SST SST49LF004B_10

4 Mbit Firmware Hub
SST49LF004B
SST49LF002B / 003B / 004B4Mb Firmware Hub
EOL Data Sheet
FEATURES:
• 4 Mbit SuperFlash memory array for code/data
storage
– SST49LF004B: 512K x8 (4 Mbit)
• Conforms to Intel LPC Interface Specification
– Supports Single-Byte Firmware Memory
Cycle Type
• Flexible Erase Capability
– Uniform 4 KByte sectors
– Uniform 64 KByte overlay blocks
– Chip-Erase for PP Mode Only
• Single 3.0-3.6V Read and Write Operations
• Superior Reliability
– Endurance: 100,000 Cycles (typical)
– Greater than 100 years Data Retention
• Low Power Consumption
– Active Read Current: 6 mA (typical)
– Standby Current: 10 µA (typical)
• Fast Sector-Erase/Byte-Program Operation
– Sector-Erase Time: 18 ms (typical)
– Block-Erase Time: 18 ms (typical)
– Chip-Erase Time: 70 ms (typical)
– Byte-Program Time: 14 µs (typical)
– Chip Rewrite Time: 8 seconds (typical)
– Single-pulse Program or Erase
– Internal timing generation
• CMOS and PCI I/O Compatibility
• Two Operational Modes
– Low Pin Count (LPC) interface mode for
in-system operation
– Parallel Programming (PP) mode for fast
production programming
• Low Pin Count (LPC) Interface Mode
– LPC bus interface supporting byte Read and
Write
– 33 MHz clock frequency operation
– WP# and TBL# pins provide hardware write
protect for entire chip and/or top Boot Block
– Block Locking Registers for individual block
Write-Lock and Lock-Down protection
– JEDEC Standard SDP Command Set
– Data# Polling and Toggle Bit for End-of-Write
detection
– 5 GPI pins for system design flexibility
– 4 ID pins for multi-chip selection
• Parallel Programming (PP) Mode
– 11-pin multiplexed address and 8-pin data
I/O interface
– Supports fast In-System or PROM programming
for manufacturing
• Packages Available
– 32-lead PLCC
– 32-lead TSOP (8mm x 14mm)
• All non-Pb (lead-free) devices are RoHS compliant
PRODUCT DESCRIPTION
The SST49LF004B flash memory devices are designed to
interface with host controllers (chipsets) that support a lowpin-count (LPC) interface for BIOS applications. The
SST49LF004B devices comply with Intel’s LPC Interface
Specification, supporting single-byte Firmware Memory
cycle type.
The SST49LF004B devices are backward compatible to
the SST49LF004A Firmware Hub. In this document, FWH
mode in the SST49LF004A specification is referenced as
the Firmware Memory Read/Write cycle. Two interface
modes are supported by the SST49LF004B: LPC mode
(Firmware Memory cycle types) for in-system operations
and Parallel Programming (PP) mode to interface with programming equipment.
The SST49LF004B flash memory devices are manufactured with SST’s proprietary, high-performance SuperFlash
technology. The split-gate cell design and thick-oxide tunneling injector attain greater reliability and manufacturability
compared
with
alternative
approaches.
The
SST49LF004B devices significantly improve performance
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
12/07
1
and reliability, while lowering power consumption. The
SST49LF004B devices write (Program or Erase) with a
single 3.0-3.6V power supply.
The SST49LF004B use less energy during Erase and Program than alternative flash memory technologies. The total
energy consumed is a function of the applied voltage, current and time of application. Since for any given voltage
range the SuperFlash technology uses less current to program and has a shorter erase time, the total energy consumed during any Erase or Program operation is less than
alternative flash memory technologies.
The SuperFlash technology provides fixed Erase and Program times, independent of the number of Erase/Program
cycles that have occurred. This means the system software
or hardware does not have to be calibrated or correlated to
the cumulative number of Erase cycles as is necessary
with alternative flash memory technologies, whose Erase
and Program times increase with accumulated Erase/Program cycles.
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
Intel is a registered trademark of Intel Corporation.
These specifications are subject to change without notice.
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
The SST49LF004B devices provide a maximum Byte-Program time of 20 µsec. The entire memory can be erased
and programmed byte-by-byte typically in 8 seconds for the
SST49LF004B device, when using status detection features such as Toggle Bit or Data# Polling to indicate the
completion of Program operation. To protect against inadvertent writes, the SST49LF004B device employ on-chip
hardware and software data protection (SDP) schemes. It
is offered with a typical endurance of 100,000 cycles. Data
retention is rated at greater than 100 years.
To meet high density, surface mount requirements, the
SST49LF004B is offered in both 32-lead PLCC and 32lead TSOP packages. In addition, SST provides lead-free
(non-Pb) package options to address the growing need for
non-Pb solutions in electronic components. Non-Pb package version can be obtained by ordering products with a
package code suffix of “E” as the environmental attribute in
the product part number. See Figures 1 and 2 for pin
assignments and Table 1 for pin descriptions.
TABLE OF CONTENTS
PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LIST OF TABLES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FUNCTIONAL BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PIN ASSIGNMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Input/Output Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Input Communication Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interface Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Identification Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General Purpose Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Write Protect / Top Block Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Row / Column Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Output Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Write Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
No Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DEVICE MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DESIGN CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MODE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
2
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
LPC MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Device Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Firmware Memory Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Firmware Memory Write Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Abort Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Response to Invalid Fields for Firmware Memory Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Multiple Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Write Operation Status Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PARALLEL PROGRAMMING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Device Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Write Operation Status Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Data Protection (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SOFTWARE COMMAND SEQUENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AC Characteristics (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
AC Characteristics (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PRODUCT ORDERING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PACKAGING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
3
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
LIST OF FIGURES
FIGURE 1: Pin Assignments for 32-lead PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIGURE 2: Pin Assignments for 32-lead TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIGURE 3: Device Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
FIGURE 4: Firmware Memory Read Cycle Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIGURE 5: Firmware Memory Write Cycle Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FIGURE 6: LCLK Waveform (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FIGURE 7: Output Timing Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FIGURE 8: Input Timing Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FIGURE 9: Reset Timing Diagram (LPC MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
FIGURE 10: Reset Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
FIGURE 11: Read Cycle Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FIGURE 12: Write Cycle Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FIGURE 13: Data# Polling Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
FIGURE 14: Toggle Bit Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
FIGURE 15: Byte-Program Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FIGURE 16: Sector-Erase Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FIGURE 17: Block-Erase Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
FIGURE 18: Chip-Erase Timing Diagram (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
FIGURE 19: Software ID Entry and Read (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FIGURE 20: Software ID Exit (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FIGURE 21: AC Input/Output Reference Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
FIGURE 22: A Test Load Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
4
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
LIST OF TABLES
TABLE 1: Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TABLE 2: Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TABLE 3: Firmware Memory Cycles START Field Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TABLE 4: Firmware Memory Read Cycle Field Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TABLE 5: Firmware Memory Write Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TABLE 6: Firmware Memory Multiple Device Selection Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TABLE 7: Block Locking Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TABLE 8: Block Locking Register Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TABLE 9: Operation Modes Selection (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TABLE 10: Software Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TABLE 11: DC Operating Characteristics (All Interfaces) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TABLE 12: Recommended System Power-up Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TABLE 13: Pin Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TABLE 14: Reliability Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TABLE 15: Clock Timing Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TABLE 16: Read/Write Cycle Timing Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TABLE 17: AC Input/Output Specifications (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TABLE 18: Interface Measurement Condition Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TABLE 19: Reset Timing Parameters (LPC Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TABLE 20: Reset Timing Parameters (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
TABLE 21: Read Cycle Timing Parameters (PP Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
TABLE 22: Program/Erase Cycle Timing Parameters (PP Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
TABLE 23: Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
5
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
FUNCTIONAL BLOCKS
FUNCTIONAL BLOCK DIAGRAM
TBL#
WP#
INIT#
X-Decoder
SuperFlash
Memory
LAD[3:0]
LCLK
LFRAME#
LPC
Interface
Address Buffers & Latches
Y-Decoder
ID[3:0]
GPI[4:0]
R/C#
A[10:0]
DQ[7:0]
OE#
WE#
Control Logic
I/O Buffers and Data Latches
Programmer
Interface
MODE RST#
©2007 Silicon Storage Technology, Inc.
