET interface module, the target socket module must be modified so that
the externally supplied voltage is routed to the FET interface module (so that it may adjust its output
voltage levels accordingly). See the target socket module schematics in Appendix B.
2.3
Bootstrap Loader (BSL)
The JTAG pins provide access to the flash memory of the MSP430Fxxx devices. On some devices, these
pins are shared with the device port pins, and this sharing of pins can complicate a design (or sharing may
not be possible). As an alternative to using the JTAG pins, most MSP430Fxxx devices contain a program
(a "bootstrap loader") that permits the flash memory to be erased and programmed using a reduced set of
signals. The MSP430 Programming Via the Bootstrap Loader User's Guide (SLAU319) describes this
interface. TI does not produce a BSL tool. However, customers can easily develop their own BSL tools
using the information in the application reports, or BSL tools can be purchased from third parties. See the
MSP430 web site for the application reports and a list of MSP430 third-party tool developers.
TI suggests that MSP430Fxxx customers design their circuits with the BSL in mind (i.e., TI suggests
providing access to these signals via, for example, a header).
See FAQ Hardware #11 for a second alternative to sharing the JTAG and port pins.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
27
28
Design Considerations for In-Circuit Programming
© 2009–2010, Texas Instruments Incorporated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Appendix A
SLAU278F – May 2009 – Revised December 2010
Frequently Asked Questions and Known Issues
This appendix presents solutions to frequently asked questions regarding the MSP-FET430 hardware.
Topic
A.1
A.2
...........................................................................................................................
Page
Hardware FAQs ................................................................................................. 30
Known Issues ................................................................................................... 32
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Frequently Asked Questions and Known Issues
© 2009–2010, Texas Instruments Incorporated
29
Hardware FAQs
A.1
www.ti.com
Hardware FAQs
1. The state of the device (CPU registers, RAM memory, etc.) is undefined following a reset.
Exceptions to the above statement are that the PC is loaded with the word at 0xFFFE (i.e., the reset
vector), the status register is cleared, and the peripheral registers (SFRs) are initialized as documented
in the device family user's guides. The CCE/CCS debugger and C-SPY reset the device after
programming it.
2. MSP430F22xx Target Socket Module (MSP-TS430DA38) – Important Information
Due to the large capacitive coupling introduced by the device socket between the adjacent signals
XIN/P2.6 (socket pin 6) and RST/SBWTDIO (socket pin 7), in-system debugging can disturb the
LFXT1 low-frequency crystal oscillator operation (ACLK). This behavior applies only to the Spy-Bi-Wire
(2-wire) JTAG configuration and only to the period while a debug session is active.
Workarounds:
• Use the 4-wire JTAG mode debug configuration instead of the Spy-Bi-Wire (2-wire) JTAG
configuration. This can be achieved by placing jumpers JP4 through JP9 accordingly.
• Use the debugger option "Run Free" that can be selected from the Advanced Run drop-down
menu (at top of Debug View). This prevents the debugger from accessing the MSP430 while the
application is running. Note that, in this mode, a manual halt is required to see if a breakpoint was
hit. See the IDE documentation for more information on this feature.
• Use an external clock source to drive XIN directly.
3. With current interface hardware and software, there is a weakness when adapting target boards
that are powered externally. This leads to an accidental fuse check in the MSP430. This is valid for
PIF and UIF but is mainly seen on UIF. A solution is being developed.
Workarounds:
• Connect RST/NMI pin to JTAG header (pin 11), LPT/USB tools are able to pull the RST line, which
also resets the device internal fuse logic.
• Use the debugger option "Release JTAG On Go" that can be selected from the IDE drop-down
menu. This prevents the debugger from accessing the MSP430 while the application is running.
Note that in this mode, a manual halt is required to see if a breakpoint was hit. See the IDE
documentation for more information on this feature.
• Use an external clock source to drive XIN directly.
4. The 14-conductor cable connecting the FET interface module and the target socket module must not
exceed 8 inches (20 centimeters) in length.
5. The signal assignment on the 14-conductor cable is identical for the parallel port interface and the
USB FET.
6. To utilize the on-chip ADC voltage references, C6 (10 ?F, 6.3 V, low leakage) must be installed on
the target socket module.
7. To utilize the charge pump on the devices with LCD+ Module, C4 (10 ?F, low leakage) must be
installed on the target socket module.
8. Crystals/resonators Q1 and Q2 (if applicable) are not provided on the target socket module. For
MSP430 devices that contain user-selectable loading capacitors, the effective capacitance is the
selected capacitance plus 3 pF (pad capacitance) divided by two.
9. Crystals/resonators have no effect upon the operation of the tool and the CCE/CCS debugger or
C-SPY (as any required clocking/timing is derived from the internal DCO/FLL).
10. On 20-pin and 28-pin devices with multiplexed port/JTAG pins (P1.4 to P1.7), to use these pin in
their port capacity:
For CCE/CCS: "Run Free" (in Run pull-down menu at top of Debug View) must be selected.
For C-SPY: "Release JTAG On Go" must be selected.
11. As an alternative to sharing the JTAG and port pins (on 20 and 28 pin devices), consider using
an MSP430 device that is a "superset" of the smaller device. A very powerful feature of the
MSP430 is that the family members are code and architecturally compatible, so code developed on
one device (for example, one without shared JTAG and port pins) ports effortlessly to another
(assuming an equivalent set of peripherals).
30
Frequently Asked Questions and Known Issues
© 2009–2010, Texas Instruments Incorporated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware FAQs
www.ti.com
12. Information memory may not be blank (erased to 0xFF) when the device is delivered from TI.
Customers should erase the information memory before its first use. Main memory of packaged
devices is blank when the device is delivered from TI.
13. The device current increases by approximately 10 ?A when a device in low-power mode is
stopped [using Halt (CCE/CCS) or Esc (C-SPY)] and then the low-power mode is restored [using
Run (CCE/CCS) or Go (C-SPY)]. This behavior appears to happen on all devices except the
MSP430F12x.
14. The following ZIF sockets are used in the FET tools and target socket modules:
• 14-pin device (PW package): Enplas OTS-14-065-01
• 14-pin package for 'L092 (PW package): Yamaichi IC189-0142-146
• 24-pin package (PW package): Enplas OTS-24(28)-0.65-02
• 28-pin device (DW package): Wells-CTI 652 D028
• 28-pin device (PW package): Enplas OTS-28-0.65-01
• 38-pin device (DA package): Yamaichi IC189-0382-037
• 40-pin device (RHA package): Enplas QFN-40B-0.5-01
• 40-pin device (RSB package): Enplas QFN-40B-0.4
• 48-pin device (RGZ package): Yamaichi QFN11T048-008 A101121-001
• 48-pin device (DL package): Yamaichi IC51-0482-1163
• 64-pin device (PM package): Yamaichi IC51-0644-807
• 64-pin device (RGC package): Yamaichi QFN11T064-006
• 80-pin device (PN package): Yamaichi IC201-0804-014
• 100-pin device (PZ package): Yamaichi IC201-1004-008
Enplas: www.enplas.com
Wells-CTI: www.wellscti.com
Yamaichi: www.yamaichi.us
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Frequently Asked Questions and Known Issues
© 2009–2010, Texas Instruments Incorporated
31
Known Issues
A.2
www.ti.com
Known Issues
MSP-FET430PIF
Some PCs do not supply 5 V through the parallel port
Problem Description
Device identification problems with modern PCs, because the parallel port often does not
deliver 5 V as was common with earlier hardware.
1. When connected to a laptop, the test signal is clamped to 2.5 V.
2. When the external VCC becomes less than 3 V, up to 10 mA is flowing in the adapter
via pin 4 (sense).
Solution
Measure the voltage level of the parallel port. If it is too low, provide external 5 V to the
VCC pads of the interface. The jumper on a the target socket must be switched to
external power.
MSP-FET430UIF
Current detection algorithm of the UIF firmware
Problem Description
If high current is detected, the ICC Monitor algorithm stays in a loop of frequently
switching on and off the target power supply. This power switching puts some MSP430
devices such as the MSP430F5438 in a state that requires a power cycle to return the
device to JTAG control.
A side issue is that if the UIF firmware has entered this switch on / switch off loop, it is
not possible to turn off the power supply to the target by calling MSP430_VCC(0). A
power cycle is required to remove the device from this state.
Solution
32
IAR KickStart and Code Composer Essentials that have the MSP430.dll version
2.04.00.003 and higher do not show this problem. Update the software development tool
to this version or higher to update the MSP-FET430UIF firmware.
Frequently Asked Questions and Known Issues
© 2009–2010, Texas Instruments Incorporated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Appendix B
SLAU278F – May 2009 – Revised December 2010
Hardware
This appendix contains information relating to the FET hardware, including schematics, PCB pictorials,
and bills of materials. All other tools, such as the eZ430 series, are described in separate product-specific
user's guides.
Topic
...........................................................................................................................
B.1
B.2
B.3
B.4
B.5
B.6
B.7
B.8
B.9
B.10
B.11
B.12
B.13
B.14
B.15
B.16
B.17
B.18
B.19
B.20
B.21
B.22
B.23
B.24
B.25
B.26
B.27
B.28
B.29
Page
MSP-TS430PW14 ............................................................................................... 34
MSP-TS430L092 ................................................................................................ 37
MSP-TS430L092 Active Cable ............................................................................. 40
MSP-TS430PW24 ............................................................................................... 43
MSP-TS430DW28 ............................................................................................... 46
MSP-TS430PW28 ............................................................................................... 49
MSP-TS430PW28A ............................................................................................. 52
MSP-TS430DA38 ............................................................................................... 55
MSP-TS430QFN23x0 .......................................................................................... 58
MSP-TS430RSB40 ............................................................................................. 61
MSP-TS430RHA40A ........................................................................................... 64
MSP-TS430DL48 ................................................................................................ 67
MSP-TS430RGZ48B ........................................................................................... 70
MSP-TS430PM64 ............................................................................................... 73
MSP-TS430PM64A ............................................................................................. 76
MSP-TS430RGC64B ........................................................................................... 79
MSP-TS430RGC64USB ....................................................................................... 82
MSP-TS430PN80 ............................................................................................... 86
MSP-TS430PN80A ............................................................................................. 89
MSP-TS430PN80USB ......................................................................................... 91
MSP-TS430PZ100 .............................................................................................. 96
MSP-TS430PZ100A ............................................................................................ 99
MSP-TS430PZ100B .......................................................................................... 102
MSP-TS430PZ5x100 ......................................................................................... 105
MSP-TS430PZ100USB ...................................................................................... 107
EM430F5137RF900 ........................................................................................... 112
EM430F6137RF900 ........................................................................................... 116
MSP-FET430PIF ............................................................................................... 120
MSP-FET430UIF ............................................................................................... 122
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
33
MSP-TS430PW14
B.1
www.ti.com
MSP-TS430PW14
Figure B-1. MSP-TS430PW14 Target Socket Module, Schematic
34
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW14
www.ti.com
Connector J3
External power connector
Jumper J5 to 'ext'
LED connected to P1.0
Jumpers J7 to J12
Close 1-2 to debug in
Spy-Bi-Wire Mode.
Close 2-3 to debug in
4-wire JTAG mode.
Jumper J4
Open to disconnect LED
Orient Pin 1 of
MSP430 device
Jumper J6
Open to measure current
Figure B-2. MSP-TS430PW14 Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
35
MSP-TS430PW14
www.ti.com
Table B-1. MSP-TS430PW14 Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C7
1
10uF/10V, Tantal Size B 511-1463-2-ND
3
C3, C5
1
100nF, SMD0805
4
C8
0
2.2nF, SMD0805
5
D1
1
green LED, SMD0603
475-1056-2-ND
6
J1, J2
0
7-pin header, TH
"SAM1029-07NDSAM1213-07-ND"
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder: Header: Receptacle
7
J3, J5, J7,
J8, J9, J10,
J11, J12
8
3-pin header, male, TH
SAM1035-03-ND
Place jumpers on headers J5, J7, J8,
J9, J10, J11, J12; Pos 1-2
8
J4, J6
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
9
Jumper
15-38-1024-ND
Place on: J5, J7-J12; Pos 1-2
9
36
Description
DigiKey Part No.
Comment
DNP
478-3351-2-ND
DNP: C3
DNP
10
JTAG
1
14-pin connector, male,
TH
HRP14H-ND
12
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
DNP: keep vias free of solder
12.5pF
13
R2, R3
2
330 Ω, SMD0805
541-330ATR-ND
15
R5
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: OTS-14-0.65-01
17
PCB
1
56 x 53 mm
18
Adhesive
plastic feet
4
about 6mm width, 2mm
height
19
MSP430
2
MSP430F2013IPW
Manuf.: Enplas
2 layers
e.g., 3M Bumpons Part
No. SJ-5302
Hardware
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430L092
www.ti.com
B.2
MSP-TS430L092
Figure B-3. MSP-TS430L092 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
37
MSP-TS430L092
www.ti.com
Settings of the MSP-TS430L092 Target Socket
Figure B-4 shows the PCB layout of the MSP-TS430L092 target socket. The following pinning is
recommended:
• JP1 is write enable for the EPROM. If this is not set, the EPROM can only be read.
• JP2 and JP3 connect device supply with boost converter. They can be opened to measure device
current consumption. For default operation, they should be closed.
Figure B-4. MSP-TS430L092 Target Socket Module, PCB
38
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430L092
www.ti.com
Table B-2. MSP-TS430L092 Bill of Materials
Pos.
Ref Des No.
No. Per
Board
1
C1, C2
2
330nF, SMD0603
2
C5
1
100n, SMD0603
3
C6
1
10u, SMD0805
4
C10
1
100n, SMD0603
5
EEPROM1
1
M95512 SO08 (SO8)
7
J1, J2
2
Description
DigiKey Part No.
ST Micro M95160R
Comment
Digikey: 497-8688-1-ND
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder.
7-pin header, TH
SAM1213-07-ND
: Header
SAM1035-07-ND
: Receptacle
8
J3
1
3-pin header, male, TH
SAM1035-03-ND
9
J4, J5
2
FE4L, FE4H
4 pol. Stiftreihe
11
J13
1
MICRO_STECKV_10
12
JP1, JP2,JP3
3
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
15
L1
1
33uH, SMD0806
LQH2MCN330K02L
Farnell: 151-5557
16
LED1, LED4
2
LEDCHIPLED_0603
17
Q2
1
BC817-16LT1SMD
18
R0, R6, R7
3
2K7, SMD0603
19
R1
1
1k, SMD0603
20
R2
1
47k, SMD0603
21
R4,R5, R8,
R10, RC, RD
6
10k, SMD0603
22
RA
1
3.9k, SMD0603
23
RB
1
6.8k, SMD0603
24
U1
1
14 Pin Socket IC189-0142-146
Manuf. Yamaichi
22
MSP430
2
MSP430L092PWR
DNP: enclosed with kit. Is
supplied by TI
DNP; Keep vias free of
solder.
Reichelt:
MicroMaTch-Connector: MM
FL 10G
Farnell: 1686065
BC817-16LT1SMD
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
SOT23-BEC
Hardware
© 2009–2010, Texas Instruments Incorporated
39
MSP-TS430L092 Active Cable
B.3
www.ti.com
MSP-TS430L092 Active Cable
Figure B-5. MSP-TS430L092 Active Cable Target Socket Module, Schematic
40
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430L092 Active Cable
www.ti.com
Figure B-6 shows the PCB layout for the Active Cable. The following pinning is possible:
• JP1 has two jumpers (Jumper 1 and Jumper 2) that can be set as shown in Table B-3.
Table B-3. MSP-TS430L092 JP1 Settings
•
Jumper 1
Jumper 2
Description
Off
Off
The active cable has no power and does not function.
Off
On
The active cable receives power from target socket. For this option, the
target socket must have its own power supply.
On
Off
The active cable receives power from the JTAG connector.
On
On
The JTAG connector powers the active cable and the target socket. For
this option, the target socket must not have its own power source, as this
would cause a not defined state.
JP2 is for reset. For the standard MSP-TS430L092, this jumper must be set. It sets the reset pin to
high and can also control it. Without this jumper on the MSP-TS430L092, reset is set to zero.
Figure B-6. MSP-TS430L092 Active Cable Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
41
MSP-TS430L092 Active Cable
www.ti.com
Table B-4. MSP-TS430L092 Active Cable Bill of Materials
42
Pos.
Ref Des
No. Per
Board
1
C1, C3, C5,
C6
4
100nF, SMD0603
2
C2, C4
2
1uF, SMD0805
3
R1, R10
2
10K, SMD0603
4
R2
1
4K7, SMD0603
5
R5, R6, R7,
R9
4
100, SMD0603
6
R8
1
680k, SMD0603
7
R11, R15
2
1K, SMD0603
8
R12
0
SMD0603
DNP
9
R13
0
SMD0603
DNP
10
R14
1
0, SMD0603
11
IC1
1
SN74AUC1G04DBVR
12
IC2, IC3, IC4
3
SN74AUC2G125DCTR
Description
DigiKey Part No.
Comment
Manu: TI
Manu: TI
13
J2
1
MICRO_STECKV_10
Reichelt:
MicroMaTch-Connector: MM
FL 10G
14
JP1
1
2x2 Header
JP2Q
Put jumper on Position 1 and
2. Do not mix direction.
15
JP2
1
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
16
JTAG
1
14-pin connector, male, TH
HRP14H-ND
Digi-Key:
BC817-25LT1GOSCT-ND
SOT23-5
17
Q1
1
BC817-25LT1SMD,
SOT23-BEC
18
U1, U2
2
TLVH431IDBVR
Hardware
Manu: TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW24
www.ti.com
B.4
MSP-TS430PW24
Figure B-7. MSP-TS430PW24 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
43
MSP-TS430PW24
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumper JP2
Open to measure current
Jumpers JP4 to JP9
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Orient Pin 1 of MSP430 device
D1 LED connected to P1.0
Jumper JP3
Open to disconnect LED
Figure B-8. MSP-TS430PW24 Target Socket Module, PCB
44
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW24
www.ti.com
Table B-5. MSP-TS430PW24 Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C5
1
2.2nF, SMD0805
3
C3, C7
2
10uF/10V, SMD0805
4
C4, C6, C8
3
100nF, SMD0805
478-3351-2-ND
5
D1
1
green LED, SMD0805
P516TR-ND
6
J1, J2
0
12-pin header, TH
"SAM1029-07NDSAM1213-07-ND"
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder. (Header & Receptacle)
7
J5, JP1,
JP4, JP5,
JP6, JP7,
JP8, JP9
8
3-pin header, male, TH
SAM1035-03-ND
Place jumper on 1-2 of JP4-JP9
Place on 1-2 on JP1
8
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
9
Jumper
15-38-1024-ND
see Pos 7 an 8
HRP14H-ND
9
Description
DigiKey Part No.
Comment
DNP
10
JTAG
1
14-pin connector, male,
TH
11
Q1
0
Crystal
12
R1, R7
2
330 Ω, SMD0805
541-330ATR-ND
13
R5, R6,
R8, R9,
2
0 Ohm, SMD0805
541-000ATR-ND
14
R4
1
47k Ohm, SMD0805
541-47000ATR-ND
Manuf.: Enplas
2 layers
15
U1
1
Socket: OTS
24(28)-065-02-00
16
PCB
1
68.5 x 61 mm
17
Adhesive
plastic feet
4
about 6mm width, 2mm
height
18
MSP430
2
MSP430AFE2xx
DNP: keep vias free of solder
e.g., 3M Bumpons Part
No. SJ-5302
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP R5, R6
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
45
MSP-TS430DW28
B.5
www.ti.com
MSP-TS430DW28
Figure B-9. MSP-TS430DW28 Target Socket Module, Schematic
46
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430DW28
www.ti.com
LED connected to P1.0
Jumper J4
Open to disconnect LED
Jumper J5
Open to measure current
Connector J3
External power connector
Remove R8 and jumper R9
Orient Pin 1 of
MSP430 device
Figure B-10. MSP-TS430DW28 Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
47
MSP-TS430DW28
www.ti.com
Table B-6. MSP-TS430DW28 Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C5
1
100nF, SMD0805
3
C7
1
10uF/10V Tantal Elko B
4
C8
1
10nF
SMD0805
5
D1
1
LED3 T1 3mm yellow
RS: 228-4991
6
Q1
0
QUARZ, Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
DNP: Cover holes while soldering
12.5pF
7
J1, J2
2
14-pin header, TH male
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder.: Header: Receptacle
2
14-pin header, TH
female
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder.: Header: Receptacle
7.1
48
Description
DigiKey Part No.
Comment
DNP: C1, C2, Cover holes while
soldering
8
J3
1
3-Pin Connector, male
9
J4, J5
2
2-Pin Connector, male
10
BOOTST
0
ML10, 10-Pin Conn., m
RS: 482-115
11
JTAG
1
ML14, 14-Pin Conn., m
RS: 482-121
12
R1, R2,
R6, R7,
R8,R9,
R10, R11
4
0R, SMD0805
13
R3
1
560R, SMD0805
14
R5
1
47K, SMD0805
15
U1
1
SOP28DW socket
16
U2
0
TSSOP
With jumper
DNP, Cover holes while soldering
DNP: R1, R2, R9, R10
Yamaichi:
IC189-0282-042
Hardware
DNP
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW28
www.ti.com
B.6
MSP-TS430PW28
Figure B-11. MSP-TS430PW28 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
49
MSP-TS430PW28
www.ti.com
Jumper JP4 to JP9:
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Jumper JP1
1-2 (int): Power supply via JTAG interface
2-3 (ext): External Power Supply
Jumper JP2
Open to measure current
Orient Pin 1 of Device
Jumper JP3
Open to disconnect LED
LED D1 connected to P5.1
Figure B-12. MSP-TS430PW28 Target Socket Module, PCB
50
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW28
www.ti.com
Table B-7. MSP-TS430PW28 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C3
1
10uF/10V Tantal Elko B
3
C4
1
100nF, SMD0805
4
C5
0
2.2nF, SMD0805
5
D1
1
LED green SMD0603
6
Q1
0
QUARZ, Crystal
7
J1, J2
7.1
(1)
Description
(1)
DigiKey Part No.
Comment
DNP: C1, C2 , Cover holes
while soldering
DNP
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
DNP: Cover holes and
neighboring holes while
soldering
14-pin header, TH male
DNP: Headers and
receptacles enclosed with
kit.Keep vias free of
solder.: Header:
Receptacle
2
14-pin header, TH female
DNP: headers and
receptacles enclosed with
kit.Keep vias free of
solder.: Header:
Receptacle
2
8
J5, IP1
1
3-Pin Connector , male
8a
JP1, JP4,
JP5, JP6,
JP7, JP8,
JP9
7
3-Pin Connector , male
Jumper on Pos 1-2
9
JP2, JP3
2
2-Pin Connector , male
with Jumper
10
BOOTST
0
ML10, 10-Pin Conn. , m
RS: 482-115
11
JTAG
1
ML14, 14-Pin Conn. , m
RS: 482-121
12
R1, R7
2
330R, SMD0805
12
R2, R3, R5,
R6
0
0R, SMD0805
14
R4
1
47K, SMD0805
15
U1
1
SOP28PW socket
DNP: Cover holes while
soldering
DNP
Enplas: OTS-28-0.65-01
PCB 66 x 79 mm, two layers; Rubber stand off, four pieces
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
51
MSP-TS430PW28A
B.7
www.ti.com
MSP-TS430PW28A
Figure B-13. MSP-TS430PW28A Target Socket Module, Schematic
52
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PW28A
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumper JP2
Open to measure current
Jumpers JP4 to JP9
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Orient Pin 1 of MSP430 device
Jumper JP3
Open to disconnect LED
D1 LED connected to P1.0
Figure B-14. MSP-TS430PW28A Target Socket Module, PCB (Red)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
53
MSP-TS430PW28A
www.ti.com
Table B-8. MSP-TS430PW28A Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C5
1
2.2nF, SMD0805
3
C3
1
10uF/10V, SMD0805
4
C4, C6,
2
100nF, SMD0805
478-3351-2-ND
5
D1
1
green LED, SMD0805
P516TR-ND
6
J1, J2
0
14-pin header, TH
7
J5, JP1,
JP4, JP5,
JP6, JP7,
JP8, JP9
8
3-pin header, male, TH
SAM1035-03-ND
Place jumper on 1-2 of JP4-JP9
Place on 1-2 on JP1
8
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
9
Jumper
15-38-1024-ND
see Pos 7 an 8
14-pin connector, male,
TH
HRP14H-ND
9
54
Description
DigiKey Part No.
Comment
DNP
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder: (Header & Receptacle)
10
JTAG
1
11
BOOTST
0
12
Q1
0
Crystal
Micro Crystal MS3V
32.768kHz, C(Load) =
12.5pF
13
R1, R7
2
330 Ω, SMD0805
541-330ATR-ND
14
R2, R3,R5,
R6,
0
0 Ohm, SMD0805
541-000ATR-ND
15
R4
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: OTS-28-0.65-01
17
PCB
1
63.5 x 64.8 mm
18
Adhesive
plastic feet
4
about 6mm width, 2mm
height
19
MSP430
2
MSP430G2553IPW28
DNP Keep vias free of solder
DNP: keep vias free of solder
DNP R2, R3,R5, R6
Manuf.: Enplas
2 layers
e.g., 3M Bumpons Part
No. SJ-5302
Hardware
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430DA38
www.ti.com
B.8
MSP-TS430DA38
Figure B-15. MSP-TS430DA38 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
55
MSP-TS430DA38
www.ti.com
Jumpers JP4 to JP9
Close 1-2 to debug in
Spy-Bi-Wire Mode,
Close 2-3 to debug in
4-wire JTAG Mode
LED connected to P1.0
Jumper JP3
Open to disconnect LED
Orient pin 1 of
MSP430 device
Jumper JP2
Open to measure current
Connector J3
External power connector
Jumper JP1 to 'ext'
Figure B-16. MSP-TS430DA38 Target Socket Module, PCB
56
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430DA38
www.ti.com
Table B-9. MSP-TS430DA38 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C7
1
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5
1
100nF, SMD0805
478-3351-2-ND
4
C8
0
2.2nF, SMD0805
5
D1
1
green LED, SMD0603
Description
DigiKey Part No.
Comment
DNP
DNP
475-1056-2-ND
6
J1, J2
0
19-pin header, TH
"SAM1029-19NDSAM1213-19-ND"
DNP: headers and
receptacles enclosed with
kit.Keep vias free of
solder.: Header:
Receptacle
7
"J3, JP1,
JP4, JP5,
JP6, JP7,
JP8, JP9"
8
3-pin header, male, TH
SAM1035-03-ND
Place jumpers on headers
JP1, JP4,JP5, JP6, JP7,
JP8, JP9; Pos 1-2
8
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
9
Jumper
15-38-1024-ND
Place on: JP1 - JP9; Pos
1-2
HRP14H-ND
9
10
JTAG
1
14-pin connector, male, TH
11
BOOTST
0
10-pin connector, male, TH
12
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
13
R1, R3
2
330 Ω, SMD0805
541-330ATR-ND
14
R10, R11
0
0 Ω, SMD0805
541-000ATR-ND
15
R5
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: IC189-0382--037
Manuf.: Yamaichi
17
PCB
1
67 x 66 mm
2 layers
18
Adhesive
Plastic feet
4
~6mm width, 2mm height
19
MSP430
2
MSP430F2274IDA
DNP: Keep vias free of
solder
e.g., 3M Bumpons Part No.
SJ-5302
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP: Keep vias free of
solder
DNP
Apply to corners at bottom
side
DNP: enclosed with kit
supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
57
MSP-TS430QFN23x0
B.9
www.ti.com
MSP-TS430QFN23x0
Figure B-17. MSP-TS430QFN23x0 Target Socket Module, Schematic
58
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430QFN23x0
www.ti.com
Connector J5
External power connector
Jumper JP1 to 'ext'
Jumper JP2
Open to measure current
Jumper JP3
Open to disconnect LED
LED connected
to P1.0
Figure B-18. MSP-TS430QFN23x0 Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
59
MSP-TS430QFN23x0
www.ti.com
Table B-10. MSP-TS430QFN23x0 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C3
1
10uF/10V, Tantal Size B
511-1463-2-ND
3
C4
1
100nF, SMD0805
478-3351-2-ND
4
C5
1
10nF, SMD0805
478-1383-2-ND
5
D1
1
green LED, SMD0603
475-1056-2-ND
DigiKey Part No.
Comment
DNP
6
J1, J2, J3,
J4
0
10-pin header, TH
DNP: headers and
receptacles enclosed with
SAM1034-10-NDSAM1212kit.Keep vias free of
10-ND
solder.: Header:
Receptacle
7
J5, JP1
2
3-pin header, male, TH
SAM1035-03-ND
Place jumper on header
JP1; Pos 1-2.
8
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
Place on: JP1, JP2, JP3
9
60
Description
3
Jumper
15-38-1024-ND
10
JTAG
1
14-pin connector, male, TH
HRP14H-ND
11
BOOTST
0
10-pin connector, male, TH
12
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
13
R1
1
330 Ω, SMD0805
541-330ATR-ND
14
R2, R3
0
0 Ω, SMD0805
541-000ATR-ND
15
R4
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: QFN-40B-0.5-01
17
PCB
1
79 x 66 mm
18
Adhesive
Plastic feet
4
~6mm width, 2mm height
19
MSP430
2
MSP430F2370IRHA
DNP: Keep vias free of
solder
DNP: Keep vias free of
solder
DNP
Manuf.: Enplas
2 layers
e.g., 3M Bumpons Part No.
SJ-5302
Hardware
Apply to corners at bottom
side
DNP: enclosed with kit
supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RSB40
www.ti.com
B.10 MSP-TS430RSB40
Figure B-19. MSP-TS430RSB40 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
61
MSP-TS430RSB40
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumper JP2
Open to measure current
Jumpers JP4 to JP9
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Orient Pin 1 of MSP430 device
Jumper JP3
Open to disconnect LED
D1 LED connected to P1.0
Figure B-20. MSP-TS430RSB40 Target Socket Module, PCB
62
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RSB40
www.ti.com
Table B-11. MSP-TS430RSB40 Bill of Materials
Ref Des
No. Per
Board
Description
1
C1, C2
0
12pF, SMD0805
2
C3, C7, C10,
C12
3
10uF/10V, SMD 0805
445-1371-1-ND
DNP C12
3
C4, C6, C8,
C11
3
100nF, SMD0805
311-1245-2-ND
DNP C11
4
C5
1
2.2nF, SMD0805
5
C9
1
470nF, SMD0805
6
D1
1
green LED, SMD0805
Pos.
DigiKey Part No.
Comment
DNP: C1, C2
P516TR-ND
10-pin header, TH
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder. :
Header : Receptacle
4
10-pin header, TH
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder. :
Header : Receptacle
8
JP1,
JP4,JP5,
JP6, JP7,
JP8, JP9, J5,
JP10
9
3-pin header, male, TH
SAM1035-03-ND
Jumper: 1-2 on JP1, JP10;
2-3 on JP4-JP9
place jumper on header
7
J1, J2, J3, J4
7.1
4
9
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
10
JTAG
1
14-pin connector, male, TH
HRP14H-ND
11
BOOTST
0
10-pin connector, male, TH
12
U1
1
QFN-40B-0.4_
ENPLAS_SOCKET
Enplas
13
Q1
0
Crystal
Micro Crystal MS3V-T1R
32.768kHz, C(Load) =
12.5pF
DNP: Q1. Keep vias free of
solder
10
Jumper
15-38-1024-ND
Place on: JP1, JP2, JP3,
JP4, JP5, JP6, JP7, JP8,
JP9, JP10
15
16
R1,R7
2
330R SMD0805
17
R2, R3, R5,
R6, R8, R9,
R10
3
0R SMD0805
18
R4
1
47k SMD0805
19
MSP430
2
MSP430F5132
20
Rubber stand
off
4
DNP. Keep vias free of
solder
DNP R2, R3, R5, R6
DNP: enclosed with kit. Is
supplied by TI
select appropriate; e.g.,
Buerklin: 20H1724
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
apply to corners at bottom
side
Hardware
© 2009–2010, Texas Instruments Incorporated
63
MSP-TS430RHA40A
www.ti.com
B.11 MSP-TS430RHA40A
Figure B-21. MSP-TS430RHA40A Target Socket Module, Schematic
64
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RHA40A
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumper JP2
Open to measure current
Jumpers JP4 to JP9
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
D1 LED connected to P1.0
Jumper JP3
Open to disconnect LED
Orient Pin 1 of MSP430 device
Figure B-22. MSP-TS430RHA40A Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
65
MSP-TS430RHA40A
www.ti.com
Table B-12. MSP-TS430RHA40A Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP: C1, C2
2
C5
0
2.2nF, SMD0805
DNP C12
3
C3, C7
2
10uF/10V, SMD0805 5
4
C4, C6
2
100nF, SMD0805
5
C9
1
470nF, SMD0805
6
D1
1
green LED, SMD0805
7
J1, J2, J3,
J4
4
10-pin header, TH
DNP: headers and receptacles
enclosed with kit. Keep vias free of
solder. : Header : Receptacle
4
10-pin header, TH
DNP: headers and receptacles
enclosed with kit. Keep vias free of
solder. : Header : Receptacle
8
J5, JP1,
JP4, JP5,
JP6, JP7,
JP8, JP9
8
3-pin header, male, TH
SAM1035-03-ND
Place jumper on 1-2 of JP4-JP9;
Place on 1-2 on JP1
9
JP2, JP3
2
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
9
Jumper
15-38-1024-ND
see Pos 8 an 9
HRP14H-ND
7.1
10
11
JTAG
1
14-pin connector, male,
TH
12
BOOTST
0
10-pin connector, male,
TH
13
U1
1
Socket: QFN-40B-0.5-01
DigiKey Part No.
Comment
DNP C11
478-3351-2-ND
P516TR-ND
DNP. Keep vias free of solder
Manuf.: Enplas
Q1
0
Crystal
Micro Crystal MS3V-T1R
32.768kHz, C(Load) =
12.5pF
15
R1,R7
2
330R SMD0805
541-330ATR-ND
16
R2, R3,
R5, R6,
R8, R9,
2
0 Ohm, SMD0805
541-000ATR-ND
17
R4
1
47k SMD0805
18
PCB
1
79 x 66 mm
19
Rubber
stand off
4
20
MSP430
2
14
66
Description
DNP: Q1. Keep vias free of solder
DNP:R2, R3, R5, R6
2 layers
select appropriate; e.g.,
Buerklin: 20H1724
MSP430N5736IRHA
Hardware
apply to corners at bottom side
DNP: enclosed with kit. Is supplied by
TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430DL48
www.ti.com
B.12 MSP-TS430DL48
Figure B-23. MSP-TS430DL48 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
67
MSP-TS430DL48
www.ti.com
Jumper J5
Open to measure current
LED connected
to P1.0
Connector J3
External power connector
Jumper JP1 to ‘ext’
Jumper J4
Open to
disconnect LED
Orient pin 1 of
MSP430 device
Figure B-24. MSP-TS430DL48 Target Socket Module, PCB
68
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430DL48
www.ti.com
Table B-13. MSP-TS430DL48 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C4, C7
2
10uF/10V, Tantal Size B
511-1463-2-ND
3
C3, C5
2
100nF, SMD0805
478-3351-2-ND
4
C8
1
10nF, SMD0805
478-1383-2-ND
5
D1
1
yellow LED, TH, 3mm, T1
511-1251-ND
Description
DigiKey Part No.
Comment
DNP
6
J1, J2
0
24-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1034-12-NDSAM1212kit.Keep vias free of
12-ND
solder.: Header:
Receptacle
7
J3, JP1, JP2
2
3-pin header, male, TH
SAM1035-03-ND
Place jumper on header
JP1; Pos 1-2. DNP: JP2
8
J4, J5
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
Place on: JP1, J4, J5
3
Jumper
15-38-1024-ND
10
9
JTAG
1
14-pin connector, male, TH
HRP14H-ND
11
BOOTST
0
10-pin connector, male, TH
12
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
13
R3
1
560 Ω, SMD0805
541-560ATR-ND
14
R4, R6, R7,
R12
2
0 Ω, SMD0805
541-000ATR-ND
15
R5
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: IC51-1387
KS-15186
Manuf.: Yamaichi
17
PCB
1
58 x 66 mm
2 layers
18
Adhesive
Plastic feet
4
~6mm width, 2mm height
19
MSP430
2
MSP430F4270IDL
DNP: Keep vias free of
solder
e.g., 3M Bumpons Part No.
SJ-5302
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP: Keep vias free of
solder
DNP: R6, R7
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
69
MSP-TS430RGZ48B
www.ti.com
B.13 MSP-TS430RGZ48B
Figure B-25. MSP-TS430RGZ48B Target Socket Module, Schematic
70
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RGZ48B
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumpers JP5 to JP10
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Jumper JP1
Open to measure current
Orient Pin 1 of MSP430 device
Jumper JP2
Open to disconnect LED
D1 LED connected to P1.0
Figure B-26. MSP-TS430RGZ48B Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
71
MSP-TS430RGZ48B
www.ti.com
Table B-14. MSP-TS430RGZ48B Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP
2
C3, C4
0
47pF, SMD0805
DNP
3
C6, C7,
C12
3
10uF/6.3V, SMD0805
4
C5, C11,
C13, C14
4
100nF, SMD0805
5
C8
1
2.2nF, SMD0805
6
C9
1
470nF, SMD0805
478-1403-2-ND
7
D1
1
green LED, SMD0805
P516TR-ND
8
J1, J2, J3,
J4
0
12-pin header, TH
SAM1029-12-ND
(Header)
SAM1213-12-ND
(Receptacle)
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder:
9
J5
1
3-pin header, male, TH
10
JP3, JP5,
JP6, JP7,
JP8, JP9,
JP10
7
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3 on JP5,
JP6, JP7, JP8, JP9, JP10 place
jumpers on pins 1-2 on JP3,
11
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
9
Jumper
15-38-1024-ND
See Pos. 10and Pos. 11
HRP14H-ND
12
72
Description
DigiKey Part No.
