MPD D307RW

D300RW
Series
Single & Dual Output
3W SIP, Wide Input
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• 3W Output Power
• 2:1 Input Voltage Range
• 1,500 VDC Isolation
• Short Circuit Protected
• Miniature SIP Case
• Single & Dual Outputs
• 1.0 MH MTBF
• Industry Standard Pin-Out
Parameter
Input Voltage Range
Conditions
Min.
Typ.
Max.
12 VDC Input
9.0
12.0
18.0
24 VDC Input
18.0
24.0
36.0
Short Circuit Input Power
1,500
Units
VDC
mW
Output
Typ.
Max.
Units
Output Voltage Accuracy
Parameter
±1.0
±3.0
%
Output Voltage Balance
±1.0
±2.0
%
Line Regulation
Conditions
Min.
Vin = Min to Max
±0.2
±0.5
%
Load Regulation , Single Output
Iout = 10% to 100%
±0.5
±0.75
%
Load Regulation , Dual Output
Iout = 10% to 100%
±0.5
±1.0
%
50
100
mV P - P
±0.03
%/°C
Max.
Units
Ripple & Noise (20 MHz) (Note 1)
Output Power Protection
120
%
Temperature Coefficient
Output Short Circuit
Continuous (Autorecovery)
General
RoHS Compliant
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Min.
60 Seconds
1,500
500 VDC
1,000
Isolation Capacitance
100 kHz, 1V
Switching Frequency
Iout = 100%
Typ.
VDC
MΩ
80
200
pF
500
kHz
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
Humidity
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Reliability Specifications
Typ.
Max.
Units
-40
+25
+85
°C
+125
°C
95
%
-50
Cooling
MicroPower Direct
Min.
Free Air Convection
RH, Non-condensing
Case Size
0.87 x 0.47 x 0.37 Inches (22.0 x 12.0 x 9.50 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
Parameter
MTBF
0.20 Oz (6.0g)
Conditions
Min.
MIL HDBK 217F, 25°C, Gnd Benign
1.0
Conditions
Min.
Typ.
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Typ.
Max.
12 VDC Input
-0.7
22.0
24 VDC Input
-0.7
40.0
1.5 mm From Case For 10 Sec
All Models
Units
VDC
300
°C
1,800
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D301RW
D302RW
D303RW
D304RW
D305RW
D306RW
D307RW
D308RW
D311RW
D312RW
D313RW
D314RW
D315RW
D316RW
D317RW
D318RW
Input
Output
Efficiency
Voltage (VDC)
Current (mA)
Voltage Current
Current
(%, Typ)
(VDC)
(mA,
Max)
(mA,
Min)
Nominal
Range
Full-Load No-Load
12
9.0 - 18.0
320
22
5.0
600.0
60.0
78
12
9.0 - 18.0
316
22
9.0
333.0
33.0
79
12
9.0 - 18.0
312
22
12.0
250.0
25.0
80
12
9.0 - 18.0
312
22
15.0
200.0
20.0
80
12
9.0 - 18.0
320
22
±5.0
±300.0
±30.0
78
12
9.0 - 18.0
316
22
±9.0
±167.0
±17.0
79
12
9.0 - 18.0
312
22
±12.0
±125.0
±13.0
80
12
9.0 - 18.0
312
22
±15.0
±100.0
±10.0
80
24
18.0 - 36.0
160
10
5.0
600.0
60.0
78
24
18.0 - 36.0
158
10
9.0
333.0
33.0
79
24
18.0 - 36.0
156
10
12.0
250.0
25.0
80
24
18.0 - 36.0
154
10
15.0
200.0
20.0
81
24
18.0 - 36.0
160
10
±5.0
±300.0
±30.0
78
24
18.0 - 36.0
158
10
±9.0
±167.0
±17.0
79
24
18.0 - 36.0
156
8
±12.0
±125.0
±13.0
80
24
18.0 - 36.0
154
8
±15.0
±100.0
±10.0
81
Notes:
1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single
output units and from each output to common for dual output units.
2. These units should not be operated with a load under 10% of full load. Operation
at no-load may cause damage to the unit.
3. These converters are specified for operation without external components. However,
in some applications the addition of input/output capacitors will enhance stability and
reduce output ripple.
Output Capacitor
Recommended capaciInput
Vin Capacitor
Vout 0 - 70ºC -40 - 85ºC
tor values are given in
(Electrolitic) (Tantalum)
the table at right. Using
100 µF
5 VDC
100 µF
47 µF
simple LC filter networks 12 VDC
100 µF
47 µF
on the input/output will 24 VDC 10 - 47 µF 9 VDC
provide further improve12 VDC
100 µF
47 µF
ment. This only requires
15 VDC
100 µF
47 µF
the addition of small
inductors to the input/output filter circuits. Recommended values are 4.7 µH to 120
µH for an input inductor and 2.2 µH to 10 µH for an output inductor.
Output ripple on single output units may
Output Voltage
be further enhanced by using the CS terminal (single output units operated at 50%
5V
9V
12V
15V
load or below should use this function). A
CS
47 µF - 100 µF 22 µF - 47 µF
low ESR capacitor is connected between
the CS pin and the -Vout pin (the anode of the capacitor is connected to the -Vout
pin). Recommended capacitor values are given in the table above. If not used, the
CS pin should be left open.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output.
To do this, connect the load across the +Vout and -Vout outputs and float the
output common.
Min
Max
5. The remote on/off control pin is referenced
On
<0.6 VDC to Open Circuit
to the -Vin pin (pin 1). Input current to the
pin should be between 5 - 10 mA with a
Off
2.7 VDC
15.0 VDC
maximum of 20 mA.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating.
Capacitive Load
Output
Max Cap Load
5.0 VDC
9.0 VDC
12.0 VDC
15.0 VDC
±5.0 VDC
±9.0 VDC
±12.0 VDC
±15.0 VDC
2,200 µF
1,000 µF
820 µF
680 µF
±560 µF
±470 µF
±330 µF
±220 µF
Fuse Rating
Slow-Blow
(mA)
700
700
700
700
700
700
700
700
350
350
350
350
350
350
350
350
Mechanical Dimensions
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
Derating Curve
Pin Connections
Pin Single
Dual
1
-Vin
-Vin
2
+Vin
+Vin
3
Remote ON/OFF
5
NF
NF
6 +Vout
+Vout
7
-Vout Common
8
CS
-Vout
NF = No Function
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]