THE CONNOR-WINFIELD CORP. PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS CERAMIC SURFACE MOUNT 3.3V LVDS 5x7.0mm HIGH FREQUENCY CLOCK OSCILLATOR CW L703 333M 0538 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. HTTP://WWW.CONWIN.COM L703 ABSOLU TE MAX IMUM RATING S PARAMETER TABLE 1.0 UNITS MINIMUM NOMINAL MAXIMUM -55 - 125 °C Supply Voltage (Vcc) -0.5 - 4.6 Vdc Input Voltage (Vcc) -0.5 - Vcc+0.5 Vdc MINIMUM NOMINAL MAXIMUM UNITS 200 - 800 MHz -100 - 100 ppm 0 - 85 °C Vdc Storage Temperature UNITS OPERATING SPECIFIC ATIONS TABLE 2.0 PARAMETER Center Frequency (Fo) Total Frequency Tolerance Operating Temperature Range NOTE 1 Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 60 mA Jitter (BW=10Hz to 20MHz) - - 10 ps rms Jitter (BW=12kHz to 80MHz) - - 3 ps rms SSB Phase Noise at 10Hz offset - -75 - dBc/Hz SSB Phase Noise at 100Hz offset - -95 - dBc/Hz SSB Phase Noise at 1KHz offset - -110 - dBc/Hz SSB Phase Noise at 10KHz offset - -125 - dBc/Hz SSB Phase Noise at 100KHz offset - -120 - dBc/Hz MINIMUM NOMINAL MAXIMUM UNITS NOTE - 0.3Vcc Vdc 2 - Vdc 2 INPUT CHARACTERISTICS Disable Input Voltage (Low) (Vil) - Enable Input Voltage (High) (Vih) 0.7Vcc The Connor Winfield L703 is a Fixed Frequency, Surface Mount Crystal Controlled Oscillator (XO) designed for applications requiring low jitter and a ±100ppm, 0 to 85°C overall overall frequency tolerance, LVDS Differential Outputs and Tri-state Enable / Disable function. The L703 is designed using a 2X or 4X PLL multiplication to achieve the high output frequencies. FEATURES TABLE 3.0 PARAMETER DESCRIPTION NOTE 3.3V OPERATION LVDS DIFFERENTIAL OUTPUTS ENABLE / DISABLE LVDS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE - - 100 Ohms 3 250 - 450 mV LOAD Output Differential Voltage (Vod) Duty Cycle at 50% Level Rise / Fall Time PACKAG E CHARACTERISTICS Package PROCESS RECOMMENDATIONS Solder Reflow 1.0 2.0 3.0 4.0 45 50 55 % - 0.6 1.0 nS LOW JITTER <3pS RMS OVERALL FREQUENCY TOLERANCE ±100ppm 4 TEMPERATURE RANGE: 0 to 85°C SURFACE MOUNT PACKAGE TABLE 5.0 Hermetically sealed ceramic package with grounded metal cover. TABLE 6.0 SMD product suitable for Convection Reflow soldering. Peak temperature 260°C. Maximum time above 220°C, 60 seconds. Notes Includes calibration @ 25°C, frequency stability vs. temperature, supply and load variations, shock, vibration and 20 years aging. When the oscillator is disabled, the outputs are at High Impedance. Output is enabled with no connection on pad 1. Vod measured with 100-ohm resistor between the true output and the complementary output. Duty Cycle measured at 50% of output swing. TAPE AND REEL PACKAGING RoHS COMPLIANT ORDERING INFORMATION L703 CLOCK SERIES - 333MHz CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Ds022 PAGE 1 OF 2 REV: 01 DATE: 05/18/06 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. HTTP://WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS Pin Connection Enable / Disable Function TABLE 7.0 Pin 1 2 3 4 5 6 Function Enable / Disable N/C Ground (Case) Output Q Comp Output Q Vcc Enable / Disable Function (Pad 1) High or Open Low Suggested Pad Layout Package Outline and Dimensions 7 TABLE 8.0 Output Enable Disable (High Impedance) MAX 0 MAX CW L703 333M 0538 .070 MAX (1.8mm) Output Waveform Test Circuit Solder Profile Temperature 260°C Q 260°C 220°C 180°C Vod 100 ohm 150°C 120°C 2 Q E/D 0 120 S Max. N/C 10 S Time 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Ds022 PAGE 1 OF 2 REV: 01 DATE: 05/18/06 aCopyright 2001 Connor-Winfield all rights reserved.