Comment
311-1245-2-ND
13
JTAG
1
14-pin connector, male,
TH
14
BOOTST
0
10-pin connector, male,
TH
15
Q1
0
Crystal
Micro Crystal MS3V-T1R
32.768kHz, C(Load) =
DNP: Q1 Keep vias free of solder
12.5pF
16
Q2
0
Crystal
Q2: 4MHz Buerklin:
78D134
17
Insulating
disk to Q2
0
Insulating disk to Q2
http://www.ettinger.de/Ar
t_Detail.cfm?ART_ART
NUM=70.08.121
18
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
19
R1, R2,
R4, R6,
R8,
R9,R10,
R11, R12
3
0 Ohm, SMD0805
541-000ATR-ND
20
R5
1
47k Ω, SMD0805
541-47000ATR-ND
21
U1
1
Socket:
QFN11T048008_A101121_RGZ48
Manuf.: Yamaichi
22
PCB
1
81 x 76 mm
2 layers
23
Adhesive
plastic feet
4
about 6mm width, 2mm
height
24
MSP430
2
MSP430F5342IRGZ
"DNP Keep vias free of solder"
e.g., 3M Bumpons Part
No. SJ-5302
Hardware
DNP: Q2 Keep vias free of solder
DNP: R6, R8, R9, R10, R11,R12
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PM64
www.ti.com
B.14 MSP-TS430PM64
NOTE: Connections between the JTAG header and pins XOUT and XIN are no longer required and should not be
made.
Figure B-27. MSP-TS430PM64 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
73
MSP-TS430PM64
www.ti.com
Connector J5
External power connection
Remove R8 and jumper R9
LED connected
to pin 12
Jumper J7
Open to measure current
Jumper J6
Open to disconnect LED
Orient Pin 1 of
MSP430 device
Figure B-28. MSP-TS430PM64 Target Socket Module, PCB
74
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PM64
www.ti.com
Table B-15. MSP-TS430PM64 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP
1.1
C3, C4
0
47pF, SMD0805
DNP: Only
recommendation. Check
your crystal spec.
2
C6, C7
1
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5
1
100nF, SMD0805
478-3351-2-ND
4
C8
1
10nF, SMD0805
478-1383-2-ND
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
P516TR-ND
7
J1, J2, J3,
J4
0
16-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1029-16-NDSAM1213kit.Keep vias free of
16-ND
solder.: Header:
Receptacle
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
J6, J7
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
2
Jumper
15-38-1024-ND
Place on: J6, J7
HRP14H-ND
11
Description
DigiKey Part No.
Comment
DNP: C6
12
JTAG
1
14-pin connector, male, TH
13
BOOTST
0
10-pin connector, male, TH
14
Q1, Q2
0
Crystal
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
15
R3
1
330 Ω, SMD0805
541-330ATR-ND
16
R1, R2, R4,
R6, R7, R8,
R9, R10,
R11, R12,
R13, R14
3
0 Ω, SMD0805
541-000ATR-ND
17
R5
1
47k Ω, SMD0805
541-47000ATR-ND
18
U1
1
Socket: IC51-0644-807
Manuf.: Yamaichi
19
PCB
1
78 x 75 mm
2 layers
20
Rubber
standoff
4
21
MSP430
22
DNP: Keep vias free of
solder
select appropriate
MSP430F2619IPM
MSP430F417IPM
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP: Keep vias free of
solder
DNP: R4, R6, R7, R9, R10,
R11, R12, R13, R14
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
75
MSP-TS430PM64A
www.ti.com
B.15 MSP-TS430PM64A
Figure B-29. MSP-TS430PM64A Target Socket Module, Schematic
76
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PM64A
www.ti.com
Jumper JP3
1-2 (int): Power supply via JTAG interface
2-3 (ext): External Power Supply
Jumper JP4 to JP9:
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Jumper JP2
Open to measure current
Orient Pin 1 of Device
Jumper JP1
Open to disconnect LED
LED D1 connected to P5.1
Figure B-30. MSP-TS430PM64A Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
77
MSP-TS430PM64A
www.ti.com
Table B-16. MSP-TS430PM64A Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2,
0
12pF, SMD0805
DNP
2
C3
0
2.2nF, SMD0805
DNP
3
C6,
1
10uF/10V, Tantal Size B
511-1463-2-ND
4
C4, C5
2
100nF, SMD0805
478-3351-2-ND
5
D1
1
green LED, SMD0805
P516TR-ND
DigiKey Part No.
Comment
6
J1, J2, J3,
J4
0
16-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1029-16-NDSAM1213kit. Keep vias free of
16-ND
solder.: Header:
Receptacle
7
J5, JP3,
JP4, JP5,
JP6, JP7,
JP8, JP9
8
3-pin header, male, TH
SAM1035-03-ND
8
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
2
Jumper
15-38-1024-ND
Place on: J6, J7
HRP14H-ND
9
78
Description
10
JTAG
1
14-pin connector, male, TH
11
BOOTST
0
10-pin connector, male, TH
12
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
13
R3, R6
2
330 Ω, SMD0805
541-330ATR-ND
14
R1, R2, R5,
R7, R9, R10,
R11, R13,
R14
2
0 Ω, SMD0805
541-000ATR-ND
15
R4
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: IC51-0644-807
Manuf.: Yamaichi
17
PCB
1
78 x 75 mm
4 layers
18
Rubber
stand off
4
19
MSP430
2
DNP: Keep vias free of
solder
select appropriate
MSP430F4152IPM
Hardware
DNP: Keep vias free of
solder
DNP: R5, R7, R9, R10,
R11, R13, R14
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RGC64B
www.ti.com
B.16 MSP-TS430RGC64B
Figure B-31. MSP-TS430RGC64B Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
79
MSP-TS430RGC64B
www.ti.com
Connector J5
External power connector
Jumper JP3 to "ext"
Jumpers JP5 to JP10
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
If the system should
be supplied via LDOI (J6),
close JP4 and
set JP3 to external
Orient Pin 1 of MSP430 device
D1 LED connected to P1.0
Jumper JP2
Open to disconnect LED
Figure B-32. MSP-TS430RGC64B Target Socket Module, PCB
80
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RGC64B
www.ti.com
Table B-17. MSP-TS430RGC64B Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP
2
C3, C4
0
47pF, SMD0805
DNP
3
C6, C7,
C10
3
10uF/6.3V, SMD0805
4
C5, C11,
C13, C14,
C15
5
100nF, SMD0805
5
C8
1
2.2nF, SMD0805
6
C9
1
470nF, SMD0805
7
C16
1
4.7uF, SMD0805
8
C17
1
220nF, SMD0805
9
D1
1
green LED, SMD0805
P516TR-ND
10
J1, J2, J3,
J4
0
16-pin header, TH
SAM1029-16-ND
(Header)
SAM1213-16-ND
(Receptacle)
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder:
11
J5 , J6
2
3-pin header, male, TH
12
JP3, JP5,
JP6, JP7,
JP8, JP9,
JP10
7
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3 on JP5,
JP6, JP7, JP8, JP9, JP10 place
jumpers on pins 1-2 on JP3,
13
JP1, JP2,
JP4
3
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
10
Jumper
15-38-1024-ND
See Pos. 12 and Pos. 13
HRP14H-ND
14
Description
DigiKey Part No.
Comment
311-1245-2-ND
478-1403-2-ND
15
JTAG
1
14-pin connector, male,
TH
16
BOOTST
0
10-pin connector, male,
TH
17
Q1
0
Crystal
Micro Crystal MS3V-T1R
32.768kHz, C(Load) =
DNP: Q1 Keep vias free of solder
12.5pF
18
Q2
0
Crystal
Q2: 4MHz Buerklin:
78D134
19
Insulating
disk to Q2
0
Insulating disk to Q2
http://www.ettinger.de/Ar
t_Detail.cfm?ART_ART
NUM=70.08.121
20
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
21
R1, R2,
R4, R6,
R8,
R9,R10,
R11, R12
3
0 Ohm, SMD0805
541-000ATR-ND
22
R5
1
47k Ω, SMD0805
541-47000ATR-ND
23
U1
1
Socket:
QFN11T064-006-N-HSP
Manuf.: Yamaichi
24
PCB
1
85 x 76 mm
2 layers
25
Adhesive
plastic feet
4
about 6mm width, 2mm
height
2
MSP430F5310 RGC
26
D3,D4
27
MSP430
"DNP Keep vias free of solder"
e.g., 3M Bumpons Part
No. SJ-5302
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP: Q2 Keep vias free of solder
DNP: R6, R8, R9, R10, R11,R12
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
81
MSP-TS430RGC64USB
www.ti.com
B.17 MSP-TS430RGC64USB
Due to the use of diodes in the power chain, the voltage on the MSP430F5xx device is approximately
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
Figure B-33. MSP-TS430RGC64USB Target Socket Module, Schematic
82
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RGC64USB
www.ti.com
Figure B-34. MSP-TS430RGC64USB Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
83
MSP-TS430RGC64USB
www.ti.com
Table B-18. MSP-TS430RGC64USB Bill of Materials
Pos.
Ref Des
No. Per
Board
1
C1, C2
0
12pF, SMD0805
1.1
C3, C4
2
47pF, SMD0805
2
C6, C7
2
10uF/6.3V, Tantal Size B
511-1463-2-ND
3
C5, C11,
C13, C14
4
100nF, SMD0805
311-1245-2-ND
3.1
C10, C12
0
10uF, SMD0805
4
C8
1
2.2nF, SMD0805
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
P516TR-ND
7
J1, J2, J3, J4
DigiKey Part No.
Comment
DNP: C1, C2
DNP: C10, C12
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder.
16-pin header, TH
SAM1029-16-ND
: Header
SAM1213-16-ND
: Receptacle
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
JP5, JP6,
JP7, JP8,
JP9, JP10
6
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3
10
JP1, JP2,
JP4
3
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
11
JP3
1
3-pin header, male, TH
SAM1035-03-ND
place jumper on pins 1-2
10
Jumper
15-38-1024-ND
Place on: JP1, JP2, JP3,
JP4, JP5, JP6, JP7, JP8,
JP9, JP10
12
84
4
Description
13
JTAG
1
14-pin connector, male, TH
HRP14H-ND
14
Q1
0
Crystal
Q1: Micro Crystal MS1V-T1K
DNP: Q1
32.768kHz, C(Load) =
Keep vias free of solder"
12.5pF
15
Q2
1
Crystal
Q2: 4MHz Buerklin: 78D134
16
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
17
R1, R2, R4,
R6, R8, R9,
R12
2
0 Ω, SMD0805
541-000ATR-ND
18
R10
1
100 Ω, SMD0805
Buerklin: 07E500
18
R11
1
1M Ω, SMD0805
18
R5
1
47k Ω, SMD0805
19
U1
1
Socket: QFN11T064-006
Manuf.: Yamaichi
20
PCB
1
79 x 77 mm
2 layers
21
Rubber stand
off
4
22
MSP430
2
MSP430F5509 RGC
23
Insulating
disk to Q2
1
Insulating disk to Q2
http://www.ettinger.de/Art_De
tail.cfm?ART_ARTNUM=70.0
8.121
27
C33
1
220n SMD0603
Buerklin: 53D2074
28
C35
1
10p SMD0603
Buerklin: 56D102
29
C36
1
10p SMD0603
Buerklin: 56D102
30
C38
1
220n SMD0603
Buerklin: 53D2074
31
C39
1
4u7 SMD0603
Buerklin: 53D2086
32
C40
1
0.1u SMD0603
Buerklin: 53D2068
33
D2, D3, D4
3
LL103A
Buerklin: 24S3406
DNP: R4, R6, R8, R9, R12
541-47000ATR-ND
Buerklin: 20H1724
apply to corners at bottom
side
DNP: enclosed with kit. Is
supplied by TI
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430RGC64USB
www.ti.com
Table B-18. MSP-TS430RGC64USB Bill of Materials (continued)
Ref Des
No. Per
Board
34
IC7
1
TPD4E004
36
LED
0
JP3QE
SAM1032-03-ND
DNP
37
LED1
0
LEDCHIPLED_0603
FARNELL: 852-9833
DNP
38
LED2
0
LEDCHIPLED_0603
FARNELL: 852-9868
DNP
39
LED3
0
LEDCHIPLED_0603
FARNELL: 852-9841
DNP
40
R13, R15,
R16
0
470R
Buerklin: 07E564
DNP
41
R33
1
1k4 / 1k5
Buerklin: 07E612
42
R34
1
27R
Buerklin: 07E444
43
R35
1
27R
Buerklin: 07E444
44
R36
1
33k
Buerklin: 07E740
45
S1
0
PB
P12225STB-ND
DNP
46
S2
0
PB
P12225STB-ND
DNP
46
S3
1
PB
P12225STB-ND
47
USB1
1
USB_RECEPTACLE
FARNELL: 117-7885
Pos.
