ENPIRION EN5322QI-T

EN5322QI
Created on 3/12/2008 2:55:00 PM
2 A Voltage Mode Synchronous Buck PWM
DC-DC Converter with Integrated Inductor
RoHS Compliant
Halogen Free
General Description
Features
The EN5322 is a high efficiency synchronous
buck converter with integrated inductor, PWM
controller, MOSFETS, and compensation
providing the smallest possible solution size.
• Revolutionary Integrated Inductor
• Total Solution Footprint as Small as 50 mm2
• 4 mm x 6 mm x 1.1 mm QFN Package
• 4 MHz Fixed Switching Frequency
• High Efficiency, up to 95 %
• Low Ripple Voltage; 8 mVP-P Typical
• 2% Initial VOUT Accuracy with VID Codes
• 2% Initial 0.6 V Feedback Voltage Accuracy
• 2.4 V to 5.5 V Input Voltage Range
• 2 A Continuous Output Current Capability
• Fast Transient Response
• Low Dropout Operation: 100 % Duty Cycle
• Power OK Signal with 5 mA Sink Capability
• Dynamic Voltage Scaling with VID Codes
• 17 μA Typical Shutdown Current
• Under Voltage Lockout, Over Current, Short
Circuit, and Thermal Protection
• RoHS Compliant; MSL 3 260 °C Reflow
The 4 MHz operation allows for the use of tiny
MLCC capacitors. It also enables a very wide
control loop bandwidth providing excellent
transient performance and reduced output
impedance. The internal compensation is
designed for unconditional stability across all
operating conditions.
Three VID output voltage select pins provide
seven pre-programmed output voltages along
with an option for external resistor divider.
Output voltage can be programmed on-the-fly to
provide fast, dynamic voltage scaling with
smooth transitions between VID programmed
output voltages.
Applications
•
•
•
•
•
Point of Load Regulation for Low Power
Processors, Network Processors, DSPs’
FPGAs and ASICs
Replacement of LDOs
Noise Sensitive Applications such as A/V and
RF
Computing, Computer Peripherals, Storage,
Networking, and Instrumentation
DSL, STB, DVR, DTV, and iPC
Application Circuit
ENABLE
VIN
VSENSE
PVIN
CIN
VS0
VS1
10 uF
EN5322 POK
COUT
47 uF
VS2
PGND
AVIN
VOUT
VOUT
PGND
AGND
1 uF
Ordering Information
Part Number
EN5322QI-T
EN5322QI-E
Temp Rating (°C)
Package
-40 to +85
24-pin QFN T&R
QFN Evaluation Board
©Enpirion 2008 all rights reserved, E&OE
03454
Figure 1. Typical Application Circuit
1
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Absolute Maximum Ratings
CAUTION: Absolute maximum ratings are stress ratings only. Functional operation beyond recommended operating
conditions is not implied. Stress beyond absolute maximum ratings may cause permanent damage to the device.
Exposure to absolute maximum rated conditions for extended periods may affect device reliability.
Absolute Maximum Electrical Ratings
MIN
Voltages on: PVIN, AVIN, VOUT
Voltages on: VSENSE, VS0, VS1, VS2, ENABLE, POK
Voltage on: VFB
ESD Rating (Human Body Model)
ESD Rating (Charge Device Model)
MAX
-0.3 V
-0.3 V
-0.3 V
2 kV
500 V
6.5 V
VIN
2.7 V
-40 °C
-65 °C
+85 °C
+150 °C
+260 °C
Absolute Maximum Thermal Ratings
Ambient Operating Range
Storage Temperature Range
Reflow Peak Body Temperature MSL3 (10 s)
Thermal Characteristics
SYMBOL
PARAMETER
MIN
TYP
MAX
Thermal Shutdown
TSD
155
Thermal Shutdown Hysteresis
TSDH
15
Thermal Resistance: Junction to Case (0 LFM)
6
θJC
Thermal Resistance: Junction to Ambient (0 LFM)*
36
θJA
* Based on a 2 oz. copper board and proper thermal design in line with JEDEC EIJ-JESD51 standards
UNITS
°C
°C
°C/W
°C/W
Recommended Operating Conditions
PARAMETER
SYMBOL
MIN
Input Voltage Range
VIN
2.4
Output Voltage Range
VOUT
0.6
Output Current
ILOAD
0
Operating Junction Temperature
TJ
-45
Note: VDROPOUT is defined as (ILOAD x Dropout Resistance) including temperature effect.
