EiceDRIVER™ 2ED300C17-S 2ED300C17-ST Dual IGBT Driver for Medium and High Power IGBTs Datasheet and Application Note Prepared by : M.Hornkamp Date of publication: 16.05.2003 Approved by: Reg.Nr.064-02 Revision: 3.0 SN: 23925 Status: SN:24816 preliminary eupec GmbH Max-Planck-Straße 5 D-59581 Warstein Author:Michael Hornkamp Tel. +49(0)2902 764-0 Fax +49(0)2902 764-1150 Email: [email protected] www.eupec.com Technical Information EiceDRIVER™ 2ED300C17-S preliminary Passing on of this document or its contents to company external personnel requires written consent. Usage and copying of the contents to other media is prohibited. Violations will be prosecuted for damages. All rights reserved, including such arising from issue of patents or registration of trade marks or design. © eupec GmbH 2002. All rights reserved. Correspondence of the contents of this document with the described hardware has been checked. Discrepancies may exist nevertheless; no guaranty is assumed for total congruence. The information contained in this document is subject to regular revision. Any alterations required will be incorporated in the next issue. Suggestions for improvement are welcome. Changes of the document may occur without prior notice. Safety notice! It must be prevented that children and the general public have access to the installed driver or can get into proximity! The driver may only be used for the purposes prescribed by the manufacturer. Inadmissible alterations and use of spare parts and accessories not recommend by the manufacturer of the driver can cause fire, electric shock and injuries. This document has to be at the disposal of all users, developers and qualified personnel who are to work with the driver. If measurements and tests on the live device have to be carried out, then the regulations of the Safety Code VBG 4.0 are to be observed, in particular § 8 “Admissible deviations during work on live parts“. Suitable electronic devices are to be used. Prior to installation and commissioning please read this document thoroughly. • Commissioning is prohibited if there is visible damage by inappropriate handling or transport. • Contact while uninstalled is permitted only with ESD protection. • Install only without supply voltage. • Always keep sufficient safety distance during commissioning without closed protective housing. • Contact under live condition is strictly prohibited. • Work after turn-off is not admissible until the absence of supply voltage has been verified. • During work after turn-off it has to be observed that components heat up during operation. Contact with these can cause burning. • The drivers are mounted electrically and mechanically into a mother board by soldering. The mechanical strength has to be verified by the user and, if necessary, assured with appropriate tests. • The drivers are designed for use with eupec IGBT Modules type IHM, EconoPACK+, 62mm. In case of ulterior use, safe operation cannot be guaranteed. www.eupec.com www.EiceDRIVER.com Page 2 Technical Information EiceDRIVER™ 2ED300C17-S preliminary General Information 2ED300C17-S: This datasheet describes the dual channel IGBT driver 2ED300C17-S for industrial application and the 2ED300C17-ST for traction application. The Drivers are separated in two temperature classes –25°C for the 2ED300C17-S and –40°C for the 2ED300C17ST. The electrical function and the mechanic dimension are in both version similar. Only if there is a different in the types the 2ED300C17-ST is called. The 2ED300C17-S is one of the EiceDRIVERTM driver family. (eupec IGBT controlled efficiency DRIVER). The 2ED300C17-S IGBT driver is designed for use with eupec IGBT modules of the 1200V and 1700V series. Functions of the 2ED300C17-S such as the “soft shut down” or the VCEsat reference curves have to be adapted to the individual modules. This is described in the following chapters. The 2ED300C17-S is designed for applications with high safety and reliability requirements and aims for power ratings of 75kW to 1MW. To offer high interference suppression, +15V is generally used for control. The entire logic processing is also done with +15V. The integrated transformer is separated into three sections: Two pulse transformers and a dual channel DC-DC switch mode power supply. These are designed such that they offer lowest coupling capacitances and high isolation stability. The 2ED300C17-S is additionally equipped with a feed-back ”Sense” input. This input can optionally be connected with the active clamping or di/dt and dv/dt control. The clearance and creepage distances comply with VDE0110 and VDE0160 / EN50178 and are designed for pollution degree 3. Materials of the transformer meet requirements of UL94V0. Protection degree IP00. To protect from undefined switching of IGBTs in case of a gate-emitter short circuit of another IGBT, the supply voltage VA;B+; VA;B- is internally monitored in the driver for short circuit currents. In case of a gate-emitter short the secondary circuit is interrupted and thus the primary voltage maintained. Exclusion clause: The datasheet is part of the eupec IGBT driver 2ED300C17-S. To guaranty safe and fault free operation it is necessary to have read and understood this datasheet. The eupec IGBT driver 2ED300C17-S is only intended for control of eupec IGBT modules. The company eupec GmbH cannot warrant against damage and/or dysfunction if IGBT modules used not produced by eupec. In this context, eupec GmbH retains the right to change technical data and product specifications without prior notice to the course of improvement. www.eupec.com www.EiceDRIVER.com Page 3 Technical Information EiceDRIVER™ 2ED300C17-S preliminary Chapter: Page •Safety notice •General information •Exclusion clause •Contents 2 3 3 4 1. 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 Datasheet •Features •Key data •Block diagram •Inputs and outputs •Pin configuration •Maximum permissible values •Characteristic values •Max. switching frequency at different rated currents •Mechanical dimensions 5 5 5 6 6 7 8 9 10 11 2. 2.1 The transformer • Safe electrical isolation Protection Class II according to EN50178 12 12 3. 3.1 3.1.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 Application of the 2ED300C17-S •Power supply •Use of the internal over-current shut-down •Mode selection •Interlock delay times •Logic levels (reset; fault output) •Signal level •IGBT connection •IGBT Shot circuit / IGBT overload shut down •SSD “soft shut down” •External fault input •“Sense” input (SSD and active clamping) •Additional output voltage / buffer capacitors •Application example 2ED300C17-S 13 13 4. 4.1 4.2 4.3 General Designation and symbols Module internal gate resistors Type designation 29 29 30 32 www.eupec.com www.EiceDRIVER.com 14 15 16 17 17 20 23 25 25 27 28 Page 4 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.2 Features • Dual channel IGBT driver 2ED300C17-S • For 1200V / 1700V eupec IGBT modules • VCE sat monitoring • “Soft Shut Down” for fault conditions • Save electrical isolation according to EN50178 • Integrated DC-DC SMPS • High peak output current • ±15V secondary drive voltage • Short signal transition time • Optional “Sence” function • High RFI immunity 1.3 Key data Isolation testing voltage Visol pulse transformer and DC/DC 5000 VAC ±30 A 4 W according to EN50178 protection class II Max. output current: IG per channel Max. output power PDC/DC per channel Signal transition time tpd (on); tpd (off) <670 ns Minimal pulse suppression tmd turn on and turn off 400 ns PWM drive voltage Vin drive level for channel A and B +15 V Supply voltage Operating voltage VDC to ground +15 VDC dv/dt stability dv/dt ( * during test) Operating temperature direct on driver surface Top Operating temperature direct on driver surface Top www.eupec.com 50* kV/µs 2ED300C17-S -25 bis 85 °C 2ED300C17-ST -40 bis 85 °C www.EiceDRIVER.com Page 5 Technical Information EiceDRIVER™ 2ED300C17-S 1.4 Block diagram 2ED300C17-S preliminary EDFA E. A VCEsat VCE sat A Fault Detection Gate A IN A Dead time Pulse Stage CA IN B Pulse Former Softshut down Undervoltage Pulse Memory COM A VA+ VASense A Dead time CB Sense A DOCD RC A EDFA E. B VCEsat VCE sat B Fault Detection Logic MODE Fault Detection Gate B Pulse Stage RESET FAULT FaultMemory VDD VDC Supply Voltage Pulse Former Softshut down Undervoltage Pulse Memory COM B VB+ VBSense B DC/DC Converter DOCD Control GND Sense B RC B 1.5 Inputs and outputs 2ED300C17-S IN A; IN B PWM signal inputs for channel A and channel B CA; CB Inputs for external interlock delay time generation for channel A and B in half bridge mode Mode Input for operating mode selection. Direct mode GND; half bridge mode +15V Reset With reset and operating PWM signals the primary fault memory is reset. Reset has active high logic. A high signal activates the reset. Fault The fault output indicates a fault. The fault output is open collector. VDC Supply for the DC-DC SMPS VDD Electronic supply GND GND is ground and reference point for all primary signals and the supply voltage E.A; E.B External fault input. Is used to set the fault memory by an external signal. VCE sat A; B Input for the saturation voltage monitoring Gate A; B Driver output to the IGBT module gate via an external gate resistor COM A; B COM A; B is connected to the auxiliary emitters of the IGBT module VA+; VA- ; VB+; VB- Non-isolated supply voltage for additional use and connection of the buffer capacitors Sense Control input for the optional di/dt or dv/dt control, setting of the soft shut down or active clamping RC A; RC B RC network for VCE sat reference curve www.eupec.com www.EiceDRIVER.com Page 6 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.6 Pin configuration of the 2ED300C17-S 1 VDD 2 VDD 3 VDD 4 Fault 5 Reset 6 CA 7 IN B 8 CB 9 Modus 10 Fault 11 IN A 12 GND 13 GND 14 VDC 15 VDC 16 VDC 17 VDC 18 VDC 19 GND 20 GND 21 GND 22 GND 23 GND Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC A 38 Vce sat A 37 E. A 36 Emitter Sense Collector Csup Gate RSSD CSA RSA 2ED300C17-S Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sence B 27 RC B 26 Vce sat B 25 E. B 24 Emitter Sense Collector Csup Gate RSSD CSB RSB Figure 1.6 Pin configuration of the 2ED300C17-S Pin Label Function Pin Label Function 1 VDD +15V for electronics primary 2 VDD 3 VDD +15V for electronics primary 45 Gate A Gate channel A +15V for electronics primary 44 Gate A Gate channel A 4 5 Fault Fault output 43 COM A Reference point A Reset Logic level to reset channel A and B 42 COM A Reference point A 6 CA Delay time ch. A “half bridge mode“ 41 VA+ +16V External buffer capacitor 7 IN B PWM input B 40 VA- -16V External buffer capacitor 8 CB Delay time ch. B “half bridge mode“ 39 Sense SSD / clamping input 9 Mode Mode selection 38 RC Reference RC network channel A 10 Fault Fault output 37 VCE sat Collector sense channel A 11 IN A PWM input A 36 E. A External fault input channel A 12 GND Ground for electronics primary 35 Physically non existent 13 GND Ground for electronics primary 34 Physically non existent 14 VDC +15V for SMPS 33 Gate B Gate channel B 15 VDC +15V for SMPS 32 Gate B Gate channel B 16 VDC +15V for SMPS 31 COM B Reference point B 17 VDC +15V for SMPS 30 COM B Reference point B 18 VDC +15V for SMPS 29 VB+ +16V External buffer capacitor 19 GND Ground for SMPS 28 VB- -16V External buffer capacitor 20 GND Ground for SMPS 27 Sense active- clamping / SSD 21 GND Ground for SMPS 26 RC Reference RC network channel B 22 GND Ground for SMPS 25 VCE sat Collector sense channel B 23 GND Ground for SMPS 24 E. B External fault input channel B www.eupec.com