PATENT PENDING PATENT PENDING PATENT PENDING MB2S THRU MB6S MINIATURE GLASS PASSIVATED SINGLE-PHASE SURFACE MOUNT BRIDGE RECTIFIER Reverse Voltage - 200 to 600 Volts Forward Current - 0.5 Ampere TO-269AA FEATURES 0.029 (0.74) 0.017 (0.43) 0.272 (6.90) 0.252 (6.40) 0.161 (4.10) 0.144 (3.65) 0.205 (5.21) 0.195 (4.95) 0.105 (2.67) 0.095 (2.41) 0.049 (1.24) 0.039 (0.99) 0.195 (4.95) 0.179 (4.55) 0-8 0.062 (1.57) 0.058 (1.47) o 0.038 (0.96) 0.019 (0.48) 0.114 (2.90) 0.106 (2.70) 0.094 (2.40) 0.090 (2.30) 0.008 (0.20) 0.004 (0.10) 0.016 (0.41) 0.006 (0.15) 0.117 (2.97) 0.107 (2.72) 0.0075 (0.19) 0.0065 (0.16) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL recognized under Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High surge overload rating: 35A peak ♦ Saves space on printed circuit boards ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 0.018 (0.46) 0.014 (0.36) 0.058 (1.47) 0.054 (1.37) Dimensions in inches and (millimeters) MECHANICAL DATA Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Mounting Position: Any Weight: 0.0078 ounce, 0.22 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Device marking code MB2S MB4S MB6S 2 4 6 UNITS Maximum repetitive peak reverse voltage VRRM 200 400 600 Volts Maximum RMS voltage VRMS 140 280 420 Volts Maximum DC blocking voltage VDC 200 400 600 Volts Maximum average forward output rectified - on glass-epoxy P.C.B. (NOTE 1) current at TA=30°C - on aluminum substrate (NOTE 2) I(AV) 0.5 0.8 Amp Peak forward surge current 8.3msec single half sinewave superimposed on rated load (JEDEC Method) IFSM 35.0 Amps Rating for fusing (t<8.3ms) I2t 5.0 A2sec Maximum instantaneous forward voltage drop per leg at 0.4A VF 1.0 Volts IR 5.0 100 µA CJ 13.0 pF RΘJA RΘJA RΘJL 85.0 70.0 20.0 °C/W TJ, TSTG -55 to +150 °C Maximum DC reverse current at rated DC blocking voltage per leg TA=25°C TA=125°C Typical junction capacitance per leg (NOTE 3) Typical thermal resistance per leg (NOTE 1) (NOTE 2) (NOTE 1) Operating junction and storage temperature range NOTES: (1) On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.3 x 1.3mm) pads (2) On aluminum substrate P.C.B. with an area of 0.8" x 0.8" (20 x 20mm) mounted on 0.05 x 0.05" (1.3 x 1.3mm) solder pad (3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 4/98 RATINGS AND CHARACTERISTIC CURVES MB2S THRU MB6S FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 0.8 0.7 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT GLASS EPOXY P.C.B. 0.6 0.5 0.4 0.3 0.2 0.1 0 RESISTIVE OR INDUCTIVE LOAD 0 20 40 60 35 30 25 f=60 HZ 20 15 1.0 CYCLE 5.0 1 10 AMBIENT TEMPERATURE, °C TJ=150°C 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.4 0.6 0.8 1.0 1.2 1.4 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p 25 20 15 10 5.0 0 0.1 1 10 REVERSE VOLTAGE, VOLTS FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 TJ=125°C 10 1 0.1 TJ=25°C 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS 30 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 0.01 0.2 100 NUMBER OF CYCLES FIG. 3 - TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 0.1 f=50 HZ 10 0 80 100 120 140 160 TA=40°C SINGLE HALF SINE-WAVE (JEDEC Method) 100 200 100