VIN
MAX
5.5
- VDROPOUT
2
+125
UNITS
V
V
A
°C
Electrical Characteristics
VIN = 5 V and TA = 25 °C, unless otherwise noted.
PARAMETER
Operating Input Voltage
Under Voltage Lockout
UVLO Hysteresis
Output Voltage with VID
Codes (Note 1)
VFB Voltage
SYMBOL
VIN
VUVLO
MIN
2.4
VIN going low to high
VOUT
TA = 25 °C; VIN = 5V
ILOAD = 100 mA
VS2 VS1 VS0 VOUT (V)
0
0
0
3.3
0
0
1
2.5
0
1
0
1.8
0
1
1
1.5
1
0
0
1.25
1
0
1
1.2
1
1
0
0.8
VFB
TA = 25 °C; VIN = 5V
©Enpirion 2008 all rights reserved, E&OE
03454
TEST CONDITIONS
2
4/24/2009
TYP
MAX
5.5
2.2
0.15
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
-2.0
0.588
+2.0
+2.0
+2.0
+2.0
+2.0
+2.0
+2.0
0.600
0.612
UNITS
V
V
V
%
V
www.enpirion.com
Rev:A
EN5322QI
PARAMETER
SYMBOL
Output Voltage with VID
Codes (Note 1)
VFB Voltage
VOUT
2.4 V ≤ VIN ≤ 5.5 V, ILOAD = 0 ~ 2 A,
-40°C ≤ TA ≤ +85°C
VS2 VS1 VS0 VOUT (V)
0
0
0
3.3
0
0
1
2.5
0
1
0
1.8
0
1
1
1.5
1
0
0
1.25
1
0
1
1.2
1
1
0
0.8
VFB
2.4 V ≤ VIN ≤ 5.5 V, ILOAD = 0 ~ 2 A,
VS0 = VS1 = VS2 = 1,
-40°C ≤ TA ≤ +85°C
Dynamic Voltage Slew Rate
Soft Start Slew Rate
VFB, ENABLE, VS0-VS2
Pin Input Current (Note 2)
ENABLE, VS0-VS2 Voltage
Threshold
POK Upper Threshold
POK Upper Threshold
POK Lower Threshold
POK Lower Threshold
POK Low Voltage
POK Pin VOH Leakage
Current
Shutdown Current
Quiescent Current
Quiescent Current
MIN
Logic Low
Logic High
VOUT Rising
VOUT Falling
VOUT Rising
VOUT Falling
ISINK = 5 mA, -40°C ≤ TA ≤ +85°C
0.582
0.600
0.975
0.975
1.5
1.5
0.0
1.4
111
102
92
90
0.15
POK High, -40°C ≤ TA ≤ +85°C
ENABLE Low
No Switching
Switching, VOUT = 1.2 V
2.4 V ≤ VIN ≤ 5.5 V,
-40°C ≤ TA ≤ +85°C
2.1
FOSC
©Enpirion 2008 all rights reserved, E&OE
3
4/24/2009
MAX
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
-3.0
-3.0
-3.0
-3.0
-3.0
-3.0
-3.5
COUT = 1 x 47 μF 1206 X5R MLCC,
VOUT = 1.2 V, ILOAD = 2 A
Output Ripple Voltage
VRIPPLE
COUT = 2 x 22 μF 0805 X5R MLCC,
VOUT = 1.2 V, ILOAD = 2 A
Note 1: The tolerances hold true only if VIN is greater than (VOUT + VDROPOUT).
Note 2: VFB, ENABLE, VS0-VS2 pin input current specification is guaranteed by design.
