ML5825 2.4GHz to 5.8GHz Frequency Translator ADVANCED Datasheet GENERAL DESCRIPTION The ML5825 is a high integration 2.4GHz - 5.8GHz frequency translator (transverter). It upconverts 2.4GHz signals to 5.8GHz and downconverts received 5.8GHz signals to 2.4GHz. Transmit and receive utilize the same low noise fixed local oscillator (LO). It is intended to be used in conjunction with a 2.4GHz transceiverbased solution to quickly and easily develop a 5.8GHz solution while fully leveraging previous development. The ML5825 receive chain contains a Low Noise Amplifier (LNA), bandpass filter and image reject down conversion mixer. A digitally controlled 18dB gain step in the receive chain provides an innovative solution for optimizing IIP3 (low gain mode) and Noise Figure (high gain mode). On the transmit side, the ML5825 buffers and upconverts a differential 2.4GHz signal to 5.8GHz, where it is filtered and amplified. The ML5825’s PLL accepts two industry-standard input clock frequencies. The ML5825’s low STANDBY MODE current maximizes battery life. Power supply regulation is included in the ML5825, providing circuit isolation and consistent performance over supply voltages between 2.8V-3.6V. VTXB PIN 1 VMIX VSSMX High Integration 2.4GHz to 5.8GHz Transverter Receive LNA, Image Reject Filter & Mixer Transmit Pre-Driver, Filters & Mixers Fully Integrated PLL-Based Synthesizer Selectable Receive Gain Optimizes NF and IIP3 Interfaces Directly with Many 2.4GHz Transceivers 4dB (typ. High Gain Mode) Noise Figure -14dBm Input IP3 (Low Gain Mode) Selectable Transmit Output Power 10μA Standby Mode Space-saving 28 pin QFN package APPLICATIONS 5.8GHz Digital Cordless Telephones 5.8GHz Streaming Audio & Video Upconverted 2.4GHz Standards o Bluetooth o Zigbee/802.15.4 TXO VBG1 VREG4 Top View RXI VLNA PIN CONFIGURATION FEATURES BLOCK DIAGRAM TXISET TXIN * RXON TXIP RXOP VREG3 RFISET QPO VTUNE 2 VBG2 RXGN VREG2 VCCA VTUNE REFSEL FREF VSSLO XCEN TXIN, TXIP 2383-2508 MHz TXISET TXO 5725-5850 MHz Control Logic TX Subsystem VSSPLL QPO VREG1 XCEN TXON REFSEL TXON FREF Supply Regulation & Voltage Reference PLL * GROUND/RETURN ON EXPOSED PADDLE ORDERING INFORMATION RX Subsystem GAIN CONTROL PART NUMBER TEMP RANGE PACKAGE PACK (QTY) ML5825DM -10oC to +60oC 28QFN 4x5x0.9 mm Antistatic Tray (490) ML5825DM-T -10oC to +60oC 28QFN 4x5x0.9 mm Tape & Reel (2500) SEPTEMBER 2007 VCCA VBG1 VBG2 VREGn RFISET RXI 5725-5850 MHz 2 RXGN RXON, RXOP 2383-2508 MHz EDS-106038 REV A01 ML5825 TABLE OF CONTENTS GENERAL DESCRIPTION ........................................................................................................................................... 1 PIN CONFIGURATION ................................................................................................................................................. 1 ORDERING INFORMATION ........................................................................................................................................ 1 FEATURES ................................................................................................................................................................... 1 APPLICATIONS ............................................................................................................................................................ 1 BLOCK DIAGRAM ........................................................................................................................................................ 1 TABLE OF CONTENTS ................................................................................................................................................ 2 SIMPLIFIED APPLICATIONS DIAGRAM ..................................................................................................................... 2 ELECTRICAL CHARACTERISTICS............................................................................................................................. 3 PIN DESCRIPTIONS.................................................................................................................................................... 5 FUNCTIONAL DESCRIPTION ..................................................................................................................................... 