1307 B1.0
S71307-03-EOL
6
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
NC
2
1
A10 (GPI4)
RST# (RST#)
3
R/C# (LCLK)
A9 (GPI3)
4
VDD (VDD)
A8 (GPI2)
PIN ASSIGNMENTS
32 31 30
29
A7(GPI1)
5
A6 (GPI0)
6
28
VSS (VSS)
A5 (WP#)
7
27
NC
A4 (TBL#)
8
26
NC
A3 (ID3)
9
25
VDD (VDD)
A2 (ID2)
10
24
OE# (INIT#)
A1 (ID1)
11
23
WE# (LFRAME#)
A0 (ID0)
12
22
NC
DQ0 (LAD0)
13
21
14 15 16 17 18 19 20
( ) Designates LPC Mode
DQ7 (RES)
DQ6 (RES)
DQ5 (RES)
DQ4 (RES)
DQ3 (LAD3)
VSS (VSS)
DQ2 (LAD2)
DQ1 (LAD1)
32-lead PLCC
Top View
MODE (MODE)
1307 32-plcc P1.0
FIGURE 1: PIN ASSIGNMENTS FOR 32-LEAD PLCC
NC
NC
NC
VSS (VSS)
MODE (MODE)
A10 (FGPI4)
R/C# (CLK)
VDD (VDD)
NC
RST# (RST#)
A9 (FGPI3)
A8 (FGPI2)
A7 (FGPI1)
A6 (FGPI0)
A5 (WP#)
A4 (TBL#)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Standard Pinout
Top View
Die Up
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE# (INIT#)
WE# (LFRAME#)
VDD (VDD)
DQ7 (RES)
DQ6 (RES)
DQ5 (RES)
DQ4 (RES)
DQ3 (LAD3)
VSS (VSS)
DQ2 (LAD2)
DQ1 (LAD1)
DQ0 (LAD0)
A0 (ID0)
A1 (ID1)
A2 (ID2)
A3 (ID3)
1307 32-tsop WH P1.0
( ) Designates LPC Mode
FIGURE 2: PIN ASSIGNMENTS FOR 32-LEAD TSOP
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
7
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
PIN DESCRIPTIONS
TABLE 1: PIN DESCRIPTION
Interface
Symbol
Pin Name
LCLK
Clock
LAD[3:0]
Address and
Data
Type1
PP
LPC
Functions
I
X
To provide a clock input to the control unit.
The clock conforms to the PCI specification.
I/O
X
To provide LPC bus information such as addresses and command
inputs/outputs to memory.
LFRAME# Frame
I
X
To indicate start of a data transfer operation; also used to abort an LPC cycle in
progress.
MODE
Interface
Mode Select
I
X
X
This pin determines which interface is operational. When held high, programmer
mode is enabled and when held low, LPC mode is enabled. This pin must be set at
power-up or before returning from reset and must not change during device operation. This pin must be held high (VIH) for PP mode and low (VIL) for LPC mode. This
pin is internally pulled-down with a resistor between 20-100 KΩ.
RST#
Reset
I
X
X
To reset the operation of the device
INIT#
Initialize
I
X
This is the second reset pin for in-system use.
This pin functions identically to RST#.
ID[3:0]
Identification
Inputs
I
X
These four pins are part of the mechanism that allows multiple parts to be attached
to the same bus. The strapping of these pins is used to identify the component. The
boot device must have ID[3:0]=0000, all subsequent devices should use sequential
count-up strapping. These pins are internally pulled-down with a resistor between
20-100 KΩ.
GPI[4:0]
General
Purpose Inputs
I
X
These individual inputs can be used for additional board flexibility. The state of these
pins can be read through GPI_REG (General Purpose Inputs Register). These
inputs should be at their desired state before the start of the LPC clock cycle during
which the read is attempted, and should remain in place until the end of the Read
cycle. Unused GPI pins must not be floated.
TBL#
Top Block Lock
I
X
When low, prevents programming to the boot block sectors at the top of the device
memory. When TBL# is high it disables hardware write protection for the top block
sectors. This pin cannot be left unconnected.
WP#
Write Protect
I
X
When low, prevents programming to all but the highest addressable blocks. When
WP# is high it disables hardware write protection for these blocks. This pin cannot be
left unconnected.
R/C#
Row/Column
Select
I
X
Select for the Programming interface, this pin determines whether the address pins
are pointing to the row addresses, or to the column addresses.
A10-A0
Address
I
X
Inputs for low-order addresses during Read and Write operations. Addresses are
internally latched during a Write cycle. For the programming interface, these
addresses are latched by R/C# and share the same pins as the high-order address
inputs.
DQ7-DQ0
Data
I/O
X
To output data during Read cycles and receive input data during Write cycles. Data is
internally latched during a Write cycle.
The outputs are in tri-state when OE# is high.
OE#
Output Enable
I
X
To gate the data output buffers.
WE#
Write Enable
I
X
To control the Write operations.
RES
Reserved
VDD
Power Supply
PWR
VSS
Ground
PWR
NC
No Connection
X
These pins must be left unconnected.
X
X
To provide power supply (3.0-3.6V)
X
X
Circuit ground (0V reference)
N/A
N/A
Unconnected pins.
T1.2 1307
1. I = Input, O = Output
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
8
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Clock
General Purpose Inputs
The LCLK pin accepts a clock input from the host controller.
The General Purpose Inputs (GPI[4:0]) can be used as digital inputs for the CPU to read. The GPI register holds the
values on these pins. The data on the GPI pins must be
stable before the start of a GPI register Read and remain
stable until the Read cycle is complete. The pins must be
driven low, VIL, or high, VIH but not left unconnected (float).
Input/Output Communications
The LAD[3:0] pins are used to serially communicate cycle
information such as cycle type, cycle direction, ID selection,
address, data, and sync fields.
Write Protect / Top Block Lock
Input Communication Frame
The Top Boot Lock (TBL#) and Write Protect (WP#) pins
are provided for hardware write protection of device memory in the SST49LF004B. The TBL# pin is used to write
protect 16 boot sectors (64 KByte) at the highest memory
address range for the SST49LF004B. The WP# pin write
protects the remaining sectors in the flash memory.
The LFRAME# pin is used to indicate start of a LPC bus
cycle. The pin is also used to abort an LPC bus cycle in
progress.
Interface Mode Select
The MODE pin is used to set the interface mode. If the
mode pin is set to logic high, the device is in PP mode. If
the mode pin is set low, the device is in the LPC mode. The
mode selection pin must be configured prior to device operation. The mode pin is internally pulled down if the pin is left
unconnected.
An active low signal at the TBL# pin prevents Program and
Erase operations of the top boot block. When TBL# pin is
held high, the hardware write protection of the top boot
block is disabled. The WP# pin serves the same function for
the remaining blocks of the device memory. The TBL# and
WP# pins write protection functions operate independently
of one another. Both TBL# and WP# pins must be set to
their required protection states prior to starting a Program or
Erase operation. A logic level change occurring at the TBL#
or WP# pin during a Program or Erase operation could
cause unpredictable results.
Reset
A VIL on INIT# or RST# pin initiates a device reset. INIT#
and RST# pins have the same function internally. It is
required to drive INIT# or RST# pins low during a system
reset to ensure proper CPU initialization. During a Read
operation, driving INIT# or RST# pins low deselects the
device and places the output drivers, LAD[3:0], in a high
impedance state. The reset signal must be held low for a
minimum of time TRSTP. A reset latency occurs if a reset procedure is performed during a Program or Erase operation.