Description
DigiKey Part No.
Comment
Manu: TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
85
MSP-TS430PN80
www.ti.com
B.18 MSP-TS430PN80
NOTE: For MSP430F(G)47x devices:
Connect pins 7 and 10 (GND) externally to DVSS (see data sheet).
Connect load capacitance on Vref pin 60 when SD16 is used (see data sheet).
Figure B-35. MSP-TS430PN80 Target Socket Module, Schematic
86
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PN80
www.ti.com
LED connected to pin 12
Connector J5
External power connection
Remove R8 and jumper R9
Jumper J6
Open to disconnect LED
Orient Pin 1 of MSP430 device
Figure B-36. MSP-TS430PN80 Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
87
MSP-TS430PN80
www.ti.com
Table B-19. MSP-TS430PN80 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP: C1, C2
1.1
C3, C4
0
47pF, SMD0805
DNP: Only
recommendation. Check
your crystal spec.
2
C6, C7
1
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5
1
100nF, SMD0805
478-3351-2-ND
4
C8
1
10nF, SMD0805
478-1383-2-ND
5
D1
1
green LED, SMD0603
475-1056-2-ND
DigiKey Part No.
Comment
6
J1, J2, J3,
J4
0
25-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1029-20-NDSAM1213kit.Keep vias free of
20-ND
solder.: Header:
Receptacle
7
J5, JP1
2
3-pin header, male, TH
SAM1035-03-ND
8
J6, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
3
Jumper
15-38-1024-ND
Place on: J6, JP2,
JP1/Pos1-2
HRP14H-ND
9
88
Description
10
JTAG
1
14-pin connector, male, TH
11
BOOTST
0
10-pin connector, male, TH
12
Q1, Q2
0
Crystal
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
13
R3
1
560 Ω, SMD0805
541-560ATR-ND
14
R1, R2, R4,
R6, R7, R10,
R11, R12
2
0 Ω, SMD0805
541-000ATR-ND
15
R5
1
47k Ω, SMD0805
541-47000ATR-ND
16
U1
1
Socket: IC201-0804-014
17
PCB
1
77 x 77 mm
18
Adhesive
Plastic feet
4
~6mm width, 2mm height
19
MSP430
2
MSP430FG439IPN
DNP: Keep vias free of
solder
DNP: Keep vias free of
solder
DNP: R4, R6, R7, R10,
R11, R12
Manuf.: Yamaichi
2 layers
e.g., 3M Bumpons Part No.
SJ-5302
Hardware
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PN80A
www.ti.com
B.19 MSP-TS430PN80A
Figure B-37. MSP-TS430PN80A Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
89
MSP-TS430PN80A
www.ti.com
Jumpers JP5 to JP10
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
Connector J5
External power connector
Jumper JP3 to "ext"
Orient Pin 1 of MSP430 device
If the system should
be supplied via LDOI (J6),
close JP4 and
set JP3 to external
Jumper JP2
Open to disconnect LED
D1 LED connected to P1.0
Figure B-38. MSP-TS430PN80A Target Socket Module, PCB
90
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PN80USB
www.ti.com
Table B-20. MSP-TS430PN80A Bill of Materials
Position
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP
2
C3, C4
0
47pF, SMD0805
DNP
3
C6, C7,
C10, C12
3
10uF/6.3V, SMD0805
DNP C10
4
C5, C11,
C13, C14,
C15
5
100nF, SMD0805
5
C8
1
2.2nF, SMD0805
6
C9
1
470nF, SMD0805
7
C16
1
4.7uF, SMD0805
8
C17
1
220nF, SMD0805
9
D1
1
green LED, SMD0805
P516TR-ND
10
J1, J2, J3,
J4
0
20-pin header, TH
SAM1029-20-ND
(Header)
SAM1213-20-ND
(Receptacle)
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder:
11
J5 , J6
2
3-pin header, male, TH
12
JP3, JP5,
JP6, JP7,
JP8, JP9,
JP10
7
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3 on JP5,
JP6, JP7, JP8, JP9, JP10 place
jumpers on pins 1-2 on JP3,
13
JP1, JP2,
JP4
3
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
10
Jumper
15-38-1024-ND
See Pos. 12 and Pos. 13
HRP14H-ND
14
Description
DigiKey Part No.
Comment
311-1245-2-ND
478-1403-2-ND
15
JTAG
1
14-pin connector, male,
TH
16
BOOTST
0
10-pin connector, male,
TH
17
Q1
0
Crystal
Micro Crystal MS3V-T1R
32.768kHz, C(Load) =
DNP: Q1 Keep vias free of solder
12.5pF
18
Q2
0
Crystal
Q2: 4MHz Buerklin:
78D134
19
Insulating
disk to Q2
0
Insulating disk to Q2
http://www.ettinger.de/Ar
t_Detail.cfm?ART_ART
NUM=70.08.121
20
D3,D4
2
LL103A
Buerklin: 24S3406
21
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
22
R1, R2,
R4, R6,
R8,
R9,R10,
R11, R12
3
0 Ohm, SMD0805
541-000ATR-ND
23
R5
1
47k Ω, SMD0805
541-47000ATR-ND
24
U1
1
Socket:IC201-0804-014
Manuf.: Yamaichi
25
PCB
1
77 x 91 mm
2 layers
26
Adhesive
plastic feet
4
about 6mm width, 2mm
height
27
MSP430
2
MSP430F5329IPN
"DNP Keep vias free of solder"
e.g., 3M Bumpons Part
No. SJ-5302
DNP: Q2 Keep vias free of solder
DNP: R6, R8, R9, R10, R11,R12
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
B.20 MSP-TS430PN80USB
Due to the use of diodes in the power chain, the voltage on the MSP430F5xx device is approximately
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
91
MSP-TS430PN80USB
www.ti.com
NOTE: R11 should be populated.
Figure B-39. MSP-TS430PN80USB Target Socket Module, Schematic
92
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PN80USB
www.ti.com
Jumper JP3
1-2 (int): Power supply via JTAG debug interface
2-3 (ext): External power supply
USB Connector
Jumper JP1
Open to measure current
Connector J5
External power connector
Jumper JP3 to ‘ext’
Jumper JP4
Close for USB bus powered
device
Jumper JP5 to JP10
Close 1-2 to debug in Spy-BiWire mode.
Close 2-3 to debug in 4-wire
JTAG mode.
BSL invoke button S3
LED connected to P1.0
Jumper JP2
Open to disconnect LED
Figure B-40. MSP-TS430PN80USB Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
93
MSP-TS430PN80USB
www.ti.com
Table B-21. MSP-TS430PN80USB Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
1.1
C3, C4
2
47pF, SMD0805
2
C6, C7
2
10uF/6.3V, Tantal Size B
511-1463-2-ND
3
C5, C11,
C13, C14
4
100nF, SMD0805
311-1245-2-ND
3.1
C10, C12
0
10uF, SMD0805
311-1245-2-ND
4
C8
1
2.2nF, SMD0805
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
P516TR-ND
7
J1, J2, J3,
J4
7.1
20-pin header, TH
DigiKey Part No.
Comment
DNP: C1, C2
DNP: C10, C12
SAM1029-20-ND
DNP: headers and
receptacles enclosed with
kit. Keep vias free of
solder.: Header:
Receptacle
DNP: headers and
receptacles enclosed with
kit. Keep vias free of
solder.: Header:
Receptacle
4
20-pin header, TH
SAM1213-20-ND
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
JP5, JP6,
JP7,
JP8,JP9,
JP10
6
3-pin header, male, TH
SAM1035-03-ND
Place jumpers on pins 2-3
10
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
JP4
1
SAM1035-02-ND
Place jumper only on one
pin
JP3
1
3-pin header, male, TH
SAM1035-03-ND
Place jumper on pins 1-2
10
Jumper
15-38-1024-ND
Place on: JP1, JP2, JP3,
JP4, JP5, JP6, JP7, JP8,
JP9, JP10
11
12
94
4
Description
13
JTAG
1
14-pin connector, male, TH
HRP14H-ND
14
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
15
Q2
1
Crystal
"Q2: 4MHzBuerklin:
78D134"
16
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
17
R1, R2, R4,
R6, R8, R9,
R12
2
0 Ω, SMD0805
541-000ATR-ND
18
R10
1
100 Ω, SMD0805
Buerklin: 07E500
18
R11
0
1M Ω, SMD0805
18
R5
1
47k Ω, SMD0805
19
U1
1
Socket:IC201-0804-014
Manuf.: Yamaichi
20
PCB
1
79 x 77 mm
2 layers
21
Rubber
standoff
4
22
MSP430
2
MSP430F5529
23
Insulating
disk to Q2
1
Insulating disk to Q2
http://www.ettinger.de/Art_
Detail.cfm?ART_ARTNUM
=70.08.121
27
C33
1
220n
Buerklin: 53D2074
28
C35
1
10p
Buerklin: 56D102
DNP: Q1 Keep vias free of
solder
DNP: R4, R6, R8, R9, R12
DNP
541-47000ATR-ND
Buerklin: 20H1724
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PN80USB
www.ti.com
Table B-21. MSP-TS430PN80USB Bill of Materials (continued)
Pos.
Ref Des
No. per
Board
29
C36
1
10p
Buerklin: 56D102
30
C38
1
220n
Buerklin: 53D2074
31
C39
1
4u7
Buerklin: 53D2086
32
C40
1
0.1u
Buerklin: 53D2068
33
D2, D3, D4
3
LL103A
Buerklin: 24S3406
34
IC7
1
TPD4E004
36
LED
0
JP3QE
SAM1032-03-ND
DNP
37
LED1
0
LEDCHIPLED_0603
FARNELL: 852-9833
DNP
38
LED2
0
LEDCHIPLED_0603
FARNELL: 852-9868
DNP
39
LED3
0
LEDCHIPLED_0603
FARNELL: 852-9841
DNP
40
R13, R15,
R16
0
470R
Buerklin: 07E564
DNP
41
R33
1
1k4
Buerklin: 07E612
42
R34
1
27R
Buerklin: 07E444
43
R35
1
27R
Buerklin: 07E444
44
R36
1
33k
Buerklin: 07E740
45
S1
0
PB
P12225STB-ND
DNP
46
S2
0
PB
P12225STB-ND
DNP
46
S3
1
PB
P12225STB-ND
47
USB1
1
USB_RECEPTACLE
FARNELL: 117-7885
Description
DigiKey Part No.
Comment
Manu: TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
95
MSP-TS430PZ100
www.ti.com
B.21 MSP-TS430PZ100
NOTE: Connections between the JTAG header and pins XOUT and XIN are no longer required and should not be
made.
Figure B-41. MSP-TS430PZ100 Target Socket Module, Schematic
96
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100
www.ti.com
Jumper J6
Open to disconnect LED
Jumper J7
Open to measure current
LED connected to pin 12
Connector J5
External power connection
Remove R8 and jumper R9
Orient Pin 1 of MSP430 device
Figure B-42. MSP-TS430PZ100 Target Socket Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
97
MSP-TS430PZ100
www.ti.com
Table B-22. MSP-TS430PZ100 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2,
0
12pF, SMD0805
DNP
1b
C3, C4
0
47pF, SMD0805
DNP: Only
recommendation. Check
your crystal spec.
2
C6, C7
1
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5
1
100nF, SMD0805
478-3351-2-ND
4
C8
1
10nF, SMD0805
478-1383-2-ND
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
yellow LED, TH, 3mm, T1
511-1251-ND
7
J1, J2, J3,
J4
0
25-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1029-25-NDSAM1213kit.Keep vias free of
25-ND
solder.: Header:
Receptacle
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
J6, J7
2
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
2
Jumper
15-38-1024-ND
Place on: J6, J7
HRP14H-ND
10
98
Description
DigiKey Part No.