9 MODES OF OPERATION............................................................................................................................................. 9 PHYSICAL DIMENSIONS .......................................................................................................................................... 11 WARRANTY................................................................................................................................................................ 12 SIMPLIFIED APPLICATIONS DIAGRAM Figure 1: ML5825 Typical Application Schematic ADVANCED DATASHEET SEPTEMBER 2007 2 EDS-106038 REV A01 ML5825 ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Operating the device for any length of time beyond the operating conditions may degrade device performance and/or shorten operating lifetime. VCCA.......................................................................................................................................................................... 3.6 V Maximum Receive RF Input Power....................................................................................................................... +13dBm Maximum Transmit RF Input Power........................................................................................................................ +3dBm Junction Temperature............................................................................................................................................... 150°C Storage Temperature Range ...................................................................................................................... -65°C to 150°C Lead Temperature (Soldering, 10s).......................................................................................................................... 260°C Thermal Resistance (θJA) ........................................................................................................................................ 39°C/W OPERATING CONDITIONS Ambient Temperature Range ....................................................................................................................... -10°C to 60°C VCCA Range ...................................................................................................................................................2.8V to 3.6V Unless otherwise specified, VCCA=3.2V, TA=-10°C to +60°C, XCEN=VIH, PINRX=-40dBm, PINTX=-3dBm, PLL Loop Filter Bandwidth=40 KHz, and gain control in either state. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 2.8 3.2 3.6 V 10 μA POWER SUPPLIES VCCA ISTBY Analog supply voltage Supply current, STANDBY mode VCCA=3.6V, XCEN=VIL, TXON= VIL OR VIH IRX Supply current, RECEIVE mode TXON= VIL 45 60 mA ITX Supply current, TRANSMIT mode TXON= VIH RTXISET=7.5KΩ 95 110 mA RTXISET=5.5KΩ 100 115 mA SUPPLY REGULATION VR27 Regulated Output Voltage Pins 12, 19, 26 2.7 V VR25 Regulated Output Voltage Pin 17 2.5 V VBG Bandgap Voltage Pins 18 & 25 1.25 V 3342.336 MHz SYNTHESIZER fLO Local Oscillator Frequency IP Charge Pump sink/source current This is a function of VTUNE to compensate for the change in KV FOUT = FIN+/- FLO VTUNE =1.2V 0.49 KV FPULL FPTR Phase noise at driver output 0.71 0.60 mA mA 0.38 VTUNE =1.9V ΦN mA 0.90 VTUNE =0.3V 400mVp-p sine wave reference dBc/Hz fo=10KHz offset from fc -65 fo=1.2MHz offset from fc -115 -110 dBc/Hz 230 350 MHz/V VCO Tuning sensitivity 100 Frequency pulling 70μs after PIN –50dBm to +12dBm +/-20 KHz Frequency pulling TX to RX 70μs after transition +/-20 KHz <.5 MHz/V and RX to TX FPUSH Frequency pushing Vary VCCA from 2.9V to 3.6V tWAKE Settling time from standby XCEN=VIH, to within 10KHz ADVANCED DATASHEET SEPTEMBER 2007 3 200 μs EDS-106038 REV A01 ML5825 SYMBOL fFREF VFREF PARAMETER CONDITIONS Reference signal frequency Reference signal level MIN TYP MAX UNITS REFSEL=VIL 18.432 MHz REFSEL=VIH 24.576 MHz AC coupled 400 1200 mVp-p RECEIVER FRXI Receiver Input Frequency Range FRXO Receiver Output Frequency Range 5.725 - 5.850 GHz 2.382664 - 2.507664 GHz ZRIN Receiver Input Impedance Over FRXI 37 + j2 Ω ZRXO Receiver Output Impedance Differential Impedance RXON/RXOP Over FRXO 100 Ω Input noise figure High Gain Mode 4.0 7.0 dB Low Gain Mode 14 