For assistance or to order, call (800) 531-5782 PT6200 SLTS063 Series 2 AMP HIGH-PERFORMANCE ADJUSTABLE ISR WITH ON/OFF CONTROL • • • • • • 90% Efficiency Adjustable Output Voltage Internal Short Circuit Protection Over-Temperature Protection On/Off Control (Ground Off) Small SIP Footprint 0.36" x 1.64" x 0.60"(H) The PT6200 Series is a line of High-Performance 2 Amp, 12-Pin SIP (Single In-line Package) Integrated Switching Regulators (ISRs) designed Pin-Out Information Standard Application VO Adjust 12 9,10 3,4 VIN (+) VOUT (+) PT6100/6200 1 C1 Q1 C2 5,6,7,8 INH Pin No. Function 1 Inhibit 2 N/C 3 Vin 4 Vin 5 GND 6 GND Ordering Information Pin No. Function 7 GND 8 GND 9 Vout 10 Vout 11 N/C 12 Vout Adj COM COM PT6202■ = +5 Volts PT6203■ = +3.3 Volts PT6204■ = +12 Volts (For dimensions, see page 65.) PT Series Suffix (PT1234X) Case/Pin Configuration Vertical Through-Hole Heat Tab Configuration None Side N A C Horizontal Through-Hole C1 = Optional ceramic (1µF) Q1 = NFET C2 = Required 100µF electrolytic Horizontal Surface Mount 1 R G B (See Thermal Application Notes on page 44 for heat tab application data.) 12 Specifications PT6200 SERIES Characteristics (TA=25C unless note d) Symbols Conditions Min Typ Max Units Output Current Io Over Vin range 0.1** — 2.0 Amps Current Limit Icl Vin = Vo + 5V — 3.5 4.5 Amps Short Circuit Current Isc Vin = Vo + 5V — 5.0 — Apk Input Voltage Range Vin 0.1 ≤ Io ≤ 2.0 Amp 7 7.25 14.5 — — — 26 30 30 VDC VDC VDC Static Voltage Tolerance Vo Over Vin Range, Io = 2.0 Amp TA = -40˚ C to shutdown — ±1.0 ±2.0 %Vo Line Regulation Reg line Over Vin range — ±0.25 ±0.5 %Vo Load Regulation Reg load 0.1 ≤ Io ≤ 2.0 Amp — ±0.25 ±0.5 %Vo Ripple/Noise Vn Vin = Vo + 5V, I o = 2.0 Amp — ±2 — %Vo Transient Response with Co = 100µF ttr Vos 50% load change Vo over/undershoot — — 100 3.0 200 5.0 µSec %Vo Efficiency η Vin=8V, I o = 0.5 Amp,Vo = 3.3V Vin=8V, I o = 0.5 Amp,Vo = 5V Vin=15V, I o = 0.5 Amp,Vo = 12V — — — 85 90 93 — — — % % % Switching Frequency ƒo Over Vin and Io ranges, 400 500 500 500 650 650 600 800 800 KHz KHz KHz Shutdown Current Isc Vin = 15V — 100 — µAmp Quiescent Current Inl Io = 0A, Vin =10V — 10 — mAmp Output Voltage Adjustment Range Vo Below Vo Above Vo See Application Notes on page 40. Operating Temperature TA Free Air Convection, (40-60LFM) Over Vin and Io ranges 3.3V 5V 12V -40 -40 -40 — — — +85* +60* Vo = 3.3V Vo = 5V Vo = 12V — — — 25 30 35 — — — C/W -40 — +125 C Vo = 3.3V Vo = 5V Vo = 12V Vo = 3.3V Vo = 5V Vo = 12V C * Thermal Resistance θJA Free Air Convection (40-60LFM) Storage Temperature Ts — Mechanical Shock Per Mil-STD-883D, Method 2002.3 Condition A, 1 msec, Half Sine, mounted to a fixture — — 500 G’s Mechanical Vibration Per Mil-STD-883D, Method 2007.2 Condition A, 20-2000 Hz — — 15 G’s Weight — — — 8.5 — grams Relative Humidity — Non-condensing 0 — 95 % *See Thermal Derating chart. ** ISR will operate down to no load with reduced specifications. Note: The PT6200 Series requires a 100µF electrolytic or tantalum output capacitor for proper operation in all applications. 20 to meet the on-board power conversion needs of battery powered or other equipment requiring high efficiency and small size. This high performance ISR family offers a unique combination of features combining 90% typical efficiency with open-collector on/off control and adjustable output voltage. Quiescent current in the shutdown mode is less than 100µA. Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 For assistance or to order, call C H A R A C T E R I S T I C (800) 531-5782 D A T A PT6203, 3.3 VDC PT6202, 5.0 VDC PT6204, 12.0 VDC (See Note 1) (See Note 1) (See Note 1) Efficiency vs Output Current Efficiency vs Output Current Efficiency vs Output Current 100 100 100 Vin 90 7.0V 80 10.0V 70 12.0V 15.0V 60 90 7.0V 8.0V 80 10.0V 70 15.0V 20.0V 60 Efficiency - % Vin Efficiency - % Efficiency - % 90 50 40 1 1.5 17.0V 70 20.0V 25.0V 60 28.0V 50 28.0V 40 0.5 15.0V 25.0V 20.0V 50 0 Vin 80 40 0 2 0.5 1 1.5 2 0 0.5 Iout-(Amps) Iout-(Amps) Ripple vs Output Current Ripple vs Output Current 150 1 1.5 2 Iout-(Amps) Ripple vs Output Current 150 300 Vin 120 Vin 15.0V 12.0V 60 10.0V 25.0V Ripple-(mV) Ripple-(mV) 90 7.0V 30 250 28.0V 20.0V 90 20.0V 15.0V 60 10.0V Ripple-(mV) 120 1 1.5 2 20.0V 17.0V 100 15.0V 0 0.5 25.0V 150 50 7.0V 0 28.0V 8.0V 30 0 Vin 200 0 0 0.5 1 Iout-(Amps) 1.5 2 0 0.5 Iout-(Amps) Minimum Input Voltage Minimum Input Voltage (See Note 2) 6.5 1 1.5 2 Iout-(Amps) Minimum Input Voltage (See Note 2) 7 14 6.5 13.5 (See Note 2) 6.25 5.75 5.5 Vin-(Volts) Vin-(Volts) Vin-(Volts) 6 6 13 12.5 5.5 5.25 5 12 5 0 0.5 1 1.5 2 0 0.5 1 Iout-(Amps) 1.5 0 2 0.5 1 Thermal Derating (Ta) Thermal Derating (Ta) (See Note 3) 2 Thermal Derating (Ta) (See Note 3) 2 85°C 1.5 2 Iout-(Amps) Iout-(Amps) (See Note 3) 2 60˚C 50°C 60°C 90°C 70˚C 85˚C 70°C 1.5 1.5 1.5 1 0.5 Iout-(Amps) Iout-(Amps) Iout-(Amps) 95°C 1 0.5 0 9 11 13 15 Vin-(Volts) 17 21 19 0 7 Power Dissipation vs Output Current 9 11 13 15 17 19 Vin-(Volts) 21 23 25 27 29 15 Power Dissipation vs Output Current 2.5 85°C 0.5 0 7 1 17 19 21 23 Vin-(Volts) 25 27 29 Power Dissipation vs Output Current 2.5 3 Vin Vin 2 15.0V 12.0V 1 10.0V 7.0V 0.5 25.0V Pd-(Watts) Pd-(Watts) 20.0V 1.5 20.0V 15.0V 1 10.0V Vin 28.0V 2 Pd-(Watts) 2 1.5 2.5 28.0V 25.0V 1.5 20.0V 1 17.0V 15.0V 8.0V 0.5 0.5 7.0V 0 0 0 0 0.5 1 Iout-(Amps) 1.5 2 0 0.5 1 Iout-(Amps) 1.5 2 0 0.5 1 1.5 2 Iout-(Amps) Note 1: All data listed in the above graphs, except for derating data, has been developed from actual products tested at 25˚ C. This data is considered typical data for the ISR. Note 2: Minimum Vin data is typical and is not guaranteed. The data corresponds to a 2% output voltage drop. Note 3: Thermal derating graphs are developed in free air convection cooling of 40-60 LFM with no optional heat tab. (See Thermal Application Notes). Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing PT6202A NRND SIP MOD ULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6202B NRND SIP MOD ULE EBK 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM PT6202C NRND SIP MOD ULE EBC 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM PT6202G NRND SIP MOD ULE EBG 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type OBSOLETE SIP MOD ULE EBJ 12 TBD Call TI Call TI PT6202J Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) PT6202N NRND SIP MOD ULE EBD 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6202R NRND SIP MOD ULE EBE 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type OBSOLETE SIP MOD ULE EBF 12 TBD Call TI Call TI PT6202S PT6203A NRND SIP MOD ULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6203C NRND SIP MOD ULE EBC 12 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM OBSOLETE SIP MOD ULE EBH 12 TBD Call TI Call TI PT6203H PT6203N NRND SIP MOD ULE EBD 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6204A NRND SIP MOD ULE EBA 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6204G NRND SIP MOD ULE EBG 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6204H OBSOLETE SIP MOD ULE EBH 12 TBD Call TI Call TI PT6204J OBSOLETE SIP MOD ULE EBJ 12 TBD Call TI Call TI PT6204N NRND SIP MOD ULE EBD 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6204R NRND SIP MOD ULE EBE 12 12 Pb-Free (RoHS) Call TI N / A for Pkg Type OBSOLETE SIP MOD ULE EBF 12 TBD Call TI Call TI PT6204S (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated