ADSL Magnetics Tioga • • TM01388 Designed to comply with the requirements of GR1089, UL1950, EN60950, BABT and CSA950 to provide a supplementary insulation barrier with a working voltage of 250V • Operating and storage temperature range: -40° to +85° C • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias Minimum interwinding breakdown voltage of 1500 Vrms ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Inductance1 µH ±5% Leakage Inductance2 µH max Direct Capacitance3 pF max Chip : Line Line Side Line Side 1&8 Chip Side 1:1 280 8 50 1.8 Part Number S560-6600-CA Longitudinal Balance2 dB min Insertion Loss2 dB max Frequency Response2 dB max Total Harmonic Distortion4 dB max Line Side 1.1 MHz 100 kHz 40 kHz 300 kHz 20 Vpp 100 kHz 1.8 55 0.5 ±0.3 -70 DCR Ω max All measurements are made with pins 2 and 3 connected and pins 6 and 7 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measured at 100 kHz, 0.1 Vac 3. Interwinding capacitance measured at 10 kHz, 0.1 Vac 4. Measured with line impedance of 100 Ω and chip impedance of 100 Ω SCHEMATIC S560-6600-CA 8 1 6 3 7 2 5 4 Chip Line ©2001 Bel Fuse Inc. Specifications subject to change without notice. 10.01 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 ADSL Magnetics Tioga TM01388 MECHANICAL 1 2 3 S560-6600-CA 0.615 [15.62] 8 7 6 0.098 [2.50] 0.048 [1.22] 4 0.077 [1.96] 5 Suggested PCB Pad Layout 0.510 [12.95] max 0.475 [12.07] max 0.460 [11.68] max 0.024 [0.60] 0.098 [2.50] 0.004 [0.10] 0.492 [12.50] 8 Edges 0.600 [15.24] max Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2001 Bel Fuse Inc. Specifications subject to change without notice. 10.01 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2