22 dB NF GRX IIP3 P1dB PRXI PSPUR RX Power Gain High Gain Mode Pin=-50dBm Low Gain Mode Pin=-30dBm High Gain Mode For Pin=-50dBm each tone spaced +/-1MHz from 5800MHz Low Gain Mode For Pin=-30dBm each tone spaced +/1MHz from 5800MHz Input IP3 RX Input 1dB compression RX conducted emissions from RF input port 13 dB -8 dB dBm -25 dBm -14 High Gain Mode -35 dBm Low Gain Mode -25 dBm RXI terminated in 50 ohm -50 dBm Out of Band Spurious, High Gain Mode Low Gain Mode IRR 8 RX Image Rejection Spurs outside Receive Output Frequency Range From RXI to RXO, Pin=-50dBm, FRXI= 835-965MHz -25 dBc -5 dBc 20 dB TRANSMITTER FTXI Transmitter Input Frequency Range FTXO Transmitter Output Frequency Range ZTXI Transmitter Input Impedance ZTXO POUT 2.382664 - 2.507664 GHz 5.725-5.850 GHz Differential Impedance TXIN/TXIP Over FTXI 100 Ω Transmitter Output Impedance Over FTXO 43 + j88 Ω TX buffer output power at 5.85 GHz RTXISET=7.5KΩ, Pin=-6dBm 3.5 dBm Matched into 50 ohms, RTXISET=5.5KΩ, Pin=-3dBm 5.5 dBm RTXH Transmit harmonic output rejection 50 Ohm load RLO Transmit LO feed thru Measured at TXO port with CW signal at FTXI and PTXI -30 dBc RRFIF Transmit IF feed thru Measured at TXO port with CW signal at FTXI and PTXI -30 dBc R2LO Transmit 2xLO feed thru Measured at TXO port with CW signal at FTXI and PTXI <-30 dBc R3LO Transmit 3xLO feed thru Measured at TXO port with CW signal at FTXI and PTXI <-20 dBc R4LO Transmit 4xLO feed thru Measured at TXO port with CW signal at FTXI and PTXI <-20 dBc RTSB Transmit lower sideband rejection From TXI to TXO ports at PTXI for FTXO= 835-960MHz ADVANCED DATASHEET SEPTEMBER 2007 4 <-20 25 dBc dBc EDS-106038 REV A01 ML5825 SYMBOL RMXN PARAMETER CONDITIONS Mixer products rejection at output port From TXI to TXO ports at PTXI for FTXO= 960-970MHz MIN TYP MAX >55 UNITS dBc INTERFACE LOGIC LEVELS Input pins (XCEN, TXON, RXGN, REFSEL) VIH Input high voltage VCCA*0.7 VCCA+0.4 V VIL Input low voltage -0.4 VCCA*0.3 V IB Input bias current All states -5 5 μA CIN Input capacitance 1MHz test frequency 4 pF PIN DESCRIPTIONS PIN NAME I/O FUNCTION DIAGRAM POWER & GROUND 2 VSSMX 7 VCCA 14 VSSPLL 15 VSSLO 24 VTXB X VSSDB GROUND Mixer Ground N/A Regulated External Supply, Requires Proper Decoupling Components N/A GROUND PLL Ground N/A GROUND VCO and LO Ground N/A POWER INPUT GROUND TX Buffer Supply Voltage, Connect to Pin 7 N/A Exposed Paddle. Ground/Return N/A 2.7V Supply Decoupling Point, Connect to Pin 26 N/A SUPPLY REGULATION 1 VMIX INPUT 12 VREG1 OUTPUT 2.7V Regulated Supply Output N/A 17 VREG2 OUTPUT 2.5V Regulated Supply Output N/A 18 VBG2 OUTPUT 1.24V Bandgap2 Supply Decoupling Point N/A 19 VREG3 OUTPUT 2.7V Regulated Supply Decoupling Point N/A 25 VBG1 OUTPUT 1.24V Bandgap1 Supply Decoupling Point N/A 26 VREG4 OUTPUT 2.7V Regulated Supply Output, Connect to Pins 1 and 28 N/A 28 VLNA 2.7V LNA Supply Decoupling Point, Connect to Pin 26 N/A INPUT ADVANCED DATASHEET SEPTEMBER 2007 5 EDS-106038 REV A01 ML5825 RF TRANSMIT/RECEIVE DATA 27 RXI I (analog) 5.8GHz RX Input. A simple matching network is required for optimum noise figure. This input connects to the base of an NPN transistor and should be AC coupled. VLNA 28 0.7V 3.9K RXI 27 VSSDB 23 TXO O (analog) 5.8GHz TX Output into a matched load over the 5725 to 5850 MHz range. VTXB 24 TXO 23 VSSDB 4 RXOP 3 RXON O (analog) Differential 2.4GHz RX Output. VCCA 7 56Ω RXOP 4 2 VSSMX 20 TXIP 21 TXIN I (analog) Differential 2.4GHz TX Input VCCA 7 22Ω TXIP 20 TXIN 21 ADVANCED DATASHEET SEPTEMBER 2007 6 VSSDB 82Ω 2 X VSSMX VSSDB EDS-106038 REV A01 ML5825 RF CONTROL & OTHERS 11 XCEN I (CMOS) Transceiver Enable Input. Enables the bandgap reference and voltage regulators when high. Consumes only leakage current in STANDBY mode when low. This is a CMOS input, and the thresholds are referenced to VCCA and VSSMX. VCCA 7 XCEN 11 168Ω 2 VSSMX 10 TXON I (CMOS) TX/RX Control Input. Switches the transceiver between TRANSMIT and RECEIVE modes. Circuits are powered up and signal paths reconfigured according to the operating mode. This is a CMOS input, and the thresholds are referenced to VCCA and VSSMX. VCCA 7 TXON 10 168Ω 2 VSSMX 5 RFISET I (analog) Connect to a 255Ω +/-1% resistor to ground. VCCA 7 RFISET 5 2 VSSMX 6 RXGN I (CMOS) Gain Step Input Control. Switches