THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS X502 0713 622.08M 3.3V SURFACE MOUNT 5.0 x 7.5mm LVDS CLOCK OSCILLATOR ABSOLUTE M AXIMUM RATING S PARAMETER TABLE 1.0 UNITS MINIMUM NOMINAL MAXIMUM UNITS -55 - 125 °C -0.5 - 4.6 Vdc -0.5 - Vcc+0.5 Vdc MINIMUM NOMINAL MAXIMUM UNITS 200 - 800 MHz -20 - 20 ppm 0 - 70 °C Vdc Storage Temperature Supply Voltage X502 (Vcc) Input Voltage OPERATING SPECIFIC ATIONS NOTE TABLE 2.0 PARAMETER Center Frequency (Fo) Total Frequency Tolerance Operating Temperature Range Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 100 mA Jitter (BW=10Hz to 20MHz) - - 10 ps rms Jitter (BW=12kHz to 80MHz) - - 2 ps rms SSB Phase Noise at 10Hz offset - -75 - dBc/Hz SSB Phase Noise at 100Hz offset - -95 - dBc/Hz SSB Phase Noise at 1KHz offset - -110 - dBc/Hz SSB Phase Noise at 10KHz offset - -125 - dBc/Hz SSB Phase Noise at 100KHz offset - -120 - dBc/Hz NOTE 1 DESCRIPTION The Connor-Winfield X502 is a 3.3V Crystal Controlled Oscillator (XO) with LVDS differential outputs. The X502 is designed for use with PLL systems requiring tight frequency stability vs. change in temperature and high frequency output over the commercial temperature range. The X502 is designed using a 2x or 4x PLL multiplication to achieve the high frequency output. FEATURES INPUT CHARACTERISTICS TABLE 3.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Enable Input Voltage (Low) (Vil) - 0.3Vcc Vdc 2 Disable Input Voltage (High) (Vih) 0.7Vcc - - Vdc 2 MINIMUM NOMINAL MAXIMUM UNITS NOTE - - 100 Ohms 3 250 - 450 mV LVDS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER LOAD Output Differential Voltage (Vod) Duty Cycle at 50% Level Rise / Fall Time 45 50 55 % - 0.6 1.0 nS 3.3V OPERATION LOW JITTER <2pS RMS TOTAL FREQUENCY TOLERANCE: ±20ppm TEMPERATURE RANGE: 0 to 70°C DIFFERENTIAL LVDS OUTPUTS SURFACE MOUNT PACKAGE PACKAG E CHARACTERISTICS TABLE 5.0 Hermetically sealed ceramic package with grounded metal cover. Package RoHS COMPLIANT / LEAD FREE PROCESS RECOMMENDATIONS TABLE 6.0 Solder Reflow Notes 1.0 2.0 3.0 TAPE AND REEL PACKAGING See solder profile on page 2. Includes initial tolerance, deviation over temperature, supply and load variations, shock, vibration and 10 years aging. When oscillator is disabled both output are in a high impedance state (Tri-State) Vod measured with 100 ohm resistor between the true output and the complementary output. ORDERING INFORMATION X502 - 622.08M LVDS CLOCK SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: DS017 PAGE 1 OF 2 REV: 01 DATE: 04/03/07 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Package Layout Suggested Pad Layout X502 0713 622.08M Vcc Top View 1 Pin 1 Top View Bottom View Dimensional Tolerance: ±.005 (.127mm) Output Waveforms Pin Connections Pin 1 2 3 4 5 6 Test Circuit Function N/C Enable / Disable Ground (Case) Output Q Comp Output Q Vcc Solder Profile Temperature Q 260°C 260°C 220°C 180°C Vod 100 ohm 150°C 120°C 2 Q 0 N/C 120 S Max. E/D Time 10 S 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: DS017 PAGE 2 OF 2 REV: 01 DATE: 04/03/07 aCopyright 2001 Connor-Winfield all rights reserved.