LAA125L Single Pole OptoMOS® Relays Load Voltage Load Current Max RON LAA125L 350 150 18 Description LAA125L is a 350V, 150mA, 18Ω 2-Form-A relay. It combines enhanced peak load current capability with low on-resistance. Current limiting version is available (“L” suffix, see specification for variations in performance). Units V mA Ω Features • Small 8 Pin DIP Package • Low Drive Power Requirements (TTL/CMOS Compatible) • No Moving Parts • High Reliability • Arc-Free With No Snubbing Circuits • 3750VRMS Input/Output Isolation • FCC Compatible • VDE Compatible • No EMI/RFI Generation • Machine Insertable, Wave Solderable • Surface Mount and Tape & Reel Versions Available • Current Limiting Surface Mount and Tape and Reel Versions Available Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hookswitch • Dial Pulsing • Ground Start • Ringer Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment-Patient/Equipment Isolation • Security • Aerospace • Industrial Controls Approvals • UL Recognized: File Number E76270 • CSA Certified: File Number LR 43639-10 • BSI Certified to: • BS EN 60950:1992 (BS7002:1992) Certificate #: 7344 • BS EN 41003:1993 Certificate #: 7344 Ordering Information Part # LAA125L LAA125LS LAA125LSTR LAA125PL LAA125PLTR Description 8 Pin DIP (50/Tube) 8 Pin Surface Mount (50/Tube) 8 Pin Surface Mount (1,000/Reel) 8 Pin Flat Pack (50/Tube) 8 Pin Flat Pack (1,000/Reel) Pin Configuration LAA125L Pinout AC/DC Configuration + Control - Switch #1 – Control - Switch #1 + Control - Switch #2 – Control - Switch #2 1 8 2 7 3 6 4 5 Load - Switch #1 Load - Switch #1 Load - Switch #2 Load - Switch #2 Switching Characteristics of Normally Open (Form A) Devices 10ms CONTROL LOAD 10%+ +90% TON DS-LAA125L-R9 www.clare.com 10%+ TOFF 1 LAA125L Absolute Maximum Ratings (@ 25˚ C) Parameter Input Power Dissipation Input Control Current Peak (10ms) Reverse Input Voltage Total Power Dissipation Capacitance Input to Output Isolation Voltage nput to Output Operational Temperature Storage Temperature Soldering Temperature DIP Package Flatpack/Surface Mount Package (10 Seconds Max.) 1 2 Min - Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this data sheet is not implied. Exposure of the device to the absolute maximum ratings for an extended period may degrade the device and effect its reliability. Typ Max Units - 1501 mW 50 mA 1 A 5 V - 8002 mW - 3 - pF 3750 -40 -40 - VRMS +85 °C +125 °C - - +260 °C - - +220 °C Derate Linearly 1.33 mw/˚C Derate Linearly 6.67 mw/˚C Electrical Characteristics Parameter Output Characteristics @ 25°C Load Voltage (Peak) Load Current (Continuous) AC/DC Configuration Peak Load Current On-Resistance AC/DC Configuration Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Load Current Limiting Input Characteristics @ 25°C Input Control Current Input Dropout Current Input Voltage Drop Reverse Input Voltage Reverse Input Current Input to Output Capacitance Input to Output Isolation 2 Conditions Symbol Min Typ Max Units - VL - - 350 V 10ms max IL ILPK - - 150 400 mA mA IL=Load Current VL=350V RON ILEAK - - 18 1 Ω µA IF=5mA, VL=10V IF=5mA, VL=10V 50V; f=1MHz TON TOFF COUT ICL 190 50 235 5 5 250 ms ms pF