RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ELECTRONIC COMPONENTS ■ ■ ■ ■ SP-480 Änderungen vorbehalten / subject to change without notice 480W Single Output with PFC Function series Features : Universal AC input / Full range Built in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Forced air cooling by built-in DC fan 3 High power density 5.18w/in Low profile:43mm thickness Built-in remote ON-OFF control Built-in remote sense function Active AC surge current limiting 3 years warranty SPECIFICATION MODEL SP-480-3.3 SP-480-24 SP-480-48 3.3V 5V 12V 15V 24V 48V 85A 85A 40A 32A 20A 10A CURRENT RANGE 0 ~ 85A 0 ~ 85A 0 ~ 43A 0 ~ 35A 0 ~ 22A 0 ~ 11A RATED POWER 280.5W 425W 480W 480W 480W 480W Note.5 280.5W 425W 516W 525W 528W 528W 80mVp-p 120mVp-p 150mVp-p 150mVp-p 240mVp-p 4.5 ~ 5.5V 2.0% 10.8 ~ 13.2V 1.5% 13.5 ~ 18V 1.5% 22 ~ 27.6V 1.0% 41~ 56V 1.0% RIPPLE & NOISE (max.) Note.2 80mVp-p VOLTAGE ADJ. RANGE 2.9 ~ 3.6V VOLTAGE TOLERANCE Note.3 2.0% LINE REGULATION 0.5% 0.5% 0.3% 0.3% 0.2% 0.2% LOAD REGULATION 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 1000ms, 80ms/230VAC 18ms/230VAC HOLD TIME (Typ.) VOLTAGE RANGE 2500ms, 80ms/115VAC at full load 18ms/115VAC at full load Note.7 85 ~ 264VAC 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 73% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 6.5A/115VAC 3.5A/230VAC 20A/115VAC <2mA / 240VAC 40A/230VAC LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE Note.4 FUNCTION SP-480-15 RATED CURRENT SETUP, RISE TIME INPUT SP-480-12 DC VOLTAGE PEAK LOAD(10min.) OUTPUT SP-480-5 REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY ENVIRONMENT TEMP. COEFFICIENT VIBRATION PF>0.98/115VAC at full load 79% 85% 85% 87% 89% 87 ~ 103A 87 ~ 103A 45.15 ~ 58.05A 36.75 ~ 47.25A 23.1 ~ 29.7A Protection type : Constant current limiting, recovers automatically after conditions is removed 3.8 ~ 4.45V 5.75 ~ 6.75V 13.8 ~ 16.2V 18 ~ 21V 28.8 ~ 33.6V Protection type : Shut down o/p voltage, re-power on to recover 11.55 ~ 14.85A 57.6 ~ 67.2V 80 (TSW1) Detect on heatsink of power transistor 90 (TSW2) Detect on heatsink of power diode Protection type : Shut down o/p voltage, recovers automatically after temperature goes down RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off -20 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 0.03%/ , 10 ~ 95% RH (0 ~ 50 SAFETY STANDARDS 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:Short I/P-O/P, I/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 6) HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY MTBF OTHERS NOTE DIMENSION PACKING Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN61000-6-2 (EN50082-2) light industry level, criteria A 120.5K hrs min. MIL-HDBK-217F (25 ) 278*127*43mm (L*W*H) 1.7Kg; 6pcs/11.3Kg/0.67CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. TSW1: Detect on heatsink of power transistor. TSW2: Detect on heatsink of output diode. 5. 33% Duty cycle maximum within every 30 minute. Average output power should not exceed the rated power. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 7. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:SP-480-SPEC 2006-04-13 RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ■ ■ ELECTRONIC COMPONENTS ■ ■ SP-480 Änderungen vorbehalten / subject to change without notice 480W Single Output with PFC Function Mechanical Specification Case No. 929A 216 series Unit:mm 31 21 36 33.5 19 CN51 2 5 14 ADJ. 4-M4 9 Air flow direction 8 89 127 6 5 60 11 7 9.25 4 3 2 11.5 1 1.5 216 278 19 Terminal pin number assignment : Pin No. 1 2 3 Assignment AC/L AC/N FG Pin No. 4~6 7~9 8.8 25.4 43 4-M4 L=6 31 Connector pin number assignment (CN51) : JST B6B-PHDSS or equivalent Assignment -V +V Pin No. 1 2 3 Assignment GND RC-S Pin No. 4 5 6 Assignment N.C. RC+ +S Mating Housing Terminal JST PHDR-06VS or equivalent JST SPHD-002T-P0.5 or equivalent Block Diagram fosc : 100KHz FAN +S ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & P.F.C. POWER SWITCHING RECTIFIERS & FILTER +V -V (GND) -S FG O.L.P. O.T.P. DETECTION CIRCUIT PFC/PWM CONTROL O.V.P. RC+ RC- Derating Curve Static Characteristics Ta=25 100 100 90 1 80 80 2 1 Others 70 2 3.3,5V Only LOAD (%) LOAD (%) 60 40 20 -20 0 10 20 30 40 AMBIENT TEMPERATURE ( 50 ) 60 (HORIZONTAL) 60 50 40 85 90 115 120 140 165 180 200 220 240 260 INPUT VOLTAGE (VAC) 60Hz File Name:SP-480-SPEC 2006-04-13