See Tables 19 and 20, Reset Timing Parameters, for more
information. A device reset during an active Program or
Erase operation will abort the operation and memory contents may become invalid due to data being altered or corrupted from an incomplete Erase or Program operation.
Row / Column Select
The R/C# pin is used to control the multiplex address
inputs in Parallel Programming (PP) mode. The column
addresses are mapped to the higher internal address
(A18-11), and the row addresses are mapped to the lower
internal addresses (A10-0).
Output Enable
The OE# pin is used to gate the output data buffers in PP
mode.
Identification Inputs
Write Enable
These pins are part of a mechanism that allows multiple
devices to be attached to the same bus. The strapping of
these pins is used to identify the component. The boot
device must have ID[3:0] = 0; all subsequent devices
should use sequential count-up strapping. These pins are
internally pulled-down with a resistor between 20-100 KΩ.
The WE# pin is used to control the write operations in PP
mode.
No Connection
These pins are not connected internally.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
9
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
DEVICE MEMORY MAP
TBL#
7FFFFH
Boot Block
Block 7
70000H
6FFFFH
Block 6
60000H
5FFFFH
Block 5
50000H
4FFFFH
Block 4
40000H
3FFFFH
Block 3
30000H
2FFFFH
WP#
Block 0-6
Block 2
20000H
1FFFFH
Block 1
10000H
0F000H
Block 0
(64 KByte)
02000H
01000H
00000H
4 KByte Sector 2
4 KByte Sector 1
4 KByte Sector 0
1307 F02.0
FIGURE 3: DEVICE MEMORY MAP
DESIGN CONSIDERATIONS
PRODUCT IDENTIFICATION
SST recommends a high frequency 0.1 µF ceramic capacitor to be placed as close as possible between VDD and
VSS less than 1 cm away from the VDD pin of the device.
Additionally, a low frequency 4.7 µF electrolytic capacitor
from VDD to VSS should be placed within 1 cm of the VDD
pin. If a socket is used for programming purposes, an additional 1-10 µF should be added next to each socket.
The Product Identification mode identifies the device as the
SST49LF004B and manufacturer as SST.
TABLE 2: PRODUCT IDENTIFICATION
Address
PP Mode
Manufacturer’s ID
The RST# and INIT# pins must remain stable at VIH for the
entire duration of an Erase or Program operation. WP#
must remain stable at VIH for the entire duration of the
Erase and Program operations for non-Boot Block sectors.
To write data to the top Boot Block sectors, the TBL# pin
must also remain stable at VIH for the entire duration of the
Erase and Program operations.
Device
LPC
Data
Mode1
0000H
FFBC 0000H
0001H
FFBC 0001H
BFH
ID2
SST49LF004B
60H
T2.0 1307
1. Address shown in this column is for boot device only.
Address locations should appear elsewhere in the 4
GByte system memory map depending on ID strapping
values on ID[3:0] pins when multiple LPC memory
devices are used in a system.
2. The device ID for SST49LF004B is the same as
SST49LF004A.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
10
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
MODE SELECTION
LPC MODE
The SST49LF004B flash memory device operates in two
distinct interface modes: the LPC mode and the Parallel
Programming (PP) mode. The MODE (Interface Mode
Select) pin is used to set the interface mode selection. If the
MODE pin is set to logic high, the device is in PP mode;
while if the MODE pin is set low, the device is in LPC mode.
The MODE selection pin must be configured prior to device
operation and must not change during operation. If the pin
is not connected, by default the Mode pin is internally
pulled low and the 49LF00xB will be in LPC operation.
Device Operation
The LPC mode uses a 5-signal communication interface
consisting of one control line, LFRAME#, which is driven by
the host to start or abort a bus cycle, and a 4-bit data bus,
LAD[3:0], which is used to communicate cycle type, cycle
direction, ID selection, address, data and sync fields. The
device enters standby mode when LFRAME# is high and
no internal operation is in progress.
The SST49LF004B supports single-byte Firmware Memory Read/Write cycles as defined in Intel’s Low-Pin-Count
Interface Specification. The host drives LFRAME# low for
one or more clock cycles to initiate an LPC cycle. The last
latched value of LAD[3:0] before LFRAME# is the START
value. The START value determines whether the
SST49LF004B will respond to a Firmware Memory Read
or Firmware Memory Write cycle as defined in Table 3.
In LPC mode, communication between the Host and the
SST49LF004B occurs via the 4-bit I/O communication signals, LAD[3:0] and LFRAME#. The SST49LF004B detects
whether it is being accessed via a FWH Read or FWH
Write cycle by detecting the START field contents; 91101b
is a FWH read cycle and a 1110b indicates a FWH Write
cycle.
In PP mode, the device is controlled via the 11 addresses,
A10-A0, and 8 I/O, DQ7-DQ0, signals. The address inputs
are multiplexed in row and column selected by control signal R/C# pin. The row addresses are mapped to the lower
internal addresses (A10-0), and the column addresses are
mapped to the higher internal addresses (A18-11). See Figure 3, Device Memory Map, for address assignments.
TABLE 3: FIRMWARE MEMORY CYCLES START
FIELD DEFINITION
START
Value Definition
1101
Start of a Firmware Memory Read cycle
1110
Start of a Firmware Memory Write cycle
T3.0 1307
See following sections for details of Firmware Memory
cycle types. JEDEC standard SDP (Software Data Protection) Program and Erase command sequences are used
to initiate Firmware Memory Program and Erase operations. See Table 9 for a listing of Program and Erase commands. Chip-Erase is only available in PP mode.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
11
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Firmware Memory Read Cycle
TABLE 4: FIRMWARE MEMORY READ CYCLE FIELD DEFINITIONS
Clock
Cycle
Field
Name
Field Contents
LAD[3:0]1
LAD[3:0]
Direction
1
START
1101
IN
LFRAME# must be active (low) for the device to respond.
Only the last field latched before LFRAME# transitions high
will be recognized. The START field contents (1101b) indicate a Firmware Memory Read cycle.
2
IDSEL
0000 to 1111
IN
Indicates which SST49LF004B device should respond. If the
IDSEL (ID select) field matches the value of ID[3:0], the device
will respond to the LPC bus cycle.
3-9
MADDR
YYYY
IN
These seven clock cycles make up the 28-bit memory
address. YYYY is one nibble of the entire address.
Addresses are transferred most-significant nibble first.
10
MSIZE
0000 (1 Byte)
IN
The MSIZE field indicates how many bytes will be transferred during multi-byte operations. The SST49LF004B
only supports single-byte operation. MSIZE=0000b
11
TAR0
1111
IN then Float
12
TAR1
1111 (float)
Float then
OUT
13
RSYNC
0000 (READY)
OUT
During this clock cycle, the device generates a “ready sync”
(RSYNC) indicating that the device has received the input
data.
14
DATA
ZZZZ
OUT
ZZZZ is the least-significant nibble of the data byte.
15
DATA
ZZZZ
OUT
ZZZZ is the most-significant nibble of the data byte.
16
TAR0
1111
OUT then
Float
17
TAR1
1111 (float)
Float then IN
Comments
In this clock cycle, the master has driven the bus to all ‘1’s
and then floats the bus, prior to the next clock cycle. This is
the first part of the bus “turnaround cycle.”
The SST49LF004B takes control of the bus during this
cycle.
In this clock cycle, the SST49LF004B drives the bus to all
ones and then floats the bus prior to the next clock cycle.
This is the first part of the bus “turnaround cycle.”
The host resumes control of the bus during this cycle.
