SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FEBRUARY 2009 GENERAL DESCRIPTION The SP26LV431 is a quad differential line driver that meets the specifications of the EIA standard RS-422 serial protocol. The SP26LV431 features Exar's BiCMOS process allowing low power operational characteristics of CMOS technology while meeting all of the demands of the RS-422 serial protocol over 60Mbps under load. The RS-422 protocol allows up to 10 receivers to be connected to a multipoint bus transmission line. The SP26LV431 features a driver enable control common to all four drivers that places the output pins in a high impedance state. Since the cabling can be as long as 4,000 feet, the RS-422 drivers of the SP26LV431 are equipped with a wide common-mode output voltage range to accommodate ground potential differences. REV. 1.1.0 FEATURES • Quad Differential Line Drivers • Compatible with the EIA standard for RS-422 serial protocol • High-Z Output Control • At Least 60Mbps Transmission Rates • 11ns Typical Driver Propagation Delays • Less than 1ns Typical Output Skew • Single +3.3V Supply Operation • Common Driver Enable Control • Compatibility with the industry standard 26LV31 • Ideal For Use with SP26LV432, Quad Receivers FIGURE 1. TYPICAL APPLICATION CIRCUIT Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 FIGURE 2. PIN OUT ASSIGNMENT ORDERING INFORMATION PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE DEVICE STATUS SP26LV431CP-L 16-pin Plastic DIP 0°C to +70°C Active SP26LV431CN-L 16-pin Narrow SOIC 0°C to +70°C Active SP26LV431CN-L/TR 16-pin Narrow SOIC 0°C to +70°C Active SP26LV431EN-L 16-pin Narrow SOIC -40°C to +85°C Active SP26LV431EN-L/TR 16-pin Narrow SOIC -40°C to +85°C Active 2 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 PIN DESCRIPTIONS Pin Assignments PIN NUMBER PIN NAME TYPE DESCRIPTION 1 DI1 I Driver 1 TTL input. 2 DO1A O Non-inverted driver 1 output. 3 DO1B O Inverted driver 1 output. 4 ENABLE I Driver output enable, active HIGH. 5 DO2B O Inverted driver 2 output. 6 DO2A O Non-inverted driver 2 output. 7 DI2 I Driver 2 TTL input. 8 GND Pwr 9 DI3 I Driver 3 TTL input. 10 DO3A O Non-inverted driver 3 output. 11 DO3B O Inverted driver 3 output. 12 ENABLE I Driver output enable, active LOW. 13 DO4B O Inverted driver 4 output. 14 DO4A O Non-inverted driver 4 output. 15 DI4 I Driver 4 TTL input. 16 VCC Pwr Ground. +3.0V to +3.6V power supply. Pin type: I=Input, O=Output. 3 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections to the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability and cause permanent damage to the device. VCC 0.5V to 7.0V VIN (DC Input Voltage) -1.5V to (VCC + 1.5V) VOUT (DC Output Voltage) -0.5V to 7V IIK, IOK (Clamp Diode Current) ±20mA IOUT (DC Output Current, per pin) ±150mA ICC (DC VCC or GND Current, per pin) ±150mA Storage Temperature Range -65°C to + 150°C Power Dissipation 16-pin PDIP (derate 14.3mW/°C above +70°C) 1150mW Power Dissipation 16-pin NSOIC (derate 13.6mW/°C above +70°C) 1100mW CAUTION: ESD (Electrostatic Discharge) sensitive device. Permanent damage may occur on unconnected devices subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts. Personnel should be properly grounded prior to handling this device. The protective foam should be discharged to the destination socket before devices are removed. ELECTRICAL CHARACTERISTICS UNLESS OTHERWISE NOTED: THE FOLLOWING SPECIFICATIONS APPLY FOR VCC = +3.0V TO +3.6V WITH TA = +25OC AND ALL MIN AND MAX LIMITS APPLY ACROSS THE RECOMMENDED OPERATING TEMPERATURE RANGE. SYMBOL VCC PARAMETERS Supply Voltage VIN or VOUT MIN. TYP. 3.0 DC Input or Output Voltage MAX. UNITS 3.6 V VCC V CONDITIONS Input Electrical Characteristics tr or tf Input Rise or Fall Times VIH HIGH Level Input Voltage VIL LOW Level Input Voltage 3 ns 2.0 V 0.8 V Output Electrical Characteristics V VOH HIGH Level Output Voltage VOL LOW Level Output Voltage VT Differential Output Voltage T – V T VOS V OS –V ICC OS 2.5 2.9 0.2 2.0 0.5 2.7 V VIN = VIH or VIL, IOUT = -20mA V VIN = VIH or VIL, IOUT = 20mA V RL = 100Ω, Note 1 Differential Output Voltage 0.4 V RL = 100Ω, Note 1 Common Mode Output Voltage 3.0 V RL = 100Ω, Note 1 Difference in Common Mode Output 0.4 V RL = 100Ω, Note 1 Quiescent Supply Current 100 uA VIN = VCC or GND, Note 2 4 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 UNLESS OTHERWISE NOTED: THE FOLLOWING SPECIFICATIONS APPLY FOR VCC = +3.0V TO +3.6V WITH TA = +25OC AND ALL MIN AND MAX LIMITS APPLY ACROSS THE RECOMMENDED OPERATING TEMPERATURE RANGE. SYMBOL IOZ PARAMETERS MIN. Tri-state Output Leakage Current TYP. MAX. ±2.0 UNITS uA CONDITIONS VOUT = VCC or GND, ENABLE = VIL, ENABLE = VIH ISC Output Short Circuit Current IOFF IOFF -30 -150 mA VIN = VCC or GND, Notes 1 & 3 Output Leakage Current Power Off 100 uA VCC = 0V, VOUT = 6V, Note 1 Output Leakage Current Power Off -100 uA VCC = 0V, VOUT = -0.25V, Note 1 Switching Characteristics Propagation Delays 11 18 ns Figure 5 tSKEW Skew, SP26LV431C_ 0.8 2 ns Figure 5, Note 4, tSKEW Skew, SP26LV431E_ 3 ns Figure 5, Note 4 10 ns Figure 5 tPLHD, tPHLD tTLH, tTHL Differential Output Rise/Fall Times 4 tPZH Output Enable Time 40 ns Figure 7 tPZL Output Enable Time 40 ns Figure 7 tPHZ Output Disable Time 35 ns Figure 7, Note 5 tPLZ Output Disable Time 35 ns Figure 7, Note 5 CPD Power Dissipation Capacitance 50 pF Note 6 CIN Input Capacitance 6 pF NOTE: 1. Refer to EIA specifications for RS-422 serial protocol for exact test conditions. 2. Measured per input. All other inputs at VCC or GND. 3. This is the current sourced when a high output is shorted to GND. Only one output at a time should be shorted. 4. Skew is defined as the difference in propagation delays between complementary outputs at the 50% input. 5. Output disable time is the delay from ENABLE or ENABLE being switched to the output transistors turning off. The actual disable times are less than indicated due to the delay added by the RC time constant of the load. 6. CPD determines the no load dynamic power consumption, PD = (CPDVCC2f) + (ICCVCC), and the no load dynamic power consumption, IS = (CPDVCCf) + ICC. 5 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 3. SP431 BLOCK DIAGRAM FIGURE 4. AC TEST CIRCUIT 6 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 5. PROPAGATION DELAYS FIGURE 6. DRIVER SINGLE-ENDED TRI-STATE TEST CIRCUIT 7 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 7. DRIVER SINGLE-ENDED TRI-STATE WAVEFORMS FIGURE 8. DIFFERENTIAL RISE AND FALL TIMES 8 REV. 1.1.0 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 1.0 PRODUCT DESCRIPTION The SP26LV431 is a low-power quad differential line driver designed for digital data transmission meeting the specifications of the EIA standard RS-422 serial protocol. The SP26LV431 features Exar's BiCMOS process allowing low power operational characteristics of CMOS technology while meeting all of the demands of the RS-422 serial protocol up to 60Mbps under load in harsh environments. The RS-422 standard is ideal for multi-drop applications and for long-distance communication. The RS-422 protocol allows up to 10 receivers to be connected to a data bus, making it an ideal choice for multi-drop applications. Since the cabling can be as long as 4,000 feet, RS-422 drivers are equipped with a wide common mode output range to accommodate ground potential differences. Because the RS-422 is a differential interface, data is virtually immune to noise in the transmission line. The SP26LV431 accepts TTL or CMOS input levels and translates these to RS-422 output levels. The SP26LV431 features active HIGH and active LOW driver enable controls common to all four driver channels see Table 1. A logic HIGH on the ENABLE pin (pin 4) or a logic LOW on the ENABLE pin (pin 12) will enable the differential driver outputs. A logic LOW on the ENABLE pin (pin 4) and a logic HIGH on the ENABLE pin (pin 12) will force the driver outputs into high impedance (high-Z). Refer to the truth table in Table 1. All drivers are internally protected against short circuits on their outputs. The driver outputs are short-circuit limited to 150mA. The driver output skew times are typically 0.8ns. To minimize reflections, the multipoint bus transmission line should be terminated at both ends in its characteristic impedance, and stub lengths off the main line should be kept as short as possible. FIGURE 9. TWO-WIRE BALANCED SYSTEM, RS-422 TABLE 1: TRUTH TABLE, ENABLE/DISABLE FUNCTION COMMON TO ALL FOUR RS-422 DRIVERS ENABLE ENABLE INPUT NON-INVERTING A OUTPUT INVERTING B OUTPUT LOW HIGH don’t care high-Z high-Z HIGH don’t care LOW LOW HIGH don’t care LOW HIGH HIGH LOW 9 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 10. DIFFERENTIAL PROPAGATION DELAY VS TEMPERATURE FIGURE 11. DIFFERENTIAL PROPAGATION DELAY VS VOLTAGE 10 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 12. DIFFERENTIAL SKEW VS TEMPERATURE FIGURE 13. DIFFERENTIAL SKEW VS VOLTAGE 11 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 14. DIFFERENTIAL TRANSITION TIME VS TEMPERATURE FIGURE 15. DIFFERENTIAL TRANSITION TIME VS VOLTAGE 12 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 16. COMPLEMENTARY SKEW VS TEMPERATURE FIGURE 17. COMPLEMENTARY SKEW VS VOLTAGE 13 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 18. DIFFERENTIAL VOUT VS IOUT (TEMPERATURE) FIGURE 19. DIFFERENTIAL VOUT VS IOUT (VCC) 14 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 20. VOUT HIGH VS IOUT (TEMPERATURE) FIGURE 21. VOUT HIGH VS IOUT (VCC) 15 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 22. VOUT LOW VS CURRENT (TEMPERATURE) FIGURE 23. VOUT LOW VS CURRENT (VCC) 16 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 24. SUPPLY CURRENT VS TEMPERATURE FIGURE 25. SUPPLY CURRENT VS VOLTAGE 17 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 26. SUPPLY CURRENT VS DATA RATE FIGURE 27. ICC (LOADED) VS DATA RATE 18 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER FIGURE 28. SHORT CIRCUIT CURRENT VS TEMPERATURE FIGURE 29. SHORT CIRCUIT CURRENT VS VOLTAGE 19 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER PACKAGE DIMENSIONS (16 PIN NSOIC) 20 REV. 1.1.0 SP26LV431 REV. 1.1.0 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER PACKAGE DIMENSIONS (16 PIN PDIP) 21 SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER REV. 1.1.0 REVISION HISTORY DATE REVISION DESCRIPTION 3/08/04 A Production Release. 2/24/05 B Include tape and reel p/n’s. 9/05/08 1.0.0 Converted to Exar standard datasheet format. Add -40C to +85C temperature range option. Changed revision to 1.0.0. 2/19/09 1.1.0 Add 3ns maximum driver skew for industrial temperature option. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2009 EXAR Corporation Datasheet February 2009. Send your UART technical inquiry with technical details to hotline: [email protected]. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 22