Embedded Power for Business-Critical Continuity Rev. 01.11.06 DS1500-3 1 of 4 DS1500-3 1500 Watts 12V Distributed Power System Distributed Power Bulk Front-End Total Output Power: 1500 Watts +12vdc Main Output; +3.3vdc Stand-by Output Wide Range Input voltage: 90 - 264VAC 180 - 264vac 1500w 90 - 264vac 910W Electrical Specifications Special Features • Active Power Factor Correction • EN61000-3-2 Harmonic Compliance • Active AC Inrush Control • 2U X 3U Form Factor 7.5" long • 15W/ in3 • +12vdc Output • +3.3vdc Stand-By • Hot Plug Operation • N + 1 Redundant • Internal OR'ing Main and Stand-by • Active Current Sharing • Internal Cooling Fans (60mm x 38mm) • I2C Communication Interface Bus • EERPOM for FRU Data • Green LED Status, Power OK • Amber LED Status, Power Failed • Internal Fan Speed Control • Fan Fail Output Signal • INTEL, SSI Std. Logic Timing • INTEL, SSI Std. FRU Data Format • AC shutdown <85VAC or 170VAC • One Year Warranty Safety UL/cUL 60950 (UL Recognized) 1st edition (UL)60950-1-03 CSA NEMKO+ CB Report EN60950 EN60950 CE Mark China CCC CB Test Report Input Input range Frequency Inrush current 90-264 VAC, 910w 180 - 264 vac, 1500w 47-63 Hz, single phase AC Efficiency 35A maximum inrush current >80% typical at full load, high line Conducted EMI FCC Subpart J EN55022 Class A Radiated EMI FCC Subpart J EN55022 Class A Power factor 0.99 typical Leakage current 0.75mA @ 240VAC Hold up time 12ms minimum Output Main DC voltage +12v @ 74A (90VAC) or 123A (180VAC) Stand-By +3.3vsb @ 7A Adjustment range Factory Set, no pot adjustments Regulation Over current Under voltage +12vdc; ±3%; +3.3vsb; ±3% +12vdc; 110 - 130% latches off if overcurrent lasts over 1.5 seconds, otherwise it is auto recovery. +3.3vsb, 7A - 105% - 130% +12vdc; 13.7v ±7% +3.3vsb; 4.0v ±7% +12vdc; 11.0 - 11.4vdc Turn-on delay +12vOutput Rise Time <3 Second max 5 - <200mS, Monotonic Rise I Share 12V 15% from 50 - 100% load Over voltage Embedded Power for Business-Critical Continuity Rev. 01.11.06 DS1500-3 2 of 4 Logic Control PS_ON POK PS FAIL AC OK PRESENT FAN FAIL PS_KILL An active low signal that turns on the 12vdc power rail. When this signal High, or left open, the 12vdc output turn off. The 3.3Vsb output remains on. Is a power good signal to be pulled low by the power supply to indicate that all the outputs are within regulation limits of the power supply. (turn-on delay 100 - 500mS) In the event of a power supply failure (OVP at any output, UV at any output, OTP or other electrical failure), this signal shall go to a High state. High when AC is not OK, Low if AC is OK Low i f PSU is Present, High if not Present; Pull high in system. Low if one or both fans have failed This pin shall quickly turn off the power supply and prevent arching of the DC output contacts. Environmental Specifications Operating temperature: -10° to 50°C ; 50% power derating at 70°C Storage temperature: Altitude, operating 10,000ft. -40°C to +85°C Electromagnetic EN61000-3-2, -3-3 susceptibility / Input transients: EN61000-4-2, 4.3, 4-4, -4-5, 4-11 Level EN55024:1998 RoHS, RS5 Humidity: 5 to 95% RH, non-condensing Shock and vibration specificatons complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated) 500K Hrs at full load, 50°C Anti-smoke Emission Due to internal overload or internal failures Fan life: 70,000 hrs @ 40°C Ordering Information Output Nominal Output Voltage Set Point Set Point Tolerance Total Regulation Minimum Current Maximum Current Output Ripple P/P Main (>90VAC) 12.00vdc ±0.2% ±3% 0A 74A 120mV Main (180VAC) 12.00vdc ±0.2% ±3% 1.0A 123A 120mV Std-By 3.3vdc ±1% ±3% 0.5A 7.0A 50mV Embedded Power for Business-Critical Continuity Rev. 01.11.06 DS1500-3 3 of 4 AIRFLOW DIRECTION 190.5 7.5" (162.9) 65.5 2.58" 19.3 AC CABLE RETAINER BLACK 3D VIEW HF GREEN EMI CLIP LAIRD 771062031 7.2 0.283" 165.6 6.52" MODEL LABEL (2X) EMI CLIP LAIRD 77-020 71.1 2.80" 143.3 5.65" (4X) EMI CLIP LAIRD 77-020 124.45 4.90" STATUS LED INDICATORS AC INLET 15A C14 TYCO P/N 1-1450330-8 OR FCI P/N 51939-055 NOTE: Dimensions given in mm and inches. Power Supply Condition No AC power to all PSU No AC power to this PSU only (includes No output, over voltage, over temperature) AC present / Standby Output On Power supply DC outputs ON and OK Power supply failure (over current) Power Supply LED's PWR FAIL (green) (amber) Off Off OFF On Blinking ON OFF Off Off Blinking Embedded Power for Business-Critical Continuity DC Output Connector Pinout Assignment Astec Power Rev. 01.11.06 DS1500-3 4 of 4 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Technical Support: +1 888 41 ASTEC or +1 407 241 2752 Male connector as viewed from the rear of the supply P1 - Unit FCI Power blade FCI p/n 51939-055 P1 - Mate Mating Connector (System side) FCI Power blade Part number 51915-023 AC Input Connector EN60320 Type C14 Pin Signal Name PB P1 PB P2 PB P3 PB P4 PB P5 PB P6 PB P7 PB P8 A1 A2 A3 A4 A5 A6 A7 B1 B2 B3 B4 B5 B6 B7 C1 C2 C3 C4 C5 C6 C7 D1 D2 D3 D4 D5 D6 D7 +12V +12V RETURN (Pre-mate) +12V +12V RETURN (Pre-mate) +12V +12V RETURN (Pre-mate) +12V +12V RETURN (Pre-mate) +3V3 STAND-BY +3V3SB RETURN PS_PRESENT ( Power Supply Seated) - (short pin) POK (Output Power Ok) PS FAIL (Failure Signal) SPARE SPARE +3V3 STAND-BY +3V3SB RETURN PSON (Power Enable Signal) PSKILL (Power Supply Fast Shutdown) - (short pin) SDA (I2C Data Signal A2 (I2C Address BIT 2 Signal) FAN FAIL (Fan Fail Signal) +3V3 STAND-BY +3V3SB RETURN AC OK (AC Input Present) +12V RMT SENSE +12V RMT SENSE RETURN A1 (I2C Address BIT 1 Signal) +3V3 STAND-BY RMT SENSE Return (-) +3V3 STAND-BY +3V3SB RETURN 12IS (+12V Current Share) SPARE SCL (I2C Clock Signal) A0 (I2C Address BIT 0 Signal) +3V3 STAND-BY RMT SENSE (+) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Units 2111-2116, Level 21 Tower 1, Metroplaza 223, Hing Fong Road Kwai Fong, New Territories Hong Kong Telephone: +852 2437 9662 Facsimile: +852 2402 4426 For global contact, visit: www.astecpower.com [email protected] While every precaution has been taken to ensure accuracy and completeness in this literature, Astec Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Printed in US A Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Power Inbound Power Integrated Cabinet Solutions Outside Plant Precision Cooling Site Monitoring and Services EmersonNetworkPower. com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2006 Emerson Electric Co.