SOURCE XP-MR-D12-CDA

10 Gbps 120km Multirate XFP Transceiver
Preliminary
XP-MR-D12-CDA
Features
• XFP MSA Rev 4.5 compliant
• 120km Reach over SMF-28 fiber utilizing Electronic Dispersion
Compensation (EDC)
• Supports 9.95Gb/s, 10.31Gb/s, 10.52Gb/s, 10.7Gb/s, and 11.1Gb/s
• Cooled EML with isolator
• APD Receiver
• Power dissipation <3.5W
• -5 to 70 C temperature range
• Digital Diagnostics
• XFI High Speed Electrical Interface
• RoHS Compliant
• Class 1 Laser, 21CFR 1040.10/1040.11
• EN 60825-1/A1:2002 Compliant
• Bail Latch Color: WHITE
Absolute Maximum Rating
Parameter
Symbol
Min
Typical
Max
Unit
Maximum Supply Voltage (3.3V)
Vcc3
-0.3
-
3.6
V
Maximum Supply Voltage (5.0V)
Vcc5
-0.3
-
5.5
V
Maximum Supply Voltage (1.8V)
Vcc2
-0.3
-
2
V
Tst
-40
-
85
ºC
Storage Temperature
General Operations
Parameter
Symbol
Min
Typical
Max
Unit
Supply Voltage (1.8V)
Vcc2
1.71
1.8
1.89
V
Supply Voltage (3.3V)
Vcc3
3.14
3.3
3.47
V
Supply Voltage (5V)
Vcc5
4.75
5
5.25
V
ICC
-
-
500
mA
Inrush Current (1.8V)
Iinrush2
-
-
1
A
Inrush Current (3.3V)
Iinrush3
-
-
0.75
A
Inrush Current (5V)
Iinrush5
-
-
0.5
A
Total Current on any pin
Module current ramp rate
-
-
100
mA/µS
Power on 1.8V rail
P2rail
-
-
1.8
W
Power on 3.3V rail
P3rail
-
-
2.5
W
Power on 5V rail
P5rail
-
-
2.5
W
Pt
-
-
3.5
W
Power Consumption-P_Down mode
Pp_d
-
-
1.5
W
Power Supply Noise Rejection
PSNR
Module Total Power consumption
Bit Rate
BR
Operating Temperature (case)
Strorage Temperature
LUMINENTOIC.COM
Compliant to Section 2.7.2 of XFP MSA
9.95
-
11.1
Gb/s
Top
-5
-
70
ºC
Tst
-40
-
85
ºC
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
a) Peak to peak noise when measured with a 1 MHz low pass filter
b) Peak to peak noise when measured with 1MHz-10MHz low pass filter
1
LUMNDS643-AUG072007
Rev. 0.2
10 Gbps 120km Multirate XFP Transceiver
Preliminary
XP-MR-D12-CDA
Transmitter Specifications (Optical)
Parameter
Symbol
Min
Typical
Max
Unit
Output Power
PO
-2
0
2
dBm
Average Launch Power Tx_Off
Poff
-
-
-30
nm
Extinction Ratio
ER
8.2
-
-
dB
Eye Mask
ITU-T G.691, Telcordia GR-253-CORE, IEEE802.3 10GBASE-ZR Compliant
Side Mode Suppression Ratio
SMSR
30
λ
∆λ20
1530
-
Jitter Generation (peak-to-peak)
Jgen(pk-pk)
-
Jitter Generation (RMS)
Jgen(RMS)
Wavelength
Spectral Width
Dispersion Penalty at 2000
ps/nma
-
-
dB
1565
nm
-
1
nm
-
0.1
UI
-
-
0.01
UI
DP
-
-
2
dB
Relative Intensity Noise
RIN
-
-
-130
dB/Hz
Reflectance Tolerance
ref T
-
-
-27
dB
a) Using an EDC enabled receiver
Transmitter Specifications (Electrical)
Parameter
Symbol
Min
Typical
Max
Unit
Input Differential Impedence
Rin
-
100
-
Ω
Differential Data Input Swing
Vin,p-p
120
-
820
mV
TxDisable_Disable
Vd
2
-
Vcc3
V
TxDisable_Enable
Ven
GND
-
GND + 0.8
V
Parameter
Symbol
Min
Typical
Max
Unit
Sensitivity (9.95Gb/s)a
Rx sens995
-
-
-24
dBm
(10.7Gb/s)a
Rx sens1070
-
-
-23
dBm
Rx OL
-7
-
-
dBm
nm
Receiver Specifications (Optical)
Sensitivity
Overloada
λ
1528
-
1565
ORL
-
-
-27
dB
LOS Assert
-
-34
-
-
dBm
LOS De-assert
-
-
-
-24
dBm
LOS Hysteresis
-
0.5
-
-
dB
Wavelength
b
Optical Return Loss
a) At 8.2dB ER, 1E-12 BER, 231-1 PRBS, back to back
b) Operational over 1200 - 1625nm range
Receiver Specificatioins (Elelctrical)
Parameter
Symbol
Reference Differential Output Impedence
Differential Data Output Swing
Output Rise Time, 20-80%
Output Fall Time, 20-80%
LOS Fault
LOS Normal
LUMINENTOIC.COM
Min
Typical
Max
Unit
Zd
-
100
-
Ω
Vout,p-p
340
-
850
mV
tr
24
-
-
ps
tf
24
-
-
ps
VLOS_fault
host_Vcc3 - 0.5
-
host_Vcc3
V
VLOS_normal
GND
-
GND + 0.4
V