03454
TYP
-40°C ≤ TA ≤ +85°C
Current Limit Threshold
PFET On Resistance
NFET On Resistance
Dropout Resistance
Operating Frequency
TEST CONDITIONS
ILOAD = 100 mA, VS0 = VS1 = VS2 = 1
0.618
2.025
2.025
UNITS
%
V
V/ms
V/ms
+/-40
nA
0.4
VIN
V
0.4
%
%
%
%
V
500
nA
17
800
15
μA
μA
mA
3.0
A
160
60
200
4
mΩ
mΩ
mΩ
MHz
300
14
mVP-P
8
mVP-P
www.enpirion.com
Rev:A
EN5322QI
Pin Configuration
Figure 2. Pin Diagram, Top View.
Pin Description
PIN
NAME
1, 21-24
NC(SW)
2-3, 8-9
PGND
4-7
VOUT
10-12
VS2-0
13
VSENSE
14
VFB
15
AGND
16
AVIN
17
POK
18
ENABLE
19-20
PVIN
FUNCTION
No Connect. These pins are internally connected to the common drain output of the internal
MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or
voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result
in part malfunction or damage.
Input/Output Power Ground. Connect these pins to the ground electrode of the input and
output filter capacitors. Refer to Layout Considerations section for details.
Voltage and Power Output. Connect these pins to output capacitor(s).
Output Voltage Select. These pins set one of seven preset output voltages and the external
divider option (refer to Electrical Characteristics table for more details), and can be directly
pulled up to VIN or pulled down to GND; these pins must not be left floating.
Sense Pin for Internally Programmed Output Voltages with VID Codes. For either VID code or
external resistor divider applications, connect this pin to the last local output filter capacitor for
internal compensation.
Feedback Pin for External Voltage Divider Network. Connect a resistor divider to this pin to set
the output voltage. Use 340 kΩ, 1% or better for the upper resistor.
Analog Ground for the Controller Circuits
Analog Voltage Input for the Controller Circuits. Connect this pin to the input power supply.
Use a 1 μF bypass capacitor on this pin.
Power OK with an Open Drain Output. Refer to Power OK section.
Input Enable. A logic high signal on this pin enables the output and initiates a soft start. A
logic low signal disables the output and discharges the output to GND. This pin must not be
left floating.
Input Power Supply. Connect to input supply. Decouple with input capacitor(s) to PGND.
©Enpirion 2008 all rights reserved, E&OE
03454
4
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Functional Block Diagram
PVIN
POK
UVLO
POK
Thermal Limit
Current Limit
ENABLE
NC (SW)
Soft Start
P-Drive
Logic
(-)
VOUT
PWM
Comp
(+)
N-Drive
PGND
VSENSE
Sawtooth
Generator
Compensation
Network
(-)
Switch
VFB
Error
Amp
(+)
DAC
BIAS
Voltage
Select
VREF
Package Boundary
AVIN
AGND
VS0 VS1 VS2
Figure 3. Functional Block Diagram.
©Enpirion 2008 all rights reserved, E&OE
03454
5
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
RPOK*
VIN
100k
ENABLE
VOUT
VS0
VS1
10 uF
VOUT
VSENSE
PVIN
CIN
POK
EN5322 POK
AVIN
COUT
47 uF
VS2
PGND
PGND
AGND
1 uF
* Leave RPOK open if the POK function is not used.
Figure 4. Typical Application Circuit with VID Codes.
(NOTE: Enable can be separated from PVIN if the application requires it)
Typical Performance Characteristics
Circuit of Figure 4, VIN = 5 V, VOUT = 1.2 V and TA = 25°C, unless otherwise noted.
Efficiency vs. Load Current (Vin = 3.3V)
95
95
90
90
85
85
Efficiency (%)
Efficiency (%)
Efficiency vs. Load Current (Vin = 5.0V)
80
75
70
65
60
55
75
70
65
60
55
50
50
0.00
0.25
0.50
0.75
1.00
1.25
1.50
1.75
2.00
Load Current (A)
©Enpirion 2008 all rights reserved, E&OE
0.00
0.25
0.50
0.75
1.00
1.25
1.50
1.75
2.00
Load Current (A)
Top to Bottom: VOUT = 3.3 V, 2.5 V, 1.8 V, 1.5 V, 1.2 V,
0.8 V
03454
80
6
4/24/2009
Top to Bottom: VOUT = 2.5 V, 1.8 V, 1.5 V, 1.2 V, 0.8 V
www.enpirion.com
Rev:A
EN5322QI
Quiescent Current (Switching) vs.
