WEIDA CG6257AM

CG6257AM
PRELIMINARY
4Mb (256K x 16) Pseudo Static RAM
Features
when deselected (CE HIGH or both BHE and BLE are HIGH).
The input/output pins (I/O0 through I/O15) are placed in a
high-impedance state when: deselected (CE HIGH ), outputs
are disabled (OE HIGH), both Byte High Enable and Byte Low
Enable are disabled (BHE, BLE HIGH), or during a write
operation (CE LOW and WE LOW). The addresses must not
be toggled once the read is started on the device.
• Wide voltage range: 2.70V–3.30V
• Access Time: 70ns
• Ultra-low active power
— Typical active current: 2.0mA @ f = 1 MHz
•
•
•
•
— Typical active current: 13mA @ f = fmax
Ultra low standby power
Automatic power-down when deselected
CMOS for optimum speed/power
Offered in a 48 Ball BGA Package
Writing to the device is accomplished by taking Chip Enables
(CE LOW ) and Write Enable (WE) input LOW. If Byte Low
Enable (BLE) is LOW, then data from I/O pins (I/O0 through
I/O7), is written into the location specified on the address pins
(A0 through A17). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O8 through I/O15) is written into the location
specified on the address pins (A0 through A17).
Functional Description[1]
The CG6257AM is a high-performance CMOS Pseudo static
RAM organized as 256K words by 16 bits that supports an
asynchronous memory interface. This device features
advanced circuit design to provide ultra-low active current.
This is ideal for providing More Battery Life® (MoBL) in
portable applications such as cellular telephones. The device
can be put into standby mode reducing power consumption by
more than 99% The device can also be put into standby mode
Reading from the device is accomplished by taking Chip
Enables (CE LOW) and Output Enable (OE) LOW while
forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE)
is LOW, then data from the memory location specified by the
address pins will appear on I/O0 to I/O7. If Byte High Enable
(BHE) is LOW, then data from memory will appear on I/O8 to
I/O15. See the truth table at the back of this datasheet for a
complete description of read and write modes
Logic Block Diagram
256K × 16
RAM Array
SENSE AMPS
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
ROW DECODER
DATA IN DRIVERS
I/O0 – I/O7
I/O8 – I/O15
COLUMN DECODER
A11
A12
A13
A14
A15
A16
A17
BHE
WE
CE
OE
BLE
Power- Down
Circuit
BHE
BLE
CE
Note:
1. For best-practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Weida Semiconductor, Inc.
38-XXXXX
Revised August 2003
PRELIMINARY
CG6257AM
Pin Configuration[2, 3, 4]
FBGA
Top View
1
2
3
4
5
6
BLE
OE
A0
A1
A2
NC
A
I/O8
BHE
A3
A4
CE
I/O0
B
I/O9
I/O10
A5
A6
I/O1
I/O2
C
VSS
I/O11
A17
A7
I/O3
Vcc
D
VCC
I/O12 GND
A16
I/O4
Vss
E
I/O14
I/O13
A14
A15
I/O5
I/O6
F
I/O15
NC/
A19
A12
A13
WE
I/O7
G
NC/
A18
A8
A9
A10
A11
NC/
A20
H
Note:
2. DNU pins have to be left floating.
3. Ball H1, G2 and ball H6 for the FBGA package can be used to upgrade to a 8M, 16M and a 32M density respectively.
4. NC “no connect” - not connected internally to the die.
38-XXXXX
Page - 2 - of 12
PRELIMINARY
CG6257AM
Maximum Ratings
DC Voltage Applied to Outputs
in High Z State[5, 6, 7] ........................................–0.4V to 3.3V
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Input Voltage[5, 6, 7].....................................–0.4V to 3.3V
Output Current into Outputs (LOW)............................. 20 mA
Storage Temperature ................................–65°C to + 150°C
Static Discharge Voltage .......................................... >2001V
(per MIL-STD-883, Method 3015)
Ambient Temperature with
Power Applied............................................ –55°C to + 125°C
Latch-Up Current .....................................................>200 mA
Supply Voltage to Ground Potential................. –0.4V to 4.6V
Operating Range[9]
Device
Range
Ambient Temperature
VCC
CG6257AM
Industrial
–25°C to +85°C
2.70V to 3.30V
Product Portfolio
Power Dissipation
Product
Speed
(ns)
VCC Range (V)
Operating ICC(mA)
f = 1MHz
CG6257AM
Min.
