S33201M . Semiconductor Rail to Rail Single OP AMP Description The S33201M is operational amplifiers provide rail-to-rail operation on both the input and output. The inputs can be driven as high as 200mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50mV of each rail. This rail-to-rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (± 0.9 V) yet can operate with a supply of up to +12V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. Features • Low Voltage, Single Supply Operation (+1.8 V and Ground to +12 V and Ground) • Input Voltage Range Includes both Supply Rails • Output Voltage Swings within 50 mV of both Rails • No Phase Reversal on the Output for Over-driven Input Signals • High Output Current (ISC = 30 mA, Typ) • Low Supply Current (ICC = 0.9 mA, Typ) • 600Ω Output Drive Capability • Typical Gain Bandwidth Product = 2.2 MHz Applications • Low cost general purpose applications • Cellular phones • A/D buffer • DSP interface • Smart card readers • Portable test instruments • Keyless entry • Telephone systems • Audio applications • Digital still cameras • Hard disk drives • MP3 players Ordering Information Type NO. S33201M Marking 332 Package Code SOT-25 KSD-I5O002-000 1 S33201M Outline Dimensions unit : mm Internal Block 0.95 Typ. 2.60~3.00 1.50~1.70 5 2.80~3.00 1 2 4 1.00~1.20 0.45 Max. 0.95 Typ. 3 0.10 Max. 0.19 Max. 0.40 Min. Circuit Schematic KSD-I5O002-000 2 S33201M Absolute maximum ratings Characteristic Symbol Rating Unit Supply Voltage (VCC to VEE) VCC +13 V Input Differential Voltage Range VIDR Note1 V Common Mode Input Voltage Range (Note2) VCM VCC + 0.5V to VEE - 0.5V V Power Dissipation PD 0.5 W Operating Ambient Temperature Range TOPR -40 to 85 °C Storage Temperature TSTG -55 to 150 °C Notes ; 1. The differential input voltage of each amplifier is limited by two internal parallel back-to-back diodes. for additional differential input voltage range, use current limiting resistors in series with the input Pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500mV. Electrical Characteristics (Ta=25℃) VCC (V) Characteristic Output Voltage Swing (Note) Supply Current Unit 2.0 3.3 5.0 VOH (Min) 1.9 3.15 4.85 V VOL (Max) 0.10 0.15 0.15 V ICC 1.125 1.125 1.125 mA Specifications at VCC = 3.3V are guaranteed by the 2.0V and 5.0V tests. VEE = GND. Note : (RL = 10 ㏀) Electrical Characteristics (VCC = +5.0V, VEE = GND, Ta=25℃, unless otherwise noted.) Characteristic Input Offset Voltage Input Offset Voltage Temperature Coefficient Symbol VIOS ∆VIO/∆T Test Condition Min. Typ. Max. Unit VCM 0V to 0.5V, VCM 1.0V to 5.0V - - 6 ㎷ RS=50Ω - 2 - ㎶/℃ Input Bias Current IIB VCM=0V to 0.5V VCM=1.0V to 5.0V - 300 500 ㎁ Input Offset Current IIO VCM=0V to 0.5V VCM=1.0V to 5.0V - 5 50 ㎁ Common Mode Input Voltage Range VICR VEE - VCC V - KSD-I5O002-000 3 S33201M Electrical Characteristics (cont.) (VCC = +5.0V, VEE = GND, Ta = 25℃, unless otherwise noted.) Characteristic Large Signal Voltage Gain (VCC=+5V, VEE=-5V) Symbol Test Condition Min. Typ. Max. Unit RL=10 ㏀ 50 300 - ㎸/V RL=600Ω 25 250 - ㎸/V RL=10 ㏀ 4.85 4.95 - V RL=600Ω 4.75 4.85 - V RL=10 ㏀ - 0.05 0.15 V - 0.15 0.25 V AVOL VOH Output Voltage Swing (VID=±0.2V) VOL RL=600Ω Common Mode Rejection CMR (VIN = 0V to 5.0V) 60 90 - dB Power Supply Rejection Ratio PSRR VCC/VEE = 5.0V/GND to 3.0V/GND 60 90 - dB Source Current ISO - 20 30 - ㎃ Sink Current ISI - 10 20 - ㎃ Supply Current ICC - - 0.9 1.5 ㎃ Slew Rate SR (VS=±2.5V, VO=-2.0V to 2.0V, RL=2 ㏀, AV=1) - 1 - V/㎲ - - 2.2 - ㎒ Output Short Circuit Current Gain Bandwidth Product GBW KSD-I5O002-000 4 S33201M Electrical Characteristic Curves Fig. 1 ICC vs VCC ㎃ ㎁ Fig. 2 IIB vs VCC Fig. 3 VOH vs VCC Fig. 4 VOL vs VCC Ω V ㎷ Ω Fig. 5 VOP-P vs f ㏈ Fig. 6 CMR vs f Ω ㎐ ㎐ KSD-I5O002-000 5 S33201M Fig. 8 GV vs f ㏈ Fig. 7 ISC vs VOUT ㎃ Ω ㎐ The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-I5O002-000 6