Comment
DNP: C6
11
JTAG
1
14-pin connector, male, TH
12
BOOTST
0
10-pin connector, male, TH
13
Q1, Q2
0
Crystal
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
14
R3
1
330 Ω, SMD0805
541-330ATR-ND
15
R1, R2, R4,
R8, R9, R10,
R11, R12
3
0 Ω, SMD0805
541-000ATR-ND
16
R5
1
47k Ω, SMD0805
541-47000ATR-ND
17
U1
1
"Socket: IC201-1004-008or
IC357-1004-53N"
Manuf.: Yamaichi
18
PCB
1
82 x 90 mm
2 layers
19
Adhesive
Plastic feet
4
~6mm width, 2mm height
20
MSP430
2
MSP430FG4619IPZ
DNP: Keep vias free of
solder
e.g., 3M Bumpons Part No.
SJ-5302
Hardware
DNP: Keep vias free of
solder
DNP: R4, R9, R10, R12
Apply to corners at bottom
side
DNP: enclosed with kit
supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100A
www.ti.com
B.22 MSP-TS430PZ100A
Figure B-43. MSP-TS430PZ100A Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
99
MSP-TS430PZ100A
www.ti.com
Jumper JP3
1-2 (int): Power supply via JTAG interface
2-3 (ext): External Power Supply
Jumper JP1
Open to measure current
Jumper JP2
Open to disconnect LED
LED D1 connected to P5.1
Orient Pin 1 of Device
Figure B-44. MSP-TS430PZ100A Target Socket Module, PCB
100 Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100A
www.ti.com
Table B-23. MSP-TS430PZ100A Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
DNP
1b
C3, C4
0
47pF, SMD0805
DNP: Only
recommendation. Check
your crystal spec.
2
C7, C9
2
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5, C11,
C14
3
100nF, SMD0805
311-1245-2-ND
4
C8
1
10nF, SMD0805
478-1358-1-ND
5
C6
0
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
67-1553-1-ND
7
J1, J2, J3,
J4
0
25-pin header, TH
DNP: Headers and
receptacles enclosed with
SAM1029-25-NDSAM1213kit.Keep vias free of
25-ND
solder.: Header:
Receptacle
Description
DigiKey Part No.
Comment
DNP
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
10
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
pPlace jumper on header
11
JP3
1
3-pin header, male, TH
SAM1035-03-ND
Place jumper on pins 1-2
3
Jumper
15-38-1024-ND
Place on: JP1, JP2, JP3
HRP14H-ND
12
13
JTAG
1
14-pin connector, male, TH
14
BOOTST
0
10-pin connector, male, TH
15
Q1, Q2
0
Crystal
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
16
R3
1
330 Ω, SMD0805
541-330ATR-ND
17
R1, R2, R4,
R6, R7, R8,
R9, R10,
R11, R12
2
0 Ω, SMD0805
541-000ATR-ND
18
R5
1
47k Ω, SMD0805
541-47000ATR-ND
19
U1
1
Socket: IC357-1004-53N
Manuf.: Yamaichi
20
PCB
1
90 x 82 mm
4 layers
21
Rubber
standoff
4
22
MSP430
2
DNP: Keep vias free of
solder
Select appropriate
MSP430F5438IPZ
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP: Keep vias free of
solder
DNP: R4, R6, R7, R8, R9,
R10, R11, R12
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
Hardware
© 2009–2010, Texas Instruments Incorporated
101
MSP-TS430PZ100B
www.ti.com
B.23 MSP-TS430PZ100B
Figure B-45. MSP-TS430PZ100B Target Socket Module, Schematic
102
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100B
www.ti.com
Connector J5
External power connector
Jumper JP1 to "ext"
Jumper JP1
Open to measure current
Orient Pin 1 of MSP430 device
JP11, JP12, JP13
Connect 1-2 to connect
AUXVCCx with DVCC or
drive AUXVCCx externally
Jumpers JP5 to JP10
Close 1-2 to debug in Spy-Bi-Wire mode
Close 2-3 to debug in 4-wire JTAG mode
D1 LED connected to P1.0
Jumper JP2
Open to disconnect LED
Figure B-46. MSP-TS430PZ100B Target Socket Module, PCB
Hardware 103
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100B
www.ti.com
Table B-24. MSP-TS430PZ100B Bill of Materials
Ref Des
No. per
Board
1
C1, C2
0
12pF, SMD0805
2
C4, C5, C6
, C7, C8,
C9
6
100nF, SMD0805
311-1245-2-ND
3
C10, C26
2
470 nF, SMD0805
478-1403-2-ND
4
C11, C12
1
10 uF / 6.3 V SMD0805
5
C13, C14,
C16, C18,
C19, C29
6
4.7 uF SMD0805
6
D1
1
green LED, SMD0805
P516TR-ND
7
J1, J2, J3,
J4
0
25-pin header, TH
SAM1029-25-ND
(Header)
SAM1213-25-ND
(Receptacle)
DNP: Headers and receptacles
enclosed with kit. Keep vias free of
solder:
8
J5
1
3-pin header, male, TH
9
JP3, JP5,
JP6, JP7,
JP8, JP9,
JP10
7
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3 on JP5,
JP6, JP7, JP8, JP9, JP10 place
jumpers on pins 1-2 on JP3,
10
JP1, JP2,
JP4
3
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
11
JP11,
JP12, JP13
3
4-pin header, male, TH
13
Jumper
15-38-1024-ND
HRP14H-ND
Position
12
104
Description
DigiKey Part No.
Comment
DNP
C12 DNP
place jumper on header 1-2
See Pos. 9 and Pos. 10 and Pos. 11
15
JTAG
1
14-pin connector, male,
TH
16
BOOTST
0
10-pin connector, male,
TH
17
Q1
0
Crystal
21
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
22
R1, R2,
R4, R6,
R8, R10,
R11
2
0 Ohm, SMD0805
541-000ATR-ND
23
R5
1
47k Ω, SMD0805
541-47000ATR-ND
24
U1
1
Socket: IC357-1004-53N
25
PCB
1
90 x 82 mm
26
Adhesive
plastic feet
4
about 6mm width, 2mm
height
27
MSP430
2
MSP430F6733IPZ
"DNP Keep vias free of solder"
DNP: Q1 Keep vias free of solder
DNP: R4, R6, R8, R10, R11
Manuf.: Yamaichi
2 layers
e.g., 3M Bumpons Part
No. SJ-5302
Hardware
Apply to corners at bottom side
DNP: enclosed with kit, supplied by TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ5x100
www.ti.com
B.24 MSP-TS430PZ5x100
Figure B-47. MSP-TS430PZ5x100 Target Socket Module, Schematic
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
105
MSP-TS430PZ5x100
www.ti.com
Jumper JP3
1-2 (int): Power supply via JTAG debug interface
2-3 (ext): External power supply
Connector J5
External power connector
Jumper J3 to ‘ext’
Jumper JP1
Open to measure current
Jumpers JP5 to JP10
Close 1-2 to debug in
Spy-Bi-Wire mode.
Close 2-3 to debug in
4-wire JTAG mode.
LED connected to P1.0
Jumper JP2
Open to disconnect LED
Figure B-48. MSP-TS430PZ5x100 Target Socket Module, PCB
106 Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100USB
www.ti.com
Table B-25. MSP-TS430PZ5x100 Bill of Materials
Pos.
Ref Des
No. per
Board
1
C1, C2
0
1b
C3, C4
Description
DigiKey Part No.
Comment
12pF, SMD0805
DNP
47pF, SMD0805
DNP: Only
recommendation. Check
your crystal spec.
2
C6, C7
2
10uF/10V, Tantal Size B
511-1463-2-ND
3
C5, C10,
C11,
C12,C13,
C14
4
100nF, SMD0805
311-1245-2-ND
4
C8
0
2.2nF, SMD0805
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
67-1553-1-ND
DNP: C12, C14
DNP
DNP: headers and
receptacles enclosed with
kit. Keep vias free of
solder.: Header:
Receptacle
J1, J2, J3,
J4
0
25-pin header, TH
"SAM1029-25NDSAM1213-25-ND"
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
JP5, JP6,
JP7,
JP8,JP9,
JP10
6
3-pin header, male, TH
SAM1035-03-ND
Place jumpers on pins 2-3
10
JP1, JP2
2
2-pin header, male, TH
SAM1035-02-ND
Place jumper on header
11
JP3
1
3-pin header, male, TH
SAM1035-03-ND
Place jumper on pins 1-2
9
Jumper
15-38-1024-ND
Place on JP1, JP2, JP3,
JP5, JP6, JP7, JP8, JP9,
JP10
HRP14H-ND
7
12
13
JTAG
1
14-pin connector, male, TH
14
BOOTST
0
10-pin connector, male, TH
15
Q1, Q2
0
Crystal
Q1: Micro Crystal
MS1V-T1K 32.768kHz,
C(Load) = 12.5pF
16
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
17
R1, R2, R4,
R6, R8, R9,
R10, R11,
R12
3
0 Ω, SMD0805
541-000ATR-ND
18
R5
1
47k Ω, SMD0805
541-47000ATR-ND
19
U1
1
Socket: IC357-1004-53N
Manuf.: Yamaichi
20
PCB
1
90 x 82 mm
2 layers
21
Rubber
standoff
4
22
MSP430
2
DNP: Keep vias free of
solder
Select appropriate
MSP430F5438IPZ
DNP: Keep vias free of
solder
DNP: R6, R8, R9, R10,
R11, R12
Apply to corners at bottom
side
DNP: Enclosed with kit
supplied by TI
B.25 MSP-TS430PZ100USB
Due to the use of diodes in the power chain, the voltage on the MSP430F5xx device is approximately
0.3 V lower than is set by the debugging tool. Set the voltage in the IDE to 0.3 V higher than desired; for
example, to run the MCU at 3.0 V, set it to 3.3 V.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
107
MSP-TS430PZ100USB
www.ti.com
Figure B-49. MSP-TS430PZ100USB Target Socket Module, Schematic
108
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100USB
www.ti.com
Figure B-50. MSP-TS430PZ100USB Target Socket Module, PCB
Hardware 109
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100USB
www.ti.com
Table B-26. MSP-TS430PZ100USB Bill of Materials
Pos.
Ref Des
No. Per
Board
1
C1, C2
0
12pF, SMD0805
1.1
C3, C4
2
47pF, SMD0805
2
C6, C7
2
10uF/6.3V, Tantal Size B
511-1463-2-ND
3
C5, C11,
C13, C14,
C19
5
100nF, SMD0805
311-1245-2-ND
3.1
C10, C12,
C18,17
0
100nF, SMD0805
311-1245-2-ND
4
C8
1
2.2nF, SMD0805
5
C9
1
470nF, SMD0805
478-1403-2-ND
6
D1
1
green LED, SMD0805
P516TR-ND
7
J1, J2, J3, J4
7.1
4
Description
25-pin header, TH
DigiKey Part No.
Comment
DNP: C1, C2
DNP: C10, C12,C18, C17
SAM1029-25-ND
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder.
: Header
: Receptacle
DNP: headers and
receptacles enclosed with kit.
Keep vias free of solder.
: Header
: Receptacle
4
25-pin header, TH
SAM1213-25-ND
8
J5
1
3-pin header, male, TH
SAM1035-03-ND
9
JP5, JP6,
JP7, JP8,
JP9, JP10
6
3-pin header, male, TH
SAM1035-03-ND
place jumpers on pins 2-3
10
JP1, JP2,
JP4
3
2-pin header, male, TH
SAM1035-02-ND
place jumper on header
11
JP3
1
3-pin header, male, TH
SAM1035-03-ND
place jumper on pins 1-2
10
Jumper
15-38-1024-ND
Place on: JP1, JP2, JP3,
JP4, JP5, JP6, JP7, JP8,
JP9, JP10
12
13
JTAG
1
14-pin connector, male, TH
HRP14H-ND
14
Q1
0
Crystal
Micro Crystal MS1V-T1K
32.768kHz, C(Load) =
12.5pF
15
Q2
1
Crystal
Q2: 4MHz, Buerklin: 78D134
16
R3, R7
2
330 Ω, SMD0805
541-330ATR-ND
17
R1, R2, R4,
R6, R8, R9,
R12
3
0 Ω, SMD0805
541-000ATR-ND
18
R10
1
100 Ω, SMD0805
Buerklin: 07E500
18
R11
1
1M Ω, SMD0603
18
R5
1
47k Ω, SMD0805
19
U1
1
Socket:IC201-1004-008
Manuf.: Yamaichi
20
PCB
1
79 x 77 mm
2 layers
21
Rubber stand
off
4
22
MSP430
2
MSP430F5529
23
nsulating disk
to Q2
1
Insulating disk to Q2
24
C16
1
4.7 nF SMD0603
27
C33
1
220n SMD0603
Buerklin: 53D2074
28
C35, C36
2
10p SMD0603
Buerklin: 56D102
DNP: Q1. Keep vias free of
solder
DNP: R6, R8, R9, R12
not existing in Rev 1.0
541-47000ATR-ND
Buerklin: 20H1724
apply to corners at bottom
side
DNP: enclosed with kit. Is
supplied by TI
http://www.ettinger.de/Art_De
tail.cfm?ART_ARTNUM=70.0
8.121
110 Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-TS430PZ100USB
www.ti.com
Table B-26. MSP-TS430PZ100USB Bill of Materials (continued)
Pos.