mA IL=170mA IF=5mA VR=5V - IF VF VR IR CI/O VI/O 5 0.4 0.9 3750 0.7 1.2 3 - 50 1.4 5 10 - mA mA V V µA pF VRMS www.clare.com Rev. 9 LAA125L Performance Data* LAA125L Typical On-Resistance Distribution (N=50 Ambient Temperature = 25°C) (Load Current = 170mADC) Device Count (N) Device Count (N) 30 25 20 15 10 5 LAA125L Typical Blocking Voltage Distribution (N=50 Ambient Temperature = 25°C) 35 35 30 30 Device Count (N) 35 LAA125L Typical LED Forward Voltage Drop (N=50 Ambient Temperature = 25°C) IF = 5mADC 25 20 15 10 1.17 1.19 1.21 1.23 14.0 14.4 LED Forward Voltage Drop (V) 14.8 15.2 380 15.6 20 15 10 15 10 5 0 1.33 1.48 0.3 0.5 0.7 LED Current (mA) Load Current (mA) Device Count (N) 30 25 20 15 10 0.9 1.1 1.3 0.23 1.5 0 0.22 250 0.18 200 0.16 150 20mA 10mA 5mA 100 50 0.26 -40 0.30 LAA125L Typical Blocking Voltage vs. Temperature -20 0 20 40 60 80 100 385 380 0 20 40 60 Temperature (°C) 80 100 0.10 -20 0 20 40 60 80 100 LAA125L Typical Turn-On vs. Temperature (Load Current = 170mADC) LAA125L Typical Turn-Off vs. Temperature (Load Current = 170mADC) 0.30 5mA 0.4 10mA 0.3 20mA 0.2 0.25 0.20 0.15 0.10 0.05 5mA 0 0 -20 0.12 Temperature (°C) 0.1 375 0.77 0.14 -40 Turn-Off (ms) 390 0.68 Temperature (°C) 0.5 395 0.59 0.06 120 0.6 Turn-On (ms) Blocking Voltage (VRMS) 400 0.50 0.08 Turn-Off (ms) -40 0.41 LAA125L Typical Leakage vs. Temperature (Measured across Pins 5 & 6 or 7 & 8) 0 0.18 0.32 Turn-On (ms) 5 0.14 10 LAA125L Typical Load Current vs. Temperature 35 0.10 15 LED Current (mA) LAA125L Typical Turn-Off Time (N=50 Ambient Temperature = 25°C) (Load Current = 170mADC; IF = 5mADC) 0.06 20 0 1.63 Leakage (µA) 1.18 400 5 5 0 396 25 20 Device Count (N) Device Count (N) Device Count (N) 25 392 30 25 30 388 LAA125L Typical Turn-On Time (N=50 Ambient Temperature = 25°C) (Load Current = 170mADC; IF = 5mADC) 35 1.03 384 Blocking Voltage (V) LAA125L Typical IF for Switch Dropout (N=50 Ambient Temperature = 25°C) (Load Current = 170mADC) 40 0.88 10 On-Resistance (Ω) LAA125L Typical IF for Switch Operation (N=50 Ambient Temperature = 25°C) (Load Current = 170mADC) 0.73 15 0 0 1.25 20 5 5 0 25 -40 -20 0 20 40 60 Temperature (°C) 80 100 -40 -20 0 20 40 60 80 100 Temperature (°C) The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. Rev. 9 www.clare.com 3 LAA125L Performance Data* LAA125L Typical Turn-On vs.LED Forward Current (Load Current = 170mADC) 1.8 0.40 1.6 0.35 LAA125L Typical Turn-Off vs. LED Forward Current (Load Current = 170mADC) 0.160 0.150 1.4 50mA 30mA 20mA 10mA 5mA 1.2 1.0 0.30 Turn-Off (ms) Turn-On (ms) LED Forward Voltage Drop (V) LAA125L Typical LED Forward Voltage Drop vs. Temperature 0.25 0.20 0.140 0.130 0.120 0.15 0.110 0.8 -40 -20 0 20 40 60 80 100 0.10 120 0 2 4 Temperature (°C) 6 8 10 12 14 16 18 20 0.100 0 LED Forward Current (mA) 2 4 6 8 10 12 14 16 18 20 LED Forward Current (mA) LAA125L Typical On-Resistance vs. Temperature (Load Current = 170mADC; IF = 5mADC) 60 3.000 3.000 2.500 2.500 40 30 20 10 LED Current (mA) 50 LED Current (mA) On-Resistance (Ω) LAA125L Typical IF for Switch Dropout vs. Temperature (Load Current = 170mADC) LAA125L Typical IF for Switch Operation vs. Temperature (Load Current = 