FTR-K1 SERIES SIGNAL RELAY 2 POLES - 2A High Isolation Wide Contact Gap 2.0mm Contact Gap FTR-C2 Series n FEATURES DPDT 2A Contact gap: more than 2.0mm l Conforms to IEC60950 / EN60950 / UL1950/ CSA C22.2 ������ No.950 Working voltage 250V l INSULATION Clearance: 2.0 mm (between open contacts, coil and contacts, contact sets) Creepage: 2.5 mm (between open contacts,coil and contacts, contact sets) l HIGH RELIABILITY Bifurcated contacts l Power consumption 300 mW l Latching types available l RoHS compliant. Please see page 7 for more information l l n PARTNUMBER INFORMATION FTR-C2 C A 012 G [Example] (a) (b) (c) (d) (e) (a) Relay type FTR-C2: FTR-C2 Series (b) Terminal type������������� ������������ C : Through hole ���� G : Surface mount� (c) (d) ���������� Coil type� �� A B : Standard type : Latching type Coil rated voltage 012 : 3.....24 VDC Coil rating table at page 3� (e) Contact material G : Gold plated silver alloy Note: 500 relays per reel for SMT versions Remarks: Actual marking on relay would not carry code FTR and be as below: Ordering code: FTR-C2CA012G-B05 Actual marking: C2CA012G Note: * Only SMT version FTR-K1SERIES SERIES FTR-C2 n SPECIFICATION Item Contact Data Life Timing Data Insulation Latching type FTR-C2 ( ) A FTR-C2 ( ) B Configuration 2 form C Construction Bifurcated contacts Material Gold overlay silver palladium (stationary contact) Silver palladium (movable contact) Resistance (initial) Maximum 150 mΩ at 1 A, 6 VDC Contact rating (resistive) 0.3A, 125VAC / 1A, 30VDC Max. carrying current 2A Max. switching voltage 250 VAC / 220VDC Max. switching power 62.5VA / 30W Min. switching load * 0.01A, 10mVDC Mechanical 10 x 103 operations minimum (at 10 Hz) Electrical Coil Data Standard type DC contact rating 100 x 103 operations minimum AC contact rating 100 x 103 operations minimum Rated Power 300 mW 150 mW Operate Power 169 mW 85 mW Operating temperature range -40 °C to +85 °C (no frost) Operate (no bounce) ≤ 15 ms (at nominal voltage) Release (no diode, no bounce) ≤ 15 ms (at nominal voltage) Resistance (initial) ≥ 1,000MOhm at 500VDC Dielectric strength Open contacts 1,500VAC (50/60Hz) 1min Contacts to coil 1,500VAC (50/60Hz) 1min Adjacent contacts 2,000VAC (50/60Hz) 1min Surge strength Coil to contacts 2,500V/ 2 x 10µs standard wave Adjacent contacts 2.0 mm Clearance Open contacts 2.0 mm Coil and contacts 2.0 mm Adjacent contacts 2.0 mm Creepage Other Vibration resistance Shock Weight Open contacts 2.0 mm Coil and contacts 2.5 mm Misoperation 10 to 55Hz double amplitude 3.3mm Endurance 10 to 55Hz double amplitude 5.0mm Misoperation 300m/s² Endurance 1,000m/s² Approximately 3.79g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. FTR-C2 FTR-K1SERIES SERIES n COIL RATING Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 003 3 30 2.25 0.3 7.2 005 5 83.3 3.75 0.5 12 012 12 480 9 1.2 28.8 024 24 1,920 18 2.4 57.6 Rated Power (mW) 300 Latching type (1 coil) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * 003 3 60 +2.25 2.25 7.2 005 5 167 +3.75 3.75 12 012 12 960 +9 9 28.8 024 24 3,840 +18 18 57.6 Rated Power (mW) 150 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E 63615 0.3A, 125VAC (resistive) 1A, 30VDC 0.3A, 110VDC CSA C22.2 No. 14 LR 40304 FTR-C2 FTR-K1SERIES SERIES n REFERENCE DATA FTR-K1SERIES SERIES FTR-C2 n DIMENSIONS AND SCHEMATICS n TERMINAL DESIGNATIONS n RECOMMENDED MOUNTING PAD Single Coil Latching Type Unit: mm FTR-K1SERIES SERIES FTR-C2 n DIMENSIONS AND SCHEMATICS Unit: mm n TERMINAL DESIGNATIONS n RECOMMENDED MOUNTING PAD Single Coil Latching Type Unit: mm FTR-K1SERIES SERIES FTR-C2 RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. l Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. REFLOW Note: 1.Temperature profiles show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces can vary, depending on the size of PC board, status of parts mounting and heating method. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. l 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l FTR-K1SERIES SERIES FTR-C2 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. March 15, 2010