HDSL & G.SHDSL Magnetics GlobespanVirata TM02308 • Designed for G2237 DSP and 3137 AFE • Operating and storage temperature range: -40° to +85° C • Designed to comply with the requirements of GR1089 power fault, UL1950 and EN60950 to provide an insulation barrier with a working voltage of 250V • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias • Minimum interwinding breakdown voltage of 1500 Vrms • Minimum interwinding breakdown voltage of 600 Vrms between line center tap or pin 1 and 2 ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Inductance1 mH ±5% Leakage Inductance2 µH max Chip : Line Line Side Line Side Chip Side 1:4 2 10 0.45 Part Number S560-6600-GK DCR Ω max Longitudinal Balance3 dB max Insertion Loss dB max Harmonic Distortion3 dB max Line Side 20 kHz 300 kHz 100 kHz 2 Vrms 5 kHz 2.6 -55 0.5 -80 All measurements are made with pins 2 and 4 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measured at 100 kHz, 0.1 Vac 3. Measured with line impedance of 135 Ω and chip impedance of 8.4 Ω SCHEMATIC S560-6600-GK 1 9 4 Line Chip 8 2 7 5 ©2002 Bel Fuse Inc. Specifications subject to change without notice. 11.02 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 HDSL & G.SHDSL Magnetics GlobespanVirata TM02308 MECHANICAL Suggested PCB Pad Layout 5 1 S560-6600-GK 0.100 [2.54] 0.741 [18.82] 0.060 [1.52] 6 10 0.087 [2.21] 0.028 [0.71] 0.100 [2.54] 0.585 [14.86] max 0.540 [13.72] max 0.500 [12.70] max 0.005 [0.13] 0.606 [15.39] 10 edges 0.699 [17.75] max Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2002 Bel Fuse Inc. Specifications subject to change without notice. 11.02 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2