P-511-508(V:4) PD057VU7 FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com By Confirmed By Prepared By The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:1 P-511-508(V:4) PD057VU7 Revision History Rev. Issued Date 1.0 May 15, 2008 Eng. ࣑ܦᙤ 2.0 May 19, 2009 ࣑ܦᙤ 3.0 Jun. 19, 2009 ࣑ܦᙤ 4.0 Jul. 3, 2009 ࣑ܦᙤ Revised Contents New Delete backlight connector pin pitch BeforeΚ Connector typeΚJST BHR-03VS-1, PIN No 2 pins, pitch=3.5mm AfterΚ Connector typeΚJST BHR-03VS-1, PIN No 3 pins Icc Max. from 100mA to 75mA LCD Panel Power ConsumptiooǺ Max. from 0.33W to 0.25W Total Power ConsumptionǺ Max. from 2.97W to 2.89W The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:2 P-511-508(V:4) PD057VU7 TECHNICAL SPECIFICATION CONTENTS NO. ITEM PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Cover Contents Revision History Application Features Mechanical Specifications Mechanical Drawing of TFT-LCD module Input / Output Terminals Touch Panel Characteristics Absolute Maximum Ratings Electrical Characteristics Pixel Arrangement Display Color and Gray Scale Reference Interface Timing Power On Sequence Optical Characteristics 1 2 3 4 4 4 5 6 7 9 9 10 11 12 15 15 18 19 20 Handling Cautions Reliability Test Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:3 P-511-508(V:4) PD057VU7 1. Application This data sheet applies to a color TFT LCD module, PD057VU7. PD057VU7 module applies to OA product, car TV (must use Analog to Digital driving board), which requires high quality flat panel display. If you must use in severe reliability environment, please don’t extend over PVI’s reliability test conditions. 2. Features . QVGA (320*240 pixels) resolution . Module with resistive type touch panel . Amorphous silicon TFT LCD panel with LED . Pixel in stripe configuration . Thin and light weight . Display ColorsΚ262,144 colors . TTL interface 3. Mechanical Specifications Parameter Screen Size Display Format Display Colors Active Area Pixel Pitch Pixel Configuration Outline Dimension Weight Back-light Surface treatment Display mode Surface treatment of Touch Panel Gray scale inversion direction Specifications 5.7 (diagonal) 320ͪ(R,G,B)ͪ240 262,144 115.20 (H)ͪ86.4 (V) 0.36(H)ͪ0.36(V) Stripe 144(W)Ø104.6 (H)Ø14.45 (D) (typ.) 244²10 36-LED Anti-glare + SWV Normally white 3H 6 o`clock [ ref. to Note 13-1 ] Unit inch dot mm mm mm g The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:4 P-511-508(V:4) PD057VU7 4.Mechanical Drawing of TFT-LCD Module Outline Drawing : Front View (unit : mm) E307459 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:5 P-511-508(V:4) PD057VU7 5.Input / Output Terminals 5-1) TFT-LCD Panel Driving Connector type: ELCO 08-6210-033-340-800A+, PIN No 33 pins Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Symbol I/O GND I CK I Hsync I Vsync GND R0 I R1 I R2 I R3 I R4 I R5 GND I G0 I G1 I G2 I G3 I G4 I G5 GND I B0 I B1 I B2 I B3 I B4 I B5 GND I ENAB VCC VCC 30 R/L I 31 U/D I 32 33 V/Q GND I - Description GND Clock signal for sampling each data signal Horizontal synchronous signal(neqative) Vertical synchronous signal(neqative) GND RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GND GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) GND Blue data signal(LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal(MSB) GND Signal to settle the horizontal display position(positive) +3.3V power supply +3.3V power supply Horizontal display mode select signal LΚNormal ,HΚLeft /Right reverse mode Vertical display mode select signal HΚNormal ,L :Up/Down reverse mode VGA / QVGA mode select signal GND Remark Note5-1 Note5-2 Note5-3 Note11-2 Note5-1ΚThe horizontal display start timing is settled in accordance with rising of ENAB signal. In case ENAB is fixed ”Low”,the horizontal start timing is determined as described in 10-2. Don`t keep ENAB”High” during operation. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:6 P-511-508(V:4) PD057VU7 Note 5-2 , 5-3ǺThe definitions of U/D & R/L R/L(PIN 30)= Low, U/D(PIN 31)= High R/L(PIN 30)= High , U/D(PIN 31)= Low 5-2) LED Backlight driving Connector type: JST BHR-03VS-1, PIN No 3 pins Pin No Symbol 1 + 2 NC 3 - Description Remark Input terminal (Anode) Red No connect - Input terminal (Cathode) Black 6.Touch Panel Characteristics 6-1) Pin assignmentΚ Κ Pin No. Designation 1 YU (Bottom) 2 XL (Top) 3 YL (Botton) 4 XR (Top) Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:7 P-511-508(V:4) PD057VU7 Κ 6-2) Electrical PerformanceΚ Parameters Terminal Resistance Input Voltage Linearity (X ,Y direction) Insulation Impedance Response Time Operation Force Symbol X Y VT MIN. 400 230 20 - Typ. 550 320 5 - MAX. 810 540 7 ±1.5 15 50 Unit Ω Ω V % MΩ ms g Remark DC 25V Note 6-1 Note 6-1 Input through R0.8mm stylus or R8.0mm finger. 6-3) Durability Performance 1. Hitting Durability: At least 1,000,000 times with R8.0mm silicon rubber, 250g, 3 times/sec. 2. Sliding Durability: At least 1,00,000 times with R0.8mm polyacetal stylus, 250g, 60 mm/sec. 6-4) Integration Design Guide Avoid the design that Front-case overlap and press on the active area of the touch-panel. Give enough gap (over 0.5mm at compressed) between the front case and touch-panel to protect wrong operating. Use a buffer material (Gasket) between the touch-panel and front-case to protect damage and wrong operating. Avoid the design that buffer material overlap and press on the inside of touch-panel viewing area. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:8 P-511-508(V:4) PD057VU7 Note 6-2 We strongly suggest to follow above design guide to avoid the linear defect happened on the touch panel. 7.Absolute Maximum Ratings: Parameters Input Voltage GND=0V, Ta=25к Symbol VI Condition MAX. Unit V Ta=25к -0.3~+4 Ta=25к +3.3V supply voltage VCC 0~+3.6 V Note7-1:CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,R/L,U/D,V/Q Remark Note7-1 8.Electrical Characteristics 8-1) Recommended Operating Conditions: Item +3.3V Supply Voltage Permissive input ripple voltage Input voltage(Low) Input voltage(High) GND=0V, Ta=25к Symbol VCC Min. Typ. Max. +3.0 +3.3 +3.6 VRF VIL VIH 0 0.7 VCC - Unit V Remark 100 mVp-p VCC=3.3V 0.3 VCC V V VCC The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:9 P-511-508(V:4) PD057VU7 8-2) Recommended Driving Condition for LED Back Light Parameter LED voltage LED current Symbol VLED ILED Min. - Typ. 20 Max. (11) - Unit V mA Back Light Power Consumption PLED - - 2640 mW Ta=25к Remark Note 8-1 Note 8-2 Note 8-1 Note 8-3 Note 8-1ΚThe ILED = 20 mA (Constant current) Note 8-2ΚThe LED driving condition is defined for each LED module. (3 LED Serial) The input current= 20 mA*12=240 mA. Note 8-3ΚPLED = VLED-1 * ILED-1 + VLED-2* ILED-2 ….. + VLED-11 * ILED-11+VLED-12 * ILED-12 Anode 8-3) Power Consumption Parameters +3.3V Current Dissipation LCD Panel Power Consumption Total Power Consumption Cathode Symbol ICC - Typ. 67 0.22 Max. 75 0.25 Unit mA W - - 2.89 W Remark Note 8-4 Note 8-4ΚThe power consumption for back light is not included. 9. Pixel Arrangement The LCD module pixel arrangement is stripe configuration. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:10 P-511-508(V:4) PD057VU7 10. Display Color and Gray Scale Reference Color Input Color Data Green Red Blue R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Basic Colors Red Green Blue Black Red (63) Green (63) Blue (63) Cyan Magenta Yellow White Red (00) Red (01) Red (02) Darker ʆ Brighter Red (61) Red (62) Red (63) Green (00) Green (01) Green (02) Darker ʆ Brighter Green (61) Green (62) Green (63) Blue (00) Blue (01) Blue (02) Darker ʆ Brighter Blue (61) Blue (62) Blue (63) 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ ʆ 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:11 P-511-508(V:4) PD057VU7 11. Interface Timing 11-1) Timing Parameters AC Electrical Characteristics (VCC =+3.3V,GND=0V,Ta=25к) Characteristics Clock Symbol Frequency 1/Tc Min. 40 5 10 30.0 700 50.0 360 2 515 251 2 Typ. 25.18 Max. 28.33 Unit MHz 6.3 7.0 MHz Duty ratio Tch/Tc 50 60 % Set up time Tds Data ns Hold time Tdh 31.8 us TH 800 900 clock Horizontal Cycle 63.6 us sync. signal TH 400 450 clock Pulse width THp 96 200 clock Vertical sync. TV 525 560 Cycle line signal TV 262 280 Pulse width TVp 34 line Horizontal display period THd 320 Clock Hsync.-Clock phase difference THc 10 Tc-10 ns Hsync.-Vsync. phase difference TVh 0 TH-THp ns Vertical sync. signal start 34 TVs line position 7 Note11-1ΚIn case of lower frequency, the deterioration of the display quality, may occur. Remark V/Q=H V/Q=L V/Q=L V/Q=H V/Q=L V/Q=H V/Q=L V/Q=H V/Q=L flicker etc., Parameter symbol Min. Typ Max Unit Remark Enable Set up time Tes 5 Tc-10 ns signal Pulse width Tep 2 320 TH-10 clock 44 TH-664 V/Q=H Hsync-Enable signal The clock phase difference 2 TH-340 V/Q=L Note11-2Κ When ENAB is fixed at “V/Q=Low”, the display starts from the data of C52 (clock). When ENAB is fixed at “V/Q=High”, the display starts from the data of C104 (clock). The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:12 (ENAB) Enable signal Data B0~B5) (R0~R5,G0~G5, Data signal (CK) Clock signal (Hsync) Signal Horizontal sync. 0.3VDD THc 0.7VDD Д D1 Tcl 0.3VDD 0.7VDD Tep THd 0.7VDD D2 Tds Tdh 0.3VDD 0.7VDD *1 CN 0.7VDD Tes 0.3VDD Tch Tc TH D320 0.3VDD 0.3VDD Horizontal invalid data period Number of H-data *1 When ENAB is fixed at V/Q=”H”, the display starts from the data of C104 (Clock). When ENAB is fixed at V/Q=”L”, the display starts from the data of C52 (Clock). The C1 0.3VDD Horizontal invalid data period 0.3VDD 0.3VDD 0.7VDD THp P-511-508(V:4) PD057VU7 11-2) Timing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:13 B0~B5) signal(R0~R5,G0~G5, Data sync.Signal(Hsync) Horizontal sync.Signal(Vsync) Vertical TVh 0.3VDD 1line 2line TVs 0.7VDD *2 Nline*2 DH1 DH2 TVd The vertical display position (TVs) is fixed at 34th line (V/Q=H) and 7th line (V/Q=L). Verticla invalid data period 0.7VDD TVp TV DH240 Verticla invalid data period 0.3VDD P-511-508(V:4) PD057VU7 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:14 P-511-508(V:4) PD057VU7 12. Power On Sequence VDD 3.0V 3.0V Signal*3 0.3V t2 t1 t3 Back Light ON OFF OFF 10ms 10ms 1. 0Іt1Љ20ms 2. 0Іt2Љ50ms 3. 0Іt3Љ1s 13. Optical Characteristics 13-1) Specification: Parameter Symbol Ӱ Horizontal Viewing Angle Vertical Contrast Ratio Response time Ӱ(to 6 o’clock) Ӱ(to 12 o’clock) CR Rise Tr Fall Tf Condition CRЊ10 At optimized viewing angle Ӱ=0̓ Ӱ=0°/ӽ=0 MIN. TYP. MAX. 55 60 - Ta=25к Unit Remarks deg Note 13-1 45 50 - deg 35 40 - deg 300 600 - - - 15 30 ms - 25 ms 500 600 50 - Brightness - Luminance Uniformity U% 80 85 - % x 0.27 0.31 0.35 - 0.30 0.34 20000 - 0.38 - hrs White Chromaticity LED Life Time y - Note 13-2 Note 13-3 cd/ф Note 13-5 Note 13-6 Note 13-4 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:15 P-511-508(V:4) PD057VU7 Note 13-1ΚThe definitions of viewing angles are as follow LED Note 13-2ΚThe definition of contrast ratio CR = Luminance at White Pattern Luminance at Black Pattern Note 13-3ΚDefinition of Response Time Tr and Tf W hite Black W hite 100% 90% Brightness 10% 0% Tr Tf Note 13-4ΚThe “LED Life time “ is defined as the module brightness decrease to 50% original Brightness that the ambient temperature is 25к and ILED = 240mA. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:16 P-511-508(V:4) PD057VU7 Note 13-5ΚAll optical measurements shall be performed after backlight being turned-on for 30 mins. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure. Photometer (TOPCON BM-5A or BM-7 fast) 500 mm +/- 50 mm Field = 1° TFT-LCD module Optical characteristics measuring configuration Note 13-6ΚThe uniformity of LCD is defined as U= The Minimum Brightness of the 9 testing Points The Maximum Brightness of the 9 testing Points Luminance meter: BM-5A or BM-7 fast (TOPCON) Measurement distance: 500 mm +/- 50 mm Ambient illumination: < 1 Lux Measuring direction: Perpendicular to the surface of module The test pattern is white. 1/6 2/6 2/6 1/6 1/6 2/6 2/6 1/6 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:17 P-511-508(V:4) PD057VU7 14. Handling Cautions 14-1) Mounting of module a) Please power off the module when you connect the input/output connector. b) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. c) Protective film (Laminator) is applied on surface to protect it against scratches and dirts. d) Please following the tear off direction as figure 14-1 to remove the protective film as slowly as possible, so that electrostatic charge can be minimized. 14-2) Precautions in mounting a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 14-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 14-4) Others a) Don`t expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. f) Please adjust the voltage of common electrode as material of attachment by 1 module. 14-5) Polarizer mark The polarizer mark is to describe the direction of wide view angle film how to match up with the rubbing direction. Figure 14-1 the way to peel off protective film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:18 P-511-508(V:4) PD057VU7 15. Reliability Test No Test Item Test Condition 1 High Temperature Storage Test Ta = +85к, 240 hrs 2 Low Temperature Storage Test Ta = -40к, 240 hrs 3 High Temperature Operation Test Ta = +80к, 240 hrs 4 Low Temperature Operation Test Ta = -30к, 240 hrs 5 6 Remark High Temperature & High Humidity Ta = +60к, 90%RH, 240 hrs Operation Test (No Condensation) Thermal Cycling Test -20к+70к, 200 Cycles (non-operating) 30 min Vibration Test 7 (non-operating) Shock Test 8 (non-operating) 30 min Frequency: 10 ~ 57 HZ /Vibration Width:0.075 mm 58-500 Hz / Gravity: 9.8m/s2 Sweep time: 11 minutes Test period: 3 hrs for each direction of X, Y, Z Gravity: 490m/s2 * 6ms Direction: ̈́X, ̈́Y, ̈́Z 3 times for each direction Electrostatic Discharge Test 9 (non-operating) Machine Mode = ̈́200V C = 200pF , R = 0Ө 1 times discharge for each pad Hitting Durability Test (Touch panel) Sliding Durability Test 11 (Touch panel) 1,000,000 times, with R 8.0 mm silicon rubber, 250g, 3times/sec 1,00,000 times, with R 0.8 mm polyacetal stylus, 250g, 60mm/sec 10 Ta: ambient temperature Note: The protective film must be removed before temperature test [Criteria] In the standard conditions, there is not display function NG issue occurred. (IncludingΚline defect, no image) All the cosmetic specification is judged before the reliability stress. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:19 P-511-508(V:4) PD057VU7 16. Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:20