T4.1 1307
1. Field contents are valid on the rising edge of the present clock cycle.
LCLK
LFRAME#
LAD[3:0]
Start
IDSEL
1101b
0000b
MADDR
A[27:24] A[23:20] A[19:16] A[15:12] A[11:8]
A[7:4]
A[3:0]
MSIZE
TAR0
TAR1
RSYNC
0000b
1111b
Tri-State
0000b
DATA
D[3:0]
D[7:4]
TAR
1307 F03.0
FIGURE 4: FIRMWARE MEMORY READ CYCLE WAVEFORM
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
12
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Firmware Memory Write Cycle
TABLE 5: FIRMWARE MEMORY WRITE CYCLE
Clock
Cycle
Field
Name
Field Contents
LAD[3:0]1
LAD[3:0]
Direction
1
START
1110
IN
LFRAME# must be active (low) for the device to
respond. Only the last field latched before LFRAME#
transitions high will be recognized. The START field
contents (1110b) indicate a Firmware Memory Write
cycle.
2
IDSEL
0000 to 1111
IN
Indicates which SST49LF004B device should
respond. If the IDSEL (ID select) field matches the
value of ID[3:0], the device will respond to the memory cycle.
3-9
MADDR
YYYY
IN
These seven clock cycles make up the 28-bit memory
address. YYYY is one nibble of the entire address.
Addresses are transferred most-significant nibble first.
10
MSIZE
0000 (1 Byte)
IN
The MSIZE field indicates how many bytes will be
transferred during multi-byte operations. The device
only supports single-byte writes. MSIZE=0000b
11
DATA
ZZZZ
IN
ZZZZ is the least-significant nibble of the data byte.
ZZZZ is the most-significant nibble of the data byte.
Comments
12
DATA
ZZZZ
IN
13
TAR0
1111
IN then Float
In this clock cycle, the host drives the bus to all '1's and
then floats the bus prior to the next clock cycle. This is
the first part of the bus “turnaround cycle.”
14
TAR1
1111 (float)
Float then OUT
The SST49LF004B takes control of the bus during this
cycle.
15
RSYNC
0000
OUT
During this clock cycle, the device generates a “ready
sync” (RSYNC) indicating that the device has received
the input data.
16
TAR0
1111
OUT then Float
In this clock cycle, the SST49LF004B drives the bus to
all '1's and then floats the bus prior to the next clock
cycle. This is the first part of the bus “turnaround cycle.”
17
TAR1
1111 (float)
Float then IN
The host resumes control of the bus during this cycle.
T5.0 1307
1. Field contents are valid on the rising edge of the present clock cycle.
LCLK
LFRAME#
LAD[3:0]
Start
IDSEL
1110b
0000b
MADDR
MSIZE
A[27:24] A[23:20] A[19:16] A[15:12] A[11:8]
A[7:4]
A[3:0]
0000b
DATA
D[3:0]
D[7:4]
TAR0
TAR1
RSYNC
1111b
Tri-State
0000b
TAR
1307 F04.0
FIGURE 5: FIRMWARE MEMORY WRITE CYCLE WAVEFORM
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
13
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Abort Mechanism
Multiple Device Selection
If LFRAME# is driven low for one or more clock cycles after
the start of a bus cycle, the cycle will be terminated. The
host may drive LAD[3:0] with '1111b' (ABORT nibble) to
return the interface to ready mode. The ABORT only
affects the current bus cycle. For a multi-cycle command
sequence, such as the Erase or Program SDP commands,
ABORT doesn't interrupt the entire command sequence,
only the current bus cycle of the command sequence. The
host can re-send the bus cycle for the aborted command
and continue the SDP command sequence after the device
is ready again.
Multiple LPC flash devices may be strapped to increase
memory densities in a system. The four ID pins, ID[3:0],
allow up to 16 devices to be attached to the same bus by
using different ID strapping in a system. BIOS support, bus
loading, or the attaching bridge may limit this number. The
boot device must have an ID of 0000b (determined by
ID[3:0]); subsequent devices use incremental numbering.
Equal density must be used with multiple devices.
Multiple Device Selection for
Firmware Memory Cycle
For Firmware Memory Read/Write cycles, hardware strapping values on ID[3:0] must match the values in IDSEL
field. See Table 6 for multiple device selection configurations. The SST49LF004B will compare the IDSEL field with
ID[3:0]'s strapping values. If there is a mismatch, the device
will ignore the reminder of the cycle.
Response to Invalid Fields for Firmware
Memory Cycle
During LPC operations the SST49LF004B will not explicitly
indicate that it has received invalid field sequences. The
response to specific invalid fields or sequences is as follows:
TABLE 6: FIRMWARE MEMORY MULTIPLE DEVICE
SELECTION CONFIGURATION
ID mismatch: If the IDSEL field does not match ID[3:0],
the device will ignore the cycle. See Multiple Device Selection section for details.
Device #
Address out of range: The address sequence is 7
fields long (28 bits) for Firmware Memory bus cycles, but
only A22 and A18:A0 will be decoded by SST49LF004B.
Address A22 has the special function of directing reads and
writes to the flash core (A22=1) or to the register space
(A22=0).
Invalid MSIZE field If the device receives an invalid
MSIZE field during a Firmware Memory Read or Write
cycle, the cycle will be ignored and no operation will be
attempted. The SST49LF004B will not generate any kind
of response in this situation. Invalid size fields for a Firmware Memory cycle are any data other than 0000b.
Once valid START, IDSEL, and MSIZE fields are received,
the SST49LF004B will always complete the bus cycle.
However, if the device is busy performing a flash Erase or
Program operation, no new Write command (memory write
or register write) will be executed.
ID[3:0]
IDSEL
0 (Boot device)
0000
0000
1
0001
0001
2
0010
0010
3
0011
0011
4
0100
0100
5
0101
0101
6
0110
0110
7
0111
0111
8
1000
1000
9
1001
1001
10
1010
1010
11
1011
1011
12
1100
1100
13
1101
1101
14
1110
1110
15
1111
1111
T6.0 1307
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
14
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Write Operation Status Detection
Registers
The SST49LF004B device provides two software means to
detect the completion of a Write (Program or Erase) cycle,
in order to optimize the system Write cycle time. The software detection includes two status bits: Data# Polling, DQ7,
and Toggle Bit, DQ6. The End-of-Write detection mode is
incorporated into the Firmware Memory Read cycles. The
actual completion of the nonvolatile write is asynchronous
with the system. Therefore, either a Data# Polling or Toggle
Bit read may be simultaneous with the completion of the
Write cycle. If this occurs, the system may possibly get an
erroneous result, i.e., valid data may appear to conflict with
either DQ7 or DQ6. In order to prevent spurious rejection, if
an erroneous result occurs, the software routine should
include a loop to read the accessed location an additional
two (2) times. If both reads are valid, then the device has
completed the Write cycle, otherwise the rejection is valid.
There are three types of registers available on the
SST49LF004B, the General Purpose Inputs register, Block
Locking registers, and the JEDEC ID registers. These registers appear at their respective address location in the 4
GByte system memory map. Unused register locations will
read as 00H. Any attempt to read or write any register during an internal Write operation will be ignored.
General Purpose Inputs Register
The GPI_REG (General Purpose Inputs Register) passes
the state of GPI[4:0] to the outputs. It is recommended that
the GPI[4:0] pins are in the desired state before LFRAME#
is brought low for the beginning of the bus cycle, and remain
in that state until the end of the cycle. There is no default
value since this is a pass-through register. The GPI register
for the boot device appears at FFBC0100H in the 4 GByte
system memory map, and will appear elsewhere if the
device is not the boot device. The register is not available to
be read when the device is in Erase/Program operation.
Data# Polling
When the SST49LF004B device is in the internal Program
operation, any attempt to read DQ7 will produce the complement of the true data. Once the Program operation is
completed, DQ7 will produce true data. Note that even
though DQ7 may have valid data immediately following the
completion of an internal Write operation, the remaining
data outputs may still be invalid. Valid data will appear on
the entire data bus in subsequent successive Read cycles
after an interval of 1 µs. During an internal Erase operation,
any attempt to read DQ7 will produce a '0'. Once the internal Erase operation is completed, DQ7 will produce a '1'.
