IRFM250 2N7225 MECHANICAL DATA Dimensions in mm (inches) 13.59 (0.535) 13.84 (0.545) N–CHANNEL POWER MOSFET 6.32 (0.249) 6.60 (0.260) 1.02 (0.040) 1.27 (0.050) VDSS ID(cont) RDS(on) 30.35 (1.195) 31.40 (1.235) 16.89 (0.665) 17.40 (0.685) 13.59 (0.535) 13.84 (0.545) 20.07 (0.790) 20.32 (0.800) 3.53 (0.139) Dia. 3.78 (0.149) 1 2 200V 27.4A Ω 0.100Ω FEATURES 3 • N–CHANNEL MOSFET • HIGH VOLTAGE • INTEGRAL PROTECTION DIODE 0.89 (0.035) 1.14 (0.045) 3.81 (0.150) BSC 3.81 (0.150) BSC • SIDE TAB & TABLESS PACKAGE OPTIONS AVAILABLE TO–254AA – Isolated Metal Package Pin 1 – Drain Pin 2 – Source • HERMETIC ISOLATED TO-254 PACKAGE • SCREENING OPTIONS AVAILABLE Pin 3 – Gate ABSOLUTE MAXIMUM RATINGS (TC = 25°C unless otherwise stated) VGS ID Gate – Source Voltage Continuous Drain Current IDM PD Pulsed Drain Current Max. Power Dissipation @ TC = 25°C Linear Derating Factor Avalanche Current , Clamped 1 Peak Diode Recovery 2 Thermal Resistance Junction – Case Thermal Resistance Junction – Ambient Thermal Resistance Case – Sink Operating Junction and Storage Temperature Range Lead Temperature (1.6mm from case for 10s) IL dv / dt RθJC RθJA RθCS TJ , TSTG TL 1) 2) @ VGS = 10V , TC = 25°C @ VGS = 10V , TC = 100°C ±20V 27.4A 17A 110A 150W 1.2W / °C 27.4A 5.5V / ns 0.83°C / W 48°C / W 0.21°C / W typ. –55 to 150°C 300°C VDD = 25V , Starting TJ = 25°C , L ≥ 1mH , RG = 25Ω , Peak IL = 27.4A ISD ≤ 27.4A , di/dt ≤ 190A / µS , VDD ≤ BVDSS , TJ ≤ 150°C , Suggested RG = 2.35Ω Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Document Number 3351 Issue 2 IRFM250 2N7225 ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise stated) Parameter BVDSS Test Conditions STATIC ELECTRICAL RATINGS Drain – Source Breakdown Voltage ∆BVDSS Temperature Coefficient of ∆TJ RDS(on) VGS = 0 ID = 1mA Min. Typ. Max. 200 Reference to 25°C V 0.28 V / °C Breakdown Voltage ID = 1mA Static Drain – Source On–State VGS = 10V ID = 17A 0.100 VGS = 10V ID = 27.4A 0.105 VDS = VGS ID = 250µA 2 VDS ≥ 15V IDS = 17A 9 VGS = 0 VDS = 0.8BVDSS 25 TJ = 125°C 250 Resistance 2 VGS(th) Gate Threshold Voltage 2 4 gfs Forward Transconductance IDSS Zero Gate Voltage Drain Current IGSS Forward Gate – Source Leakage VGS = 20V 100 IGSS Reverse Gate – Source Leakage VGS = –20V –100 Ciss DYNAMIC CHARACTERISTICS Input Capacitance Coss Output Capacitance Crss Reverse Transfer Capacitance CDC Drain – Case Capacitance Qg Total Gate Charge VGS = 10V 55 115 Qgs Gate – Source Charge ID = 27.4A 8 22 Qgd Gate – Drain (“Miller”) Charge VDS = 0.5BVDSS 30 60 td(on) Turn– On Delay Time tr Rise Time td(off) Turn–Off Delay Time tf Fall Time IS SOURCE – DRAIN DIODE CHARACTERISTICS Continuous Source Current 700 VDS = 25V f = 1MHz Diode Forward Voltage 2 190 Vgs = 10V 170 trr Reverse Recovery Time 2 27.4 TJ = 25°C VGS = 0 IF = 27.4A 2 nC ns 130 110 IS = 27.4A nA 35 1 VSD µA 12 RG = 2.35Ω Pulse Source Current V (Ω) S(Ω pF 110 VDD = 100V ISM Ω 3500 VGS = 0 ID = 27.4A Unit TJ = 25°C di / dt ≤ 100A/µs VDD ≤ 50V Qrr Reverse Recovery Charge ton Forward Turn–On Time LD PACKAGE CHARACTERISTICS Internal Drain Inductance Measured from 6mm down drain lead to centre of die 8.7 LS Internal Source Inductance 8.7 A 1.9 V 950 ns 9.0 µC Negligible Measured from 6mm down source lead to source bond pad nH 1) Repetitive Rating – Pulse width limited by Maximum Junction Temperature 2) Pulse Test: Pulse Width ≤ 300µs, δ ≤ 2%. Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Document Number 3351 Issue 2 IRFM250 2N7225 PACKAGE OPTIONS TABLESS 13.59 (0.535) 13.84 (0.545) 6.32 (0.249) 6.60 (0.260) 13.59 (0.535) 13.84 (0.545) 1.02 (0.040) 1.27 (0.050) 2 3 13.46 (0.530) 13.97 (0.550) 1 0.89 (0.035) 1.14 (0.045) 3.81 (0.150) BSC 3.81 (0.150) BSC 2 6 .4 2 (1 .0 4 0 ) SIDE TAB 2 0 .0 7 (0 .7 9 0 ) 6 .3 5 (0 .2 5 0 ) 1 2 .7 (0 .5 0 0 ) m in . 1 3 .7 2 (0 .5 4 0 ) 1 3 .7 2 (0 .5 4 0 ) 6 .6 0 (0 .2 6 0 ) 3 .8 1 (0 .1 5 0 ) 1 .0 2 (0 .0 4 0 ) 3 .8 1 (0 .1 5 0 ) 2 p lc s . Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Document Number 3351 Issue 2