Issue: 02 Specification AXLE10 Oscillator type : TCXO Parameter min. Frequency range Standard frequencies Frequency stability Initial tolerance vs. temperature in operating temperature range (steady state) 1.25 vs. supply voltage variation vs. load change long term (aging) per year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC linearity EFC input impedance RF output Signal waveform Load Rise & decay time Symmetry (duty cycle) typ. max. Unit 25 MHz MHz ppm ppm 12.800 / 19.44 ±1 Frequency stability Date: 2005-05-22 Condition @+25°C Temperature -0.5 -1.5 -2.5 0.5 1.5 2.5 ± 0.3 ± 0.1 ±1 ppm ppm ppm ppm ppm ppm - 0°C ~ +50°C -20°C ~ +70°C -30°C ~ +75°C VS ± 5 % RL ± 10 % @ +40°C ±5 0.5 0.3 ± 15 4.5 3.0 ppm V V Option II =”50” Option II =”33” Option I “05” “15” “25” positive % kΩ 10 HCMOS 15 5 55 45 Start-up time Supply voltage VS 10 ms 5.25 V 3.47 V 10 mA 20 mA Pin 2 = HIGH or OPEN: Output Enable Pin 2 = LOW: Output High Z -40 +85 °C -40 +85 °C 15.1x9.5x6.0 max mm 3 gram Tape & reel 1500 V 4.75 3.13 Current consumption (steady state @ +25°C) Enable/disable function Operable temperature range Storage temperature range Enclosure (see drawing) Weight Packing ESD Sensitivity pF ns % 5.0 3.3 @ VS/2 @ VS nom – 5% Option II =”50” Option II =”33” Option II =”50” Option II =”33” IEC 61837 CO 27 IEC 60286-3 HBM as in IEC 610004-2 Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated Ordering Code: Model (Specification) AXLE10 GmbH & Co. KG Wasemweg 5 D-74921 Mosbach Germany Option I 25 Option II Frequency [MHz] 33 12.800 AXLE10 page 1(2) www.axtal.com phone: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections Pin # Symbol 1 VC 2 E/D 3 GND 4 RF OUT 5 N.C. 6 Vs Function Control Voltage (EFC) Enable/Disable Input Ground RF Output No Connection Supply Voltage Note: Length max 15.1 mm, Height max. 6.0 mm Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60679-1 clause ... 4.3 2-17 4.6.2 2-20 2-58 4.6.3 2-27 4.6.8 Bump* 2-29 4.6.6 Free fall* 2-32 4.6.9 Test conditions Enclosure styles as in IEC 60679-3 or 61837, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Vibration, sinusoidal* 2-6 4.6.7 Rapid change of temperature Dry heat 2-14 4.6.5 2-2 4.6.14 Damp heat, cyclic* 2-30 4.6.15 Cold 2-1 4.6.16 Climatic sequence* 1-7 4.6.17 Damp heat, steady state* Endurance tests - ageing - extended aging 2-3 4.6.18 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.6.14, 4.6.15 (1st cycle), 4.6.16, 4.6.15 (5 cycles) Test Ca, 56 days 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 5 D-74921 Mosbach Germany AXLE10 page 2(2) www.axtal.com phone: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]