www.EiceDRIVER.com Page 7 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.7 Maximum permissible values Supply voltage VDC Maximum primary supply voltage +16 V PWM signal input voltage Vin Max. voltage on inputs IN A; IN B ±20 V Logic signal input voltage ViH Max. voltage (Mode; Reset) ±20 V Logic signal output current IOC Fault output; max. continuous current open collector 20 mA Peak output current ON IG on Max. driver peak output current +30 A Peak output current OFF IG off Max. driver peak output current -30 A Output current summed maximum |Iout| AV Average value of the summed output current values per channel 1) 133 mA Maximum output power PDC/DC PDC/DC channelA + channel B 8 W Maximum IGBT voltage VCES Maximum collector-emitter voltage on IGBT 1700 V Isolation test voltage Visol IO Input- Output (RMS, 50Hz, 1s) 5000 V~ Isolation test voltage Visol 12 Input A- Output B (RMS, 50Hz,1s) 2250 V~ Surge voltage test Visol Su Surge test according to EN50178 Input to Output 9600 V Gate resistor Rg min Min. gate resistor (module internal + external gate resistor) 1 Ω Gate capacity Cies max Maximum IGBT gate capacity 350 nF dv/dt Voltage slew rate secondary to primary site 50* kV/ µs Top Operating temperature 2ED300C17-S -25......+85 °C Top Operating temperature 2ED300C17-ST -40 .....+85 °C Tsto. Storage temperature -40 .....+85 °C fs max switching frequency Max. switching frequency(Top<65°C PDC/DC=8W) 60’000 Hz Supply current IDC max. Maximum continue permissible current draw of the dual driver 533 mA tTD min min. interlock delay time Factory set delay time in half-bridge mode 1,6 µs d Maximum duty cycle 100 % duty cycle * during test • 133mA refer to gate input and additive ancillary voltage (see chapter 2.10) |Iout| AV = |IG |AV+Iout www.eupec.com www.EiceDRIVER.com Page 8 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.8 Characteristic values All values at +25°C Min. Typ. Max. VDC supply voltage primary DC-DC +14 +15 +16 IDC current draw DC-DC +15V 80 IDC current consumption DC-DC (VDC=+15V PDC/DC=8W) mA 8 VDD supply voltage electronics +14 IDD current draw electronics +15 +16 W +15V 60 0 V mA 8 switching frequency V 525 PDC-DC power DC-DC SMPS fS Recommend. kHz Tpd on signal transition time switch on 670 ns Tpd off signal transition time switch off 580 ns tdif transition time differences 50 ns tmd Minimal puls suppression 400 ns d duty cycle 100 0 Reference voltage for the VCE sat – monitoring VCEstat 2 Threshold logic and signal level (IN A/B; Reset; Mode) VLevel 9 +8 Reactivation after fault condition and IN A/B Low2) tBK 50 Interlock delay time in half-bridge mode tTD4) 1,6 % 83) V +15 V 60 ms µs Coupling capacity primary/secondary Cps 18 pF Coupling capacity sec. channel A to B Css 15 pF 1) “Conditions to be defined“ chapter 2.4 3) See chapter 2.7 4) See chapter 2.3 5) See chapter 2.6 2) See Max. switching frequency: www.eupec.com I (mA) f S max . = outAV QG ( µC ) ⋅1,5 fmax= maximum switching frequency IoutAV= average cont. output current per channel QG= maximum IGBT gate charge at 30V 1.5= tolerance factor www.EiceDRIVER.com Page 9 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.9 Maximum switching frequency with different module nominal currents IGBT3 1200V IGBT3 All values by +25°C 4 * Target values 3,5 3 Drive power in W 2,5 2 150A 225A 1,5 300A 450A 1 600A 800A 0,5 1200A 1600A 0 0 5000 10000 15000 20000 25000 30000 Switching frequency in Hz 1700V IGBT3 All values by +25°C 4 * Target values 3,5 Drive power in W 3 2,5 2 150A 225A 1,5 300A 450A 1 600A 800A 0,5 1200A 1600A 0 0 5000 10000 15000 20000 25000 Switching frequency in Hz www.eupec.com www.EiceDRIVER.com Page 10 30000 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 1.10 Mechanical dimensions 2.95mm RM2.54mm RM2.54mm 2.95mm 24 45 28mm 72 mm 27 mm 1 60,5 mm 23 RM2.54mm 2.31mm 2.31mm Clearance distance and creep page Primary/ Secondary >15 mm Clearance distance Secondary/ Secondary >6 mm Creep page Secondary/ Secondary >14 mm Max.25mm 20mm d=1mm www.eupec.com www.EiceDRIVER.com Page 11 PCB d=1mm Technical Information EiceDRIVER™ 2ED300C17-S preliminary 2. The transformer 2.1 Safe electrical isolation Protection Class II according to EN50178 The safe isolation between primary and secondary side of the two transformers and the switch mode power supply is the basis for the 2ED300C17-S. Highly insulated coil wires, core insulated ferrites and a special sealing compound (UL94 V-0) are used for this purpose. The design makes sure that all windings are physically separated from each other. There are no overlapping primary and secondary windings. The winding connections are terminated directly to the pins which are cast into the housing. All that is contained in a plastic housing certified to UL 94. 9 16 8 1 Figure 2.1 Complete transformers with cores in position The transformer is designed for use in industrial and traction applications. The test voltage applied between all inputs and all outputs is 5kV AC for 1 second. The test voltage applied between the secondaries is 2.25kV AC for 1 second. (EN50178 Table18) (Individual test) The insulation test is completed by the surge voltage test stipulated by EN50178. Surge voltage test according to (EN50178 table 17) is 1.5/50µs with 9.6kV. The partial discharge extinction voltage stipulated by the standard (EN50178 table19) is above 1763V crest value (type test). www.eupec.com www.EiceDRIVER.com Page 12 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3 Application of the 2ED300C17-S: 3.1 Power supply The 2ED300C17-S has an integrated DC-DC switch mode inverter, which generates the required secondary voltages. The generated voltages are for the top and bottom channel with +15V primaries each ±16V secondaries. Hence the 2ED300C17-S only requires one external power supply of +15V. The 2ED300C17-S is operated on a stabilized +15V (±1V) supply. It is distinguished between VDD and VDC. All inputs are switched with+15V,where VDC should be additionally stabilized by a capacitor CDC (see figure 3.1). This stabilizing capacitor CDC should be 220µF minimal. All GND pins have to be connected. To prevent a ground loop there is no internal connection of the DC-DC SMPS ground and the primary electronics. 10R 1µF +15V CDC 1 VDD +15V 2 VDD +15V 3 VDD +15V 4 Fault A 5 Reset 6 CA 7 IN B 8 CB 9 Modus 10 Fault B 11 IN A 12 GND 13 GND 14 VDC +15V 15 VDC +15V 16 VDC +15V 17 VDC +15V 18 VDC +15V 19 GND 20 GND 21 GND 22 GND 23 GND Note! If the driver is turned on with +15V, a low voltage fault may be tripped depending on the voltage slew rate. This will be reset after 50ms if both signal levels IN A and IN B remain Low during this time. Note! No potential difference greater than 20V may occur between VDD and VDC. Figure 3.1 Pin configuration of +15V voltage supply Note! The 2ED300C17-S features secondary under-voltage monitoring. If the secondary supply voltage drops below typical +12V or -12V, a fault condition will occur which turns off the driver and is transferred to the primary as well. www.eupec.com www.EiceDRIVER.com Page 13 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.2 Mode selection The 2ED300C17-S features two operating functions to drive eupec IGBT modules. These are the direct mode and the half-bridge mode. • The direct mode: In this mode there is no link between the two channels of the 2ED300C17-S. Both channels IN A and IN B are working independently from each other and may both be turned on at once. The inputs IN A and IN B are switched with +15V PWM signals. The direct mode is activated by taking pin 9 ”Mode selection” to GND (e.g.: pin 12/13). The inputs CA pin 6 and CB pin 8 are not connected. Note! In the direct mode the inputs CA and CB may not be connected to +15V or GND. For EMC reasons it is recommended to connect the inputs CA and CB with 470pF to GND. • The half-bridge mode: This mode generates an interlock time between the two channels of the 2ED300C17-S. I.e. there is always only one channel active. The interlock time between the switching events may be selected. This is done with the inputs CA pin 6 and CB pin 8. The half-bridge mode is activated by taking pin 9 ”Mode selection” to VDD (pin 1/2/3). The inputs IN A and IN B are switched with PWM inputs. Explanation: There is always only one channel turned on. If there is a high signal on one channel, this is turned on after the interlock time has ended. If during this time there is a high signal for the second channel it will be ignored until the first turned on channel has turned off. PWM IN A +15V 0V PWM IN B +15V 0V Gate A +15V -15V Gate B +15V -15V Figure 3.2 Switching diagram with interlock delay times www.eupec.com www.EiceDRIVER.com Page 14 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.3 Interlock delay times In half-bridge mode the 2ED300C17-S generates a minimal internal interlock delay time between the two channels. This minimal interlock time tTD is preset to 1,6 µs. By adding a capacitance to the two inputs CA and CB this interlock time is extended and adapted to the requirements of the application. The capacitance is externally added between CA and CB to GND (see page 7 – 1.6 Pin configuration). The capacitance for the required interlock time is derived from the following table: Del. time TTD CA / CB 1,6µs n.c. 2µs 47pF 2,4µs 100pF 3.4µs 220pF 4,3µs 330pF 5,4µs 470pF 9,6µs 1nF NOTE ! It is not permit to connect the inputs CA and CB direct to a voltage potential. NOTE ! The tolerance of the interlock delay times depends mainly on the tolerance of the external capacities. This needs to be considered when choosing the capacitors! Table 3.3 Interlock delay time settings Pin 6 CA Pin 8 CB Ca Cb Primary Side Secondary Side A Pulse Transformer DC/DC Pin 12 GND Pin 13 GND Secondary Side B Figure 3.3 Connection of the external capacitors to increase the interlock times www.eupec.com www.EiceDRIVER.com Page 15 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.4 Logic level The term “logic level” concerns the fault output and the reset input as well as the input for operating mode selection described in chapter 3.2. • Logic inputs The two inputs (reset and mode) may be stressed with a maximum voltage of 20V. The switching threshold is at 8V, so the existing +15V offers itself as switching signal. 1) Mode: see chapter 3.2 2) Reset: The driver can be reset via the reset input after a fault has been indicated. The reset input is active high, i.e. a high signal activates the reset. Logic signal level is by 8V. If reset is used by the PWM inputs IN A and IN B, the reset input is inactive and pin 5 (Reset) has to be permanently connected to GND If both PWM signals are “low” for more than 39ms the driver is reset. • Logic outputs The driver core recognizes short circuit current faults of the IGBTs and faults of the supply voltage. Additionally the 2ED300C17-S features an external fault input. If a fault is detected through the VCE sat monitoring, an under-voltage or the external fault input, the driver core is immediately turned off. With these faults on the secondary side, the IGBT is shut down via a soft turn-off. Each fault is stored until a reset signal on Pin 5 is present. The reset is also activated when the input signal on both channels is low for more than 39ms. Indication of a fault occurs in any case via a common fault line on the logic output FAULT. The fault is brought out twice via Pin4 and Pin10. These outputs are configured as open collector. The outputs can operate at up to 20V and can switch a maximum of 20mA . If a fault is recognized the internal transistor switches and pulls the fault output to GND. +15V +15V 1 VDD +15V 2 VDD +15V 3 VDD +15V 4 Fault 5 Reset 6 CA 7 IN B 8 CB 9 Modus 10 Fault 11 IN A GND Figure 3.4 Fault output Note! The fault outputs are internally connected. There is only one fault output - doubled up. www.eupec.com www.EiceDRIVER.com Page 16 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.5 Signal level In both the direct mode and the half-bridge mode the input IN A of the 2ED300C17-S controls channel A, and input IN B controls channel B. The inputs feature a SchmittTrigger and an active high logic. A high level turns the IGBT on and a low level turns it off. The two signal inputs may be operated with a maximum of 20V per channel. Brief negative peaks of equal voltage will not lead to damage of the inputs. The switching threshold is at +8V to GND. The input impedance is 3.3kOhm for each channel. For long cables it may be necessary to connect an external burst suppression network. Note: The 2ED300C17-S features a minimal pulse suppression. Pulses with less than 400ms will be suppressed by the driver. 1 VDD +15V 2 VDD +15V 3 VDD +15V 4 Fault 5 Reset 6 CA 7 IN B 8 CB 9 Modus 10 Fault 11 IN A 12 GND 13 GND 14 Vdc +15V 10µH PWM B 10µH PWM A 3.6 IGBT connection Figure 3.5 Input signal level The 2ED300C17-S features two independent channels to drive the IGBTs. It is possible to drive individual IGBTs, single IGBT-modules or IGBT-modules connected in parallel. The maximum size of the IGBT-modules depends mainly on the IGBT input capacitance and on the switching frequency. This dependency is described on page 9 for KE3 modules. When considering the gate currents, note that these are not determined by the external gate resistors alone. Many eupec IGBT modules have internal gate resistors (See chapter 5). Additionally, the 2ED300C17-S features a low output impedance. Hence a gate current calculated via the external gate resistor will never be realized in practice. An approximation for the drive power and peak current can be achieved with: •Driver power P G = f ⋅ ∆ V GE 2 ⋅C ies ⋅3 P = P DD + PG • Max. driver current www.eupec.com IG max = ∆ V GE R G (min) www.EiceDRIVER.com f = switching frequency Cies = input capacity (datasheet) PDD = driver dissipation ∆ V = 30 V at ± 15 V RG(min)=RG extern+RG intern Page 17 Technical Information EiceDRIVER™ 2ED300C17-S preliminary •Gate connection The gate of the IGBT is connected to Gate A or Gate B via the external gate resistor. The associated auxiliary emitter is connected directly to the COM outputs. The gate output voltage is ±15V with respect to COM A and COM B (considering chapter 3.1). By utilizing the external gate resistors it is possible to realize turn-on and turn-off with different gate resistances. Additionally to the gate resistor a gate-emitter resistor and gate clamping should be used. These would be placed between the gate and the aux. emitter. As RGE a resistor <10kOhm is recommended. The gate clamping is done with Zener diodes or suppressor diodes with a break-over voltage of less than 18V. These diodes prevent the gate voltage to rise to inadmissible levels through parasitic effects (e.g. Miller capacity). The external gate resistors are defined in the eupec IGBT datasheet. RGA Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC A 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC B 26 Vce sat B 25 E. B 24 RGE RGB RGE Figure 3.61 Gate connection Note! The use of different gate resistors for turn-on and turn-off with field stop IGBTs to change the di/dt (KE3 modules) is not necessary. With field stop IGBTs only the di/dt turn-on behavior is influenced by the gate resistor. See chapter 3.10 ”sense”. The dv/dt for turn-on and turn-off is still set with the gate resistor. RG ein RG aus Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 RGE Figure 3.62 Gate connection with RG on and RG off www.eupec.com www.EiceDRIVER.com Page 18 Technical Information EiceDRIVER™ 2ED300C17-S preliminary •Collector connection The 2ED300C17-S is able to measure and evaluate the voltage between collector and emitter of an IGBT. This is used to recognize a short circuit and then shut-down. For the optional function of DVRC or active clamping the connection to the collector is also required. For the short circuit shut-down function the auxiliary collector is connected to VCEsat A or VCEsat B. To block the high DC-link voltage during shut-down a diode Dx with high reverse blocking voltage has to be connected between the collector and the “Vce sat“ input. The reverse blocking capability of these diodes should be higher than the IGBTmodule voltage (1200V/1700V). Further the diode has to follow the switching frequency and therefore has to be accordingly fast. Two or three diodes in series is an option to achieve the required blocking capability. Application and adjustment of the short circuit shut-down is described in detail in the next chapter 3.7. DA 2x UF4007 RGA Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 RGE 1nF DB 2x UF4007 470R RGB RGE 1nF 470R Figure 3.63 Collector connection for V measurement ce sat Note! The RGE, the gate-emitter clamping diodes, the gate resistor and the collector diodes DX should be placed in the closest possible vicinity of the module. Note! If wire links are used between the drivers and the IGBTs the gate lead should be twisted together with the respective emitter and collector leads. Where these connections should be as short as possible. Lengths of more than 20cm are to be avoided. www.eupec.com www.EiceDRIVER.com Page 19 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.7 IGBT short circuit and over-current shut-down with SSD “soft shut down“ A short circuit or over-current is detected by the integrated VCE measurement in the 2ED300C17-S (see chapter 3.6). The 2ED300C17-S measures the VCE voltage while the IGBT is turned on. If the VCE rises above the preset reference voltage during this period, a fault is triggered and the IGBT is turned off via the internal soft shut-down. For eupec IGBT-modules with NPT and FS-technology the soft shut-down reduces the voltage over-shoot by a slower turn-off. •The reference curve is only adjustable via an external RSX and CSX . With RSX the reference voltage is set and with CSX the reference time. The resistor and the capacitor are connected between RC A and COM A or RC B and COM B . The reference time elapses directly with the turn-on of the respective driver side (See figure 3.7.2) V Vref Reference curve Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 CSA RSA Vref=f(RSX) Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 CSB PWM RSB t Vref=f(CSX) t Figure 3.7.2 Reverence curve Figure 3.7.1 RSX and CSX connection to adjust the reference curve Reference Voltage Vref CSX= 0 pF CSX= 100 pF CSX= 220 pF CSX= 470 pF CSX= 1 nF 7 2V RSX= 2 kΩ 0,5µs 1,5 µs 3 µs 5 µs 4V RSX= 5,4 kΩ 1 µs 3 µs 4 µs 9 µs 6V RSX= 12 kΩ 1 µs 4 µs 6 µs 8V RSX= 32 kΩ 1 µs 5 µs 7 µs 9V RSX= 70 kΩ 1 µs 5 µs 7 µs Table 3.7 gives reference voltage Vref and reference time tref until the reference voltage is reached. www.eupec.com www.EiceDRIVER.com Page 20 Technical Information EiceDRIVER™ 2ED300C17-S preliminary A comparator inside the 2ED300C17-S compares the voltage at the VCE sat input with the reference voltage Vref. The maximum VCE voltage at the comparator will be 10V. With the turn-on of the IGBT the VCE voltage drops to its threshold value depending on the load current IC. To suppress commutation effects during turning on the IGBT there is the settable reference curve Vref. This drops, depending on the external CSX and RSX network, from 16V to the set voltage level. If the VCE voltage rises above the reference voltage at any time, a fault is tripped and the driver is locked. The various different operating conditions are depicted in the four cases below. If the fault occurs, the IGBT is turned off via the SSD (Soft Shut Down) function. +15V +15V Fault +10V +10V Vref Vref +5V +5V VCE VCE 0V 0V Case 2. IGBT turns on too slowly or reference time is too short Case 1. Usual case +15V +15V Fault +10V VCE Fault VCE +10V Vref Vref +5V +5V 0V 0V Case 3. Short circuit during operation Case 4. Short circuit during turn-on Figure 3.7.3 Different faults depicted www.eupec.com www.EiceDRIVER.com Page 21 Technical Information EiceDRIVER™ 2ED300C17-S preliminary • Trigger suppression for the Vce sat measurement To vary the sensitivity of the VCE , the 2ED300C17-S uses an RC timing network. This network is used to set the sensitivity of the VCE SAT monitoring as required by the individual application. One has to keep in mind that this RC network is a timing function. Accordingly, reaching the reference voltage and in this connection the detection of the temporal short circuit current in the IGBT depend on the charging process of the CVCE capacitor. This can easily be defined by measuring in front of CVCE once and in comparison to this V ce sat x directly at the input. The RC combination is able to prolong the operating time till the IGBT switches off in case of a short circuit. This is to say that in addition to reference time treff (table 3.7) and SSD cycle time tSD=5µs and system cycle time tSD=1µs, the trigger suppression time has to be taken into account. As a standard, a value of RVCE =470R and CVCE =1nF is recommended. Should the VCE sat monitoring react too sensitively the CVCE value can be increased. This of course prolongs the trigger time of the short circuit turn-off. In a contrary case, it is certainly recommended to decrease the CVCE value or the RVCE value. One always has to make sure that the short circuit across the IGBT is switched off after 10µs. DA 2x UF4007 RGA Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 RGE CVCE 1nF RVCE 470R DB 2x UF4007 RGB RGE CVCE 1nF RVCE 470R Figure 3.7.4 Trigger suppression of the Vce sat measurement www.eupec.com www.EiceDRIVER.com Page 22 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.8 SSD “Soft Shut Down“ The SSD “Soft Shut Down“ is used to softly shut down the IGBT if a fault occurs. This is sensible in order to avoid destruction of the IGBT due to high voltage overshoots during turn-off. If set correctly the SSD will reduce the turn-off di/dt of all eupec IGBT products and hence the voltage overshoot during fault conditions. The “Soft Shut Down“ is set with resistor RSSD. This resistor is externally connected between Sense and –16V (see figure 3.8.1). Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC A 38 Vce sat A 37 E. A 36 RSSD CSA RSA CSA RSA 2ED300C17-S Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sence B 27 RC B 26 Vce sat B 25 E. B 24 RSSD Figure 3.8.1 Connection of RSSD The “Soft Shut Down“ has to be adapted to the IGBT type used. Since the turn-off behavior and the resulting voltage overshoot depends on the IGBT type and the construction of the entire application, the resistance of the RSSD resistor has to be found in a practical manner. As guidance one can use the module FS450R17KE3 with an RSSD = 10kΩ. IGBT modules with a greater input capacitance Cies will need a lower RSSD value, IGBT modules with a lower input capacitance Cies will need a greater RSSD value. The dissipation of the resistor is calculated as follows: PSSD [W ] = 1024 RSSD If a fault is recognized and the “Soft shut down“ is activated, the capacitances of the internal bipolar- output stage go through the charge reversal and thus the IGBT input capacitance Cies and the Miller capacitance Cres are discharged slowly. This process is limited to tSD= 4µs. After this time the output of 2ED300C17-S turns off hard. The driver has to be reactivated by a “Reset“ (see chapter 3.4 logic levels). www.eupec.com www.EiceDRIVER.com Page 23 Technical Information EiceDRIVER™ 2ED300C17-S preliminary Note! The “Soft Shut Down“ may slightly increase the VGE. Hence the gate clamping described in chapter 3.6 IGBT Connection has to be observed. Note! eupec IGBT modules are generally designed for short circuits of up to tP≤ 10µs. With the calculation of the external network RSX and CSX make sure not to exceed this time. tP-tSD-tsys= tref tP= short circuit time IGBT 10µs tSD= SSD transition time 5µs tsys= system transition time 1µs tref= reference time (+ Trigger suppression for the Vce sat ) Note! The “Soft Shut Down” is not 100% protection from voltage overshoots during fault turnoff! Should a short circuit occur and at the same time the natural PWM puls go to Low Level the SSD can not be commenced. This case is rare but can occur. Active Clamping will then protect against over-voltage (see 3.10). VGE 1100V IC VCE VµC Figure 3.8.2: Short circuit turn-off at 1100V with SSD The short circuit turn-off depicted in Fig. 3.8.2 clearly shows the course of the Gate-Emitter voltage with SSD. www.eupec.com www.EiceDRIVER.com Page 24 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.9 External fault input The 2ED300C17-S features an external fault input E.A and E.B. These are used to set the internal fault memory by a high gate output signal and to trigger a fault. The fault inputs E.A and E.B have an active high logic. Switching level is at 5V, so that a high signal will trigger a fault. The maximum level for the input is VA+ or VB+ referenced to the adjoining COM. This input is considered for example to detect an over-temperature and/or over-current and so to shut down the driver. Note that the inputs E.A and E.B may rise up to DClink potential! Note ! If the inputs E.A and/or E.B are not used, they have to be connected to COM A / COM B. 3.10 “Sense“ input (SSD “Soft Shut Down“, optional DVRC or active clamping) A special feature of the 2ED300C17-S is the ability to directly manipulate the driver output stage. This is a bipolar output stage externally accessible via the ”Sense” input. This is necessary to limit the voltage overshoot through the di/dt during turn-off of the IGBTs. (see also chapter 3.8 SSD). With a additional circuit and by using the sense input it is possible to control this di/dt in every operating point during turn-off of the IGBT and hence prevents inadmissibly high turn-off voltage overshoots. RGA Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 RGE RGB RGE Figure 3.10.1 Utilization of the ”Sense” input www.eupec.com www.EiceDRIVER.com Page 25 Technical Information EiceDRIVER™ 2ED300C17-S preliminary A further application of the ”Sense” input is the use of an active clamping** with direct feedback to the output stage. In this case the Zener diodes used are only minimally loaded which makes for example transile diodes possible.. This can then be combined with an active clamping directly to the gate. SM6T220A ** not yet tested with all IGBT modules! RGA Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 RGE SM6T220A RGB RGE Figure 3.10.2 Utilization of the “Sense“ input with active clamping The standard application with the 2ED300C17-S is the “Soft Shut Down“. This is a quasilinear turn-off during fault condition.. The “Soft Shut Down“ has to be adapted to each module type. For this an external resistor RSSD is connected between “Sense“ and –16V. (See chapter 2.8 Short circuit/over-current turn-off with “Soft shut down“ ) Note! The “Soft shut down“ is the standard setting of the 2ED300C17-S. For this a resistor RSSD should be connected between “Sense and –16V. If active clamping is used the RSSD can also be utilized. www.eupec.com www.EiceDRIVER.com Page 26 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 3.11 Additional output voltage / buffer capacitors Depending on the utilization of the internal DC-DC SMPS an additional use of the secondary supply voltage is possible. This is made available on the outputs +16V and – 16V and is referenced to the respective COM. This voltage is potential separated to the primary side. The ground COM is here referenced to the emitter of the respective IGBT. The outputs +16V and –16V are also used to connect buffer capacitors Csup. These prevent voltage drops with high pulse currents. The buffer capacitors should be placed in closest vicinity to the 2ED300C17-S and must always be used. RGA Gate A 45 Gate A 44 COM A 43 COM A 42 +16V 41 -16V 40 Sense A 39 RC B 38 Vce sat A 37 E. A 36 Gate B 33 Gate B 32 COM B 31 COM B 30 +16V 29 -16V 28 Sense B 27 RC A 26 Vce sat B 25 E. B 24 Csup RGE RGB RGE Csup Figure 3.11 2ED300C17-S with external buffer capacitors Note! The additional electrolytics Csup always have to be connected. When selecting these capacitors take note of the high ripple current requirement. Meaning, only caps with low impedance are to be used. www.eupec.com www.EiceDRIVER.com Page 27 Technical Information 10µH Fault A/B Reset PWM B 10µH 100nF PWM A +15V 1µF 2k2 10R 470µF Gate B 33 Gate B 32 COM B 31 COM B 30 VB+ 29 VB- 28 Sense B 27 RC B 26 Vce sat B 25 E. B 24 2ED300C17-S Gate A 45 Gate A 44 COM A 43 COM A 42 VA+ 41 VA- 40 Sense A 39 RC A 38 Vce sat A 37 E. A 36 220µF 1nF 470R 560pF 220µF 1nF 470R 560pF SM6T220A RSSD 10K SM6T220A 12K RSSD 10K 220µF 12K 220µF 3.12 Application example 2ED300C17-S 1 +15V 2 +15V 3 +15V 4 Fault 5 Reset 470pF 6 CA 7 IN B 8 CB 9 Modus 10 Fault 11 IN A 12 GND 13 GND 14 +15V 15 +15V 16 +15V 17 +15V 18 +15V 19 GND 20 GND 21 GND 22 GND 23 GND Fig. 3.12 Commissioning circuit in the direct mode: (Both channels can be switched independently) 2x UF4007 1,5KE18 RGate 10k 2x UF4007 RGate 10k 1,5KE18 Page 28 www.EiceDRIVER.com www.eupec.com preliminary EiceDRIVER™ 2ED300C17-S Technical Information EiceDRIVER™ 2ED300C17-S preliminary 4.1 Designations and symbols Cps CSS Csup Cies Cies max CSX CVCE COM d DVRC DOCD dv/dt di/dt EDFA fS fS max IC IDC IDD IG IG on IG off I0 IOC Iout |IG| AV |Iout| AV IDC max PDC/DC PSSD PDD PG QG Rg Rg min Rg intern Rg extern RGE RSSD coupling capacity primary/secondary coupling capacity sec. channel A to B buffer capacitor IGBT input capacity max. admissible IGBT- Gate- capacity reference capacitor for time setting VCE sat trigger suppression reference point duty cycle Dynamic Voltage Rise Control dynamic over-current detection voltage slew rate current rise time logic external fault input switching frequency max. admissible switching frequency IGBT collector current current draw DC-DC current draw electronics output peak current output peak current “On“ output peak current “Off“ Quiescent current logic signal output current output current of VA;B± summed average gate current summed average output current maximum primary current draw peak output power power of the SSD resistor driver power dissipation maximum gate power dissipation Max.IGBT gate charge at 15V Gate resistor Minimum gate resistor IGBT Chip internal gate resistor IGBT external gate resistor (Datasheet) Gate- Emitter resistor Soft Shut Down resistor www.eupec.com RSX RVCE SSD tTD tTD min tBK tdif tmd tP tref tsd tsys tpd Top Tstg VLevel VDD VDC ViH ViHS Vin Visol Visol IO Visol 12 Visol Su VCE VCE sat VCE stat Vref VGE VA;B+ VA;B- Reference resistor voltage setting VCE sat trigger suppression Soft Shut Down interlock delay time minimum interlock delay time reactivating time transition time difference minimal pulse suppression short circuit time reference time DOCD transition time SSD system transition times signal transition time operating temperature storage temperature logic switching level supply voltage electronics primary primary DC/DC supply voltage maximum voltage of the logic levels switching threshold logic signals signal input voltage isolation test voltage isolation test input- output isolation test output A- output B surge test voltage input- output IGBT collector- emitter voltage IGBT saturation voltage VCE sat monitoring reference voltage reference voltage of the DOCD Gate- Emitter voltage secondary positive voltage secondary negative voltage www.EiceDRIVER.com Page 29 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 4.2 Internal module gate resistor RG intern FP10R12KE3 FP15R12KE3 FP25R12KE3 FP40R12KE3 FP50R12KE3 FP75R12KE3 FS25R12KE3 FS35R12KE3 FS50R12KE3 FS75R12KE3 FS100R12KE3 FS150R12KE3 FS150R12KE3 G FS225R12KE3 FS300R12KE3 FS450R12KE3 0 Ohm 0 Ohm 8 Ohm 6 Ohm 4 Ohm 10 Ohm 8 Ohm 6 Ohm 4 Ohm 10 Ohm 7.5 Ohm 5 Ohm 1.33Ohm 3.33 Ohm 2.5 Ohm 1.66 Ohm FF150R12KE3 G FF200R12KE3 FF300R12KE3 FD200R12KE3 FD300R12KE3 DF200R12KE3 DF300R12KE3 FZ300R12KE3 FZ400R12KE3 FZ600R12KE3 FF600R12KE3 FF800R12KE3 FF1200R12KE3 FZ1200R12KE3 FZ1600R12KE3 FZ2400R12KE3 FZ3600R12KE3 5 Ohm 3.75 Ohm 2.5 Ohm 3.75 Ohm 2.5 Ohm 3.75 Ohm 2.5 Ohm 2.5 Ohm 1.875 Ohm 1.25 Ohm 1.25 Ohm 0.94 Ohm 0.62 Ohm 0.62 Ohm 0.46 Ohm 0.3 Ohm 0.2 Ohm Table 4.2.1 RG intern KE3 1200V modules FS150R17KE3G FS225R17KE3 FS300R17KE3 FS450R17KE3 FF200R17KE3ENG FF300R17KE3ENG FZ400R17KE3ENG FZ600R17KE3ENG 3.17 Ohm 2.83 Ohm 2.5 Ohm 1.67 Ohm 2.375 Ohm 2.13 Ohm 1.19 Ohm 1.06 Ohm Table 4.2.2 RG intern KE3 1700V modules www.eupec.com www.EiceDRIVER.com Page 30 Technical Information EiceDRIVER™ 2ED300C17-S BSM50GD120DN2G FS75R12KS4 BSM75GD120DLC BSM75GD120DN2 BSM100GD120DN2 BSM100GD120DLC FS100R12KS4 BSM100GT120DN2 BSM150GT120DN2 BSM200GT120DN2 BSM150GT120DLC BSM200GT120DLC BSM100GAL120DN2 BSM150GAL120DN2 BSM200GAL120DN2 BSM100GAR120DN2 BSM150GAR120DN2 BSM200GAR120DN2 5 Ohm 5 Ohm 5 Ohm 5 Ohm 5 Ohm 5 Ohm 5 Ohm 5 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm 1 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm BSM300GAR120DLC BSM150GAL120DLC BSM200GAL120DLC BSM300GAL120DLC 1 Ohm 2,5 Ohm 2,5 Ohm 1 Ohm FF400R12KF4 FF600R12KF4 FF800R12KF4 FF400R12KL4C FF600R12KL4C FF800R12KL4C 0,62 Ohm 0,62 Ohm 0,62 Ohm 0,62 Ohm 0,62 Ohm 0,62 Ohm FZ800R12KS4 FZ800R12KF4 FZ1050R12KF4 0,56 Ohm 0,56 Ohm 0,61 Ohm preliminary BSM200GB120DLC BSM300GB120DLC FF100R12KS4 FF150R12KS4 FF200R12KS4 BSM200GA120DN2 BSM200GA120DN2S BSM300GA120DN2 BSM300GA120DN2S BSM300GA120DN2E3166 BSM400GA120DN2 BSM400GA120DN2S BSM200GA120DLC BSM200GA120DLCS BSM300GA120DLC BSM300GA120DLCS BSM400GA120DLC BSM400GA120DLCS BSM600GA120DLC BSM600GA120DLCS FZ800R12KL4C FZ1200R12KL4C FZ1600R12KL4C FZ1800R12KL4C FZ2400R12KL4C 2,5 Ohm 1 Ohm 2,5 Ohm 2,5 Ohm 2,5 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 1,25 Ohm 0.5 Ohm 0.5 Ohm 0,31 Ohm 0,31 Ohm 0,31 Ohm 0,21 Ohm 0,21 Ohm FS300R12KF4 FS400R12KF4 FD400R12KF4 FD600R12KF4 F4-400R12KF4 F4-400R12KS4_B2 1,25 Ohm FZ1200R17KF6C_B2 FZ1600R17KF6_B2 FZ1600R17KF6C_B2 FZ1800R17KF6_B2 FZ2400R17KF6C_B2 FD600R17KF6_B2 FD600R17KF6C_B2 FD800R17KF6_B2 0,76 Ohm 0,62 Ohm 0,62 Ohm 0,67 Ohm 0,67 Ohm 1,53 Ohm 1,53 Ohm 0,76 Ohm 1,25 Ohm 0,63 Ohm 1,25 Ohm 1,25 Ohm Table 4.2.3 RG intern 1200V Modul FF400R17KF6C_B2 FF600R17KF6_B2 FF800R17KF6C_B2 FZ800R17KF6C_B2 FZ1200R17KF6_B2 1,53 Ohm 1,53 Ohm 1,25 Ohm 0,76 Ohm 0,76 Ohm Table 4.2.4 RG intern 1700V Modul www.eupec.com www.EiceDRIVER.com Page 31 Technical Information EiceDRIVER™ 2ED300C17-S preliminary 4.3 Type designation EiceDRIVER™ For example: eupec IGBT controlled efficiency DRIVER 2ED300C17-S Isolation class: F = funktion isolation S = safety isolation ST= safety isolation/ Traction Voltage class: 06 = 600V 12 = 1200V 17 = 1700V und 1200V 33 = 3300V 65 = 6500V Driver type: C = Driver core with DC/DC E = Evaluation board I = Driver IC (Coreless Transformer) L = Driver IC (Level shifter) Maximum output current: For example 004 = 0.4 A 020 = 2.0 A 300 = 30.0 A eupec IGBT driver Driver channels 1 = single driver 2 = halfbride driver 6 = SixPACK driver www.eupec.com www.EiceDRIVER.com Page 32