Proper status will not be given using Data# Polling if the
address is in the invalid range.
Block Locking Registers
SST49LF004B provides software controlled lock protection
through a set of Block Locking registers. The Block Locking
registers are Read/Write registers and are accessible
through standard addressable memory locations specified
in Table 7 for boot device. These registers will appear elsewhere if the device is not the boot device. Unused register
locations will read as 00H.
Write Lock: The Write-Lock bit, bit 0, controls the lock
state. The default Write status of all blocks after power up is
write locked. When bit 0 of the Block Locking register is set,
Program and Erase operations for the corresponding block
are prevented. Clearing the Write-Lock bit will unprotect the
block. The Write-Lock bit must be cleared prior to starting a
Program or Erase operation since it is sampled at the
beginning of the operation.
Toggle Bit
During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating 0s and
1s, i.e., toggling between 0 and 1. When the internal Program or Erase operation is completed, the toggling will stop.
Note that even though DQ6 may have valid data immediately
following the completion of an internal Write operation, the
remaining data outputs may still be invalid. Valid data will
appear on the entire data bus in subsequent successive
Read cycles after an interval of 1 µs. Proper status will not be
given using Toggle Bit if the address is in the invalid range.
The Write-Lock bit functions in conjunction with the hardware Write Lock pin TBL# for the top Boot Block. When
TBL# is low, it overrides the software locking scheme. The
top Boot Block Locking register does not indicate the state
of the TBL# pin.
The Write-Lock bit functions in conjunction with the hardware WP# pin for blocks 0 to 6. When WP# is low, it overrides the software locking scheme. The Block Locking
registers do not indicate the state of the WP# pin.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
15
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Lock Down: The Lock-Down bit, bit 1, controls the
Block Locking registers. The default Lock Down status of
all blocks upon power-up is not locked down. Once the
Lock-Down bit is set, any future attempted changes to
that Block Locking register will be ignored. The LockDown bit is only cleared upon a device reset with RST# or
INIT# or power down. Current Lock Down status of a particular block can be determined by reading the corresponding Lock-Down bit.
Once the Lock-Down bit of a block is set, the Write-Lock
bits for that block can no longer be modified, and the block
is locked down in its current state of write accessibility.
TABLE 7: BLOCK LOCKING REGISTERS1
Register
Protected Memory
Address Range
Block Size
Memory Map
Register Address
T_BLOCK_LK
64K
07FFFFH - 070000H
FFBF0002H
T_MINUS01_LK
64K
06FFFFH - 060000H
FFBE0002H
T_MINUS02_LK
64K
05FFFFH - 050000H
FFBD0002H
T_MINUS03_LK
64K
04FFFFH - 040000H
FFBC0002H
T_MINUS04_LK
64K
03FFFFH - 030000H
FFBB0002H
T_MINUS05_LK
64K
02FFFFH - 020000H
FFBA0002H
T_MINUS06_LK
64K
01FFFFH - 010000H
FFB90002H
T_MINUS07_LK
64K
00FFFFH - 000000H
FFB80002H
T7.0 1307
1. Default value at power up is 01H
TABLE 8: BLOCK LOCKING REGISTER BITS
Reserved Bit [7..2]
000000
000000
000000
000000
Lock-Down Bit [1]
0
0
1
1
Write-Lock Bit [0]
0
1
0
1
Lock Status
Full Access
Write Locked (Default State at Power-Up)
Locked Open (Full Access Locked Down)
Write Locked Down
T8.0 1307
JEDEC ID Registers
The JEDEC ID registers provide access to the manufacturer and device ID information with a single Read cycle.
The JEDEC ID registers for the boot device appear at
FFBC0000H and FFBC0001H in the 4 GByte system
memory map, and will appear elsewhere if the device is not
the boot device. Registers are not available for read when
the device is in Erase/Program operation. Unused register
location will read as 00H. Refer to Table 2 for product identification information.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
16
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
PARALLEL PROGRAMMING MODE
Device Operation
Block-Erase Operation
Commands are used to initiate the memory operation functions of the device. The data portion of the software command sequence is latched on the rising edge of WE#.
During the software command sequence the row address
is latched on the falling edge of R/C# and the column
address is latched on the rising edge of R/C#.
The Block-Erase operation allows the system to erase the
device in any of the 8 uniform 64 KByte blocks for the
SST49LF004B. The Block-Erase operation is initiated by
executing a six-byte command load sequence for Software
Data Protection with Block-Erase command (50H) and
block address (BA) in the last bus cycle. The internal BlockErase operation begins after the sixth WE# pulse. The
End-of-Erase can be determined using either Data# Polling
or Toggle Bit methods. See Figure 17 for timing waveforms.
Any commands written during the Block- Erase operation
will be ignored.
Read
The Read operation of the SST49LF004B device is controlled by OE#. OE# is the output control and is used to
gate data from the output pins. Refer to the Read cycle timing diagram, Figure 11, for further details.
Chip-Erase Operation
The SST49LF004B device provides a Chip-Erase operation only in PP mode, which allows the user to erase the
entire memory array to the '1's state. This is useful when
the entire device must be quickly erased.
Reset
A VIL on RST# pin initiates a device reset.
Byte-Program Operation
The Chip-Erase operation is initiated by executing a sixbyte Software Data Protection command sequence with
Chip-Erase command (10H) with address 5555H in the last
bus cycle. The internal Erase operation begins with the rising edge of the sixth WE#. During the internal Erase operation, the only valid reads are Toggle Bit or Data# Polling.
See Table 10 for the command sequence, Figure 18 for
timing diagram. Any commands written during the ChipErase operation will be ignored.
The SST49LF004B device is programmed on a byte-bybyte basis. Before programming, one must ensure that the
byte that is being programmed is fully erased. The ByteProgram operation is initiated by executing a four-byte command load sequence for Software Data Protection with
address (PA) and data in the last bus cycle. During the
Byte-Program operation, the row address (A10-A0) is
latched on the falling edge of R/C# and the column
Address (A21-A11) is latched on the rising edge of R/C#.
The data bus is latched on the rising edge of WE#. The
Program operation, once initiated, will be completed, within
20 µs. See Figure 15 for timing waveforms. During the Program operation, the only valid reads are Data# Polling and
Toggle Bit. During the internal Program operation, the host
is free to perform additional tasks. Any commands written
during the internal Program operation will be ignored.
Write Operation Status Detection
The SST49LF004B device provides two software means to
detect the completion of a Write (Program or Erase) cycle,
in order to optimize the system Write cycle time. The software detection includes two status bits: Data# Polling DQ7
and Toggle Bit DQ6. The End-of-Write detection mode is
enabled after the rising edge of WE# which initiates the
internal Program or Erase operation.
Sector-Erase Operation
The Sector-Erase operation allows the system to erase the
device on a sector-by-sector basis. The sector architecture
is based on uniform sector size of 4 KByte. The SectorErase operation is initiated by executing a six-byte command load sequence for Software Data Protection with
Sector-Erase command (30H) and sector address (SA) in
the last bus cycle. The internal Erase operation begins after
the sixth WE# pulse. The End-of-Erase can be determined
using either Data# Polling or Toggle Bit methods. See Figure 16 for Sector-Erase timing waveforms. Any commands
written during the Sector-Erase operation will be ignored.
