Model PD0810J5050S2 Rev C Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description The PD0810J5050S2 is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD0810J5050S2 is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD0810J5050S2 is matched to 50 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: GSM, WCDMA, Home Cordless, and RFID. The PD0810J5050S2 does not include the resistive element and therefore, requires an external resistor for operation. The PD0810J5050S2 is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • • Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature 800-1000 MHz 21 dB Isolation (output ports) 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External Resistor required Min. 800 Typ. Max 1000 50 50 19 0.5 0.3 1 21 14 17 0.6 0.8 4 2 +85 -55 Unit MHz Ω Ω dB dB dB Degrees dB Watts ºC * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View 2X .026 [0.65] .021±.002 [0.53±0.05] .039 [0.98] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Bottom View (Far-side) Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation GND Input GND Output 1 GND Output 2 1 2 3 6X .009 [0.22] 6 5 6X .012 [0.30] 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD0810J5050S2 Rev C Typical Broadband Performance: 500 MHz. to 8.0 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 Frequency [MHz] Isolation -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 -36 2500 7000 7500 8000 7000 7500 8000 5000 5000 4500 4000 3500 3000 2500 2000 Frequency [MHz] 0 Frequency [MHz] (315) 432-8909 (800) 411-6596 +44 2392-232392 1500 8500 8000 7500 7000 6500 6000 5500 5000 -20 4500 -2 4000 -15 3500 -1.5 3000 -10 2500 -5 -1 2000 -0.5 1000 0 500 0 2000 6500 5 1500 6000 0.5 1500 6500 10 1000 6000 1 1000 5500 15 deg 1.5 500 4500 Phase Balance 20 500 [dB] Amplitude Balance [dB] 4000 Frequency [MHz] 2 USA/Canada: Toll Free: Europe: 5500 Frequency [MHz] 3500 3000 2500 500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -36 3000 -33 -36 2500 -30 -33 2000 -27 -30 1500 -24 -27 1000 -21 -24 2000 -18 -21 1500 -18 1000 [dB] -9 500 [dB] Return Loss - Input 0 Available on Tape and Reel for Pick and Place Manufacturing. Model PD0810J5050S2 Rev C Typical Performance: 700 MHz. to 1100 MHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 1100 1100 10 0.5 5 Frequency [MHz] 950 900 850 -20 700 -2 1100 -15 1050 -1.5 1000 -10 950 -1 800 0 -5 750 0 -0.5 900 1050 1 850 1050 15 deg 1.5 800 1000 Phase Balance 20 750 1000 Amplitude Balance 2 700 950 Frequency [MHz] Frequency [MHz] [dB] 900 700 1100 1050 1000 -3.6 950 -3.3 -36 900 -3.0 -33 850 -2.7 -30 800 -2.4 -27 750 -2.1 -24 850 -1.8 -21 800 -18 750 [dB] 0.0 700 [dB] Return Loss - Input 0 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 1100 1050 1000 950 900 850 800 750 -36 700 [dB] -15 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD0810J5050S2 Rev C Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0810J5050S2 is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. Pad Footprint w/ 0603 Resistor Locations 6X .014 [0.35] 4X .012 [0.30] 6X .010 [0.25] .033 [0.85] 6X .002 [0.05] R1 Plated thru holes to ground Circuit Pattern 3X Transmission Line Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model PD0810J5050S2 Rev C Packaging and Ordering Information Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD0810J5050S2 Rev C USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.