PLA192 Single Pole OptoMOS® Relays Load Voltage Load Current Max RON PLA192 600 150 22 Description The PLA192 is a 1-Form-A solid state relay that uses optically coupled relay technology to provide an enhanced 5000V isolation barrier between the input and output of the relay. The efficient MOSFET switches use Clares patented OptoMOS® architecture. The optically coupled input is controlled by a highly efficient GaAIAs infrared LED. Units V mA Ω Features • 5000VRMS Input/Output Isolation • Small 6 Pin DIP Package • Low Drive Power Requirements (TTL/CMOS Compatible) • No Moving Parts • High Reliability • Arc-Free With No Snubbing Circuits • No EMI/RFI Generation • Machine Insertable, Wave Solderable • 600 volt blocking Approvals • UL Approved to UL1577 • CSA Certified • Complies with EN60950 Ordering Information Applications • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment—Patient/Equipment Isolation • Security • Aerospace • Industrial Controls Part # PLA192 PLA192S Description 6 Pin Dip (50/Tube) 6 Pin Surface Mount (50/Tube) PLA192STR 6 Pin Surface Mount (1000/Reel) Pin Configuration PLA192 Pinout AC/DC Configuration + Control Ð Control Do Not Use 1 6 2 5 3 4 Load Do Not Use Load PLA192 Pinout DC Only Configuration + Control Ð Control Do Not Use 1 6 2 5 3 4 + Load Ð Load Switching Characteristics of Normally Open (Form A) Devices 10ms CONTROL + 90% LOAD 10%+ 10%+ TON DS-PLA192-R2.0 www.clare.com TOFF 1 PLA192 Absolute Maximum Ratings (@ 25˚ C) Parameter Min Input Power Dissipation Input Control Current Peak (10ms) Reverse Input Voltage Total Power Dissipation Peak Blocking Voltage Isolation Voltage Input to Output (60 seconds) 5000 Operational Temperature -40 Storage Temperature -40 Soldering Temperature DIP Package Surface Mount Package (10 Seconds Max.) 1 Derate Linearly 1.33 mw/˚C 2 Derate Linearly 6.67 mw/˚C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Typ Max Units - 1501 50 1 5 8002 600 - VRMS +85 °C +125 °C - +260 +220 mW mA A V mW V °C °C Electrical Characteristics Parameter Conditions Output Characteristics @ 25°C Load Current (Continuous) AC/DC Configuration DC Configuration Peak Load Current 10ms On-Resistance* AC/DC Configuration IL=150mA DC Configuration IL=220mA Off-State Leakage Current VL=600V Switching Speeds Turn-On IF=5mA, VL=10V Turn-Off IF =5mA, VL=10V Output Capacitance 50V; f=1MHz Input Characteristics @ 25°C Input Control Current IL=100mA Input Dropout Current Input Voltage Drop IF=5mA Reverse Input Voltage Reverse Input Current VR=5V Common Characteristics @ 25°C Input to Output Capacitance * 2 Symbol Min Typ Max Units IL IL - - 150 220 350 mA mA mA ILEAK - - 22 8 1 Ω Ω µA TON TOFF COUT - 50 5 5 - ms ms pF IF IF VF VR IR 5 0.4 0.9 - 0.7 1.2 - 50 1.4 5 10 mA mA V V µA CI/O - 3 - pF ILPK RON Within 1 second of on time www.clare.com Rev. 2.0 PLA192 PERFORMANCE DATA* PLA192 Typical On-Resistance Distribution (N=50 Ambient Temperature = 25°C) (Load Current = 150mADC; IF = 5mADC) PLA192 Typical LED Forward Voltage Drop (N=50 Ambient Temperature = 25°C) IF = 5mADC 35 PLA192 Typical Blocking Voltage Distribution (N=50 Ambient Temperature = 25°C) 30 25 25 20 15 10 25 20 Device Count (N) Device Count (N) Device Count (N) 30 15 10 5 1.26 1.27 1.28 18 1.29 18.25 18.5 18.75 19 700 19.25 710 PLA192 Typical IF for Switch Operation (N=50 Ambient Temperature = 25°C) (Load Current = 150mADC) 20 15 10 10 5 0 0 750 30 15 5 740 35 Device Count (N) 20 Device Count (N) 25 730 PLA192 Typical Turn-On Time (N=50 Ambient Temperature = 25°C) (Load Current = 100mADC; IF = 5mADC) PLA192 Typical IF for Switch Dropout (N=50 Ambient Temperature = 25°C) 25 720 Blocking Voltage (V) On-Resistance (Ω) LED Forward Voltage Drop (V) Device Count (N) 10 0 0 1.25 15 5 5 0 20 25 20 15 10 5 1.05 1.35 1.65 1.95 0 0.75 2.25 1.05 LED Current (mA) 35 30 220 25 20 15 10 5 0 0.29 0.32 0.35 160 10mA 5mA AC/DC Configuration 140 10mA 5mA -40 -20 0 40 60 80 100 120 20 10 0.04 0.03 0.02 0.01 20 40 60 Temperature (°C) 80 100 120 0 -40 -20 0 20 40 60 Temperature (°C) 2.0 2.1 18 16 14 12 10 8 6 4 2 0 -40 IF=5mA IF=10mA -20 0 20 40 60 80 100 PLA192 Typical Blocking Voltage vs. Temperature Blocking Voltage (VRMS) IF=5mA 30 1.9 Temperature (°C) PLA192 Typical Leakage vs. Temperature (Measured across Pins 4 & 6) Leakage (µA) On-Resistance (Ω) 20 0.05 0 1.8 PLA192 Typical On-Resistance vs. Temperature (Load Current = Max Rated at Temp.) DC Configuration 0.06 40 1.7 Temperature (°C) PLA192 Typical On Resistance vs. Temp. Load Current=100mA Instantaneous -40 -20 1.6 Turn-On (ms) 180 0.38 50 0 2.25 DC Configuration Turn-Off (ms) 60 1.95 200 120 0.26 1.65 PLA192 Maximum Load Current vs. Temperature 240 Load Current (mA) Device Count (N) PLA192 Typical Turn-Off Time (N=50 Ambient Temperature = 25°C) (Load Current = 100mADC; IF = 5mADC) 0.23 1.35 LED Current (mA) On-Resistance (Ω) 0.75 80 100 770 760 750 740 730 720 710 700 -40 -20 0 20 40 60 80 100 Temperature (°C) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. Rev. 2.0 www.clare.com 3 PLA192 PERFORMANCE DATA* 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -40 -20 PLA192 Typical Turn-Off vs. Temperature (Load Current = 100mADC) LED Forward Voltage Drop (V) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 20 40 60 0 80 100 120 -40 -20 0 PLA192 Typical Turn-On vs. LED Forward Current (Load Current = 150mADC) 40 60 80 100 3.0 1.0 2.7 0.8 1.5 1.2 0.9 0.6 0.5 0.4 0.3 0.6 0.2 0.3 0.1 0 0 10 15 20 25 30 35 1.2 5mA 1.0 0.8 40 45 50 0 Forward Current (mA) -20 0 20 1.0 Load Current (A) 1.2 100 0 -50 -100 10 15 20 25 40 60 80 100 120 30 35 40 PLA192 Typical IF for Switch Operation vs. Temperature (Load Current = 100mADC) 2.500 2.000 1.500 1.000 0.500 0 -40 -20 0 20 40 60 80 100 Temperature (°C) PLA192 Energy Rating Curve 150 50 5 Forward Current (mA) PLA192 Typical Load Current vs. Load Voltage (Ambient Temperature = 25°C) IF = 5mADC 3.000 LED Current (mA) Turn-On (ms) 1.8 5 1.4 Temperature (°C) 0.7 2.1 0 1.6 -40 PLA192 Typical Turn-Off vs. LED Forward Current (Load Current = 150mADC) 2.4 Turn-On (ms) 20 1.8 Temperature (°C) Temperature (°C) Load Current (mA) PLA192 Typical LED Forward Voltage Dropout vs. Temperature 1.0 IF =5mA Turn-Off (ms) Turn-On (ms) PLA192 Typical Turn-On vs. Temperature (Load Current = 100mADC) 0.8 0.6 0.4 0.2 -150 -2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 Load Voltage (V) 0 10µs 100µs 1ms 10ms 100ms 1s 10s 100s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com Rev. 2.0 MECHANICAL DIMENSIONS 6Pin DIP Through Hole (Standard) 8.382 – 0.381 (0.330 – 0.015) 7.620 – 0.254 (0.300 – 0.010) 3.302 – 0.051 (0.130 – 0.002) PC Board Pattern (Top View) 7.239 TYP (0.285 TYP) 2.540 ± 0.127 6-0.800 DIA. (0.100 ± 0.005) (6-0.031 DIA.) 6.350 – 0.127 (0.250 – 0.005) 7.620 ± 0.127 6.350 ± 0.127 (0.300 ± 0.005) (0.250 ± 0.005) 0.254 TYP (0.010 TYP) 2.54 – 0.127 (0.100 – 0.005) 9.144 – 0.508 (0.360 – 0.020) 5.080 ± 0.127 (0.200 ± 0.005) 6Pin DIP Surface Mount (“S” Suffix) 7.620 – 0.254 (0.300 – 0.010) 3.302 – 0.051 (0.130 – 0.002) PC Board Pattern (Top View) 2.540 ± 0.127 8.382 – 0.381 (0.330 – 0.015) 9.525 – 0.254 (0.375 – 0.010) 4.445 – 0.127 (0.175 – 0.005) 0.254 – 0.0127 (0.010 – 0.0005) (0.100 ± 0.005) 2.54 – 0.127 (0.100 – 0.005) 6.35 – 0.127 (0.250 – 0.005) 0.635 – 0.127 (0.025 – 0.005) 8.305 ± 0.127 (0.327 ± 0.005) 1.905 ± 0.127 (0.075 ± 0.005) 1.499 ± 0.127 (0.059 ± 0.005) 0.457 – 0.076 (0.018 – 0.003) 8.382 ± 0.381 (0.330 ± 0.015) Tape and Reel Packaging for 6 Pin Power DIP Surface Mount Package 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) W = 16.30 MAX (0.642 MAX) B0 = 10.30 (0.406) Top Cover Tape Embossment Carrier Embossment K1 = 3.80 (0.150) P = 12.00 (0.472) K0 = 4.90 (0.193) User Direction of Feed A0 = 10.30 (0.406) Dimensions mm (inches) For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-PLA192-R2.0 ©Copyright 2003, Clare, Inc. OptoMOS® is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 1/29/03