The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or
Toggle Bit read may be simultaneous with the completion of
the Write cycle. If this occurs, the system may possibly get
an erroneous result, i.e., valid data may appear to conflict
with either DQ7 or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software routine
should include a loop to read the accessed location an additional two (2) times. If both reads are valid, the device has
completed the Write cycle, otherwise the rejection is valid.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
17
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
TABLE 9: OPERATION MODES SELECTION (PP MODE)
Mode
RST#
OE#
WE#
DQ
Address
Read
VIL
VIH
DOUT
AIN
VIH
VIH
VIL
DIN
AIN
Erase
VIH
VIH
VIH
VIL
X1
Sector or Block address,
XXH for Chip-Erase
Reset
VIL
X
X
Write Inhibit
VIH
VIH
VIL
VIH
VIH
Program
Product Identification
VIL
High Z
X
High Z/DOUT
X
Manufacturer’s ID (BFH)
Device ID2
A18 - A1 = VIL, A0 = VIL
A18 - A1 = VIL, A0 = VIH
T9.0 1307
1. X can be VIL or VIH, but no other value.
2. Device ID = 60H for SST49LF004B
Data# Polling DQ7
Data Protection (PP Mode)
When the SST49LF004B device is in the internal Program
operation, any attempt to read DQ7 will produce the complement of the true data. Once the Program operation is
completed, DQ7 will produce true data. Note that even
though DQ7 may have valid data immediately following the
completion of an internal Write operation, the remaining
data outputs may still be invalid. Valid data will appear on
the entire data bus in subsequent successive Read cycles
after an interval of 1 µs. During an internal Erase operation,
any attempt to read DQ7 will produce a '0'. Once the internal Erase operation is completed, DQ7 will produce a '1'.
Data# Polling is valid after the rising edge of the fourth WE#
pulse for the Program operation. For Sector-Erase, BlockErase, or Chip-Erase, the Data# Polling is valid after the rising edge of the sixth WE# pulse. See Figure 13 for Data#
Polling timing diagram. Proper status will not be given using
Data# Polling if the address is in the invalid range.
The SST49LF004B device provides both hardware and
software features to protect nonvolatile data from inadvertent writes.
Hardware Data Protection
Noise/Glitch Protection: A WE# pulse of less than 5 ns will
not initiate a Write cycle.
VDD Power Up/Down Detection: The Write operation is
inhibited when VDD is less than 1.5V.
Write Inhibit Mode: Forcing OE# low, WE# high will inhibit
the Write operation. This prevents inadvertent writes during
power-up or power-down.
Software Data Protection (SDP)
The SST49LF004B provides the JEDEC approved Software Data Protection scheme for all data alteration operation, i.e., Program and Erase. Any Program operation
requires the inclusion of a series of three-byte sequence.
The three-byte load sequence is used to initiate the Program operation, providing optimal protection from inadvertent Write operations, e.g., during the system power-up or
power down. Any Erase operation requires the inclusion of
a five-byte load sequence.
Toggle Bit DQ6
During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating '0's
and '1's, i.e., toggling between 0 and 1. When the internal
Program or Erase operation is completed, the toggling will
stop. The device is then ready for the next operation. The
Toggle Bit is valid after the rising edge of the fourth WE#
pulse for Program operation. For Sector-Erase, BlockErase or Chip-Erase, the Toggle Bit is valid after the rising
edge of the sixth WE# pulse. See Figure 14 for Toggle Bit
timing diagram.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
18
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
SOFTWARE COMMAND SEQUENCE
TABLE 10: SOFTWARE COMMAND SEQUENCE
Command
Sequence
1st1
Cycle
Addr2
2nd1
Cycle
Data
Addr2
3rd1
Cycle
Data
Addr2
4th1
Cycle
5th1
Cycle
Data
Addr2
Data
Data
AAH
Byte-Program
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
A0H
PA3
Sector-Erase
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
80H
YYYY 5555H
6th1
Cycle
Addr2
Data
Addr2
Data
YYYY 2AAAH
55H
SAX4
30H
5
Block-Erase
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
80H
YYYY 5555H
AAH
YYYY 2AAAH
55H
BAX
50H
Chip-Erase6
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
80H
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
10H
Software
ID Entry7,8
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
90H
Software
ID Exit9
XXXX XXXXH
F0H
Software
ID Exit9
YYYY 5555H
AAH
YYYY 2AAAH
55H
YYYY 5555H
F0H
Read ID
T10.0 1307
1. LPC mode use consecutive Write cycles to complete a command sequence; PP mode use consecutive bus cycles to complete a
command sequence.
2. YYYY = A[31:16]. In LPC mode, during SDP command sequence, YYYY must be within valid memory address range, see Address
out of range section for details. In PP mode, YYYY can be VIL or VIH, but no other value.
3. PA = Program Byte address
4. SAX for Sector-Erase Address
5. BAX for Block-Erase Address
6. Chip-Erase is supported in PP mode only
7. SST Manufacturer’s ID = BFH, is read with A18-A0 = 0.
With A18-A1 = 0; 49LF004B Device ID = 60H, is read with A0 = 1.
8. The device does not remain in Software Product ID mode if powered down.
9. Both Software ID Exit operations are equivalent
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
19
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
ELECTRICAL SPECIFICATIONS
The AC and DC specifications for the LPC interface signals (LA0[3:0], LFRAME, LCLCK and RST#) are defined in Section 4.2.2.4 of the PCI local bus specification, Rev. 2.1. Refer to Table 11 for the DC voltage and current specifications.
Refer to Tables 16 through 22 for the AC timing specifications for Clock, Read, Write, and Reset operations.
Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum
Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation
of the device at these conditions or conditions greater than those defined in the operational sections of this data
sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.)
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
D.C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V
Transient Voltage (<20 ns) on Any Pin to Ground Potential1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V to VDD+2.0V
Package Power Dissipation Capability (TA=25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W
Surface Mount Solder Reflow Temperature2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C for 10 seconds
Output Short Circuit Current3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
1. Do not violate processor or chipset limitations on the INIT# pin
2. Excluding certain with-Pb 32-PLCC units, all packages are 260°C capable in both non-Pb and with-Pb solder versions.
Certain with-Pb 32-PLCC package types are capable of 240°C for 10 seconds; please consult the factory for the latest information.
3. Outputs shorted for no more than one second. No more than one output shorted at a time.
OPERATING RANGE
Range
Commercial
Ambient Temp
VDD
0°C to +85°C
3.0-3.6V
AC CONDITIONS OF TEST1
Input Rise/Fall Time . . . . . . . . . . . . . . . 3 ns
Output Load . . . . . . . . . . . . . . . . . . . . . CL = 30 pF
See Figures 21 and 22
1. LPC interface signals use PCI load test condition
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
20
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
DC Characteristics
TABLE 11: DC OPERATING CHARACTERISTICS (ALL INTERFACES)
Limits
Symbol Parameter
IDD1
Min
Max
Units Test Conditions
Active VDD Current
LCLK (LPC mode) and Address Input (PP mode)=VILT/VIHT
at f=33 MHz (LPC mode) or 1/TRC min (PP mode)
All other inputs=VIL or VIH
Read
12
mA
All outputs = open, VDD=VDD Max
Write2
30
mA
See Note 2
ISB
Standby VDD Current
(LPC Interface)
100
µA
LCLK (LPC mode) and Address Input (PP mode)=VILT/VIHT
at f=33 MHz (LPC mode) or 1/TRC min (PP mode)
LFRAME#=0.9 VDD, f=33 MHz, CE#=0.9 VDD,
VDD=VDD Max, All other inputs ≥ 0.9 VDD or ≤ 0.1 VDD
IRY3
Input Current for Mode
and
ID[3:0] pins
10
mA
LCLK (LPC mode) and Address Input (PP mode)=VILT/VIHT
at f=33 MHz (LPC mode) or 1/TRC min (PP mode)