Input Voltage
Quiescent Current (mA)
Quiescent Current (uA)
Quiescent Current (No Switching) vs.
Input Voltage
840
820
800
780
760
740
2
3
4
5
18
16
14
12
10
8
2
6
3
6
Load Regulation (Vin = 5 V)
Load Regulation (Vin = 5 V)
1.208
3.304
1.204
Output Voltage (V)
Output Voltage (V)
5
Input Voltage (V)
Input Voltage (V)
1.200
1.196
1.192
1.188
3.300
3.296
3.292
3.288
3.284
1.184
0
0.4
0.8
1.2
1.6
0
2
Load Current (A)
0.4
0.8
1.2
1.6
2
Load Current (A)
Output Ripple at 2 A Load (CH2: VOUT)
Output Ripple at 2 A Load (CH2: VOUT)
VIN = 3.3 V, VOUT = 1.2 V, COUT = 1 x 47 μF
VIN = 3.3 V, VOUT = 1.2 V, COUT = 2 x 22 μF
©Enpirion 2008 all rights reserved, E&OE
03454
4
7
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Transient Response at VIN = 5 V
VOUT = 1.2V, COUT = 1 x 47 μF
(0-2 A Load Step, slew rate ≥ 10A/uS)
CH1: VOUT, CH4: ILOAD
Transient Response at VIN = 5 V
VOUT = 3.3V, COUT = 1 x 47 μF
(0-2 A Load Step, slew rate ≥ 10A/uS)
CH1: VOUT, CH4: ILOAD
VOUT Scaling with VID Codes at VIN = 5 V
(VOUT = 1.2 V – 2.5 V, IOUT = 0 – 2 A)
CH1: VS2, CH2: VOUT, CH3: POK
VOUT Scaling with VID Codes at VIN = 3.3 V
(VOUT = 1.2 V – 2.5 V, IOUT = 0 – 2 A)
CH1: VS2, CH2: VOUT, CH3: POK
Power Up/Down at No Load (VIN = 5 V, VOUT = 1.2 V)
CH1: ENABLE, CH2: VOUT, CH3: POK, CH4: IINDUCTOR
Power Up/Down at 0.6 Ω Load (VIN = 5 V, VOUT = 1.2 V)
CH1: ENABLE, CH2: VOUT, CH3: POK, CH4: IINDUCTOR
©Enpirion 2008 all rights reserved, E&OE
03454
8
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Output Over Load at No Load (VIN = 5 V, VOUT = 1.2 V)
CH2: VOUT, CH3: POK, CH4: IINDUCTOR
Output Over Load at 2 A Load (VIN = 5 V, VOUT = 1.2 V)
CH2: VOUT, CH3: POK, CH4: IINDUCTOR
Output Over Load at No Load (VIN = 5 V, VOUT = 1.2 V)
CH2: VOUT, CH3: POK, CH4: IINDUCTOR
Output Over Load at 2 A Load (VIN = 5 V, VOUT = 1.2 V)
CH2: VOUT, CH3: POK, CH4: IINDUCTOR
Functional Description
The EN5322 leverages advanced CMOS
technology
to
provide
high
switching
frequency, while also maintaining high
efficiency.
impedance and excellent load transient
response.
No
external
compensation
components are needed for most applications.
Packaged in a 4 mm x 6 mm x 1.1 mm QFN,
the EN5322 provides a high degree of flexibility
in circuit design while maintaining a very small
footprint. High switching frequency allows for
the use of very small MLCC input and output
filter capacitors.
Output voltage is chosen from one of seven
preset values via a three-pin VID voltage select
scheme. An external divider option enables the
selection of any output voltage ≥ 0.6 V. The
VID pins can be toggled dynamically to
implement glitch-free dynamic voltage scaling
between any two VID preset values.
