THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CW 0602 FPLA554G 155.52M CRYSTAL CONTROLLED OSCILLATORS SURFACE MOUNT 3.3V LVPECL CLOCK ABSOLUTE M AXIMUM RATING S TABLE 1.0 PARAMETER UNITS MINIMUM NOMINAL -40 - 85 °C (Vcc) -0.5 - 7.0 Vdc Storage Temperature Supply Voltage MAXIMUM UNITS FPLA554G NOTE DESCRIPTION OPERATING SPECIFIC ATIONS TABLE 2.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE 44.736 -15 0 - MHz ppm °C 1 - 200 15 70 (Vcc) 3.135 3.3 3.465 Vdc (Icc) - - 60 mA Jitter (BW=10Hz to 20MHz) - - 5 pS RMS Jitter (BW=12kHz to 20MHz) - - 1 pS RMS SSB Phase Noise at 10Hz offset - -60 - dBc/Hz SSB Phase Noise at 100Hz offset - -90 - dBc/Hz SSB Phase Noise at 1KHz offset - -100 - dBc/Hz SSB Phase Noise at 10KHz offset - -125 - dBc/Hz SSB Phase Noise at 10KHz offset - -135 - dBc/Hz NOMINAL MAXIMUM - UNITS NOTE Vdc 2 1.68 Vdc 2 Center Frequency Total Frequency Tolerance Operating Temperature Range (Fo) Supply Voltage Supply Current INPUT CHARACTERISTICS TABLE 3.0 PARAMETER Disable Input Voltage (High) (Vih) MINIMUM 2.275 Enable Input Voltage (Low) (Vil) - - The Connor-Winfield FPLA554G is a fixed frequency, surface mount Crystal Controlled Oscillator (XO) designed for applications requiring low jitter and a ±15ppm overall stability. Operating at 3.3V supply voltage, the FPLA554G provides LVPECL Differential Outputs with enable/disable function. FEATURES 3.3V OPERATION ENABLE/DISABLE FUNCTION PECL OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER LOAD Voltage (High) (Low) (Voh) (Vol) Duty Cycle Rise / Fall Time 20% to 80% MINIMUM NOMINAL MAXIMUM UNITS NOTE 2.275 45 - 50 - 50 1.68 55 1 Ohms Vdc Vdc % nS 3 4 LVPECL DIFFERENTIAL OUTPUTS LOW JITTER <1pS RMS OVERALL FREQUENCY TOLERANCE: ±15PPM TEMPERATURE RANGE: 0 to 70°C PACKAG E CHARACTERISTICS Package PROCESS RECOMMENDATIONS Solder Reflow Wash TABLE 5.0 Non-hermetic package consisting of an FR4 substrate with grounded metal cover. TABLE 6.0 The component solder used internal to this device has a melting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Ultrasonic cleaning is not recommended. Notes 1) Includes initial tolerance, deviation over temperature, supply and load variations, shock, vibration and 10 years aging. 2) When the oscillator is disabled, the true output is in a low state (Vol) and the complementary output is in the high state (VoH). 3) Output must be terminated into 50 ohms to Vcc – 2V or Thevenin equivalent. 4) Duty Cycle measured at 1.977V SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING RoHS COMPLIANT ORDERING INFORMATION FPLA554G - 155.52MHz CLOCK SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Ec223 PAGE 1 OF 2 REV: 00 DATE: 01/12/06 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS CW 0602 FPLA554G 155.52M Pin 1 2 3 4 5 6 7 8 9 10 TABLE 6.0 Connection N/C Enable / Disable N/C Ground N/C Q Output Q Output N/C Vcc N/C Dimensional Tolerance: ±.005 (.127mm) SUGGESTED PAD LAYOUT OUTPUT WAVEFORM “1” LEVEL “0” LEVEL Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 120°C ENABLE/ DISABLE 0 120 S Max. 10 S Time 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Ec223 PAGE 2 OF 2 REV: 00 DATE: 01/12/06 aCopyright 2001 Connor-Winfield all rights reserved.