Typ.[8]
Max.
2.70
3.0
3.30
70
f = fmax
Standby ISB2(µA)
Typ.[8]
Max.
Typ.[8]
Max.
Typ.[8]
Max.
2
4
13
17
55
80
Notes:
5. VIL(MIN) = -0.5V for pulse durations less than 20ns.
6. VIH(Max) = Vcc + 0.5V for pulse durations less than 20ns.
7. Overshoot and undershoot specifications are characterized and are not 100% tested.
8. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ.), TA = 25°C.
9. Vcc must be at minimal operational levels before inputs are turned ON.
38-XXXXX
Page - 3 - of 12
PRELIMINARY
CG6257AM
Electrical Characteristics Over the Operating Range
CG6257AM-70
Parameter
Description
Test Conditions
Typ.[8]
Min.
VCC
Supplay Voltage
2.7
VOH
Output HIGH Voltage IOH = –1.0 mA
VCC = 2.70V
VOL
Output LOW Voltage IOL = 2.0mA
VCC = 2.70V
VIH
Input HIGH Voltage
VCC= 2.7V to 3.3V
VIL
Input LOW Voltage
VCC= 2.7V to 3.3V(F = 0)
IIX
Input Leakage
Current
IOZ
ICC
Max.
Unit
3.3
V
2.4
V
0.4
V
0.8*Vcc
VCC
+0.3V
V
-0.3
0.4
V
GND < VI < VCC
–1
+1
µA
Output Leakage
Current
GND < VO < VCC, Output Disabled
–1
+1
µA
VCC Operating Supply
Current
f = fMAX = 1/tRC
13
17
mA
2.0
4
mA
350
µA
80
µA
VCC = VCCmax
IOUT = 0 mA
CMOS levels
f = 1 MHz
ISB1
Automatic CE
Power-Down
Current — CMOS
Inputs
Vcc = 3.3V
CE > VCC−0.2V
VIN>VCC–0.2V, VIN<0.2V)
f = fMAX (Address and Data
Only),
f = 0 (OE, WE, BHE and BLE),
VCC=3.30V
ISB2
Automatic CE
Power-Down
Current — CMOS
Inputs
Vcc = 3.3V
CE > VCC – 0.2V
VIN > VCC – 0.2V or VIN < 0.2V,
f = 0, VCC = 3.30V
55
Capacitance[10]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
Max.
Unit
6
pF
8
pF
TA = 25°C, f = 1 MHz,
VCC = VCC(typ)
Thermal Resistance[10]
Description
Thermal Resistance
(Junction to Ambient)
Test Conditions
Still Air, soldered on a 3 × 4.5 inch, two-layer printed
circuit board
Thermal Resistance
(Junction to Case)
Symbol
BGA
Unit
ΘJA
55
°C/W
ΘJC
16
°C/W
Note:
10. Tested initially and after any design or process changes that may affect these parameters.
38-XXXXX
Page - 4 - of 12
PRELIMINARY
CG6257AM
AC Test Loads and Waveforms
R1
VCC
OUTPUT
50 pF
INCLUDING
JIG AND
SCOPE
38-XXXXX
VCC
R2
10%
GND
Rise Time = 1 V/ns
ALL INPUT PULSES
90%
90%
10%
Fall Time = 1 V/ns
Equivalentto:
THÉVENINEQUIVALENT
RTH
OUTPUT
V
Parameters
3.0V VCC
Unit
R1
1179
Ω
R2
1941
Ω
RTH
733
Ω
VTH
1.87
V
Page - 5 - of 12
PRELIMINARY
CG6257AM
Switching Characteristics Over the Operating Range[11]
70 ns
Parameter
Description
Min.
Max.