Ref Des
No. Per
Board
30
C38
1
220n SMD0603
Buerklin: 53D2074
31
C39
1
4u7 SMD0603
Buerklin: 53D2086
32
C40
1
0.1u SMD0603
Buerklin: 53D2068
33
D2, D3, D4
3
LL103A
Buerklin: 24S3406
34
IC7
1
TPD4E004
35
LED
0
JP3QE
SAM1032-03-ND
DNP
36
LED1, LED2,
LED3
0
LEDCHIPLED_0603
FARNELL: 852-9833
DNP
37
R13, R15,
R16
0
470R SMD0603
Buerklin: 07E564
DNP
38
R33
1
1k4 / 1k5 SMD0603
Buerklin: 07E612
39
R34
1
27R SMD0603
Buerklin: 07E444
40
R35
1
27R SMD0603
Buerklin: 07E444
41
R36
1
33k SMD0603
Buerklin: 07E740
42
S1, S2, S3
1
PB
P12225STB-ND
43
USB1
1
USB_RECEPTACLE
FARNELL: 117-7885
44
JP11
1
4-pin header, male, TH
SAM1035-04-ND
Description
DigiKey Part No.
Comment
Manu: TI
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
DNP S1 and S2. (Only S3)
place jumper only on Pin 1
Hardware
© 2009–2010, Texas Instruments Incorporated
111
(May be addedclose
to therespective pins
to reduce emissions
at 5GHz tole vel
required byETSI)
Power Management
VCC01 = external VCC
= DVCC
= AVDD_RF / AVCC_RF
Vdd
Vdda1
= AVCC
© 2009–2010, Texas Instruments Incorporated
Vdda2
Port connectors
CON1 ..
CON3 = Port1 .. Port3 of cc430
CON4 = spare
CON5 = 1: XIN 2: XOUT
CON6 = Vdd, GND, Vcore,
COM0, LCDCAP
CON7 = Vdda1, Vdda2, GND,
AGND
CON8 = JTAG_BASE
(JTAG Port)
CON9 = Vdd, GND, AGND
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
112
www.ti.com
EM430F5137RF900
B.26 EM430F5137RF900
Figure B-51. EM430F5137RF900 Target Socket Module, Schematic
EM430F5137RF900
www.ti.com
JTAG connector
Jumper JP2
Close EXT for external supply
Close INT for JTAG supply
Open to measure current
jumper JP3
External power connector
CON12
Jumper JP1
Spy-Bi-Wire mode
VCC
GND
GND
Jumper JP1
Close JTAG
position to
debug in
JTAG mode
Open to disconnect LEDs
jumper JP5/JP10
LED D2 (red) connected to
P3.6 via JP10
Close SBW position
to debug in
Spy-Bi-Wire mode
Push-button S2
connected to P1.7
LED D1 (green) connected
to P1.0 via JP5
Footprint for 32kHz crystal
Use 0Ω resistor for R431/R441
to make XIN/XOUT available
on connector port5
RF - Crystal Q1 26 MHz
Reset button S1
RF - Signal SMA
Figure B-52. EM430F5137RF900 Target Socket Module, PCB
Hardware 113
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
EM430F5137RF900
www.ti.com
Table B-27. EM430F5137RF900 Bill of Materials
Item
Reference
No. per
Board
Description
Value
1
Q1
1
( CUSTOMER SUPPLY ) CRYSTAL,
SMT, 4P, 26MHz
26M
ASX-531(CS)
AKER
ELECTRONIC
2
C1-C5,
C082, C222,
C271, C281,
C311, C321,
C341, C412,
C452
14
CAPACITOR, SMT, 0402, CER,
16V, 10%, 0.1uF
0.1uF
0402YC104KAT2
A
AVX
3
C071
1
CAPACITOR, SMT, 0603,
CERAMIC, 0.47uF, 16V, 10%, X5R
0.47uF
0603YD474KAT2
A
AVX
4
R401
1
RES0402, 47.0K
5
CON11
1
HEADER, THU, MALE, 14P, 2X7,
25.4x9.2x9.45mm
09 18 514 6323
HARTING
6
CON10
0
HEADER, THU, MALE, 10P, 2X5,
20.32x9.2x9.45mm
09 18 510 6323
HARTING
7
D1
1
LED, SMT, 0603, GREEN, 2.1V
active
APT1608MGC
KINGBRIGHT
8
D2
1
LED, SMT, 0603, RED, 2.0V
active
APT1608EC
KINGBRIGHT
47kΩ
Manufacturer's
Part Number
Manufacturer
CRCW04024702F
DALE
100
9
Q3
0
UNINSTALLED CRYSTAL, SMT, 3P,
MS1V (Customer Supply)
10
CON12
1
HEADER, THU, MALE, 3P, 1x3,
9.9x4.9x5.9mm
11
C251, C261
2
50V, 5%, 27pF
12
L341
1
FERRITE, SMT, 0402, 1.0kΩ,
250mA
13
C293
1
CAPACITOR, SMT, 0402,
CERAMIC, 100pF, 50V, 0.25pF,
C0G(NP0)
14
L304
1
INDUCTOR, SMT, 0402, 2.2nH,
0.1nH, 220mA, 500MHz
0.0022u LQP15MN2N2B0
H
2
MURATA
15
L303, L305
2
INDUCTOR, SMT, 0402, 15nH, 2%,
450mA, 250MHz
0.015uH
LQW15AN15NG0
0
MURATA
16
L292, L302
2
INDUCTOR, SMT, 0402, 18nH, 2%,
370mA, 250MHz
0.018uH
LQW15AN18NG0
0
MURATA
17
C291
1
CAPACITOR, SMT, 0402,
CERAMIC, 1pF, 50V, 0.05pF,
C0G(NP0)
1pF
GRM1555C1H1R
0WZ01
MURATA
18
C303
1
CAPACITOR, SMT, 0402,
CERAMIC, 8.2pF, 50V, 0.05pF,
C0G(NP0)
8.2pF
GRM1555C1H8R
2WZ01
MURATA
19
C292,
C301-C302,
C304
4
CAPACITOR, SMT, 0402,
CERAMIC, 1.5pF, 50V, 0.05pF,
C0G(NP0)
1.5pF
GRM1555C1H1R
5WZ01
MURATA
20
L291, L301
2
INDUCTOR, SMT, 0402, 12nH, 2%,
500mA, 250MHz
0.012uH
LQW15AN12NG0
0
MURATA
21
C282, C312,
C351, C361,
C371
5
CAPACITOR, SMT, 0402,
CERAMIC, 2pF, 50V, 0.1pF, C0G
2.0pF
GRM1555C1H2R
0BZ01
Murata
22
L1
1
INDUCTOR, SMT, 0402, 6.2nH,
0.1nH, 130mA, 500MHz
6.2nH
LQP15MN6N2B0
2
Murata
23
S1-S2
2
ULTRA-SMALL TACTILE SWITCH,
SMT, 2P, SPST-NO, 1.2x3x2.5mm,
0.05A, 12V
B3U-1000P
OMRON
24
R4-R5,
R051, R061,
R431, R441
0
UNINSTALLED
RESISTOR/JUMPER, SMT, 0402, 0
Ω, 5%, 1/16W
ERJ-2GE0R00X
PANASONIC
32.768k MS1V-T1K (UN)
MICRO
CRYSTAL
22-03-5035
MOLEX
27pF
GRM36COG270J
50
MURATA
1kΩ
BLM15HG102SN
1D
MURATA
100pF
0Ω
114 Hardware
Comment
DNP
DNP
GRM1555C1H101
MURATA
JZ01
DNP
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
EM430F5137RF900
www.ti.com
Table B-27. EM430F5137RF900 Bill of Materials (continued)
Item
Reference
No. per
Board
Description
Value
Manufacturer's
Part Number
24a
R7
1
RESISTOR/JUMPER, SMT, 0402, 0
Ω, 5%, 1/16W
0Ω
25
R2-R3, R6
3
RESISTOR, SMT, 0402, THICK
FILM, 5%, 1/16W, 330
26
C431, C441
0
CAPACITOR, SMT, 0402, CER,
12pF, 50V, 5%, NPO
27
C401
1
CAPACITOR, SMT, 0402, CER,
2200pF, 50V, 10%, X7R
28
R331
1
RESISTOR, SMT, THICK FILM, 56K,
1/16W, 5%
56kΩ
ERJ-2GEJ563
PANASONIC
29
C081, C221,
C411, C451
4
CAPACITOR, SMT, 0603,
CERAMIC, 10uF, 6.3V, 20%, X5R
10uF
ECJ-1VB0J106M
PANASONIC
30
R1
1
RESISTOR/JUMPER, SMT, 0402, 0
Ω, 5%, 1/16W
0Ω
ERJ-2GE0R00X
PANASONIC
31
C041
0
UNINSTALLED CAP CERAMIC
4.7UF 6.3V X5R 0603
4.7uF
ECJ-1VB0J475K
Panasonic
32
X1
1
SMA STRIGHT JACK, SMT
32K10A-40ML5
ROSENBERG
ER
33
Q2
0
Crystal, SMT, 32.768 kHz
34
U1
1
DUT, SMT, PQFP, RGZ-48,
0.5mmLS, 7.15x7.15x1mm,
THRM.PAD
CC430F52x1
TI
35
JP1
1
Pin Connector 2x4pin
61300821121
WUERTH
36
CON1CON9
0
Pin Connector 2x4pin
61300821121
WUERTH
37
JP2
1
Pin Connector 1x3pin
61300311121
WUERTH
38
JP3, JP5,
JP10
3
Pin Connector 1x2pin
61300211121
WUERTH
38a
JP7, CON13
0
Pin Connector 1x2pin
61300211121
WUERTH
DNP
39
JP4
1
Pin Connector 2x2pin
61300421121
WUERTH
DNP
40
JP1a
1
Pin Connector 2x3pin
61300621121
WUERTH
Manufacturer
ERJ-2GE0R00X
PANASONIC
330Ω
ERJ-2GEJ331
PANASONIC
12pF
ECJ-0EC1H120J
PANASONIC
0.0022u
ECJ-0EB1H222K
F
PANASONIC
32.768k MS3V-T1R
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Comment
DNP
Micro Crystal
DNP
DNP
Hardware
© 2009–2010, Texas Instruments Incorporated
115
(May beaddedclose
to therespective pins
to reduce emissions
at 5GHz to el vel
required by ETSI)
Power Management
VCC01 = external VCC
= AVDD_RF / AVCC_RF
= DVCC
= AVCC
Vdd
Vdda1
© 2009–2010, Texas Instruments Incorporated
Vdda2
Port connectors
CON1 ..
CON5 = Port1 .. Port5 of cc430
CON6 = Vdd, GND, Vcore,
COM0, LCDCAP
CON7 = Vdda1, Vdda2, GND,
AGND
CON8 = JTAG_BASE
(JTAG Port)
CON9 = Vdd, GND, AGND
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
116
www.ti.com
EM430F6137RF900
B.27 EM430F6137RF900
Figure B-53. EM430F6137RF900 Target Socket Module, Schematic
EM430F6137RF900
www.ti.com
JTAG connector
Jumper JP2
Close EXT for external supply
Close INT for JTAG supply
Open to measure current
jumper JP3
External power connector
CON12
Jumper JP1
Spy-Bi-Wire mode
VCC
GND
GND
Jumper JP1
Close JTAG
position to
debug in
JTAG mode
Open to disconnect LEDs
jumper JP5/JP10
LED D2 (red) connected to
P3.6 via JP10
Close SBW position
to debug in
Spy-Bi-Wire mode
Push-button S2
connected to P1.7
LED D1 (green) connected
to P1.0 via JP5
Footprint for 32kHz crystal
Use 0Ω resistor for R541/R551
to makeP5.0/P5.1 available
on connector port5
RF - Crystal Q1 26 MHz
Reset button S1
C392
C422
L451
RF - Signal SMA
Figure B-54. EM430F6137RF900 Target Socket Module, PCB
Hardware 117
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
EM430F6137RF900
www.ti.com
Table B-28. EM430F6137RF900 Bill of Materials
Pos.