LFRAME#=VIL, f=33 MHz, VDD=VDD Max
All other inputs ≥ 0.9 VDD or ≤ 0.1 VDD
II
Input Leakage Current for
Mode
and ID[3:0] pins
200
µA
VIN=GND to VDD, VDD=VDD Max
ILI
Input Leakage Current
1
µA
VIN=GND to VDD, VDD=VDD Max
ILO
Output Leakage Current
1
µA
VOUT=GND to VDD, VDD=VDD Max
VIHI
INIT# Input High Voltage
1.1
VDD+0.5
V
VDD=VDD Max
VILI
INIT# Input Low Voltage
-0.5
0.4
V
VDD=VDD Min
VIL
Input Low Voltage
-0.5
0.3 VDD
V
VDD=VDD Min
VIH
Input High Voltage
0.5 VDD
VDD+0.5
V
VDD=VDD Max
VOL
Output Low Voltage
0.1 VDD
V
VOH
Output High Voltage
0.9 VDD
V
T11.0 1307
1. IDD active while a Read or Write (Program or Erase) operation is in progress.
2. For PP mode: OE# = WE# = VIH; For LPC mode: f = 1/TRC min, LFRAME# = VIH.
3. The device is in Ready mode when no activity is on the LPC bus.
TABLE 12: RECOMMENDED SYSTEM POWER-UP TIMINGS
Symbol
Parameter
Minimum
Units
TPU-READ1
Power-up to Read Operation
100
µs
Power-up to Write Operation
100
µs
TPU-WRITE
1
T12.0 1307
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter
TABLE 13: PIN CAPACITANCE (VDD=3.3V, TA=25 °C, f=1 Mhz, other pins open)
Parameter
CI/O
1
CIN1
Description
Test Condition
Maximum
I/O Pin Capacitance
VI/O=0V
12 pF
Input Capacitance
VIN=0V
12 pF
T13.0 1307
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
21
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
TABLE 14: RELIABILITY CHARACTERISTICS
Symbol
Parameter
Minimum Specification
Units
Test Method
NEND1
Endurance
10,000
Cycles
JEDEC Standard A117
100
Years
JEDEC Standard A103
100 + IDD
mA
TDR
1
ILTH1
Data Retention
Latch Up
JEDEC Standard 78
T14.0 1307
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
TABLE 15: CLOCK TIMING PARAMETERS (LPC MODE)
Symbol
Parameter
Min
Max
Units
TCYC
LCLK Cycle Time
30
ns
THIGH
LCLK High Time
11
ns
TLOW
LCLK Low Time
11
-
LCLK Slew Rate (peak-to-peak)
1
-
RST# or INIT# Slew Rate
50
ns
4
V/ns
mV/ns
T15.0 1307
Tcyc
Thigh
0.6 VDD
Tlow
0.5 VDD
0.4 VDD p-to-p
(minimum)
0.4 VDD
0.3 VDD
0.2 VDD
1307 F05.0
FIGURE 6: LCLK WAVEFORM (LPC MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
22
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
AC Characteristics (LPC Mode)
TABLE 16: READ/WRITE CYCLE TIMING PARAMETERS, VDD=3.0-3.6V (LPC MODE)
Symbol
Parameter
Min
TCYC
Clock Cycle Time
30
ns
TSU
Data Set Up Time to Clock Rising
7
ns
TDH
Clock Rising to Data Hold Time
0
TVAL1
Clock Rising to Data Valid
2
Max
Units
ns
11
ns
TBP
Byte Programming Time
20
µs
TSE
Sector-Erase Time
25
ms
25
ms
TBE
Block-Erase Time
TON
Clock Rising to Active (Float to Active Delay)
TOFF
Clock Rising to Inactive (Active to Float Delay)
2
ns
28
ns
T16.0 1307
1. Minimum and maximum times have different loads. See PCI spec
TABLE 17: AC INPUT/OUTPUT SPECIFICATIONS (LPC MODE)
Symbol
Parameter
IOH(AC)
Switching Current High
Min
Max
-12 VDD
-17.1(VDD-VOUT)
Units Conditions
mA
mA
Equation C1
(Test Point)
IOL(AC)
Switching Current Low
16 VDD
26.7 VOUT
ICL
Low Clamp Current
-25+(VIN+1)/0.015
(Test Point)
0 < VOUT ≤ 0.3VDD
0.3VDD < VOUT < 0.9VDD
0.7VDD < VOUT < VDD
-32 VDD
mA
VOUT = 0.7VDD
Equation D1
mA
mA
VDD >VOUT ≥ 0.6VDD
0.6VDD > VOUT > 0.1VDD
0.18VDD > VOUT > 0
38 VDD
mA
VOUT = 0.18VDD
mA
-3 < VIN ≤-1
ICH
High Clamp Current
25+(VIN-VDD-1)/0.015
mA
VDD+4 > VIN ≥ VDD+1
slewr
Output Rise Slew Rate
1
4
V/ns
0.2VDD-0.6VDD load
slewf
Output Fall Slew Rate
1
4
V/ns
0.6VDD-0.2VDD load
T17.0 1307
1. See PCI spec.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
23
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
VTH
LCLK
VTEST
VTL
TVAL
LAD [3:0]
(Valid Output Data)
LAD [3:0]
(Float Output Data)
TON
TOFF
1307 F06.0
FIGURE 7: OUTPUT TIMING PARAMETERS (LPC MODE)
VTH
VTEST
LCLK
VTL
TSU
TDH
LAD [3:0]
(Valid Input Data)
Inputs
Valid
VMAX
1307 F07.0
FIGURE 8: INPUT TIMING PARAMETERS (LPC MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
24
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
TABLE 18: INTERFACE MEASUREMENT CONDITION PARAMETERS (LPC MODE)
Symbol
Value
Units
VTH1
0.6 VDD
V
1
VTL
0.2 VDD
V
VTEST
0.4 VDD
V
1
0.4 VDD
V
1
V/ns
VMAX
Input Signal Edge Rate
T18.0 1307
1. The input test environment is done with 0.1 VDD of overdrive over VIH and VIL. Timing parameters must be met with no more overdrive than this. VMAX specifies the maximum peak-to-peak waveform allowed for measuring input timing. Production testing may use
different voltage values, but must correlate results back to these parameters.
TABLE 19: RESET TIMING PARAMETERS, VDD=3.0-3.6V (LPC MODE)
Symbol
Parameter
Min
Max
Units
TPRST
VDD stable to Reset High
100
µs
TRSTP
RST# Pulse Width
100
ns
TRSTF
RST# Low to Output Float
TRST1
RST# High to LFRAME# Low
TRSTE
RST# Low to reset during Sector-/Block-Erase or Program
48
5
ns
LCLK cycles
10
µs
T19.0 1307
1. There will be a latency due to TRSTE if a reset procedure is performed during a Program or Erase operation,
VDD
TPRST
TRSTP
RST#/INIT#
TRSTE
TRSTF
TRST
Sector-/Block-Erase
or Program operation
aborted
LAD[3:0]
LFRAME#
1307 F08.0
FIGURE 9: RESET TIMING DIAGRAM (LPC MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
25
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
TABLE 20: RESET TIMING PARAMETERS, VDD=3.0-3.6V (PP MODE)
Symbol
Parameter
TPRST
VDD stable to Reset Low
TRSTP
RST# Pulse Width
TRSTF
RST# Low to Output Float
TRST
1
Min
Max
Units
1
ms
100
RST# High to Row Address Setup
ns
48
ns
1
µs
TRSTE
RST# Low to reset during Sector-/Block-Erase or Program
10
µs
TRSTC
RST# Low to reset during Chip-Erase
50
µs
T20.0 1307
1. There will be a reset latency of TRSTE or TRSTC if a reset procedure is performed during a programming or erase operational.