Unit
READ CYCLE
tRC
Read Cycle Time
70
tAA
Address to Data Valid
tOHA
Data Hold from Address Change
tACE
CE LOW to Data Valid
70
ns
tDOE
OE LOW to Data Valid
35
ns
OE LOW to LOW Z
tHZOE
OE HIGH to High Z[12, 14]
tLZCE
CE LOW to Low Z
70
[12, 14]
tLZOE
[12, 14]
tDBE
BLE / BHE LOW to Data Valid
tLZBE
BLE / BHE LOW to Low Z[12, 14]
BLE / BHE HIGH to HIGH
ns
5
Z[12, 14]
Address Skew
ns
ns
25
ns
70
ns
5
Z[12, 14]
ns
ns
25
CE HIGH to High
tSK
10
5
tHZCE
tHZBE
ns
ns
25
ns
0
ns
[13]
WRITE CYCLE
tWC
Write Cycle Time
70
ns
tSCE
CE LOW to Write End
60
ns
tAW
Address Set-Up to Write End
60
ns
tHA
Address Hold from Write End
0
ns
tSA
Address Set-Up to Write Start
0
ns
tPWE
WE Pulse Width
45
ns
tBW
BLE / BHE LOW to Write End
60
ns
tSD
Data Set-Up to Write End
45
ns
tHD
Data Hold from Write End
0
ns
tHZWE
tLZWE
WE LOW to
High-Z[12, 14]
WE HIGH to
Low-Z[12, 14]
25
5
ns
ns
Notes:
11. Test conditions for all parameters other than tri-state parameters assume signal transition time of 1ns/V, timing reference levels of VCC(typ)/2, input pulse
levels of 0V to VCC(typ.), and output loading of the specified IOL/IOH as shown in the “AC Test Loads and Waveforms” section..
12. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high impedence state.
13. The internal Write time of the memory is defined by the overlap of WE, CE = VIL, BHE and/or BLE = VIL. All signals must be ACTIVE to initiate a write and
any of these signals can terminate a write by going INACTIVE. The data input set-up and hold timing should be referenced to the edge of the signal that
terminates the write
14. High-Z and Low-Z parameters are characterized and are not 100% tested. .
38-XXXXX
Page - 6 - of 12
PRELIMINARY
CG6257AM
Switching Waveforms
Read Cycle 1 (Address Transition Controlled)[15, 16]
tRC
ADDRESS
tSK
DATA OUT
tOHA
tAA
DATA VALID
PREVIOUS DATA VALID
Read Cycle 2 (OE Controlled) [15, 16]
ADDRESS
CE
tRC
tSK
tPD
tHZCE
tACE
BHE/BLE
tLZBE
tDBE
tHZBE
OE
tHZOE
tDOE
DATA OUT
VCC
SUPPLY
CURRENT
tLZOE
HIGH IMPEDANCE
tPU
HIGH
IMPEDANCE
DATA VALID
tLZCE
50%
50%
ICC
ISB
Note:
15. WE is HIGH for Read Cycle.
16. Addresses should not be toggled after the start of a read cycle
38-XXXXX
Page - 7 - of 12
PRELIMINARY
CG6257AM
Switching Waveforms (continued)
Write Cycle 1 (WE Controlled) [13, 14, 17, 18, 19]
t WC
ADDRESS
tSCE
CE
tAW
tSA
tHA
tPWE
WE
tBW
BHE/BLE
OE
tSD
DATAI/O
tHD
VALID DATA
DON’T CARE
tHZOE
[13, 14, 17, 18, 19]
Write Cycle 2 (CE Controlled)
t WC
ADDRESS
tSCE
CE
tSA
tAW
tHA
tPWE
WE
tBW
BHE/BLE
OE
tSD
DATAI/O
tHD
VALID DATA
DON’T CARE
tHZOE
Notes:
17. Data I/O is high impedance if OE = VIH.
18. If Chip Enable goes INACTIVE with WE = VIH, the output remains in a high-impedance state.
19. During the DON’T CARE period in the DATA I/O waveform, the I/Os are in output state and input signals should not be applied.