Ref Des
No.
per
Board
1
Q1
1
( CUSTOMER SUPPLY ) CRYSTAL, SMT,
4P, 26MHz
ASX-531(CS)
AKER
ELECTRONIC
2
C1-C5, C112,
C252, C381,
C391, C421,
C431, C451,
C522, C562
14
CAPACITOR, SMT, 0402, CER, 16V, 10%,
0.1uF
0402YC104KAT2A
AVX
3
C101
1
CAPACITOR, SMT, 0603, CERAMIC, 0.47uF,
0603YD474KAT2A
16V, 10%, X5R
AVX
4
R511
1
RES0402, 47.0K
CRCW04024702F100
DALE
09 18 514 6323
HARTING
Description
Part No.
Manufacturer
5
CON11
1
HEADER, THU, MALE, 14P, 2X7,
25.4x9.2x9.45mm, 90deg
7
D1
1
LED, SMT, 0603, GREEN, 2.1V
APT1608MGC
KINGBRIGHT
8
D2
1
LED, SMT, 0603, RED, 2.0V
APT1608EC
KINGBRIGHT
22-03-5035
MOLEX
10
CON12
1
HEADER, THU, MALE, 3P, 1x3,
9.9x4.9x5.9mm
11
C361, C371
2
50V, ±5%, 27pF
GRM36COG270J50
MURATA
12
L451
1
FERRITE, SMT, 0402, 1.0kΩ, 250mA
BLM15HG102SN1D
MURATA
GRM1555C1H101JZ01
MURATA
13
C403
1
CAPACITOR, SMT, 0402, CERAMIC, 100pF,
50V, ±0.25pF, C0G(NP0)
14
L414
1
INDUCTOR, SMT, 0402, 2.2nH, ±0.2nH,
1000mA, 250MHz
LQW15AN2N2C10
MURATA
15
L413, L415
2
INDUCTOR, SMT, 0402, 15nH, ±5%, 460mA,
LQW15AN15NJ00
250MHz
MURATA
16
L402, L412
2
INDUCTOR, SMT, 0402, 18nH, ±5%, 370mA,
LQW15AN18NJ00
250MHz
MURATA
17
C401
1
CAPACITOR, SMT, 0402, CER, 1pF, 50V,
±0.25pF, NP0
GJM1555C1H1R0CB01D
MURATA
18
C413
1
CAPACITOR, SMT, 0402, CERAMIC, 8.2pF,
50V, ±0.25pF, C0G(NP0)
GRM1555C1H8R2CZ01
MURATA
19
C402,
C411-C412,
C414
4
CAPACITOR, SMT, 0402, CERAMIC, 1.5pF,
50V, ±0.25pF, C0G(NP0)
GRM1555C1H1R5CZ01
MURATA
20
L401, L411
2
INDUCTOR, SMT, 0402, 12nH, ±5%, 500mA,
LQW15AN12NJ00
250MHz
MURATA
21
C46-C48,
C392, C422
5
CAPACITOR, SMT, 0402, CERAMIC, 2.0pF,
50V, ±0.25pF, C0G(NP0)
GRM1555C1H2R0CZ01
Murata
22
L1
1
INDUCTOR, SMT, 0402, 6.2nH, ±0.1nH,
700mA, 250MHz
LQW15AN6N2D00
Murata
23
S1-S2
2
ULTRA-SMALL TACTILE SWITCH, SMT, 2P,
SPST-NO, 1.2x3x2.5mm, 0.05A, 12V
B3U-1000P
OMRON
24
R7
1
RESISTOR/JUMPER, SMT, 0402, 0 Ω, 5%,
1/16W
ERJ-2GE0R00X (UN)
PANASONIC
25
R2-R3, R6
3
RESISTOR, SMT, 0402, THICK FILM, 5%,
1/16W, 330
ERJ-2GEJ331
PANASONIC
27
C511
1
CAPACITOR, SMT, 0402, CER, 2200pF,
50V, 10%, X7R
ECJ-0EB1H222K
PANASONIC
28
C111, C251,
C521, C561
4
CAPACITOR, SMT, 0603, CERAMIC, 10uF,
6.3V, 20%, X5R
ECJ-1VB0J106M
PANASONIC
28a
C041
1
CAP CERAMIC 4.7UF 6.3V X5R 0603
ECJ-1VB0J475M
PANASONIC
ERJ-2RKF5602
PANASONIC
29
R441
1
RESISTOR, SMT, THICK FILM, 56K, 1/16W,
1%
30
R1
1
RESISTOR/JUMPER, SMT, 0402, 0 Ω, 5%,
1/16W
ERJ-2GE0R00X
PANASONIC
31
X1
1
SMA STRIGHT JACK, SMT
32K10A-40ML5
ROSENBERGER
118 Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
EM430F6137RF900
www.ti.com
Table B-28. EM430F6137RF900 Bill of Materials (continued)
Pos.
Ref Des
No.
per
Board
33
U1
1
DUT, SMT, PQFP, RGC-64, 0.5mmLS,
9.15x9.15x1mm, THRM.PAD
CC430F6137
TI
34
JP1
1
Pin Connector 2x4pin
61300821121
WUERTH
Description
Part No.
Manufacturer
35
JP2
1
Pin Connector 1x3pin
61300311121
WUERTH
36a
JP3, JP5, JP10
3
Pin Connector 1x2pin
61300211121
WUERTH
38
JP1a
1
Pin Connector 2x3pin
61300621121
WUERTH
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
119
MSP-FET430PIF
www.ti.com
B.28 MSP-FET430PIF
Figure B-55. MSP-FET430PIF FET Interface Module, Schematic
120
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-FET430PIF
www.ti.com
Figure B-56. MSP-FET430PIF FET Interface Module, PCB
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
121
MSP-FET430UIF
www.ti.com
B.29 MSP-FET430UIF
Figure B-57. MSP-FET430UIF USB Interface, Schematic (1 of 4)
122
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-FET430UIF
www.ti.com
Figure B-58. MSP-FET430UIF USB Interface, Schematic (2 of 4)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
123
MSP-FET430UIF
www.ti.com
Figure B-59. MSP-FET430UIF USB Interface, Schematic (3 of 4)
124
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-FET430UIF
www.ti.com
Figure B-60. MSP-FET430UIF USB Interface, Schematic (4 of 4)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
125
MSP-FET430UIF
www.ti.com
Figure B-61. MSP-FET430UIF USB Interface, PCB
126
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
MSP-FET430UIF
www.ti.com
B.29.1 MSP-FET430UIF Revision History
Revision 1.3
• Initial released hardware version
Assembly change on 1.3 (May 2005)
• R29, R51, R42, R21, R22, R74: value changed from 330R to 100R
Changes 1.3 to 1.4 (Aug 2005)
• J5: VBUS and RESET additionally connected
• R29, R51, R42, R21, R22, R74: value changed from 330R to 100R
• U1, U7: F1612 can reset TUSB3410; R44 = 0R added
• TARGET-CON.: pins 6, 10, 12, 13, 14 disconnected from GND
• Firmware-upgrade option through BSL: R49, R52, R53, R54 added; R49, R52 are currently DNP
• Pullups on TCK and TMS: R78, R79 added
• U2: Changed from SN74LVC1G125DBV to SN74LVC1G07DBV
NOTE:
Using a locally powered target board with hardware revision 1.4
Using an MSP-FET430UIF interface hardware revision 1.4 with populated R62 in conjunction
with a locally powered target board is not possible. In this case, the target device RESET
signal is pulled down by the FET tool. It is recommended to remove R62 to eliminate this
restriction. This component is located close to the 14-pin connector on the MSP-FET430UIF
PCB. See the schematic and PCB drawings in this document for the exact location of this
component.
Assembly change on 1.4 (January 2006)
• R62: not populated
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware
© 2009–2010, Texas Instruments Incorporated
127
128
Hardware
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Appendix C
SLAU278F – May 2009 – Revised December 2010
Hardware Installation Guide
This section describes the hardware installation process of the following USB debug interfaces on a PC
running Windows XP:
• MSP-FET430UIF
• eZ430-F2013
• eZ430-RF2500
• eZ430-Chronos
The installation procedure for other supported versions of Windows is very similar and, therefore, not
shown here.
Topic
C.1
...........................................................................................................................
Hardware Installation
Page
....................................................................................... 130
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware Installation Guide
© 2009–2010, Texas Instruments Incorporated
129
Hardware Installation
C.1
www.ti.com
Hardware Installation
1. Connect the USB Debug Interface with a USB cable to a USB port of the PC. (eZ430-F2013,
eZ430-RF2500 and eZ430-Chronos can be connected without a cable.)
2. Windows should now recognize the new hardware as an "MSP430 XXX x.xx.xx" (see Figure C-1). The
device name may be different from the one shown here.
Figure C-1. Windows XP Hardware Recognition
3. For CCE v3.1 SR1 and CCSv4.x the drivers will be installed automatically without user interaction
(continue with step 13). For IAR the Hardware Wizard starts automatically and may opens the "Found
New Hardware Wizard" window.
NOTE: This Window may not appear. If it does not, the drivers will be installed automatically.
Continue with step 13.
4. Click "Next". The Hardware Wizard tries to find the driver in the system. If the driver is found, continue
with step 8. If not, press "Back" and continue with step 5.
5. Select "Install from a list or specific location (Advanced)" (see Figure C-2).
Figure C-2. Windows XP Hardware Wizard
130
Hardware Installation Guide
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Hardware Installation
www.ti.com
6. Browse to the folder where the driver information files are located (see Figure C-3).
<br/>
For CCE, the default folder is:
C:\Program Files\Texas Instruments\MSP430_USB_DRIVERS_v3.1\
<br/>
For CCS, the default folder is:
C:\Program Files\Texas Instruments\ccs4\emulation\drivers\msp430\
<br/>
For IAR Embedded Workbench, the default folder is:
C:\Program Files\Texas Instruments\IAR Systems\Embedded Workbench 4.0\
430\drivers\TIUSBFET\WinXP
Figure C-3. Windows XP Driver Location Selection Folder
7. The Wizard generates a message that an appropriate driver has been found.
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware Installation Guide
© 2009–2010, Texas Instruments Incorporated
131
Hardware Installation
www.ti.com
8. Note that Windows may show a warning that the driver is not certified by Microsoft. Ignore this warning
and click "Continue Anyway" (see Figure C-4).
Figure C-4. Windows XP Driver Installation
9. The wizard installs the driver files.
10. The wizard shows a message that it has finished the installation of the software for "MSP-FET430UIF
(TI USB FET) Adapter" (or "MSP430 Application UART").
11. NOTE: This step is for MSP-FET430UIF and eZ430-F2013 only.
After closing the hardware wizard, Windows automatically recognizes another new hardware device
called "MSP-FET430UIF - Serial Port".
12. NOTE: This step is for MSP-FET430UIF and eZ430-F2013 only.
Depending on the current update version of the operating system, corresponding drivers are installed
automatically or the hardware wizard opens again. If the wizard starts again, repeat the previous
steps.
132
Hardware Installation Guide
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Hardware Installation
www.ti.com
13. The USB debug interface is installed and ready to use. The Device Manager lists a new entry as
shown in Figure C-5, Figure C-6, or Figure C-7.
Figure C-5. Device Manager Using MSP-FET430UIF or eZ430-F2013 (CCE and CCS Only)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware Installation Guide
© 2009–2010, Texas Instruments Incorporated
133
Hardware Installation
www.ti.com
Figure C-6. Device Manager Using MSP-FET430UIF or eZ430-F2013 (IAR Only)
134
Hardware Installation Guide
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
Hardware Installation
www.ti.com
Figure C-7. Device Manager Using eZ430-RF2500 (CCE/CCS and IAR)
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
Hardware Installation Guide
© 2009–2010, Texas Instruments Incorporated
135
Document Revision History
www.ti.com
Document Revision History
Version
SLAU278
Changes/Comments
Initial release
SLAU278A
Updated USB driver installation according to CCE v3.1 SR1 and CCS v4.
SLAU278B
Added information about MSP-FET430U80USB, MSP-TS430PN80USB, and eZ430-Chronos.
SLAU278C
Added bills of materials and updated some PCBs in Appendix B.
Added information about MSP-TS430DA38, MSP-TS430DL48, MSP-TS430PW14, MSP-TS430PW28.
SLAU278D
Added information about MSP-TS430L092, MSP-TS430RSB40, MSP-TS430RGC64USB, MSP-TS430PZ100USB,
MSP-FET430F5137RF900
SLAU278E
Added jumper information for MSP-TS430L092 PCBs to Appendix B.
Added new supported devices in Chapter 1.
SLAU278F
Added information about MSP-TS430PW24, MSP-TS430PW28A, MSP-TS430RHA40A, MSP-TS430RGZ48B,
MSP-TS430RGC64B, MSP-TS430PN80A, and MSP-TS430PZ100B.
Updated MSP-TS430RSB40 schematics
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
136
Revision History
SLAU278F – May 2009 – Revised December 2010
Submit Documentation Feedback
© 2009–2010, Texas Instruments Incorporated
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated