PID-95, PID-95P Description Point Identification Device CS-2044ph1.wmf The Gamewell-FCI PID-95-P addressable point identification device is the interface between the non-powered, normally open, dry-contact devices and Gamewell-FCI’s 600 Series of analog addressable Fire Alarm Control Panels (FACPs). Point identification devices monitor a single Style B circuit, and are designed for concealed mounting in an electrical backbox. The PID-95P can be surface-or-flush mounted and has a visible LED for alarm/annunciation. Operation The point identification device connects to the Signaling Line Circuit (SLC) via two wires. The PID-95 will monitor, via a two-wire supervised SLC circuit, contact-type devices such as a waterflow switch or manual station. Upon activation of the monitored device, the PID-95 will report its address to the 600 Series FACP via the analog SLC. The control panel will then activate into all alarm programmed outputs related to the PID-95. Features Programming The PID-95 is programmed by setting a single DIP switch, easily accessible on the device’s printed circuit board. The DIP switch sets the address of the device and the priority interrupt (DIP SW #8). All other programming is accomplished at the FACP through a laptop computer or the control panel operator’s display. PID-95P PID-95 • Monitors dry-contact devices. • LED for alarm annunciation. • Supervises DC power in. • Field programmable. • Priority interrupt. • Plate-mounted version available for surface or flush mounting in 4" (11 cm) square, 4.688" (11.908 cm), or double gang boxes. Standard Application The PID-95 is the interface between dry-contact type devices and the SLC of the control panel. The PID-95 is a means of connecting and identifying monitor points without the use of conventional input modules at the main control panel. The use of PID-95s can dramatically reduce the field wiring required on many projects. An ISO 9000-2000 Company SIGNALING FM Microsoft® Windows® is a registered trademark of Microsoft® Corporation. S521 APPROVED MEA Approved 7300-1288:147 GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use. ©2007 Honeywell International Inc. All rights reserved. www.gamewell-fci.com CS-2044 Rev. A page 1 of 2 Ordering Information Engineer’s Specifications Addressable interface devices shall be provided for the monitoring and supervision of contact type devices connected to the Fire Alarm Control Panel. The devices shall monitor a normally open dry contact. The addressable interface devices shall communicate to the main control panel via the analog addressable circuit. The interface device shall be Gamewell-FCI PID-95 or PID-95P. Model Description PID-95 Addressable point identification device for monitoring contact devices. Addressable input interface device mounted on 4.688" (11.908 cm) plastic plate. Trim ring for flush-mounting on the PID-95P. PID-95P 70839 Specifications PID-95 Standby Current: Alarm Current: Operating Temperature: Relative Humidity: Mounting: 0.0005 A 0.0015 A 0° C to 49° C (32°F to 120 °F) 85%, non-condensing 4" (10.16 cm) square backbox with blank cover plate PID-95P Standby Current: Alarm Current: Operating Temperature: Relative Humidity: Mounting: 0.0005 A 0.0015 A 0° C to 49° C (32°F to 120°F) 85%, non-condensing 4" (11 cm) 4.688" (11.908 cm), double gang Backbox. GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 www.gamewell-fci.com CS-2044 Rev. A page 2 of 2