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS643-AUG072007
Rev. 0.2
10 Gbps 120km Multirate XFP Transceiver
Preliminary
XP-MR-D12-CDA
Reference Clock
Parameter
Symbol
Min
Typical
Max
Unit
Zd
80
100
120
Ω
Differential Input Clock Amplitude (p-p)
640
-
1600
mV
Reference Clock Duty Cycle
40
-
60
%
Clock Differential Input Impedance
Reference Clcok Rise/Fall Time (20%-80%)
Reference Clock Frequency
Tr/Tf
200
-
1250
ps
f0
-
Baud/64
-
MHz
Pin Out Definition
Pin
Logic
1
2
Symbol
Name/Description
Note
GND
Module Ground
1
VEE5
Optional -5.2V Power Supply (not used)
3
LVTTL-I
Mod_DeSel
Module De-select; When held low allows module to respond to 2-wire interface
4
LVTTL-O
Interrupt
Interrupt; Indicates presence of an important condition which can be read over the 2-wire
serial interface
5
LVTTL-I
TX_DIS
Transmitter Disable; Turns off transmitter laser output
6
Vcc5
+5V Power Supply
7
GND
Module Ground
8
Vcc3
+3.3V Power Supply
9
Vcc3
+3.3V Power Supply
2
1
10
LVTTL-I/O
SCL
2-Wire Serial Interface Clock
2
11
LVTTL-I/O
SDA
2-Wire Serial Interface Data Line
2
12
LVTTL-O
Mod_Abs
Indicates Module is not present. Grounded in the Module
2
13
LVTTL-O
Mod_NR
Module Not Ready; Indicating Module Operational Fault
2
14
LVTTL-O
RX_LOS
Receiver Loss Of Signal Indicator
2
15
GND
Module Ground
1
16
GND
Module Ground
1
RD-
Receiver Inverted Data Output
17
CML-O
18
CML-O
RD+
Receiver Non-Inverted Data Output
19
GND
Module Ground
20
Vcc2
+1.8V Power Supply
21
LVTTL-I
P_Down/RST
1
Power Down; When high, requires the module to limit power consumption to 1.5W or
below. 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire serial
interface, equivalent to a power cycle.
22
Vcc2
23
GND
+1.8V Power Supply
Module Ground
1
24
PECL-I
RefCLK+
Reference Clock Non-Inverted Input, AC coupled on the host board
25
PECL-I
RefCLK-
Reference Clock Inverted Input, AC coupled on the host board
GND
Module Ground
1
1
26
27
GND
Module Ground
28
CML-I
TD-
Transmitter Inverted Data Input
29
CML-I
TD+
Transmitter Non-Inverted Data Input
GND
Module Ground
20
1
Notes:
1. Module ground pins GND are isolated from the module case and chassis ground within the module.
2. Shall be pulled up with 4.7k-10kohms to a voltage between 3.15V and 3.45V on the host board.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS643-AUG072007
Rev. 0.2
10 Gbps 120km Multirate XFP Transceiver
Preliminary
XP-MR-D12-CDA
Pinout Diagram
15
GND
T OWARD
ASIC
16
GND
17
RD-
18
RD+
19
GND
20
VCC2
21
P_D OWN/RST
22
VCC2
23
GND
24
R EF CLK+
25
R EF CLK-
26
GND
27
GND
28
TD-
29
TD+
30
GND
RX_LOS
14
MOD_NR
13
MOD_ABS
12
SDA
11
SCL
10
VCC3
9
VCC3
8
GND
7
VCC5
6
TX_DIS
5
INTERR UPT
4
MOD_D E S EL
3
T OWARD
B EZEL
2
VEE5
1
GND
Host PCB XFP Pinout T op View
Mechanical Drawing
6.91
.272
16.15
.636
69.09
2.720
11.47
.451
8.44
.332
3.80
.150
6.02
.237
8.95
.352
12.19
.480
6.25
.246
77.98
3.070
18.29
.720
ISO VIEW
1. LUMINENOIC'S XFP TRANSCEIVERS ARE COMPLIANT WITH THE
DIMENSIONS DEFINED BY XFP MULTISOURCING AGREEMENT (MSA).
NOTES: UNLESS OTHERWISE SPECIFIED
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS643-AUG072007
Rev. 0.2
10 Gbps 120km Multirate XFP Transceiver
Preliminary
XP-MR-D12-CDA
Ordering Information
Part Numbering Definition:
XP -MR-
Reach
- Temperature
Diagnostic
Revision
XP = XFP
MR = Multi-Rate
D12 = 120km
with EDC
C = Commerical Temp
(-5 to 70C)
D = Digital Diagnostic
A = Design Revision
Warnings
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notice
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS643-AUG072007
Rev. 0.2