MBS SERIES SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIERS Voltage Range - 200 to 1000 Volts Current - 0.5/0.8 Ampere MBS FEATURES Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique High temperature soldering guaranteed: 260*/10 seconds at 5 lbs., (2.3kg) tension Small size, simple installation Leads solderable per MIL-STD-202, Method 208 High surge current capability .193(4.90) .177(4.50) .033(0.84 .022(0.56) .276(7.0) .157(4.00) .142(3.60) MAX + .102(2.60) .087(2.20) .106(2.70) .090(2.30) .008(0.20) .118(3.0) MAX MAX MECHANICAL DATA .014(0.35) .006(0.15) .053(1.53) .037(0.95) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting Position: Any Weight:0.04 ounce, 1.0 grams .083(2.12) .043(1.10) .043(1.10) .028(0.70) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25* ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for capacitive load derate current by 20%. SYMBOLS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TA=30* On glass-epoxy P.C.B. On aluminum substrate Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage drop per leg at 0.4A Maximum DC reverse current TA=25* at rated DC blocking voltage TA=100* Typical junction capactiance per leg(Note3) Typical thermal resistance per leg Operating temperature range storage temperature range VRRM VRMS VDC MB2S MB4S MB6S MB8S MB10S UNITS 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 VOLTS VOLTS VOLTS IF(AV) 0.5 0.8 Amps IFSM 35 Amps VF 1.0 Volts 5.0 100 15 75 -55 to +150 -55 to +150 uA uA IR CJ R* JA TJ TSTG pF */W * * NOTES:1.On glass epoxy P.C.B. mounted on 0.05x0.05''(1.3x1.3mm) pads 2.On aluminum substrate P.C.B. with on area of 0.8''x0.8''(20x20mm) mounted on 0.05X0.05''(1.3X1.3mm) solder pad 3.Measured at 1.0MHz and applied reverse valtage of 4.0 volts. www.shunyegroup.com FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT FOR 0.8 Aluminum Substrate 0.7 0.6 0.5 0.4 Glass Epoxy P.C.B. 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 PEAK FORWARD SURGE CURRENT.(A) AVERAGE FORWARD RECTIFIED CURRENT(A) RATINGS AND CHARACTERISTIC CURVES MBS SERIES FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PERLEG 35 30 Ta=40* Single Half Sine-Wave (JEDEC Method) 25 f=60Hz 20 15 f=50Hz 10 5 0 160 1Cycle 1 10 AMBIENT TEMPERATURE,(*) INSTANTANEOUS REVERSE LEAKAGE CURRENT.(uA) 10 TJ=150* TJ=25* 1 0.01 0.2 0.4 TJ=25* Pulse Width=300*s 1% Duty Cycle 0.6 0.8 1.0 1.2 1.4 1.6 FIG. 4-TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 TJ=125* 10 1 0.1 TJ=25* 0.01 0 20 FIG. 5-TYPICAL JUNCTION CAPACTITANE PER LEG 30 25 TJ=25* f=1.0MHZ Vsig=50mV p-p 20 15 10 5 0 0.1 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE(%) INSTANTANEOUS FORWARD VOLTAGE.(V) JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT(A) FIG. 3-TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 0.1 100 NUMBER OF CYCLES 1 10 100 REVERSE VOLTAGE.(V) www.shunyegroup.com 200