170mADC) 2.000 1.500 1.000 2.000 1.500 1.000 0.500 0.500 0 -40 -20 0 20 40 60 80 100 0 0 -40 Temperature (°C) -20 0 20 40 60 80 100 200 LAA125L Typical Load Current vs. Load Voltage (Ambient Temperature = 25°C) IF = 5mADC -20 0 20 40 60 80 100 LAA125L Energy Rating Curve 1.2 150 1.0 Load Current (A) Load Current (mA) -40 Temperature (°C) Temperature (°C) 100 50 0 -50 -100 0.8 0.6 0.4 0.2 -150 -200 -2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 Load Voltage (V) 0 10µs 100µs 1ms 10ms 100ms 1s 10s 100s Time The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com Rev. 9 LAA125L MECHANICAL DIMENSIONS 9.652 ± .381 (.380 ± .015) 8 Pin DIP Through Hole (Standard) 2.540 ± .127 8-.800 DIA. (.100 ± .005) (8-.031 DIA.) 2.540 ± .127 (.100 ± .005) 7.620 ± .254 (.300 ± .010) 7.239 TYP. (.285) PC Board Pattern (Top View) 3.302 (.130) 9.144 ± .508 (.360 ± .020) 6.350 ± .127 (.250 ± .005) 9.144 TYP. (.360) .457 ± .076 (.018 ± .003) 7.620 ± .127 (.300 ± .005) 8.077 ± .127 (.318 ± .005 ) 9.652 ± .381 (.380 ± .015) 8 Pin DIP Surface Mount (“S” Suffix) 4.445 ± .127 (.175 ± .005) 3.302 (.130) .254 TYP. (.010) (.100 ± .005) 9.525 ± .254 (.375 ± .010) 6.350 ± .127 (.250 ± .005) .635 TYP. (.025) PC Board Pattern (Top View) 2.540 ± .127 2.540 ± .127 (.100 ± .005) 7.620 ± .254 (.300 ± .010) 8.305 ± .127 (.327 ± .005) 1.905 ± .127 (.075 ± .005) .457 ± .076 (.018 ± .003) 1.498 ± .127 (.059 ± .005) 8.077 ± .127 (.318 ± .005) 9.652 ± .381 (.380 ± .015) 2.540 ± .127 (.100 ± .005) 8 Pin Flatpack (“P” Suffix) 2.159 TYP. (.085) PC Board Pattern (Top View) 2.540 ± .127 (.100 ± .005) 7.620 ± .254 (.300 ± .010) 2.286 MAX. .635 ± .127 (.090) (.025) 7.620 ± .127 (.300 ± .005) 6.350 ± .127 (.250 ± .005) 6.350 ± .127 (.250 ± .005) 9.398 ± .127 (.370 ± .005) .203 (.008) 8.763 ± .127 (.345 ± .005) 1.193 (.047) .457 ± .076 (.018 ± .003) 8.077 ± .127 (.318 ± .005) .787 (.031) Dimensions mm (inches) Rev. 9 www.clare.com 5 LAA125L MECHANICAL DIMENSIONS Tape and Reel Packaging for 8 Pin Surface Mount Package 330.2 DIA. (13.00) 6.731 MAX. 1.753 ± .102 (.265) (.069 ± .004) .406 MAX. (.016) Top Cover Tape Thickness .102 MAX. (.004) 2.007 ± .102 1.498 ± .102 3.987 ± .102 (.079 ± .004) (.059 ± .004) (.157 ± .004) 7.493 ± .102 (.295 ± .004) 1 16.002 ± .305 (.630 ± .012) 8 12.090 (.476) 10.300 (.405) 4.877 (.192) Top Cover Tape Embossed Carrier .050R TYP. 11.989 ± .102 (.472 ± .004) 10.300 ± .102 (.405 ± .004) 1.549 ± .102 (.061 ± .004) User Direction of Feed Embossment Tape and Reel Packaging for 8 Pin Flatpack Package 330.2 DIA. (13.00) Top Cover Tape Thickness .102 MAX. (.004) 6.731 MAX. 1.753 ± 0.102 (.265) (.069 ± .004) .406 MAX. (.016) 2.007 ± .102 1.498 ± .102 3.987 ± .102 (.079 ± .004) (.059 ± .004) (.157 ± .004) 7.493 ± .102 (.295 ± .004) 1 8 12.090 (.476) 10.287 (.405) 4.877 (.192) Top Cover Tape Embossed Carrier Embossment 16.002 ± .305 (.630 ± .012) .050R TYP. 11.988 ± .102 (.472 ± .004) 10.287 ± .102 (.405 ± .004) 1.549 ± .102 (.061 ± .004) User Direction of Feed Dimensions mm (inches) 6 www.clare.com Rev. 9 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-LAA125L-R9.0 ©Copyright 2002, Clare, Inc. All rights reserved. Printed in USA. 6/25/02