ADSL Magnetics For Texas Instruments AC5 (CO) TM01338 Designed to comply with the requirements of UL1950 and EN60950 to provide a supplementary insulation barrier with a working voltage of 250V • Operating and storage temperature range -40° to +85°C • Meets IEC 695, 2-2 flammability requirements • UL File Number E150991 • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • BABT certificate number: NC4/000185 • • Minimum interwinding breakdown voltage of 2000 Vrms Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias • ELECTRICAL SPECIFICATIONS at 25°C Turns Ratio ±2% Inductance1 µH ±5% Leakage Inductance1 µH max Interwinding Capacitance pF max Chip : Line Line Side Line Side 1&8 Chip Side 1 : 1.9 400 6 60 1.1 Part Number S560-6600-Z6 DCR Ω max Longitudinal Balance2 dB min Insertion Loss2 dB max Frequency Response2 dB max Harmonic Distortion2 dB max Line Side 30 kHz 1.1 MHz 300 kHz 30 kHz 1.1MHz 100 kHz 15 Vpp 1.0 50 0.25 ±0.35 -80 All measurements are made with pins 2 and 3 connected and pins 6 and 7 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measurements made with 100Ω source and 28Ω load impedance SCHEMATIC S560-6600-Z6 8 1 6 3 Chip Line 7 2 5 4 ©2001 Bel Fuse Inc. Specifications subject to change without notice. 10.01 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 ADSL Magnetics For Texas Instruments AC5 (CO) TM01338 MECHANICAL 1 0.048 (1.22) 4 0.098 (2.50) S560-6600-Z6 0.077 (1.96) 0.615 (15.62) 8 5 Suggested PCB Pad Layout 0.510 (12.95) max 0.475 (12.07) max 0.460 (11.68) max 0.024 (0.60) 0.098 (2.50) 0.492 (12.50) 0.004 (0.10) 8 Edges 0.600 (15.24) max Dimensions are in inches (millimeters). Standard dimension tolerance is ±0.005 (0.13) unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2001 Bel Fuse Inc. Specifications subject to change without notice. 10.01 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2