The converter uses voltage mode control to
provide high noise immunity, low output
POK monitors the output voltage and signals if
it is within ±10% of nominal. Protection
©Enpirion 2008 all rights reserved, E&OE
03454
9
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Enable
features include under voltage lockout (UVLO),
over current protection, short circuit protection,
and thermal overload protection.
The ENABLE pin provides means to shut down
the converter or initiate normal operation. A
logic high will enable the converter to go
through the soft start cycle and regulate the
output voltage to the desired value. A logic low
will allow the device to discharge the output
and go into shutdown mode for minimal power
consumption. When the output is discharged,
an auxiliary NFET turns on and limits the
discharge current to 300 mA or below. In
shutdown mode, the device typically drains
17μA. The ENABLE pin must not be left
floating.
Stability over Wide Range of Operating
Conditions
The EN5322 utilizes an internal compensation
network and is designed to provide stable
operation over a wide range of operating
conditions. To improve transient performance
or reduce output voltage ripple with dynamic
loads you have the option to add
supplementary capacitance to the output. The
EN5322 is stable with up to 60 μF of output
capacitance without compensation adjustment.
Additional output capacitance above 60 μF can
be
accommodated
with
compensation
adjustment depending on the application. The
high switching frequency allows for a wide
control loop bandwidth.
Thermal Shutdown
When excessive power is dissipated in the
device, its junction temperature rises. Once the
junction temperature exceeds the thermal
shutdown temperature 155 °C, the thermal
shutdown circuit turns off the converter,
allowing the device to cool. When the junction
temperature drops 15 °C, the device will be reenabled and go through a normal startup
process.
Soft Start
The internal soft start circuit limits inrush
current when the device starts up from a power
down condition or when the ENABLE pin is
asserted “high”. Digital control circuitry sets the
VOUT ramp rate to minimize input voltage ripple
and inrush current to ensure a glitch-free start
up. The soft start ramp rate is nominally 1.5
V/ms.
Power OK
The EN5322 provides an open drain output to
indicate if the output voltage stays within 92%
to 111% of the set value. Within this range, the
POK output is allowed to be pulled high.
Outside this range, POK remains low.
However, during transitions such as power up,
power down, and dynamic voltage scaling, the
POK output will not change state until the
transition is complete for enhanced noise
immunity.
Over Current/Short Circuit Protection
When an over current condition occurs, VOUT is
pulled low. This condition is maintained for a
period of 1.2 ms and then a normal soft start
cycle is initiated. If the over current condition
still persists, this cycle will repeat.
Under Voltage Lockout
The POK has 5 mA sink capability for events
where it needs to feed a digital controller with
standard CMOS inputs. When POK is pulled
high, the pin leakage current is as low as 500
nA maximum over temperature. This allows a
large pull up resistor such as 100 kΩ to be
used for minimal current consumption in
shutdown mode.
An under voltage lockout circuit will hold off
switching during initial power up until the input
voltage reaches sufficient level to ensure
proper operation. If the voltage drops below the
UVLO threshold the lockout circuitry will again
disable switching. Hysteresis is included to
prevent chattering between UVLO high and low
states.
The POK output can also be conveniently used
as an ENABLE input of the next stage for
power sequencing of multiple converters.
©Enpirion 2008 all rights reserved, E&OE
03454
10
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Figure 5. Typical Application Circuit with External Resistor Divider.
(NOTE: Enable can be separated from PVIN if the application requires it)
Application Information
values is indeterminate. These pins must not
be left floating.
Setting the Output Voltage
To provide the highest degree of flexibility in
choosing output voltage, the EN5322QI uses a
3 pin VID (Voltage ID) output voltage select
arrangement. This allows the designer to
choose one of seven preset voltages, or to use
an external voltage divider. Figure 4 shows a
typical application circuit with VID codes.
Internally, the output of the VID multiplexer
sets the value for the voltage reference DAC,
which in turn is connected to the non-inverting
input of the error amplifier. This allows the use
of a single feedback divider with constant loop
gain and optimum compensation, independent
of the output voltage selected.
Table 1. VID voltage select settings.