VDD
TPRST
Addresses
Row Address
R/C#
TRSTP
RST#
Sector-/Block-Erase
or Program operation
aborted
TRSTE
TRSTC
TRSTF
TRST
Chip-Erase
aborted
DQ7-0
1307 F09.0
FIGURE 10: RESET TIMING DIAGRAM (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
26
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
AC Characteristics (PP Mode)
TABLE 21: READ CYCLE TIMING PARAMETERS, VDD=3.0-3.6V (PP MODE)
Symbol
Parameter
Min
Max
Units
TRC
Read Cycle Time
270
ns
TRST
RST# High to Row Address Setup
1
µs
TAS
R/C# Address Set-up Time
45
ns
TAH
R/C# Address Hold Time
45
ns
TAA
Address Access Time
120
ns
TOE
Output Enable Access Time
60
ns
TOLZ
OE# Low to Active Output
TOHZ
OE# High to High-Z Output
TOH
Output Hold from Address Change
0
ns
35
0
ns
ns
T21.0 1307
TABLE 22: PROGRAM/ERASE CYCLE TIMING PARAMETERS, VDD=3.0-3.6V (PP MODE)
Symbol
Parameter
Min
Max
Units
TRST
RST# High to Row Address Setup
1
µs
TAS
R/C# Address Setup Time
45
ns
TAH
R/C# Address Hold Time
45
ns
TCWH
R/C# to Write Enable High Time
50
ns
TOES
OE# High Setup Time
20
ns
TOEH
OE# High Hold Time
20
ns
TOEP
OE# to Data# Polling Delay
60
ns
TOET
OE# to Toggle Bit Delay
60
ns
TWP
WE# Pulse Width
100
ns
TWPH
WE# Pulse Width High
100
ns
TDS
Data Setup Time
50
ns
TDH
Data Hold Time
5
ns
TIDA
Software ID Access and Exit Time
150
ns
TBP
Byte Programming Time
20
µs
TSE
Sector-Erase Time
25
ms
TBE
Block-Erase Time
25
ms
TSCE
Chip-Erase Time
100
ms
T22.0 1307
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
27
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
RST#
TRST
TRC
Row Address
Addresses
TAS
TAH
Column Address
TAS
Row Address
Column Address
TAH
R/C#
WE#
VIH
TAA
TOH
OE#
TOE
TOLZ
TOHZ
High-Z
Data Valid
DQ7-0
High-Z
1307 F10.0
FIGURE 11: READ CYCLE TIMING DIAGRAM (PP MODE)
TRST
RST#
Addresses
Row Address
TAS
Column Address
TAH
TAS
TAH
R/C#
TCWH
OE#
TOES
TWP
TOEH
TWPH
WE#
TDH
TDS
Data Valid
DQ7-0
1307 F11.0
FIGURE 12: WRITE CYCLE TIMING DIAGRAM (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
28
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Row
Addresses
Column
R/C#
WE#
OE#
TOEP
DQ7
D
D#
D#
D
1307 F12.0
FIGURE 13: DATA# POLLING TIMING DIAGRAM (PP MODE)
Addresses
Row
Column
R/C#
WE#
OE#
TOET
DQ6
D
D
1307 F13.0
FIGURE 14: TOGGLE BIT TIMING DIAGRAM (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
29
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
A14-0
5555
2AAA
5555
BA
R/C#
OE#
Internal Program Starts
WE#
55
AA
DQ7-0
A0
DATA
BA = Byte-Program Address
1307 F14.0
FIGURE 15: BYTE-PROGRAM TIMING DIAGRAM (PP MODE)
A14-0
5555
2AAA
5555
5555
2AAA
SAX
R/C#
OE#
WE#
Internal Erase Starts
AA
DQ7-0
55
80
SAX = Sector Address
AA
55
30
1307 F15.0
FIGURE 16: SECTOR-ERASE TIMING DIAGRAM (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
30
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
A14-0
5555
2AAA
5555
5555
2AAA
BAX
R/C#
OE#
WE#
Internal Erase Starts
55
AA
DQ7-0
80
AA
55
50
BAX = Block Address
1307 F16.0
FIGURE 17: BLOCK-ERASE TIMING DIAGRAM (PP MODE)
A14-0
5555
2AAA
5555
5555
2AAA
5555
R/C#
OE#
WE#
Internal Erase Starts
DQ7-0
AA
55
80
AA
55
10
1307 F17.0
FIGURE 18: CHIP-ERASE TIMING DIAGRAM (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
31
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
Three-byte sequence for
Software ID Entry
A14-0
2AAA
5555
5555
0000
0001
R/C#
OE#
TWP
WE#
55
AA
DQ7-0
TAA
TIDA
TWPH
BF
90
Device ID
1307 F18.0
Device ID = 60H for SST49LF004B
FIGURE 19: SOFTWARE ID ENTRY AND READ (PP MODE)
A14-0
2AAA
5555
5555
R/C#
OE#
TIDA
WE#
DQ7-0
AA
55
F0
1307 F19.0
FIGURE 20: SOFTWARE ID EXIT (PP MODE)
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
32
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
VIHT
INPUT
VIT
REFERENCE POINTS
VOT
OUTPUT
VILT
1307 F20.0
AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic “0”. Measurement reference
points for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10% ↔ 90%) are <5 ns.
Note: VIT - VINPUT Test
VOT - VOUTPUT Test
VIHT - VINPUT HIGH Test
VILT - VINPUT LOW Test
FIGURE 21: AC INPUT/OUTPUT REFERENCE WAVEFORMS
TO TESTER
TO DUT
CL
1307 F21.0
FIGURE 22: A TEST LOAD EXAMPLE
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
33
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
PRODUCT ORDERING INFORMATION
Device
Speed
SST49LF004B - XXX
Suffix1
-
XX
Suffix2
-
XXX
Environmental Attribute
E1 = non-Pb
Package Modifier
H = 32 leads
Package Type
N = PLCC
W = TSOP (type 1, die up, 8mm x 14mm)
Operating Temperature
C = Commercial = 0°C to +85°C
Minimum Endurance
4 = 10,000 cycles
Serial Access Clock Frequency
33 = 33 MHz
Device Density
004 = 4 Mbit
Voltage Range
L = 3.0-3.6V
Product Series
49 = LPC Firmware Memories
1. Environmental suffix “E” denotes non-Pb solder.
SST non-Pb solder devices are “RoHS Compliant”.
Valid combinations for SST49LF004B
SST49LF004B-33-4C-NHE SST49LF004B-33-4C-WHE
Note: Valid combinations are those products in mass production or will be in mass production. Consult your SST sales
representative to confirm availability of valid combinations and to determine availability of new combinations.
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
34
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
PACKAGING DIAGRAMS
TOP VIEW
Optional
Pin #1
Identifier .048
.042
SIDE VIEW
.495
.485
.453
.447
2
1
32
.112
.106
.020 R.
MAX.
.029 x 30°
.023
.040 R.
.030
.042
.048
.595 .553
.585 .547
BOTTOM VIEW
.021
.013
.400 .530
BSC .490
.032
.026
.050
BSC
.015 Min.
.095
.075
.050
BSC
.140
.125
.032
.026
Note: 1. Complies with JEDEC publication 95 MS-016 AE dimensions, although some dimensions may be more stringent.
2. All linear dimensions are in inches (max/min).
3. Dimensions do not include mold flash. Maximum allowable mold flash is .008 inches.
4. Coplanarity: 4 mils.
32-plcc-NH-3
32-LEAD PLASTIC LEAD CHIP CARRIER (PLCC)
SST PACKAGE CODE: NH
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
35
12/07
4 Mbit Firmware Hub
SST49LF004B
EOL Data Sheet
32-LEAD THIN SMALL OUTLINE PACKAGE (TSOP) 8MM X 14MM
SST PACKAGE CODE: WH
TABLE 23: REVISION HISTORY
Number
Description
Date
00
•
Initial release
Oct 2005
01
•
•
Updated Surface Mount Solder Reflow Temperature information
Added NH package information.
Jan 2006
02
•
Cosmetic update to Figure 2
Feb 2006
03
•
End-of-Life all valid combinations SST49LF004B in this data sheet
Dec 2007
Silicon Storage Technology, Inc. • 1171 Sonora Court • Sunnyvale, CA 94086 • Telephone 408-735-9110 • Fax 408-735-9036
www.SuperFlash.com or www.sst.com
©2007 Silicon Storage Technology, Inc.
S71307-03-EOL
36
12/07