the receiver between high gain (when HIGH) and low gain (when LOW). This dual-gain design allows the system designer to achieve low noise figure for low input signals while maintaining a good IIP3 under high input signal conditions. This is a CMOS input, and the thresholds are referenced to VCCA and VSSMX. VCCA 7 RXGN 6 168Ω 2 VSSMX ADVANCED DATASHEET SEPTEMBER 2007 7 EDS-106038 REV A01 ML5825 13 QPO O (analog) Charge Pump Output. This output is connected to the external PLL loop filter. Sources current when the LO frequency is lower than desired. VREG1 12 QPO 13 9.2Ω 14 VSSPLL 16 VTUNE I (analog) VCO Tuning Voltage. This input from the PLL loop filter determines the output frequency and is very sensitive to noise coupling and leakage currents. VREG3 19 VTUNE VREG2 16 17 10Ω 15 VSSLO 22 TXISET I (analog) A resistor between this pin and ground establishes the PA output power compression point by setting a bias current. VTXB 24 VCCA 7 TXISET 22 522Ω 2 VSSMX 8 FREF I (analog) Input Reference Frequency. Depending on the state of the REFSEL pin this input is divided by 3 or 4 to generate the PLL reference frequency. VCCA 7 VREG1 12 FREF 8 2 VSSMX 14 VSSPLL 9 REFSEL I (CMOS) Reference Divider Control. If REFSEL is HIGH, FREF is divided by 4, otherwise FREF is divided by 3. This is a CMOS input, and the thresholds are referenced to VCCA and VSSMX. VCCA 7 REFSEL 9 168Ω 2 VSSMX ADVANCED DATASHEET SEPTEMBER 2007 8 EDS-106038 REV A01 ML5825 FUNCTIONAL DESCRIPTION The ML5825 is a monolithic, bilateral 2.4GHz to 5.8GHz frequency translator. It provides a simple and straightforward solution for designers of 2.4GHz products who want to develop advanced products for the relatively interference-free 5.8GHz band, especially digital cordless telephones. The ML5825 can implement “dual band” solutions that use both the 2.4GHz and 5.8GHz bands as well as “hybrid” products where one link (say, basestation transmission) is at 5.8GHz, while the other link (basestation receive) is at 2.4GHz. 5.8GHz signals enter the RXI pin and then are fed to an LNA and bandpass filter. An image-reject downconvert mixer translates the signal to the 2.4GHz ISM band where it is then buffered and sent off chip differentially on RXON/RXOP. The receive signal path can be configured for either a “High Gain” mode (about 13dB) or “Low Gain” mode (-8dB). Gain mode is selected via the RXGN digital input pin. High Gain mode is used for low-level input signals to minimize Noise Figure while Low Gain mode optimizes input IP3 for stronger signals. 2.4GHz signals come into the ML5825 differentially on the TXIP/TXIN pins, where they are upconverted to 5.8GHz, bandpass filtered, and then amplified and exit via TXO. The predriver/buffer output power compression point is programmed by an external resistor that sets the preamp bias level. A fully integrated phase locked loop (PLL) generates the fixed local oscillator (LO) at 3342.336 MHz which is used for upconverting and downconverting the RF signals. The comparison frequency of the PLL is derived from the frequency reference present on the FREF pin and the state of REFSEL as shown in Table 1. The PLL loop filter is external to the ML5825 so that lock time and in-band phase noise can be optimized for the system of interest. REFSEL REFERENCE DIVISION FREF VIL 3 18.432 MHz VIH 4 24.576 MHz Table 1: ML5825 Frequency References The ML5825 contains two separate bandgap references and several low dropout (LDO) voltage regulators to insure consistent performance over supply voltage and minimize crosstalk on chip. The device is enabled by bringing XCEN to VIH and is placed in transmit mode by setting TXON to VIH. With XCEN at VIL the ML5825 enters a low power standby mode. MODES OF OPERATION The ML5825 has three key modes of operation. The two operational modes are RECEIVE and TRANSMIT, controlled by TXON. XCEN is the chip enable/disable control pin, which sets the device in operational or STANDBY modes. The relationship between the parallel control lines and the mode of operation of the IC is summarized in Table 2. XCEN TXON MODE NAME FUNCTION 0 X STANDBY Standby. All circuits powered down 1 0 RECEIVE Receive Chain Active 1 1 TRANSMIT Transmit Chain Active Table 2: Modes of Operation ADVANCED DATASHEET SEPTEMBER 2007 9 EDS-106038 REV A01 ML5825 STANDBY MODE In STANDBY mode, the ML5825 transverter is powered down. When exiting STANDBY mode, the transmitter is disabled for 200μs. However, the receive path is not similarly locked out and so will receive invalid data for up to 200μs. Therefore, the system should wait 200μs after exiting STANDBY mode before actively processing signals to allow the PLL to lock. A timing diagram for the ML5825 is shown in Figure 2. VCCA 200uS XCEN TXON 170uS 350uS 200uS Data Output (RX & TX) 100uS RX Valid Data Output TX Valid Data Output Supply and PLL Settling 200uS PLL Settling 100uS 100uS TX Valid Data Output Supply Settling And TX Timer 170uS Time to valid TX data is 400uS RX Valid Data Output PLL Settling 100uS Figure 2: ML5825 Control Timing Diagram, assuming a 40 KHz loop bandwidth. RECEIVE MODE In RECEIVE mode, the received signal at 5.8GHz is amplified, filtered, and downconverted to 2.4GHz. The receiver has two gain modes; High Gain (about 13dB) and Low Gain (about -8dB). Gain mode is set via the state of the RXGN input, with High Gain Mode corresponding to a logic “1” on RXGN. TRANSMIT MODE In TRANSMIT mode, the transmitted signal at 2.4GHz is upconverted, filtered, and amplified at 5.8GHz. The transmit output power compression point is programmable via an external resistor on the TXISET pin. ADVANCED DATASHEET SEPTEMBER 2007 10 EDS-106038 REV A01 ML5825 PHYSICAL DIMENSIONS Figure 3: 28 Pin QFN Package Dimensions ADVANCED DATASHEET SEPTEMBER 2007 11 EDS-106038 REV A01 ML5825 WARRANTY Sirenza Microdevices makes no representations or warranties with respect to the accuracy, utility, or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, express or implied, by estoppel or otherwise, to any patents or other intellectual property rights is granted by this document. The circuits contained in this document are offered as possible applications only. Particular uses or applications may invalidate some of the specifications and/or product descriptions contained herein. The customer is urged to perform its own engineering review before deciding on a particular application. Sirenza Microdevices assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Sirenza Microdevices products including liability or warranties relating to merchantability, fitness for a particular purpose, or infringement of any intellectual property right. Sirenza Microdevices products are not designed for use in medical, life saving, or life sustaining applications. If this document is “Advanced”, its contents describe a Sirenza Microdevices product that is currently under development. All detailed specifications including pinouts and electrical specifications may be changed without notice. If this document is “Preliminary”, its contents are based on early silicon measurements. Typical data is representative of the product but is subject to change without notice. Pinout and mechanical dimensions are final. Preliminary documents supersede all Advanced documents and all previous Preliminary versions. If this document is “Final”, its contents are based on a characterized product, and it is believed to be accurate at the time of publication. Final Data Sheets supersede all previously published versions. This document is Advanced. © 2007 Sirenza Microdevices Corporation. All rights reserved. All other trademarks are the property of their respective owners. Products described herein may be covered by one or more of the following U.S. patents: 4,897,611; 4,964,026; 5,027,116; 5,281,862; 5,283,483; 5,418,502; 5,508,570; 5,510,727; 5,523,940; 5,546,017; 5,559,470; 5,565,761; 5,592,128; 5,594,376; 5,652,479; 5,661,427; 5,663,874; 5,672,959; 5,689,167; 5,714,897; 5,717,798; 5,742,151; 5,747,977; 5,754,012; 5,757,174; 5,767,653; 5,777,514; 5,793,168; 5,798,635; 5,804,950; 5,808,455; 5,811,999; 5,818,207; 5,818,669; 5,825,165; 5,825,223; 5,838,723; 5.844,378; 5,844,941. Japan: 2,598,946; 2,619,299; 2,704,176; 2,821,714. Other patents are pending. Sirenza Microdevices, Inc., 303 S. Technology Court, Broomfield, CO 80021, USA North America 1- 303-327-3030 z China +86-21-5835-4840 z India +91-80-32902348 www.sirenza.com z [email protected] z [email protected] ADVANCED DATASHEET SEPTEMBER 2007 12 EDS-106038 REV A01