VS2
0
0
0
0
1
1
1
1
03454
VS0
0
1
0
1
0
1
0
1
VOUT
3.3V
2.5V
1.8V
1.5V
1.25V
1.2V
0.8V
User
Selectable
External Voltage Divider
Table 1 shows the various VS0-VS2 pin logic
states and the associated output voltage
levels. A logic “1” indicates a connection to VIN
or to a “high” logic voltage level. A logic “0”
indicates a connection to ground or to a “low”
logic voltage level. These pins can be either
hardwired to VIN or GND or alternatively can be
driven by standard logic levels. Logic low is
defined as VLOW ≤ 0.4V. Logic high is defined
as VHIGH ≥ 1.4V. Any level between these two
©Enpirion 2008 all rights reserved, E&OE
VS1
0
0
1
1
0
0
1
1
As described above, the external voltage
divider option is chosen by connecting the
VS0, VS1, and VS2 pins to VIN or logic “high”.
The EN5322QI uses a separate feedback pin,
VFB, when using the external divider. VSENSE
must be connected to VOUT as indicated in
Figure 5.
11
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
applications for minimal current drain from the
voltage source and good noise immunity. POK
can sink up to 5mA.
If the external voltage divider option is chosen,
use 340 kΩ, 1% or better for the upper resistor
Ra. Then the value of the bottom resistor Rb in
kΩ is given as:
Rb =
Layout Considerations
Proper layout and placement of external
components is critical to optimal functioning of
the converter and for minimizing radiated and
conducted noise.
204
kΩ
VOUT − 0.6
Where VOUT is the output voltage. Rb should
also be a 1% or better resistor.
Follow
these
layout
guidelines
as
demonstrated on the EN5322 customer eval
boards:
1. Input and output capacitors should be
placed on the same side of the PCB as
the EN5322 and immediately adjacent to
their respective pins on the package. To
minimize parasitic inductances, the traces
for making these connections should be
as short and wide as possible.
2. A row of vias connecting these capacitors’
ground pads to the PCB GND plane
should be placed along the edge of the
capacitor ground copper closest to the
positive capacitor pads. These vias
should start as close to the device as
possible and continue underneath the
capacitors.
3. Avoid adding a test pin or test pad for
NC(SW) pins on the PCB. Doing so can
compromise the GND plane and result in
degradation of the performance.
4. There should be as many vias as possible
connecting the thermal pad under the
device to the PCB GND plane for best
thermal performance. Ideally, the vias
should have a drill diameter of 0.33 mm
(10 mils) with at least 1 oz copper plating
in the barrel.
5. Keep the input and output current loops
separate from each other as much as
possible. Keep sensitive signals on the
PCB away from the power supply circuit.
6. Connect the VSENSE trace to the last
local output capacitor. Make sure the
trace inductance between the output
capacitors and the sensing point is
minimized. The VSENSE trace should
also be kept away from noisy signals that
can contaminate it.
Input and Output Capacitor Selection
Low ESR MLC capacitors with X5R or X7R or
equivalent dielectric should be used for input
and output capacitors. Y5V or equivalent
dielectrics lose too much capacitance with
frequency, DC bias, and temperature.
Therefore, they are not suitable for switchmode DC-DC converter filtering, and must be
avoided.
A 10 μF, 10 V, 0805 MLC capacitor is needed
on PVIN for all applications. A 1 μF, 10 V, 0402
MLC capacitor on AVIN is needed for high
frequency bypass to ensure clean chip supply
for optimal performance.
A 47 μF, 6.3 V, 1206 MLC capacitor is
recommended on the output for most
applications. The output ripple can be reduced
by approximately 50% by using 2 x 22 μF,
6.3V, 0805 MLC capacitors rather than 1 x 47
μF.
Table 2. Recommended input and output capacitors
CIN
COUT
Description
Mfg.
P/N
10μF, 10V,
X5R, 10%,
0805
47μF, 6.3V,
X5R, 20%,
1206
Taiyo Yuden
Murata
Panasonic
Taiyo Yuden
Murata
Kemet
LMK212BJ106KG
GRM21BR71A106KE51L
ECJ-2FB1A106K
JMK316BJ476ML
GRM31CR60J476ME19L
C1206C476M9PACTU
POK Pull Up Resistor Selection
POK can be pulled up through a resistor to any
voltage source as high as VIN. The simplest
way is to connect POK to the power input of
the converter through a resistor. A 100 kΩ pull
up resistor is typically recommended for most
©Enpirion 2008 all rights reserved, E&OE
03454
12
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
7.
When using multiple converters on the
same PCB, try to minimize any crosstalk
between them:
Keep the input circuit of any converter
away from the output circuit of any
other converter.
Isolate the input circuits from each
other by connecting all the inputs to a
common
point
using
a
star
connection. Add a 2.2 μF bypass
capacitor to the GND plane at the star
connection. Some applications may
benefit from an SMT ferrite bead
between the input capacitor of each
converter and the star connection
point.
©Enpirion 2008 all rights reserved, E&OE
03454
13
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Design Considerations for Lead-Frame Based Modules
Exposed Metal Pads on Package Bottom
QFN lead-frame based package technology utilizes exposed metal pads on the bottom of the
package that provide improved thermal dissipation and low package thermal resistance, smaller
package footprint and thickness, large lead size and pitch, and excellent lead co-planarity. As the
EN5322 package is a fully integrated module consisting of multiple internal devices, the lead-frame
provides circuit interconnection and mechanical support of these devices resulting in multiple
exposed metal pads on the package bottom.
Only the two large thermal pads and the perimeter leads are to be mechanically/electrically
connected to the PCB through a SMT soldering process. All other exposed metal is to remain free of
any interconnection to the PCB. Figure 6 shows the recommended PCB metal layout for the EN5322
package. A GND pad with a solder mask "bridge" to separate into two pads and 24 signal pads are to
be used to match the metal on the package. The PCB should be clear of any other metal, including
traces, vias, etc., under the package to avoid electrical shorting.
Figure 6. Recommended Footprint for PCB.
©Enpirion 2008 all rights reserved, E&OE
03454
14
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Package and Mechanical
©Enpirion 2008 all rights reserved, E&OE
03454
15
4/24/2009
www.enpirion.com
Rev:A
EN5322QI
Additional Products
Part Number
EP5352QI
EP5362QI
EP5382QI
EP5368QI
EN5311QI
EN5335QI
EN5336QI
EN5365QI
EN5366QI
Description
500 mA dc-dc with integrated inductor; 5 mm x 4 mm x 1.1 mm package
600 mA dc-dc with integrated inductor; 5 mm x 4 mm x 1.1 mm package
800 mA dc-dc with integrated inductor; 5 mm x 4 mm x 1.1 mm package
600 mA dc-dc with integrated inductor; 3 mm x 3 mm x 1.1 mm package
1 A dc-dc with integrated inductor; 5 mm x 4 mm x 1.1 mm package
3 A dc-dc with integrated inductor; 10 mm x 7.5 mm x 1.85 mm QFN package
3-Pin VID VOUT programming
3 A dc-dc with integrated inductor; 10 mm x 7.5 mm x 1.85 mm QFN package
External resistor divider VOUT programming
6 A dc-dc with integrated inductor; 12 mm x 10 mm x 1.85 mm QFN package
3-Pin VID VOUT programming; Parallel capable
6 A dc-dc with integrated inductor; 12 mm x 10 mm x 1.85 mm QFN package
External resistor divider VOUT programming; Parallel capable
Contact Information
Enpirion, Inc.
685 Route 202/206
Suite 305
Bridgewater, NJ 08807
Phone: 908-575-7550
Fax: 908-575-0775
Enpirion reserves the right to make changes in circuit design and/or specifications at any time without notice. Information furnished by Enpirion is
believed to be accurate and reliable. Enpirion assumes no responsibility for its use or for infringement of patents or other third party rights, which may
result from its use. Enpirion products are not authorized for use in nuclear control systems, as critical components in life support systems or equipment
used in hazardous environment without the express written authority from Enpirion..
©Enpirion 2008 all rights reserved, E&OE
03454
16
4/24/2009
www.enpirion.com
Rev:A