38-XXXXX
Page - 8 - of 12
PRELIMINARY
CG6257AM
Switching Waveforms (continued)
[18, 19]
Write Cycle 3 (WE Controlled, OE LOW)
tWC
ADDRESS
tSCE
CE
tBW
BHE/BLE
tAW
tSA
tHA
tPWE
WE
tHD
tSD
DATAI/O
DON’T CARE
VALID DATA
tLZWE
tHZWE
Write Cycle 4 (BHE/BLE Controlled, OE LOW)
[18, 19]
tWC
ADDRESS
CE
tSCE
tAW
tHA
tBW
BHE/BLE
tSA
WE
tPWE
tSD
DATA I/O
38-XXXXX
DON’T CARE
tHD
VALID DATA
Page - 9 - of 12
PRELIMINARY
CG6257AM
Truth Table[20]
CE
WE
OE
BHE
BLE
H
X
X
X
X
X
X
X
H
L
H
L
L
L
H
L
L
H
L
L
H
L
H
L
Inputs/Outputs
Mode
Power
High Z
Deselect/Power-Down
Standby (ISB)
H
High Z
Deselect/Power-Down
Standby (ISB)
L
Data Out (I/O0 – I/O15)
Read
Active (ICC)
H
L
Data Out (I/O0 – I/O7);
High Z (I/O8 – I/O15)
Read
Active (ICC)
L
H
High Z (I/O0 – I/O7);
Data Out (I/O8 – I/O15)
Read
Active (ICC)
H
L
H
High Z
Output Disabled
Active (ICC)
H
H
L
High Z
Output Disabled
Active (ICC)
H
H
L
L
High Z
Output Disabled
Active (ICC)
L
L
X
L
L
Data In (I/O0 – I/O15)
Write
Active (ICC)
L
L
X
H
L
Data In (I/O0 – I/O7);
High Z (I/O8 – I/O15)
Write
Active (ICC)
L
L
X
L
H
High Z (I/O0 – I/O7);
Data In (I/O8 – I/O15)
Write
Active (ICC)
Note:
20. H = VIH, L = VIL, X = Don’t Care
Ordering Information
Speed
(ns)
Ordering Code
Package
Name
Package Type
Operating
Range
70
CG6257AM
BA48K
48-ball Fine Pitch BGA (6 mm × 8mm × 1.2 mm)
Industrial
38-XXXXX
Page - 10 - of 12
PRELIMINARY
CG6257AM
Package
48-Ball (6 mm x 8mm x 1.2 mm) FBGA BA48K
BOTTOM VIEW
TOP VIEW
A1 CORNER
Ø0.05 M C
Ø0.25 M C A B
Ø0.30±0.05(48X)
A1 CORNER
1
2
3
4
5
6
6
4
3
2
C
F
D
E
F
2.625
8.00±0.10
E
0.75
B
C
5.25
A
B
G
G
H
H
A
1.875
A
0.75
6.00±0.10
B
3.75
B
0.15 C
0.21±0.05
0.53±0.05
0.25 C
1
A
D
8.00±0.10
5
6.00±0.10
0.15(4X)
REFERENCE JEDEC MO-207
C
1.20 MAX
0.36
SEATING PLANE
51-85193-*A
MoBL and More Battery Life are trademarks of Cypress Semiconductor Corporation. All product and company names mentioned
in this document may be the trademarks of their respective holders
38-XXXXX
Page - 11 - of 12
© Weida Semiconductor, Inc., 2002. The information contained herein is subject to change without notice. Weida Semiconductor assumes no responsibility for the use of any circuitry other than
circuitry embodied in a Weida Semiconductor product. Nor does it convey or imply any license under patent or other rights. Weida Semiconductor does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Weida Semiconductor products
in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Weida Semiconductor against all charges.
PRELIMINARY
CG6257AM
Document Title: CG6257AM MoBL3® 4Mb (256K x 16) Pseudo Static RAM
Document Number: 38-XXXXX
REV.
**
38-XXXXX
ECN NO.
Issue
Date
Orig. of
Change
10/21/03
MPR
Description of Change
New Datasheet
Page - 12 - of 12